Eiki LC-X2U, LC-X2UL User Manual

Download

MULTIMEDIA PROJECTOR

MODEL LC-X2U

LC-X2UL

(Without Lens)

OWNER’S INSTRUCTION MANUAL

INFORMATION TO THE USER

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the owner’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

SAFETY PRECAUTIONS

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This Projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the

power outlet. Do not try to defeat this safety feature.

Intense light source. Do not stare directly into the projection lens as possible eye damage could result.

Be especially careful that children do not stare directly into the beam.

The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button. Do not look into the Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.

If the Projector will not be used for an extended time, unplug the new Projector from the power outlet. This Projector should be set in the way indicated. Never hang the projector, or fall down on its side. It may result in fire hazard.

READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE

IMPORTANT:

For your protection in the event of theft or loss of this LC Data-Grade

projector, please record the Model Number and Serial Number located Model No:

LC-X2U/X2UL

on the rear of unit and retain this information. Refer to these numbers whenever you call upon your authorized dealer regarding this product. Serial No•_______________

Do not discard shipping

These items may be needed for storage or future servicing.

carton and packing materials.

IMPORTANT SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer’s instructions, and should use a mounting kit approved by the manufacturer.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other material, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface This projector should never be placed near or r a radiator or heat register.

This projector should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord will be abused by persons walking on it.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following

the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has

been damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

This projector is equipped with a grounding type AC line plug. Should you be unable to insert the plug into the outlet, contact your electrician. Do not defeat the safety purpose of this grounding type plug.

Follow all warnings and instructions marked on the projectors.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will

prevent damage due to lightning and powerline surges.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector,

and can also be dangerous

PAGE

FEATURES AND DESIGN 5

INTRODUCTION 5 COMPATIBILITY 5 IMAGE RESOLUTION 5 AUTOMATIC MULTISCANNING SYSTEM 5 SCREEN MODE 5 MULTILANGUAGE 5 UNPACKING THE PROJECTOR 5 TRADEMARKS 5

INSTALLATION 6-9

NAME OF EACH PART OF THE PROJECTOR 6

SETTING-UP THE PROJECTOR 7

MOVING THE PROJECTOR 8 POWER REQUIREMENTS 9

CONNECTING THE PROJECTOR 10-21

TERMINAL OF THE PROJECTOR 10-11 CONNECTING THE COMPUTER 12-19 CONNECTING THE VIDEO EQUIPMENT 20-21 BEFORE OPERATION 22-31 CONTROLS AND INDICATOR 22-23 OPERATION OF THE REMOTE CONTROL 24-28 WIRELESS REMOTE CONTROL UNIT 24-26 WIRELESS REMOTE CONTROL UNIT 27-28 CONTROL THE PROJECTOR 29-31 DIRECT OPERATION 29 MENU OPERATION 30-31

BASIC OPERATION 32-51

TURNING ON/OFF THE PROJECTOR 32 DIRECT OPERATION 33-34

MODE SELECT 33

SOUND VOLUME ADJUSTMENT 33

SOUND MUTE FUNCTION 33

ZOOM ADJUSTMENT 33

FOCUS ADJUSTMENT 33

LENS SHIFT ADJUSTMENT 33

DIGITAL ZOOM FUNCTION 34

NORMAL PICTURE FUNCTION 34

FREEZE PICTURE FUNCTION 34

NO SHOW FUNCTION 34

PAGE

P-TIMER FUNCTION 34

AUTO IMAGE FUNCTION 34

CURSOR FUNCTION 34

MENU OPERATION 35-36

MODE SELECT 35

SOUND ADJUSTMENT 36

LANGUAGE ADJUSTMENT 36

VIDEO MODE . 37-39

COLOR SYSTEM SELECT 37 VIDEO SOURCE SELECT 37 PICTURE IMAGE ADJUSTMENT 38 PICTURE SCREEN ADJUSTMENT 39

COMPUTER MODE 40-49

COMPUTER SYSTEM SELECT 40 COMPATIBLE COMPUTER SPECIFICATIONS 41 AUTO IMAGE FUNCTION 42 PICTURE IMAGE ADJUSTMENT 43 PICTURE POSITION ADJUSTMENT 44 PC ADJUSTMENT 45-48 PICTURE SCREEN ADJUSTMENT 49

OTHER FUNCTION SETTING 50-52

BLUE BACK 50-51 DISPLAY 50-51 REVERSE T/B 50-51 REVERSE L/R 50-51 SPLIT WIPE 50-51 POWER MANAGEMENT 50-51 USB (Mouse or Control) 50-51 REMOTE CONTROL (Mode 1 or Mode 2) 50-51 LAMP AGE 52

APPENDIX 53-57

MAINTENANCE 53..55

TEMPERATURE WARNING INDICATOR 53

AIR FILTER CARE AND CLEANING 53

LAMP REPLACEMENT 54

CLEANING THE LENS 55

TROUBLESHOOTING 55-56 TECHNICAL SPECIFICATIONS 57

FEATURES AND DESIGN

INTRODUCTION

The multimedia projector that combinesx powertul and sophisticated teatures with easy-to-use, intuitive controls. Built-in multimedia features include audio, a palette of 16.77 million colors and active matrix liquid crystal display (LCD) technology. The projector is ideal for high-performance business, training and imaging applications that demand exceptional color quality.

COMPATIBILITY

The projector is compatible with many different types of personal computers and video devices, including:

• IBM-compatible computers, including laptops, up to 1280 x 1024 resolution.

• Apple Macintosh and PowerBook computers up to 1280 x 1024 resolution.

• Various VCRs, video disc players, video cameras, DVD players, satellite TV tuners or other AV equipment using any of the

worldwide video standards, including NTSC, NTSC4.43, PAL, PAL-M, PAL-N and SECAM.

IMAGE RESOLUTION

The resolution of the projector’s projected image is 1024 x 768. The projector displays computer images just as they appear on your computer’s monitor. Screen resolutions between 1024 x 768 and 1280 x 1024 are compressed to 1024 x 768. The projector cannot display screen resolutions above 1280 x 1024. If your computer’s screen resolution is higher than 1280 x 1024, reset it to a lower resolution before you connect the projector.

AUTOMATIC MULTISCANNING SYSTEM

This projector can detect display signals from most personal computers currently distributed. It is free from complicated adjustments to project picture images from PC.

SCREEN MODE

Screen display can be selected among; Computer mode

Video mode --- Regular (4:3), Wide (16:9)

MULTILANGUAGE

MENU DISPLAY is displayed with; English, German, French, Italian, Spanish and Japanese.

UNPACKING THE PROJECTOR

The projector comes with the parts listed below. Check to find all the parts are included. If any parts are missing, contact an authorized dealer or service station.

• Owner’s Manual.

• Wireless Remote Control Unit.

• Remote Control Cable. • Batteries for Remote Control Units.

• VGA Cable. • Mouse Cable for PS/2 port.

• Mouse Cable for serial port. • Mouse Cable for ADB port.

• VGA/MAC Adapter. • Protective Dust Cover

• Lens Cover.

--- True, Digital zoom (Expand, Compress, Panning)

• AC Power Cord.

• Wireless/Wired Remote Control Unit.

TRADEMARKS

• Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc.

• IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

•Windows is a trademarks or registered trademarks of Microsoft Corporation. )ther trademarks are the property of their

respective owners.

• This projector is basically designed to project on a flat projection

THIS PROJECTOR SHOULD BE SET IN THE WAY INDICATED. NEVER HANG THE PROJECTOR, OR FALL DOWN ON ITS SIDE. IT MAY RESULT IN FIRE HAZARD.

surface.

• This projector can be focused from 4.9’ (1.5 m) ~ 80.7’ (24.6 m).

• Refer to the figure below as an example when positioning the projector to the screen.

Picture tilt and projection angle can be adjusted by twisting ADJUSTABLE FEET. Projection angle can be adjusted up to 4 degrees by rotating Adjustable Feet.

MOVE THE PROJECTED IMAGE POSITION Adjust the projected image (maximum 760 mm downward or upward on the 100” screen) by using lens shift function. (see page 33.)

This projector is equipped with a cooling fan to protect it from overheating. Pay attention to the following to ensure the ventilation and avoid a possible risk of fire and malfunction.

•Do not cover the vents with papers or other materials.

•Keep the rear grill at least 3.3’ (1 m) away from any object.

•Make sure that there are no objects under the projector. An object under the projector may prevent the projector from taking the cooling air through the bottom vent.

Use the carry handle when moving the projector. Replace the lens cover and rotate the adjustable feet fully clockwise.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

• Do not drop or give a shock to the projector, otherwise damage or malfunction may result.

• When carrying the projector, use a Eiki recommended Carrying Case.

• Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause damage to the projector. To transport the projector through a courier or transport service, use a Eiki recommended Case.

• For a carrying or transportation cases, contact a Eiki authorized dealer.

Your projector uses nominal input voltages of 100-120 VAC. The projector automatically selects the correct input voltage. The projector is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure what type of power is supplied to your building.

COMPUTER INPUT-1 TERMINAL (ANALOG HDB

15-PIN)

Used to connect a computer to the projector.

COMPUTER INPUT-1 RMINAL (DIGITAL MDR 20-

PIN)

Used to connect a computer to the projector.

COMPUTER INPUT-2 JACKS (BNC TYPE x 5)

Used to connect a computer to the projector.

MONITOR OUTPUT TERMINAL (ANALOG HDB

15-PIN)

Used to connect a monitor to the projector.

COMPUTER AUDIO INPUT-i JACKS (R and L)

Used to connect an audio output from the computer to the

projector.

COMPUTER AUDIO INPUT-2 JACKS (R and L)

Used to connect an audio output from the computer to the projector.

AUDIO MONITOR OUTPUT JACKS (R and L)

Used to connect an audio input from audio equipment to the Projector.

CONTROL PORT-1 CONNECTOR

Used to connect a mouse cable to the projector.

CONTROL PORT-2 CONNECTOR

Used to connect a mouse cable to the projector.

USB PORT-1 CONNECTOR

Used to connect a computer to the projector.

USB PORT-2 CONNECTOR

Used to connect a computer to the projector.

SERIAL PORT TERMINAL (DB9)

Used to connect a computer to the projector.

WIRED REMOTE JACK

When using the wired remote control, connect the remote cable to this jack.

VIDEO INPUT JACKS-1 (BNC TYPE x 3)

Used to connect a video source to the projector.

S-VIDEO INPUT JACK-1

Used to connect a S-VHS video source to the projector.

AUDIO INPUT JACKS-1 (R and L)

Used to connect an audio source to the projector.

VIDEO INPUT JACKS-2 (BNC TYPE x 3)

Used to connect a video source to the projector.

S-VIDEO INPUT JACK-2

Used to connect a S-VHS video source to the projector.

AUDIO INPUT JACKS-2 (R and L)

Used to connect an audio source to the projector.

VIDEO MONITOR OUTPUT JACKS (BNC TYPE x

Permits video connection to a monitor.

VIDEO MONITOR (S-VIDEO) OUTPUT JACK

Permits S-VHS video connection to a monitor.

AUDIO MONITOR OUTPUT JACKS (R and L)

Permits audio connection to a monitor.

Personal computers can be connected to the HDB1 5-pin (VGA) terminal on the projector.

• Connect the computer to these terminals using the VGA cable and VGA/MAC adapter (provided).

CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions.

For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.

Digital output signal from the computer can be connected to the DIGITAL terminal (MDR 20-pin). When using this input, Graphic Accelerator Board designed for this projector should be installed into your computer and set-up the computer configuration following instruction included in the Graphic Accelerator Board package. Refer to DIGITAL INPUT CONNECTION on page 15 and 17.

Personal computers can be connected to the computer input (Red, Green, Blue, Horiz. Sync. and Vert. Sync.) on the projector.

• Connect the computer to these jacks using the BNC cables (not provided).

• Connect audio outputs from your computer to these jacks using the audio cable (not provided).

• When the computer is operated by projector’s remote control unit, connect three different type of cables (provided) between projector control port and computer mouse port or serial port.

COMPUTER TYPE CABLE

IBM Compatible computer with PS/2 mouse port. Mouse Cable for PS/2 port.

IBM Compatible computer with serial port. Mouse Cable for Serial port. Apple Macintosh computer with ADB mouse port. Mouse Cable for ADB port.

This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2). When video source (“Video 1” or “Video 2”) is selected, this terminal outputs Computer 1 input information. An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector.

• Connect the monitor to this terminal usinq the VGA cable (not provided).

Pin No./Signal 1 Red input 2 Green input 3 Blue input 4 Sense 2 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green)

Pin No./Signal 9 Non Connect 10 Ground (Vert. sync.) 11 Sense 0 12 Sense 1 13 Horiz. sync 14 Vert. sync 15 Reserved

8 Ground (Blue)

These jacks will contain the audio information of the selected program source being viewed on the screen (Computer 1, Computer 2, Video 1 or Video 2). If you have selected program source Computer 2 the audio signal connected to the Computer 2 audio input jack will be available at the audio monitor output jacks. Use RCA type audio for connection.

• If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right and left jacks.

• If the audio input of the audio equipment is monaural, connect it to the left jack.

CONNECTING TO THE SERIAL PORT (DB 9-PIN) TERMINAL

If you control the. projector by computer, you must connect a cable (not provided) from your computer to this terminal.

CONNECTING TO THE USB PORT CONNECTORS (1 and 2)

This Projector is designed for connecting with USB Port of the computer or peripheral equipment that is to be standard.

CONNECTING AN IBM-COMPATIBLE DESKTOP

NOTE: When connecting the cable, the power cords of both the projector and the external equipment

should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

‘NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected

from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

NOTE: When connecting the cable, the power cords of both the projector and the external equipment

should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

NOTE: When connecting the cable, the power cords of both the projector and the external equipment

should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should

be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

CONNECTING TO THE VIDEO INPUT JACKS (1 and 2) BNC TYPE x 3

Connect to the video outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other AV equipment. Connect video output from AV equipment to these jacks using the BNC cables. The video input can be connected 3 types of signals; “COMPOSITE VIDEO”, “Y/C SEPARATE VIDEO” and COMPONENT VIDEO {Y, Cb (B-Y), Cr (R-Y)}. Set VIDEO SOURCE of each video input (VIDEO IN-1 or VIDEO IN-2) to input video matter. (Refer to “VIDEO SOURCE SELECT” operation on page 37).

CONNECTING S-VHS VIDEO INPUT JACKS (1 and 2)

The Video input includes an extra video input jack marked S-VIDEO to allow connection to an S-VHS format VCR that has separate Y/C video signals. The S-VIDEO jack has priority over the VIDEO jack.

CONNECTING TO THE AUDIO INPUT JACKS (1 and 2)

Connect to the audio outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other AV equipment. Use RCA type audio cable for connection.

• If the audio signal from the AV equipment is stereo, be sure to connect the right and left channels to the respective right and left audio input jacks.

• If the external audio signal is monaural, connect it to the left jack.

CONNECTING TO THE VIDEO MONITOR OUTPUT JAOKS (BNC TYPE x 3 )

These jacks will contain the video information of the selected program source being viewed on the screen (Video 1 or Video 2). If you have selected program source Video 2 the video signal connected to the Video 2 video input jack will be available at the video monitor output jacks. If you select program source “Computer 1” or “Computer 2, the video signal connected to the Video 1 video input jack will be available at the video monitor output jacks. Use BNC cable for connection.

CONNECTING TO THE S-VHS VIDEO MONITOR OUTPUT JACK•

The Video monitor output includes an extra video input jack marked S-VIDEO to allow connection to an S-VHS format VCR that has separate Y/C video signals. The S-VIDEO jack has priority over the VIDEO jack.

CONNECTING TO THE AUDIO MONITOR OUTPUT JACKS

These jacks will contain the audio information of the selected program source being viewed on the screen (Video 1 or Video 2). If you have selected program source Video 2 the audio signal connected to the Video 2 audio input jack will be available at the audio monitor output jacks. If you select program source “Computer 1” or “Computer 2”, the audio signal connected to the Video 1 audio input jack will be available at the audio monitor output jacks. Use RCA type audio cable for connection.

If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right and left jacks. If the audio input of the audio equipment is monaural, connect it to the left jack.

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector on before the peripheral equipment is switched on.

LAMP REPLACEMENT INDICATOR

Light is orange when the Lamp life draws to an end.

. TEMPERATURE WARNING INDICATOR

Flashes red when internal projector temperature is too high.

READY INDICATOR

Light is green when projector lamp is ready to be turned on.

LAMP POWER INDICATOR

Light is dim when the projector is on.

Light is brightened when the projector is in stand-by mode.

. VOLUME BUTTONS

Used to adjust volume.

. ZOOM BUTTONS

Used to operate power zoom lens.

. FOCUS BUTTONS

Used to operate power focus system.

LENS SHIFT BUTTONS

Used to operate power lens shift.

POWER ON/OFF BUTTON

Used to turn the projector on or off.

. MODE BUTTON

Used to select source.

(Computer 1, Computer 2, Video 1 or Video 2 Input)

AUTO IMAGE BUTTON

11.

Use this button, the POINT UP/DOWN/LEFT/RIGHT buttons and the SELECT button to make adjustments to the projector’s setting in MENU operation.

13.

(UP, DOWN, LEFT or RIGHT).

15.

Used to operate the AUTO IMAGE function.

. MENU BUTTON

This button will activate the MENU operation.

NORMAL BUTTON

Used to reset to normal picture adjustment preset by factory.

. POINT UP/DOWN/LEFT/RIGHT BUTTONS

To select an item on the MENU that you want to adjust. To select an item, move the arrow by pressing these buttons

SELECT BUTTON

This button has different functions depending on when used. This button is used to execute the item selected, to increase or decrease the values in certain items such as CONTRAST or BRIGHTNESS.

This remote control unit is not only able to operate the projector but also usable as a wireless mouse for a PC. One pointing pad and two click buttons are used for wireless mouse operation. Wireless mouse is usable when PC mouse pointer is displayed on the screen. When the menu or indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot be used.

NOTE: To use the unit as a PC wireless mouse,

connect the projector to the PC with the attached cable. Signals from the projector are transmitted to the PC, enabling the remote control unit of the projector to be used as a PC wireless mouse. (Refer to “CONNECTING THE PROJECTOR” in pages 14to 19 for the connection.)

LASER POINTER button

This remote control emits a laser beam light as the Laser Pointer from the Laser Light Window. When the LASER POINTER button is pressed, laser light goes on: when the button is released, light goes off. Laser light is emitted with the RED light which tells the laser beam being emitted. The laser emitted is a class II laser; therefore, do not look into the laser light window or shine the laser beam on yourself or other people. The three marks to the right are the caution labels for the laser beam. CAUTION-use of controls or adjustments or performance of procedures other than those specified herein-may result hazardous radiation exposure.

COMPUTER SELECT BUTTON

Used to select computer mode. (Computer 1 or Computer 2 Input)

VIDEO SELECT BUTTON

Used to select video mode. (Video 1 or Video 2 Input)

POWER ON/OFF BUTTON

Used to turn the projector on or oft.

VOLUME BUTTONS

Used to adjust volume.

.ZOOM BUTTON

Used to select power zoom lens adjust.

P-TIMER BUTTON

Used to operate the P-TIMER function.

FOCUS BUTTON

Used to select focus adjust.

FREEZE/NO SHOW BUTTON

Used to freeze on-screen image or change the screen into black image.

SOUND MUTE BUTTON

Used to mute sound.

LENS SHIFT BUTTON

10.

11.

12.

13.

14.

15.

To select an item on the MENU that you want to adjust. To select an item, move the arrow by pressing the pad upward, downward, leftward or rightward. Used to operate power zoom lens, power focus system or power lens shift by pressing the pad either upward or downward.

When in use as a wireless mouse

Used to move the pointer. The pointer is moved according to the direction you are pressing.

16.

17.

Used to compress the image in D.ZOOM mode.

When in use as a wireless mouse

This button has the same function as the right button in a PC mouse.

18.

19.

This button has different functions depending on when used. This button is used to execute the item selected, to increase or decrease the values in certain items such as CONTRAST or BRIGHTNESS.

When in use as a wireless mouse

This button has the same function as the left button in a PC mouse.

Used to select power lens shift.

CURSOR BUTTON

Used to display CURSOR on the screen.

AUTO IMAGE BUTTON

Used to operate the AUTO IMAGE function.

MENU BUTTON

This button will activate the MENU operation. Use this button, the POINT UP/DOWN/LEFT/RIGHT button and the SELECT (REAR CLICK) button to make adjustments to the projector’s setting in MENU operation.

NORMAL BUTTON

Use to reset to normal picture adjustment preset by factory.

POINTING PAD (POINT UP/DOWWLEFT/RIGHT BUTTON)

When in use as a remote for the projector

LASER BUTTON

When this button is pressed, laser light goes on; when the button is released, light goes off.

FRONT CLICK BUTTON

When in use as a remote for the projector

DIGITAL ZOOM BUTTON

Used to select digital zoom function.

SELECT (REAR CLICK) BUTTON

When in use as a remote for the projector.

Point the remote control toward the projector (Receiver window) whenever pressing the buttons.

Maximum operating range for the remote control is about 16.4’ (5m) and 60

front and rear of the

projector.

To insure safe operation, please observe the following precautions:

• Use (2) AA type alkaline batteries.

• Change two batteries at the same time.

• Do not use a new battery with a used battery.

• Avoid contact with water.

• Do not drop the remote control unit.

• If batteries have leaked on the remote control,

carefully wipe the case clean and load new batteries.

WIRED REMOTE JACK

When using the wired remote control, connect the remote cable to this jack.

COMPUTER SELECT BUTTON

Used to select computer mode. (Computer 1 or Computer 2 Input)

VIDEO SELECT BUTTON

Used to select video mode. (Video 1 or Video 2 Input)

POWER ON/OFF BUTTON

Used to turn projector on or off.

VOLUME BUTTONS

Used to adjust volume.

ZOOM BUTTONS

Used to operate power zoom lens.

FOCUS BUTTONS

Used to operate power focus system.

SOUND MUTE BUTTON

Used to mute sound.

LENS SHIFT BUTTONS

Used to operate power lens shift.

P-TIMER BUTTON

10.

11.

12.

projector’s setting in MENU operation.

13.

(UP, DOWN, LEFT or RIGHT).

14.

15.

16.

17.

Used to operate the P-TIMER function.

AUTO IMAGE BUTTON

Used to operate the AUTO IMAGE function.

MENU BUTTON

This button will activate the MENU operation. Use this button, the POINT UP/DOWN/LEFT/RIGHT buttons and the SELECT button to make adjustments to the

POINT UP/DOWN/LEFT/RIGHT BUTTONS

To selectan item on the MENU that you want to adjust. To select an item, move the arrow by pressing these buttons

FREEZE/NO SHOW BUTTON

Used to freeze on-screen image or change the screen into black image.

SELECT BUTTON

This button has different functions depending on when used. This button is used to execute the item selected, to increase or decrease the values in certain items such as CONTRAST or BRIGHTNESS.

DIGITAL ZOOM BUTTON

Use to select digital zoom function.

NORMAL BUTTON

Used to reset to normal picture adjustment preset by factory.

The remote control unit can be used as wireless or wired remote control.

Point the remote control toward the projector (Receiver window) whenever pressing the buttons. Maximum operating range for the remote control is about 16.4’ (5m) and 60° front and rear of the projector

Connect a remote control cable to R/C jacks located on the wireless/wired remote control unit and the side of the projector.

To insure safe operation, please observe the following precautions:

• Use (2) AA type alkaline batteries.

• Change two batteries at the same time.

• Do not use a new battery with a used battery.

• Avoid contact with water.

• Do not drop the remote control unit.

• If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.

The projector has two types of operation: DIRECT OPERATION and MENU OPERATION. DIRECT OPERATION allows you to operate the projector by using one button without showing the MENU. In MENU OPERATION mode, you display menus where you can adjust the projector’s settings. Follow the instruction for each control.

DIRECT OPERATION

ADJUST ITEM TOP CONTROL OF

THE PROJECTOR

POWER ON/OFF MODE SELECT SOUND VOLUME SOUND MUTE OOM

FOCUS

LENS SHIFT

DIGITAL ZOOM

NORMAL PICTURE FREEZE PICTURE NO SHOW P-TIMER AUTO IMAGE CURSOR

POWER ON-OFF POWER ON-OFF POWER ON-OFF MODE COMPUTER VIDEO COMPUTER VIDEO VOLUME (+) and (-) VOLUME (+) and (-) VOLUME (+) and (-) NOT AVAILABLE MUTE MUTE ZOOM (S) and (T) ZOOM (S) and (T) ZOOM

FOCUS (S) and (T) FOCUS (S) and (T) FOCUS

LENS SHIFT (S) and (T) NOT AVAILABLE D. ZOOM

NORMAL NORMAL NORMAL NOT AVAILABLE FREEZE NO/SHOW FREEZE/NO SHOW NOT AVAILABLE FREEZE/NO SHOW FREEZE/NO SHOW NOT AVAILABLE P-TIMER P-TIMER AUTO IMAGE AUTO IMAGE AUTO IMAGE NOT AVAILABLE NOT AVAILABLE CURSOR

WIRELESS/WIRED REMOTE CONTROL

LENS SHIFT (S) and (T) LENS SHIFT

SELECT POINT (UP/DOWN/LEFT/RIGHT)

WIRELESS REMOTE CONTROL

POINT (UP/DOWN)

POINT *UP/DOWN) D. ZOOM SELECT (REAR CLICK) FRONT CLICK POINT (UP/DOWN/LEFT/RIGHT)

MENU OPERATION

ADJUST ITEM TOP CONTROL OF

THE PROJECTOR

MODE SELECT

1. COMPUTER/VIDEO MODE

ADJUST ITEM TOP CONTROL OF

SOUND SOUND VOLUME TREBLE BASS BUIT-IN SP. SOUND MUTE LANGUAGE

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

THE PROJECTOR

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

WIRELESS/WIRED REMOTE CONTROL

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

WIRELESS/WIRED REMOTE CONTROL

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

WIRELESS REMOTE CONTROL

MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK)

WIRELESS REMOTE CONTROL

MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK)

SETTING

BLUE BACK DISPLAY REVERSE T/B

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

REVERSE R/L SPLIT WIPE POWER

MANAGEMENT

USB REMOTE

CONTROL

LAMP AGE

2. VIDEO MODE

ADJUST ITEM TOP CONTROL OF

THE PROJECTOR COLOR SYSTEM VIDEO SOURCE VIDEO Y,C Y, Cb, Cr PICTURE IMAGE COLOR TINT WHITE BALANCE CONTRAST BRIGHTNESS SHARPNESS PICTURE SCREEN WIDE REGULAR

POINT LEFT/RIGHT

SELECT

POINT UP/DOWN

SELECT

POINT LEFT/RIGHT

SELECT

POINT UP/DOWN

SELECT

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

WIRELESS/WIRED REMOTE CONTROL

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT(UP/DOWN) SELECT (REAR CLICK)

WIRELESS REMOTE CONTROL

MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK)

3. COMPUTER MODE

ADJUST ITEM TOP CONTROL OF

THE PROJECTOR COMPUTER SYSTEM

AUTO IMAGE FINE SYNC TOTAL DOTS POSITION PICTURE IMAGE FINE SYNC TOTAL DOTS WHITE BALANCE

POINT LEFT/RIGHT

SELECT

POINT UP/DOWN

SELECT

POINT LEFT/RIGHT

SELECT

POINT UP/DOWN

SELECT

POINT LEFT/RIGHT

SELECT

POINT UP/DOWN

SELECT

CONTRAST BRIGHTNESS SHARPNESS PICTURE POSITION

PC ADJUSTMENT

PICTURE SCREEN TRUE DIGITAL ZOOM

POINT LEFT/RIGHT

SELECT

POINT UP/DOWN

SELECT

POINT LEFT/RIGHT

SELECT

POINT UP/DOWN

SELECT

POINT LEFT/RIGHT

SELECT

POINT UP/DOWN

SELECT

POINT

LEFT/RIGHT/UP/DOWN

WIRELESS/WIRED REMOTE CONTROL

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT

MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT POINT LEFT/RIGHT/UP/DOWN

WIRELESS REMOTE CONTROL

MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK) MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK)

MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK)

MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK) MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK) MENU POINT (LEFT/RIGHT) SELECT (REAR CLICK) POINT (UP/DOWN) SELECT (REAR CLICK) FRONT CLICK POINT (LEFT/RIGHT/UP/DOWN)

NOTES:

1. The MENU, once activated, will not disappear unless you choose MENU QUIT. If you switch to DIRECT operation by pressing a DIRECT operation button while in MENU mode, the menus will disappear and the MENU operation will end.

2. You can use the REMOTE CONTROL UNIT or the TOP CONTROL OF THE PROJECTOR to operate the MENU operation.

- - -

Connect the projector to a source (Computer, VCR, Video Camera, Video Disc Player, etc.) using the appropriate

21).

terminals on the side of the projector (See “CONNECTING THE PROJECTOR” section on pages 10-

Connect the projector’s AC power cord into a wall outlet and turn the MAIN ON/OFF switch (located on the side of the projector) to the ON position. The LAMP POWER indicator will light RED, the READY indicator will light

GREEN.

Press the POWER ON/OFF button on the remote control unit or on the projector to ON. The LAMP POWER indicator light will dim and the cooling fans will operate. The wait display appears on the screen and the count-down starts (30-29-28-...1). The signal from the source appears after 30 seconds.

CAUTION: TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU HAVE TURNED IT ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

NOTE: TEMPERATURE WARNING INDICATOR flashes red, the projector will automatically turn off.

Wait at least 5 minutes before turning the projector. If the TEMPERATURE WARNING INDICATOR continued to flash, follow the procedures below:

(1). Press POWER ON/OFF button to OFF. (2). Check the air filter for dust accumulation.

(3). Remove dust with vacuum cleaner (See ‘AIR FILTER CARE AND CLEANING’ section on page 53.)

(4). Press POWER ON/OFF button to ON.

If the TEMPERATURE WARNING INDICATOR still continues to flash, call your authorized dealer or service station.

on the projector. The “Power off ?“ appears on the screen. Press again the POWER ON/OFF button to turn OFF the projector. The LAMP POWER indicator will light bright and READY indicator will turn off. The cooling fans will operate for 90 seconds after the projector is turned off. (During this “cooling down” period, the projector cannot be turned on.) The READY indicator will light green- again and the projector may be turned on by pressing the POWER ON/OFF button. To power down completely, turn the MAIN ON/OFF switch (located on the side of the projector) to the OFF position.

Press the POWER ON/OFF button on the remote control unit or

Press the MODE button on the projector or the COMPUTER and VIDEO button on the remote control unit to select Computer 1, Computer 2, Video 1 or Video 2 Input. The “Computer 1”, “Computer 2”, “Video 1” or “Video

2” display will appear on the screen for

a few

seconds.

Press the VOLUME buttons on the projector or on the remote control unit to adjust the volume. The volume display will be displayed on the screen for a few seconds. Pressing volume (+) will increase volume and increase the number on the screen.

Pressing volume (-) will decrease volume and decrease the number on the

screen.

Pressing the MUTE button on the remote control unit will mute audio. Press the MUTE button again to restore audio to its previous level. The mute display will be displayed on the screen for afew seconds.

Use Top control and Wireless/Wired remote control unit.

Press the ZOOM (S) or (S) button to obtain your desired picture size. For a larger picture, press (S) and for a smaller picture, press (T).

Use Wireless remote control unit.

Press the ZOOM button and press POINT UP/DOWN button(s) to obtain your desired picture size. The Zoom display will be displayed on the screen for a few seconds. For a larger picture, press (UP) and for a smaller picture, press (DOWN).

Top control and Wireless/Wired remote control unit.

Use

Press the FOCUS (S) or (T) button for a sharper, crisper picture.

Use Wireless remote control unit.

Press the FOCUS button and press POINT UP/DOWN button(s) to obtain a sharper, crisper picture. The Focus display will be displayed on the screen for a few seconds.

Use Top control and Wireless/Wired remote control unit.

Press the LENS SHIFT (S) or (T) button to obtain your desired screen position.

Use Wireless remote control unit.

Press the LENS SHIFT button and press POINT UP/DOWN button(s) to obtain your desired screen position. The Lens shift display will be displayed on the

screen for a few seconds.

Press the D. ZOOM button on the wireless remote control unit. The “D.zoom” and the magnifying-glass icon is displayed to indicate Digital zoom mode. Digital zoom mode can be adjust the image size or pan the image. To expand the image size, press SELECT (REAR CLICK) button. The image is magnified by degrees (Expand function). To compress the image size, press FRONT CLICK button. The size of image is reduced by degrees (Compress function). To pan the image, press POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) button(s). The image move to the direction indicated (Panning function) See the page 49 for more detail.

The normal picture image level is factory preset on the projector and can be restored anytime by pressing the NORMAL button on the projector or on the remote control unit. The “Normal’ display will be displayed on the screen for a few seconds.

Press the FREEZE/NO SHOW button on the remote control unit, and the picture will remain on-screen. This function is cancelled when the FREEZE/NO SHOW button is pressed again or any other button is pressed.

NOTE: Your computer or video equipment is not affected by this function, and will continue to run.

Press the FREEZE/NO SHOW button (on the remote control unit) is twice. The screen will change into black image and the- “NO SHOW” is displayed on the

screen for a few seconds. This function is cancelled when the FREEZE/NO SHOW button is pressed again or any other function button is pressed.

Press the P-TIMER button on the remote control unit. The timer display “00:00”

appears on the screen and the timer starts to count the time (00:00 to 59:59). Press

again the P-TIMER button to stop the timer. Then press the P-TIMER button to

cancel the P-TIMER function.

Press the AUTO IMAGE button on the projector or on the remote control unit. The item(s) indicated “ON” in the

AUTO

IMAGE FUNCTION are adjusted automatically.

If all the items in AUTO IMAGE FUNCTION are “OFF”, AUTO IMAGE SETTING display appears. If you wish to

operate the AUTO IMAGE FUNCTION, perform the steps 3 - 9 of “AUTO

IMAGE FUNCTION” section on page 42.

Press the CURSOR button on the wireless remote control unit. The CURSOR

is displayed on the screen. Press POINT UP/DOWN/LEFT/RIGHT (POINTING

PAD) button(s) to control CURSOR. The CURSOR is moved according to the

direction you are pressing. Press CURSOR button again, and CURSOR disappears.

You can select a mode from MAIN MENU display among computer 1, computer 2, video 1, video 2.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select Computer or Video and press the SELECT (REAR CLICK) BUTTON. Another dialog box MODE DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to the mode you want (computer 1, computer 2, video 1 or video 2) to use by pressing the POINT

UP/DOWN BUTTON(s) and then press the SELECT (REAR CLICK) BUTTON.

You can adjust the sound volume, treble, bass levels and Built-in SP., Sound Mute ON/OFF switch in the MENU display.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select SOUND and press the SELECT (REAR CLICK) BUTTON. Another dialog box SOUND ADJUST DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

5. To increase the sound volume, treble and bass, point the arrow to A and then press the SELECT (REAR CLICK) BUTTON. To decrease the sound volume, treble and bass, point the arrow to V and then press the SELECT (REAR CLICK) BUTTON.

6. To disconnect the built-in speaker, point the arrow to Built-in SP. and then press the SELECT (REAR CLICK) BUTTON. The display

7. To mute the sound, point the arrow to Mute and then press the SELECT (REAR CLICK) BUTTON. The display is changed On and mute the sound.

8. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON.

is changed Off and Internal speaker is disconnected.

A language Japanese.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select LANGUAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box LANGUAGE SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to the language you want to use by pressing the POINT UP/DOWN BUTTON(s) and then press the SELECT (REAR CLICK) BUTTON.

in the MENU display can be selected among English, German, French, Italian, Spanish and

This projector is compatible with the six major broadcast video standards: PAL, SECAM, NTSC, NTSC 4.43, PALM and PAL-N (COLOR SYSTEMs). When the color system

systems (PAL, SECAM, NTSC or NTSC 4.43) automatically. However, if the video signal is not strong

of 4 enough to detect the video format, the projector may not reproduce the proper video image. In case this happens, this projector allows you to choose a

specific broadcast signal format.

is set to “Auto position”, this projector can detect one

1. Connect the video equipment to the PROJECTOR and turn the projector on first. -

2. Set MODE SELECT to “VIDEO MODE”.

3. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

4. Press the POINT LEFT/RIGHT BUTTON(s) to select SYSTEM and press the SELECT (REAR CLICK) BUTTON. displayed in the system window.

5. Press the POINT DOWN BUTTON and a red arrow will appear. -

5. To change the current COLOR SYSTEM, press the POINT UP/DOWN BUTTON(s) to move the arrow to a desirable system and then press the SELECT (REAR CLICK) BUTTON.

Another dialog box COLOR SYSTEM DISPLAY will appear. The current COLOR SYSTEM is

7. The setting changed remains effective until the MAIN ON/OFF switch is turned off.

1. Connect the video equipment to the PROJECTOR and turn the projector on first.

2. Set MODE SELECT to “VIDEO MODE”.

3. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

4. Press the POINT LEFT/RIGHT BUTTON(s) to select VIDEO SOURCE and press -the SELECT (REAR CLICK) BUTTON. Another dialog box VIDEO SOURCE DISPLAY will appear. The current VIDEO SOURCE is displayed in the window.

5. Press the POINT DOWN BUTTON and a red arrow will appear.

6. To change the current VIDEO SOURCE, press the POINT UP/DOWN BUTTON(s) to move the arrow to a desirable video source and then press the SELECT (REAR CLICK) BUTTON.

7. The setting changed remains effective until the MAIN ON/OFF switch is turned oft.

Picture adjustments have been preset at the factory. If you want to change the setting, operate the projector as

follows.

1. Press MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings.

3. In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers. The items and the range of the levels that you can adjust are summarized in the table below.

4. Press the POINT DOWN BUTTON and a red arrow will appear.

5. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

6. To increase the level, point the arrow to A and then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to V and then press the SELECT (REAR CLICK) BUTTON.

7. You may want to store the settings

in the memory so that you can recall them later. To store the settings, move

the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, “OK

?“ is displayed for confirmation.

8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are memorized even if the MAIN ON/OFF is switched off.

9. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

10.If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. The settings changed remains effective until the MAIN ON/OFF switch

is turned off.

11 .To recall the settings from the memory that you have stored, move the arrow to Reset and then press the

SELECT (REAR CLICK) BUTTON. When you have reset the settings, “OK

?“ is displayed for confirmation. Move

the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed.

NOTE: “TINT” will be skipped in the PAL, SECAM, PAL-M and PAL-N mode

This projector has the Wide function, which enables you to view a wider video image.

WIDE function This projector is able to project not only a normal video image (with 4 x

3 aspect ratio), but also a wider video

image by

compressing 4 x 3 image. This feature enable you to enjoy watching pictures like cinema images. You can switch either to WIDE or to REGULAR screen mode.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select SCREEN and press the SELECT (REAR CLICK) BUTTON.

Another dialog box SCREEN ADJUST DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear. -

4. To switch to “Wide” mode, move the arrow to Wide by pressing the POINT UP/DOWN BUTTON(s) and then press the SELECT (REAR CLICK) BUTTON.

5. To switch to “Regular” mode, move the arrow to Regular by pressing the POINT UP/DOWN BUTTON(s) and then press the SELECT (REAR CLICK) BUTTON.

This projector is adjustable to different types of computer display signals based on VGA, SVGA, XGA or SXGA (See “COMPATIBLE COMPUTER SPECIFICATIONS” on the next page). If you set MODE SELECT to “COMPUTER”, the projector will automatically process the incoming signal and project the proper image without any special setting. Although this will work in most cases, you may be required to manually set the projector for some computer signals. If the computer image is not reproduced properly, try the following procedure and switch to the computer display mode that you want to use.

1. Connect the COMPUTER to the PROJECTOR and turn the projector on first.

2. Set MODE SELECT to “COMPUTER MODE (1 or 2)”. This shows the current display mode initially detected by the projector in the system window. And “Current mode” display appears.

NOTE:1. If the projector cannot discriminate or detect the input signal from the computer, the “Go PC adj.” display

appears.

NOTE : 2. If no input signal from the computer, the “No signal” display appears.

NOTE: 3. If the incoming signal is digital, the “D-VGA”, “D-SVGA”, “D-XGA” or “D-SXGA” display appears.

3. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

4. Press the POINT LEFT/RIGHT BUTTON(s) to select SYSTEM and press the SELECT (REAR CLICK) BUTTON. Another

dialog box COMPUTER SYSTEM DISPLAY will appear.

5. Press the POINT DOWN BUTTON and a red arrow will appear.

6. If you want to change the current display mode, move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select one of the modes.

7. Press the SELECT (REAR CLICK) BUTTON to change the display mode.

8. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

- -

PC ADJUSTMENT

This is a special function that may be used when a computer image is not reproduced properly. (See the pages 45

-. 48 for more detail.)

Specifications are subject to change without notice. NOTE: Basically this projector can accept the signal from all computers with the above mentioned V, H-Frequency

and less than 200 MHz of Dot Clock.

The Auto image function is provided to automatically adjust Fine sync., Total dots and Screen position for

most computers.

NOTE: This auto image function will be skipped when the incoming signal is digital.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. -

2. Press the POINT LEFT/RIGHT BUTTON(s) to select AUTO IMAGE and press the SELECT (REAR CLICK) BUTTON.

Another dialog box AUTO IMAGE SETTING DISPLAY will appear. -

3. Press the POINT DOWN BUTTON and a red arrow will appear. -

4. Move the arrow to an item(s) you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

5. Change the setting “On” , press the SELECT (REAR CLICK) BUTTON.

6. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select “Go!” and then press the SELECT (REAR CLICK) BUTTON. The auto image function is started now. It will take about 10 seconds.

7. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, “OK?” is displayed for confirmation.

8. Move the arrow to “Yes” and then press the SELECT (REAR CLICK) BUTTON. The stored settings are memorized even

if the MAIN ON/OFF is switched oft.

9. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON.

10.This setting is temporarily effective until you turn

off the projector or change the input signal.

NOTE: The fine sync., total dots and screen position of some computers may not be fully adjusted with the “Auto

Image Function.” In that case, use the “Picture Image” and/or “Picture Position” adjustments (see pages 43

44) to make fine-adjust them after the “Auto Image Function” is executed.

- -

—

Picture adjustments have been preset at the factory. It you want to change the setting, operate th projector as

follows

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings.

3. In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers. The items and the range of the levels that you can adjust are summarized

in the table below.

4. Press the POINT DOWN BUTTON and a red arrow will appear.

5. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

6. To increase the level, point the arrow to A and then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to V and then press the SELECT (REAR CLICK) BUTTON.

7. You may want to store the settings in the memory so that you can recall them later. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, “OK

?“ is -displayed for confirmation.

8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are memorized even if the MAIN ON/OFF is switched oft.

9. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

10.If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK)

BUTTON. The settings changed remains effective until the MAIN ON/OFF

switch is turned off. -

11 .To recall the settings from the memory that you have stored, move the arrow to Reset and then press the

SELECT (REAR CLICK) BUTTON. When you have reset the settings, “OK

?“ is displayed for confirmation. Move

the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if

needed. -

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(S) to select POSITION and press the SELECT (REAR CLICK)

BUTTON.

Another dialog box POSITION SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to a desirable direction (Ã,Ä,Å,Æ) by pressing the POINT LEFT/RIGHT/UP/DOWN

BUTTON(s) and press the SELECT (REAR CLICK) BUTTON to a desirable picture position.

5. You may want to store the settings to the memory so that you can recall them later. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, “OK ?“ is displayed for confirmation.

6. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are memorized even if the MAIN ON/OFF is switched off.

7. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

8. If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. The settings changed remains effective until the MAIN ON/OFF switch is turned off.

9. To recall the settings from the memory that you have stored, move the arrow to Reset and then press the SELECT (REAR CLICK) BUTTON. When you have reset the settings, “OK ?“ is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed.

This projector can automatically detect most display signals from most personal computers currently distributed.

This function will be skipped when the incoming signal is digital. S

However, some computers adopt a special signal format which is different from the standard one and the projector

cannot detect it. If this happens, the projector cannot reproduce a proper image. And a flickering picture, a nonsynchronized picture, a non-centered picture or a skewed picture may be projected instead.

For those non-standard formats, this projector is provided with PC ADJUST, enabling you to precisely adjust several parameters to match with the input signal format. The projector has eight independent memory areas where you can store the parameter you have set. This enables you to recall the setting for a specific computer when you need it.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select PC ADJUST and press the SELECT (REAR CLICK)

BUTTON.

3. In this dialog box, you will select one of the memory areas from among “Mode 1” to “Mode 8”. If parameters-

have been previously set and stored in the memory, the status “Stored” will appear on the corresponding row. If not, “Free” will

4. Press the POINT DOWN BUTTON and a red arrow will appear.

5. Move the arrow to one of the “Modes” (Free position) where you want to store the parameters by pressing the

POINT UP/DOWN BUTTON(s). Press the SELECT (REAR CLICK) BUTTON to select it.

NOTE: If “Stored” appears in all Modes, no new PC parameter data can be stored. In this case, clear-the PC -

parameter data using Mode free Function.

Another dialog box “Where to reserve” will appear.

appear.

6. Another dialog box “PC ADJUSTMENT DISPLAY 1” will appear and the parameter data for the Mode you

have selected

7. The parameters will be filled with the data determined by the projector according to the present signal input.

8. The function of the parameters and their values are summarized in the table as below.

9. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

10.To increase the level, point the arrow to S and then press the SELECT (REAR CLICK) BUTTON. To decrease

the level, point the arrow to T and then press the SELECT (REAR CLICK) BUTTON.

11.If you want to store the settings in the memory, move the arrow to Stored and press the SELECT (REAR CLICK)

BUTTON. When you have stored the settings, “OK then press the SELECT (REAR CLICK) BUTTON.

12.To recall the parameter data before setting, move the arrow to Reset and then press the SELECT (REAR CLICK)

BUTTON. When you have reset the settings, “OK then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed.

13.To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

14.If you quit the MENU without storing the settings in the memory, the parameter data you changed will not be kept.

15.The stored settings are memorized even if the MAIN ON/OFF is switched oft. -

16.Adjust the data such as a “Clamp”, “Fine sync”, “Display area”, “Horiz. scale” and “Vert. scale” if needed, move

the arrow by pressing the POINT UP/DOWN BUTTON(s) to select (T). Press the SELECT (REAR CLICK) BUTTON.

is shown in this dialog box.

?“ -is displayed for confirmation. Move the arrow to Yes and

?“ is displayed for confirmation. Move the arrow to Yes and

ITEM FUNCTION

TOTAL LINES

The number of the total vertical lines. Adjust the number to match your PC image.

TOTAL DOTS HORIZONTAL

The number of the total dots in one horizontal period. Adjust the number to match your PC image. Adjustment of the horizontal picture position. When the image is not centered on the screen, adjust this.

VERTICAL

Adjustment of the vertical picture position. When the image is not centered on the screen, adjust

this.

17. Another dialog box “PC ADJUSTMENT DISPLAY 2” will appear and the parameter data for the Mode you have selected is shown in this dialog box.

p18. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

19. To increase the level, point the arrow to S and then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to T and then press the SELECT (REAR CLICK) BUTTON.

20. If you want to store the settings in the memory, move the arrow to Stored and press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, “OK ?“ is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON.

21. To recall the parameter data before setting, move the arrow to Reset and then press the SELECT (REAR CLICK) BUTTON. When you have reset the settings, “OK ?“ is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed.

22. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

23. If you quit the MENU without storing the settings in the memory, the parameter data you changed will not bekept.

24. The stored settings are memorized even if the MAIN ON/OFF is switched off.

ITEM FUNCTION CLAMP Adjustment of the clamp level. When the image has a dark bar, try this adjustment. FINE SYNC Adjust the picture as necessary to eliminate flicker from the display. DISPLAY AREA Adjustment the display area to match your PC. HORIZ. SCALE Expanding or compressing level for the horizontal direction. VERT. SCALE Expanding or compressing level for the vertical direction.

MODE FREE

The Mode free function is provided to confirm or clear the parameter data produced by PC ADJUST.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select PC ADJUST and press the SELECT (REAR CLICK) BUTTON.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to one of the “Modes” (Stored position) that you want to confirm by pressing the POINT UP/DOWN BUTTON(s). Press the SELECT (REAR CLICK) BUTTON. Another dialog box “PC ADJUSTMENT DISPLAY” will

5. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON.

6. To modify the parameter data, perform the steps 9

7. To clear the parameter data, move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select Mode free. Press the SELECT (REAR CLICK) BUTTON. “OK?” is displayed for confirmation.

8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON to clear the parameter data.

9. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

Another dialog box “Where to reserve” will appear.

appear.

- 24 of PC ADJUSTMENT SECTION.

This projector can adjust the image size and pan the image with PICTURE SCREEN ADJUSTMENT.

1. Press MENU BUTTON and MAIN MENU DISPLAY dialog box will appear.

2. Press POINT LEFT/RIGHT BUTTON(s) to select SCREEN and press the SELECT (REAR CLICK) BUTTON.

Another dialog box SCREEN ADJUST DISPLAY will appear.

3. Press POINT DOWN BUTTON and a red arrow will appear.

4. To adjust the image size or pan the image, move the arrow to Digital zoom

pressin9 POINT UP/DOWN BUTTON(s) and then press SELECT

(REAR CLICK) BUTTON. MAIN MENU DISPLAY and SCREEN ADJUST DISPLAY will

disappear. The “D.zoom” and the magnifying-glass icon is

displayed to indicate Digital zoom mode.

5. Move the magnifying-glass icon by pressing the POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) BUTTON(s).

6. To expand the image, press SELECT (REAR CLICK) BUTTON. The image is magnified by degrees (Expand

function).

7. To compress the image size, press FRONT CLICK button on the remote control.The size of image is reducedby

degrees (Compress function).

8. To pan the image, press POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) BUTTON(s) and move the

magnifying-glass icon.

9. To cancel the Digital Zoom mode, press other buttons (Except NORMAL and CURSOR BUTTONS). - -

10. Press the NORMAL BUTTON in Digital zoom mode, the image size changed to the screen size (1024 x 768).

11. Press the CURSOR BUTTON in Digital zoom mode, the magnifying-glass icon is disappears on the screen.

However, the Digital Zoom mode is held.

12. To turn the image size to true size (1024 x 768 in XGA or SXGA, 800 x 600

in SVGA and 640 x 480 in VGA),

move the arrow to True by pressing POINT UP/DOWN BUTTON(s) and then press SELECT (REAR CLICK) BUTTON. The image size is turned to the true size.

• This projector cannot display in the resolution more than 1280 x 1024. If your computer’s screen resolution

is higher than 1280 x 1024, reset the resolution to the lower.

• The image data of VGA (640 x 480), SVGA (800 x 600), or SXGA (1280 x 1024) is modified to fit the screen size in the initial mode.

• When the original image size is larger than the screen size (1024 x 768), this projector becomes Digital Zoom mode automatically.

• The maximum size in expand mode is 4 times as large as the original screen size. (When original image size is smaller than the screen size (1024 x 768).

• The minimum size in compress mode mode or 640 x 480 in VGA mode.

is the screen size (1024 x 768) in XGA or SXGA mode, 800 x 600 in SVGA

- -

• Panning function can work only when the image is expanded.

• The normal “Panning Operation” may not function properly if the computer system prepared with the “PC Adjust” is used.

Turn SPLIT WIPE function On in the SETTING menu. The picture will change into next one by sliding black image

When this function is in the “On” position, the left/right picture reverse capabilityTurn SPLIT WIPE function On in the SETTING menu. The picture will change into next one by sliding black image

is changed.

side ways when the input source

is changed.

This projector has other functions setting: Blue back, Display, Reverse T/B, Reverse R/L, Split wipe, Power management, USB, Remote control and Lamp age.

When this function is without video noise on the screen when the video source is unplugged or turned

in the “On” position, the projector will project a blue image

off.

When this function is in the “On” position, on-screen displays always appear when adjustments are made. Although these on-screen displays are very helpful, these may spoil the view To avoid this, you can keep back certain displays by switching that you can hide.

• Wait Display

• Mute Display • Zoom/Focus/Lens shift Display • D.Zoom Display

• Normal Display

• Mode Display • Volume Display

• No show Display

if adjustments are made during presentations.

this function “Off”. The followings are the displays

When this function is in the “On” position, the top/bottom-picture reverse.

When this function is in the “On” position, the left/right picture reverse capability lets you project onto a rear projection screen.

Turn SPLIT WIPE function On in the SETTING menu. The picture will change into next one by sliding black image side ways when the input source Change the input source by MODE button. The picture is replaced by black image from side ways to the center, and the next one appears from the center to side ways like drawing the black curtains.

Power management will be turn the projector Lamp off when the input signal is interrupted (Picture is not displayed) over 5 minutes. This aims at saving power and Lamp life. The Lamp is automatically turned on when the signal is input. To activate this function, turn the “Power management” in the SETTING menu “On”.

This Projector is designed for connecting with SUB Port of the computer or peripheral equipment that is to be standard. When this function is in the “ “ (Mouse) position, you control the pointer of the computer using the projector’s wireless remote control unit. When this function is in the “ “ (Control) position, you control the projector by computer.

is changed.

NOTE: Before you control the projector by computer, install USB driver )optionally saled parts) and set up the computer following instruction in the USB driver package. Contact your authorized dealer.

This projector can be operated with two different code, one is factory-set normal code (MODE 1) and the other one is extended code (MODE 2). This is used to prevent the remote control operation mixture (jam) when two projector and several remote control video equipments are system-up and used together.

When you change the code MODE 2, you must change both projector and Remote Control Unit.

To change Projector code:

Set REMOTE CONTROL in SETTING menu (below figure) to “MODE 2”.

To change Remote Control Unit code

Press both “MENU” and “NORMAL” button on the Remote Control Unit for over 10 seconds. After code changed, make sure the Remote Control operation is functioning properly. To go back to normal code (MODE 1), take same operation above.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK)

BUTTON. Another dialog box SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

‘4. Move the arrow to an item you want to set by pressing the POINT UP/DOWN BUTTON(s).

5. If you want to change the setting, press the SELECT (REAR CLICK) BUTTON.

6. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON.

7. The settings are memorized even if the MAIN ON/OFF is switched off.

The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the

lamp

replacement monitor timer by using this function.

NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp is replaced.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK) BUTTON.

Another dialog box SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select Lamp age and then press the SELECT (REAR CLICK) BUTTON. When you reset the lamp replace monitor, “lamp replace monitor reset?” is displayed for confirmation.

5. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON, “OK?”is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON, the lamp replace monitor is reset.

6. Move the arrow to No and then press the SELECT (REAR CLICK) BUTTON. The lamp replace monitor is not reset.

7. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

The TEMPERATURE WARNING INDICATOR flashes red when the internal temperature of the projector exceeds the normal temperature.

Possible causes for the temperature warning may be:

1. Ventilation slots of the projector are blocked. In such an event,

reposition

the projector so that ventilation slots are not obstructed.

2. Air filter is clogged with dust particles. Remove dust from the air

filter by following instructions in the Air Filter Care and Cleaning section

above. If the TEMPERATURE WARNING INDICATOR still continues to flash after checking (1) and (2), call your authorized dealer or service station.

The removable air filter prevents dust from accumulating on the surface of the projection lens and projection mirror. Should

the air filter become clogged with dust particles, it will reduce the cooling fan’s effectiveness and may result in internal heat build up and reduce the life

of the projector.

To clean the air filter, follow the cleaning procedures below:

Turn the POWER ON/OFF button OFF.

2. Remove the

3. Remove the air filter and sponge from the filter cover.

4. Clean the air filter with a vacuum cleaner.

air filter cover.

5. Replace the air filter and sponge. Make sure that air filter cover is

fully inserted.

Do not clean with water. Doing so may damage the air filter. Do not operate the projector with air filter removed.

TO ENJOY PICTURE IMAGE, USE THE PROJECTOR IN THE CLEAN ENVIRONMENT. USAGE IN THE CLEAN ENVIRONMENT IS RECOMMENDED.

When used under the dusty or smoky conditions, dust may accumulate on the

liquid crystal panel and lens inside

it, and may resultantly be projected on

the screen together with the picture. When the above symptoms are

noticed contact the place where your authorized dealer or service station for the cleaning.

WHEN THE PROJECTION LAMP OF THIS PROJECTOR DRAWS TO AN END, THE LAMP REPLACEMENT INDICATOR LIGHTS YELLOW AND THE WARNING MESSAGE “LAMP REPLACEMENT” APPEARS AS THE RIGHT FIGURE. WHEN THE WARNING MESSAGE IS DISPLAYED, THE PROJECTION LAMP SHOULD BE REPLACED.

To terminate the warning message

Replace the Projection Lamp and reset the LAMP REPLACEMENT MONITOR

TIMER (See “LAMP AGE” section on page 52.), and the warning message is terminated.

To erase the warning message in a moment.

To erase the warning message for a moment, move the arrow to “YES” by pressing the POINT UP/DOWN BUTTON(s) and then press the SELECT (REAR CLICK) BUTTON. This procedure is temporary measure, and the warning massage appears again when the projector is turned on next time.

• For continued safety, replace with a lamp assembly of the same type.

• Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

• Do not drop the lamp module or touch the glass bulb The glass can shatter and cause injury.

Follow these steps to replace the lamp assembly.

1. Turn off the projector and allow the projector to cool thoroughly.

2. Disconnect the AC cord from the projector.

3. Remove 2 screws with a screwdriver and remove the lamp cover.

4. Remove 2 screws with a screwdriver and pull out the lamp assembly by

grasping the handle.

5. Replace the lamp assembly.

6. Tighten 4 screws to secure the lamp cover to the lamp assembly.

7. Connect the detachable AC cord to the projector.

8. Reset the lamp replacement monitor timer.

(See “LAMP AGE” section on page 52.)

NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except

after the lamp is replaced.

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering the Lamp, give the following information to the dealer.

• Model No. of your projector : LC-X2U/X2UL

• Replacement Lamp Type No. : POA-LMP2OJ (Service Parts No. 610 280 4225) -

Follow these steps to clean the projection lens:

1. Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of

cleaner.

Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2. Lightly wipe the cleaning cloth over the lens.

3. When you don’t use the projector, replace the lens cover.

Before calling your dealer or service station for assistance, check the matters below once again.

1. Make sure you have connected the projector to your equipment as described in section “CONNECTING THE PROJECTOR” on pages 14- 21.

- - -

2. Check cable connections. Verify that all computer, video and power cords are properly connected.

3. Verify that power is switched on. -

4. If the projector still does not display an image, re-start the computer.

5. If the image still does not display, unplug the projector from the computer and check the computer

monitor’s display. The problem may be with your graphics controller rather than with the projector. (When you

reconnect the projector, remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in order of:

Projector and computer)

6. If the problem still exists, check the following chart.

Problem: Try these Solutions:

No power

• Plug the projector into an AC outlet. -

•Turn the MAIN ON/OFF switch to ON.

•Press the POWER ON/OFF switch to ON.

•Be sure the READY INDICATOR light is ON.

•Wait 90 seconds after the projector is turned OFF before turning the projector back on.

NOTE: After pressing the POWER ON/OFF button to OFF. The projector functions

as indicated.

1.The LAMP POWER indicator will light and the READY indicator will turn-off. -

2.After 90 seconds, the READY indicator will light green again and the projector may be turned on by pressing the POWER ON/OFF button.

•Check temperature warning indicator. If the indicator flashes red, the projector cannot be turned on.

(See “BASIC OPERATION” section on page 32).

•Check the projection lamp.

Image is out of focus

•Replace the lamp cover. (Check the interlock switch inside of the lamp cover.) ~ Adjust the focus.

• Make

sure the projection screen is at least 4.9’ (1.5 m) from the projector.

• Check the projection lens to see if it needs cleaning.

NOTE:: Moving the projector from a cool temperature location to a warm temperature location may result

in moisture condensation on the lens. In

such an event, leave the projector OFF and wait until condensation disappears.

Problem: Try these Solutions:

Picture is T/B inverted, Picture is L/R Reversed. Some displays are not seen during the operations No sound.

Remote control unit doesn’t work.

Wireless mouse function does not work.

Check Reverse T/B feature.

(See “OTHER FUNCTION SETTING” section on pages 50

Check Reverse L/R feature. (See “OTHER FUNCTION SETTING” section on pages 50 51).

Check Display feature. (See “OTHER FUNCTION SETTING” section on pages 50 51).

• Check audio cable connection from audio input source.

• Adjust audio source.

• Press the VOLUME (+) button.

• Press the MUTE button.

• Check the batteries.

• Make sure nothing is blocking between the remote control sensor and remote

control unit. S

• Make sure you are not too far from the projector when using the remote controlunit.

{Maximum operate range 16.4(5 m)}.

• Check the transmitted signal mode from the remote control unit.

(See “OTHER FUNCTION SETTING” section on pages 50 — 51).

• Check the cable connection between the projector-and the computer.

• Check the mouse setting on your computer. -

• Turn on the projector before you turn on the computer.

Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Number of Pixels

Color System 6 color system (PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N) Scanning Frequency H-sync. 15 100 KHz, V-sync. 50 — 100 Hz Projection Image Size (Diagonal) Adjustable from 40” to 600” Horizontal Resolution 800 TV lines Projection Lens F2.0 ~ 2.3 lens with f=75.7 mm - 97.5 mm Motor zoom and focus Motorized Lens Shift ± 760 mm on 100” screen Throw Distance 4.9’ (1.5 m) 80.7’ (24.6 m) Projection Lamp 440 watt type AV Input Jacks BNC Type {Video/Y, C/Cb (B-Y), Cr (R-Y)} x 2 sets

Video Monitor Output Jack BNC Type (Video/Y, C/Cb (B-Y),Cr (R-Y)} x 1 set

Audio Monitor 0utput Jacks RCA Type (R and L) x 1 set RCA Type (R and L) x 1 set Computer Input 1 Jack MDR 20-pin Terminal (Digital), HDB ‘15-pin Terminal (Analog), Multi-pole 12-pin

Computer Input 2 Jack BNC Type (R, G, B, H and V), Multi-pole 12-pin (Control port) and USB port Computer Audio Input Jack RCA Type (A and L) x 2 sets Computer Output Jack HDB 15-pin Terminal Computer Audio Output Jack RCA Type (R and L) x 1 set Other Jack Wired Remote Jack and Serial port (DB 9) Built-in Speaker (2) 5 cm x 9 cm, Stereo (R and L), 3 watt (Music Power) Image Elevation Adjustment Up to 4° Wattage 100 — 120 V AC, 50/60 Hz Power Consumption 7.8 A (Max. Ampere) Operating Temperature 5°C - 35°C Storage Temperature —10°C — 60°C Remote Control Transmitters

This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards.

Multi-media Projector

15.4” (390 mm) x 9.2” (234 mm) x 22.9” (582 mm)

39.2 lbs (17.8 kg)

1.8” TFT Active Matrix type x 3 panels 2,359,296 {786,432 (1,024 x 768) x 3}

RCA Type (Audio A and L) x -2 sets and DIN 4 pin (S-Video) x 2 sets

and DIN 4 pin (S-Video) x 1 set

(Control port) and USB port

Wireless Remote Control with Laser Beam (Class II Laser) Max. Output 1 mW/Wave Length 660 ± 2Onm, batteries (2) AA type. Wireless/Wired Remote Control, batteries (2) AA type.

Audio Visual/Video Products

EIKI INTERNATIONAL, INC.

26794 Vista Terrace Drive, Lake Forest,

TEL (949) 457-0200 FAX (949) 457-7878

IN CANADA, EIKI CANADA

865 Heritage Drive P.O. Box 156

Midland Ontario L4R 4K8 Canada

TEL

(705) 527-4084 FAX (705) 527-4087

Printed in Japan Part No. 610 280 7554 (1AA6P1 P1 950-- ME6B)

CA. 92630-8113, U.S.A.

Eiki LC-X2U, LC-X2UL User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

MODEL LC-X2U

SAFETY PRECAUTIONS

TABLE OF CONTENTS

FEATURES AND DESIGN

INTRODUCTION

COMPATIBILITY

IMAGE RESOLUTION

AUTOMATIC MULTISCANNING SYSTEM

SCREEN MODE

MULTILANGUAGE

UNPACKING THE PROJECTOR

TRADEMARKS

DIRECT OPERATION

MENU OPERATION