Eiki EIP-250, EIP-2600 User Manual
®
EIP-2600
EIP-250
Introduction Quick Start Setup
Connections
OWNER’S MANUAL
EIKI INDUSTRIAL CO., LTD.
EIP-2600
Appendix
IMPORTANT
• For your assistance in reporting the loss or theft of your
Projector, please record the Model and Serial Number
located on the bottom of the projector and retain this
information.
• Before recycling the packaging, please ensure that you
have checked the contents of the carton thoroughly against
the list of “Supplied accessories” on page 10.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A
fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or
and of the same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied,
cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and
disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a
serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
•
marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N
•
or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
•
coloured red.
Model No.:
Serial No.:
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian
and Portuguese. Carefully read through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch,
Italienisch und Portugiesisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors
sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français,
espagnol, italien et portugais. Veuillez lire attentivement ces instructions avant de faire fonctionner le
projecteur.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, español,
italiano y portugués. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo, italiano
e portoghese. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Espanhol, Italiano e
Português. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.
ii
Before using the projector, please read this owner’s manual carefully.
Introduction
ENGLISH
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification,
or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act,
PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount
of mercury. Disposal of these materials may be regulated due to
environmental considerations. For disposal or recycling information,
please contact your local authorities, the Electronics Industries Alliance:
www.eiae.org, the lamp recycling organization www.lamprecycle.org,
or 1-800-242-3454.
U.S.A. ONLY
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 52.
Authorized representative responsible for the European Union Community Market
EIKI Deutschland GmbH
Am Frauwald 12, 65510 Idstein
E.U. ONLY
1
WARNING: FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
U.S.A. ONLY
For EIP-2600
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the owner’s manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense.
The enclosed computer cable must be used with the device. The cable is provided to
ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
For EIP-250
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the owner’s manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of conformity
EIKI PROJECTOR, MODEL EIP-250
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Responsible Party:
EIKI INTERNATIONAL, INC.
30251 Esperanza Rancho Santa Margarita, CA 92688-2132
TEL: 800-242-3454
2
U.S.A. ONLY
How to Read this Owner’s Manual
■ The specifications are slightly different, depending on the model. However, you can connect and
operate all models in the same manner.
••
• In this owner’s manual, the illustration and the screen display are simplified for explanation, and
••
may differ slightly from the actual display. The examples used throughout this manual are based
on the EIP-2600 model.
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
MENU/HELP button
ENTER button
Adjustment buttons
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Press MENU/HELP.
1
• The “Picture” menu screen for the selected input mode is displayed.
Press Q or O and select “Picture”
2
to adjust.
Example: “Picture” screen menu for
COMPUTER (RGB) input
(EIP-2600)
Menu item
Picture SCR - ADJ PRJ - ADJ Help
Picture Mode
Contrast 0
Bright
Red
Blue
CLR Temp
TM
BrilliantColor
C.M.S. Setting
C.M.S.
DNR
Lamp Setting
Reset
SEL./ADJ. ENTER END
(P/R/O/Q)
RETURN button
•Press RETURN to return
to the previous screen
when the menu is
displayed.
MENU/HELP button
Standard
0
0
0
0
0
1
On
Off
Bright
Buttons used in
this operation
Button used in
this step
On-screen
display
38
Info
........Indicates safeguards for using the projector.
.........Indicates additional information for setting up and operating the
Note
projector.
For Future Reference
PP. 63 and 64
IndexMaintenance Troubleshooting
P. 67P. 49
3
Contents
Preparing
Introduction
How to Read this Owner’s Manual ....... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
How to Access the PDF Owner’s
Manuals .............................................. 9
Accessories ........................................ 10
Part Names and Functions ................. 11
Projector ............................................... 11
Rear View ............................................. 12
Inserting the Batteries .......................... 14
Usable Range ...................................... 15
Quick Start
Quick Start .......................................... 16
Setup and Projection ............................ 16
Setup
Setting up the Projector ...................... 18
Setting up the Projector ....................... 18
Standard Setup (Front Projection) ....... 18
Ceiling-mount Setup ............................ 18
Projection (PRJ) Mode ......................... 19
Screen Size and Projection Distance .. 20
Connections
Connecting the Projector to
Other Equipment .............................. 21
Controlling the Projector by
a Computer ....................................... 24
Connecting the Power Cord ............... 24
Using
Basic Operation
Tu r ning the Projector On/Off .............. 25
Tur ning the Projector on ....................... 25
Tur ning the Power off (Putting the
Projector into Standby Mode) ........... 25
Image Projection ................................. 26
About the Setup Guide ........................ 26
Adjusting the Projected Image ............ 26
Correcting Trapezoidal Distortion ........ 28
Switching the Input Mode .................... 29
Adjusting the Volume ........................... 29
Displaying the Black Screen and
Tu rning off the Sound Temporarily .... 29
Resize Mode ......................................... 30
Useful Features
Operating with the Remote Control .... 32
Displaying and Setting the
Break Timer........................................ 32
Displaying the Pointer .......................... 32
Using the Spot Function ...................... 32
Switching the Eco+Quiet Mode ........... 32
Auto Sync (Auto Sync Adjustment) ..... 33
Freezing a Moving Image .................... 33
Selecting the Picture Mode .................. 33
Displaying an Enlarged Portion of
an Image ............................................ 33
Using the Remote Control as the
Wireless Computer Mouse ................ 34
Menu Items ......................................... 35
Using the Menu Screen ...................... 38
Menu Selections (Adjustments) ........... 38
Picture Adjustment (“Picture” Menu) ... 40
Selecting the Picture Mode .................. 40
Adjusting the Image ............................. 41
Adjusting the Color Temperature ......... 41
Adjusting the Colors ............................. 41
Progressive........................................... 42
Reducing Image Noise (DNR) ............. 42
Lamp Setting ........................................ 42
Adjusting the Projector Image
(“SCR - ADJ” Menu) ......................... 43
Setting the Resize Mode ...................... 43
Adjusting the Image Position ............... 43
Keystone Correction ............................ 43
Setting the On-screen Display ............. 43
Closed Caption .................................... 44
Selecting the Background Image ........ 44
Selecting the Setup Guide ................... 44
Reversing/Inverting Projected
Images ............................................... 44
Selecting the On-screen Display
Language ........................................... 44
Adjusting the Projector Function
(“PRJ - ADJ” Menu) .......................... 45
Auto Sync (Auto Sync Adjustment) ..... 45
Auto Power Off Function ...................... 45
Auto Restart Function .......................... 45
STANDBY Mode ................................... 45
Setting the Confirmation Sound
(System Sound) ................................. 45
Speaker Setting .................................... 45
Audio Input (EIP-2600 only) ................. 46
Selecting the Transmission Speed
(RS-232C) .......................................... 46
Fan Mode Setting ................................. 46
System Lock Function .......................... 46
Checking the Lamp Life Status ........... 47
Keylock Function .................................. 47
4
Troubleshooting with the
“Help” Menu ...................................... 48
Utilizing the “Help” Menu Functions .... 48
Reference
Appendix
Maintenance ....................................... 49
Maintenance Indicators ...................... 50
Regarding the Lamp ........................... 52
Lamp ..................................................... 52
Caution Concerning the Lamp ............ 52
Replacing the Lamp ............................. 52
Removing and Installing the
Lamp Unit .......................................... 53
Resetting the Lamp Timer .................... 54
Connecting Pin Assignments ............. 55
RS-232C Specifications and
Commands ....................................... 57
Computer Compatibility Chart ............ 62
Troubleshooting .................................. 63
Specifications ..................................... 65
Dimensions ......................................... 66
Index ................................................... 67
5
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its installation,
use and servicing.
1. Read Instructions
All the safety and operating instructions should be
read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be
retained for future reference.
3. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be
followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example,
near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming pool;
and the like.
8. Accessories
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power supply to
your home, consult your product dealer or local
power company. For products intended to operate
from battery power, or other sources, refer to the
operating instructions.
12. Grounding or Polarization
This product is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from the
product.
14. Lightning
For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the cable system. This
will prevent damage to the product due to lightning
and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
17. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
6
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
• DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a
trademark of Texas Instruments.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States
and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
•
All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas
Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse
assemble or discompile the contents thereof.
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of
Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts
accompanying this license (“Fonts”) and associated documentation files (the “Font Software”), to
reproduce and distribute the Font Software, including without limitation the rights to use, copy,
merge, publish, distribute, and/or sell copies of the Font Software, and to permit persons to whom
the Font Software is furnished to do so, subject to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies
of one or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or
characters in the Fonts may be modified and additional glyphs or characters may be added to the
Fonts, only if the fonts are renamed to names not containing either the words “Bitstream” or the
word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been
modified and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of
the Font Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK,
OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR
FROM OTHER DEALINGS IN THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream
Inc., shall not be used in advertising or otherwise to promote the sale, use or other dealings in this
Font Software without prior written authorization from the Gnome Foundation or Bitstream Inc.,
respectively. For further information, contact: fonts at gnome dot org.
19. Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
20. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
7
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp ruptures. In case
of lamp rupture, contact your
nearest EIKI Authorized
Dealer or Service Center for
replacement.
See “Regarding the Lamp” on
page
52.
Caution concerning the setup of the
projector
■ For minimal servicing and to maintain high
image quality, EIKI recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by an EIKI Authorized Dealer or Service Center.
Do not set up the projector in places
exposed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Caution regarding placing of the projector
■ Place the projector on a level site within the
adjustment range (9 degrees) of the adjustment foot.
■ After the projector is purchased, a faint smell
from the vent may appear when the power is
first turned on. This is normal and is not a
malfunction. It will disappear after the projector is used for a while.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Warning about placing the projector in
a high position
■ When placing the projector in a high position,
make certain it is carefully secure to avoid
personal injury caused by the projector falling down.
Do not subject the projector to hard
impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Avoid locations with extremes of
temperature.
■ The operating temperature of the projector is
from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
■ Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Ensure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat
damage. This does not indicate a malfunction. (See pages 50 and 51.) Remove the projector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
8
Caution regarding usage of the projector
■ If you are not to use the projector for a long
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other cables
connected to it.
■ If the power cord is unplugged while the cooling fan is running, some parts of the projector may still be hot. Use caution when handling the projector.
■ Do not carry the projector by holding the lens.
■ When storing the projector, ensure you at-
tach the lens cap to the projector. (See page
11.)
■ Do not expose the projector to direct sunlight
or place next to heat sources. Doing so may
affect the cabinet color or cause deformation
of the plastic cover.
Other connected equipment
■ When connecting a computer or other audiovisual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the owner’s manuals of the projector and the equipment to be connected for
instructions on how to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
■
If the projector starts to overheat due to setup
problems or blockage of the air vents, “
“ ” will illuminate in the lower left corner
of the picture. If the temperature continues to
rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after
a 60-second cooling-off period the projector will
enter standby mode. Refer to “Maintenance Indicators” on page 50 for details.
” and
Info
• The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the
fan speed. This does not indicate malfunction.
How to Access the PDF Owner’s Manuals
PDF owner’s manuals in several languages are included in the CD-ROM. To utilize
these manuals, you need to install Adobe
or Macintosh®).
Please download Adobe
®
Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals for Windows
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 Double click the “MANUALS” folder.
5 Double click the model (name of the folder)
that you want to view.
Note
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first,
then specify the desired file using the “File”, “Open” menu.
®
Reader® on your computer (Windows
®
(For Macintosh®, skip step 2).
6 Double click the language (name of the
folder) that you want to view.
7 Double click the pdf file to access the pro-
jector manuals.
®
9
Accessories
Supplied accessories
Remote control
for EIP-2600
3 RCA to mini D-sub 15 pin cable
(10' (3.0 m))
<QCNWGA043WJPZ>
• QUICK GUIDE
• Owner’s manual (this manual and CD-ROM)
for EIP-250
Optional accessories
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
Lens cap (attached)
Power cord*
(1 ) (2)
For U.S. and Canada, etc.
(6' (1.8 m))
<QACCDA007WJPZ>
* Use the power cord that corresponds to
the wall outlet in your country.
DIN-D-sub RS-232C adaptor
RGB cable
(10' (3.0 m))
<QCNWGA045WJPZ>
57
/64" (15 cm))
(5
<QCNWGA091WJPZ>
For Europe, except U.K.
(6' (1.8 m))
<QACCVA011WJPZ>
■ Lamp unit AH-62101
■ Storage case AH-62501
10
Part Names and Functions
Numbers in Z refer to the main pages in this owner’s manual where the topic is
explained.
Projector
Top View
Power
indicator
STANDBY/ON
button
For turning the
power on and
putting the
projector into
standby mode.
ENTER button
For setting
items selected
or adjusted on
the menu.
KEYSTONE
button
For entering the
Keystone
Correction mode.
Front View
Zoom ring
For enlarging/
reducing the picture.
Remote control
sensor
Exhaust vent
25, 50
25
38
28
26
15
49
25, 50
50
32
29
29
38, 48
38
Lamp indicator
Temperature warning
indicator
ECO+QUIET button
For lowering the noise
of the cooling fan and
extending the lamp life.
VOL (Volume) buttons
(–O/Q+)
For adjusting the
speaker sound level.
INPUT buttons (P/R)
For switching input mode.
MENU/HELP button
For displaying
adjustment and
setting screens, and
help screen.
Adjustment buttons
(P/R/O/Q)
For selecting menu items.
Intake vent
49
Speaker
45
HEIGHT
ADJUST lever
27
Focus ring
26
For adjusting
the focus.
Push both sides of the lens cap
to attach or remove.
11
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this owner’s manual where the topic is
explained.
Rear View
Terminals
*AUDIO 1 input terminal
COMPUTER/
COMPONENT input
terminal
Te rminal for computer RGB
and component signals.
*DVI-I input
terminal
Te rminal for
DVI digital,
computer RGB
and component
signals.
*AUDIO OUT
terminal
Audio output terminal of
equipment connected to the
audio input terminal.
MONITOR OUT
terminal
(Output terminal for computer RGB,
component signals. Shared for COMPUTER/COMPONENT)
Te rminal for connecting a monitor.
* EIP-2600 only
21
22
23
23
21
22
23
S-VIDEO input terminal
22
Te rminal for connecting
video equipment with an
S-video terminal.
RS-232C terminal
24
Te rminal for
controlling the
projector using a
computer.
34
Te rminal connecting
with the USB
terminal on the
computer for using
the supplied remote
control as the
computer mouse.
AUDIO 2 input
23
terminal
(AUDIO input
terminal for
EIP-250)
22
VIDEO input
terminal
Te rminal for
connecting video
equipment.
USB terminal
AC socket
24
Connect the supplied
Rear
adjustment
foot
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for
instructions on how to use it to secure the projector.
27
power cord.
Kensington Security
Standard connector
12
STANDBY button
For putting the projector
into the standby mode.
COMPUTER, *DVI,
S-VIDEO, VIDEO buttons
For switching to the
respective input modes.
BREAK TIMER button
For displaying the
break time.
MAGNIFY buttons
For enlarging/reducing
part of the image.
PAGE UP/PAGE
DOWN buttons
Same as the [Page Down] and
[Page Up] keys on a computer
keyboard, when with the USB
connection (using a USB cable
or the optional remote
receiver).
POINTER button
For displaying the
pointer.
MOUSE/Adjustment
buttons (P/R/O/Q)
• For moving the
computer cursor when with the USB
connection (using a USB cable or the
optional remote receiver).
• For selecting and adjusting menu
items.
L-CLICK/EFFECT
button
• For the Left click
when with the USB connection
(using a USB cable or the optional
remote receiver).
• For changing the pointer or spot
area.
KEYSTONE button
For entering the
Keystone Correction mode.
AUTO SYNC button
For automatically
adjusting images when
connected to a computer.
ECO+QUIET button
For lowering the noise
of the cooling fan and
extending the lamp life.
25
29
32
33
34
32
34
38
34
32
28
33
32
ON button
25
For turning the power
on.
FREEZE button
33
For freezing images.
AV MUTE button
29
For temporarily
displaying a black
screen and turning
off the sound.
VOL +/– (Volume)
29
buttons
For adjusting the
speaker sound level.
SPOT button
32
For displaying the
spotlight.
ENTER button
38
For setting items
selected or adjusted
on the menu.
R-CLICK/RETURN
34
button
38
• For the Right click
when with the USB
connection (using a
USB cable or the
optional remote
receiver).
• For returning to the
previous menu screen
during menu
operations.
MENU/HELP button
38
For displaying
48
adjustment and
setting screens, and
help screen.
RESIZE button
30
For switching the
picture size
(NORMAL, BORDER,
etc.).
PICTURE MODE
33
button
For selecting the
appropriate picture.
* EIP-2600 only
13
Part Names and Functions (Continued)
Inserting the Batteries
Pull down the tab on the cover and remove the cover
1
towards the direction of the arrow.
Insert the batteries.
2
• Insert the batteries making sure the polarities correctly match
the m and n marks inside the battery compartment.
Insert the lower tab of the cover into the opening,
3
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please
follow the precautions below.
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them
to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove
them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
14
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
Note
• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may
differ depending on the screen material.
When using the remote control
• Ensure that you do not drop it or expose it to
moisture or high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the projector away from the fluorescent lamp.
Remote control
30°
30°
Remote control
signal transmitters
Remote control sensor
23n (7 m)
15
Quick Start
This section shows the basic operation (projector connecting with the computer). For details, see
the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
3
STANDBY/ON
8
button
INPUT buttons
6
ENTER button
4
Adjustment buttons
5
(P/R/O/Q)
KEYSTONE
5
button
Zoom ring
4
Focus ring
4
HEIGHT
4
ADJUST lever
STANDBY button
8
ON button
3
COMPUTER button
6
ENTER button
4
Adjustment buttons
5
(P/R/O/Q)
KEYSTONE button
5
1. Place the projector facing a wall or a screen
_P. 18
2. Connect the projector to the computer and plug the power cord
into the AC socket of the projector
When connecting equipment other than a computer, see
pages 22 and 23.
_PP. 21, 24
3. Remove the lens cap and turn the projector on
On the projector On the remote control
_P. 25
16
4. Adjust the projected image with the Setup Guide
RGB
1024 × 768
COMPUTER
1 After the projector turns on, the Setup Guide appears.
(When “Setup Guide” is set to “On”. See page 44.)
2 Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.
3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup
Guide.
_PP. 26, 27
5. Correct trapezoidal distortion
Correcting trapezoidal distortion using Keystone Correction.
On the projector
On the remote control
Shrinks
upper side.
Shrinks
lower side.
_P. 28
6. Select the INPUT mode
Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.
On the
projector
• When you press INPUT on the projector, the INPUT list appears.
Press '/" to switch the INPUT mode.
On the remote
control
INPUT list
INPUT
COMPUTER
D
DVI-D Computer
D
DVI-D Video
On-screen display (RGB)
*
EIP-2600 only
*
_P. 29
7. Turn the computer on
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the
button again while the confirmation message is displayed to put the projector into standby mode.
On-screen display
_P. 25
On the
projector
On the remote
control
17
Setting up the Projector
Setting up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet
flat and level. Doing so will eliminate the need for Keystone correction and provide the best image
quality. (See page 28.)
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according
to the desired picture size. (See page 20.)
Example of standard setup
Side View
Screen
H
Lens center
L
Note
• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.
Ceiling-mount Setup
■ It is recommended that you use the optional
EIKI ceiling-mount adaptor and unit for this
installation. Before mounting the projector,
contact your nearest EIKI Authorized Dealer
or Service Center to obtain the recommended
ceiling-mount adaptor and unit (sold
separately).
18
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the mode
most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu.
See page 44.)
■ Ta ble mounted, front projection
[Menu item ➞ “Front”]
■ Ta ble mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
■ Ceiling mounted, front projection
[Menu item ➞ “Ceiling + Front”]
■ Ceiling mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Ceiling + Rear”]
Indication of the Projection Image Size and Projection Distance
Example: NORMAL Mode (4:3)
Picture Size
300"
200"
100"
80"
40"
32"
80"
×
64"
×
48"
×
24"
160"
60"
×
120"
240"×180"
"
5'8
"–
4'11
(1.5 m – 1.7 m)
9'10
11'4
"–
(3.0 m
"
3.5 m)
–
12'3
14'2
"–
(3.7 m
"
4.3 m)
–
24'7
28'4
"–
(7.5 m
"
8.6 m)
–
36'10
(11.2 m)
Projection
Distance
"
19
Loading...