Page 1
EFERGY RECOMMENDS THAT INSTALLATION IS CARRIED OUT BY A QUALIFIED ELECTRICIANEFERGY RECOMMENDS THAT INSTALLATION IS CARRIED OUT BY A QUALIFIED ELECTRICIAN
1. CHOOSE SENSOR TYPE
a) CT sensor
To measure household consumption connect the Mini CT sensor to the feed cable (see
Sensor1 on the diagram bellow). If your electricity panel differs to the one shown here
please contact us at info.aus@efergy.com
If you want to measure solar generation connect the Mini CT sensor to the cable coming
from the solar inverter (see Sensor2 on the diagram bellow).
To connect the CT sensor pull the clasp to open it, place the sensor around the feed cable
and push the clasp to shut. Insert the sensor jack in to the base of the transmitter.
UNDERSTAND YOUR HOME ENERGY CONSUMPTION
AND SOLAR GENERATION LIKE NEVER BEFORE
The engage solar kit lets you manage multiple circuits in your home from anywhere, any time
through the engage online portal.
This kit is perfect for monitoring your solar generation and comparing it to your energy
consumption info. Instantly see the cost of using energy in your home (updates every 10s).
HOW IT WORKS
Our engage solar kit is simple to install and use. One CT sensor is clipped onto the live feed
cable at your breaker panel and another on the cable coming from the solar inverter. These
sensors are then connected to the efergy transmitters. The transmitters wirelessly send real time
data to the hub. The engage hub is connected to your internet router via ethernet cable.
2. CHOOSE TRANSMITTER TYPE
The engage solar kit is packaged with either a standard efergy transmitter or a waterproof
transmitter. If you require TPM or IR/Optical transmitters, please visit our website at
www.efergy.com to purchase.
3. CONNECT THE ENGAGE HUB
a) Plug the engage hub into a mains power source
using the supplied AC adaptor, and into a spare port
on a router with internet access using the LAN cable
provided.
b) There are 3 lights on the top of the hub. First, the
red light will light continuously, showing that the hub
is powered on. The yellow light (centre) will come on
next, indicating that the hub is looking for a
transmitter within range. A green light states that a
working internet connection has been connected to
the hub.
c) Within a minute or two you should see both the
yellow light and green light come on and stay on solid
for a few seconds and then go out. The lights may or
may not illuminate at the same time. Once you see
the yellow and green lights come on for a few
seconds and then go out, you are ready to register
your engage hub.
Note: If your router does not recognize your new hub, the router may
need to be reset. Simply do this by pushing the reset button on the
router itself (sometimes this requires the use of a paper clip).
b) Typical IR/ Optical Sensor Installation (DIY)
Meters generally have an output port located on the front panel. The output port will have
digits in imp/kWh mentioned below it. e.g. 1000 imp/kWh.
Unscrew the sensor body from the sensor base. Peel off the adhesive on the base of the
sensor and position the sensor base hole over the flashing LED
Re-attach the sensor body to the sensor base and screw firmly in place.
Insert the jack on the end of the sensor wire into input socket on the transmitter. The
transmitter will send the information wirelessly to the display.
Note: The engage solar kit is packaged with 2 Mini CT sensors. If you require TPM AC / AC
Sensor or IR / Optical sensors, please visit our website at www.efergy.com to purchase.
OR
CT Sensor
Breaker Transmitter
CT Sensor
Classic / Waterproof Transmitter
Sensor2
Sensor1
Solar inverter Electricity panel
Page 2
engage hub kit 2.0
HH-2.0
433.5MHz
10 Sec.
40 - 70m
AC/DC Adaptor
TPM transmitter Classic transmitter
ELECTRICITY MONITORING
TRANSMITTER
Waterproof transmitter
SET UP THE ONLINE SERVICE
Visit http://engage.efergy.com, register and follow our step by step setup process on-screen.
It may be more comfortable for you to carry out this process on a laptop near where the
transmitter is installed or get someone to assist you during the pairing process.
To register your device you will need to input your MAC address and serial number which can
be found on the underside of your engage hub.
LINK THE TRANSMITTER
When prompted by the on-screen instructions, complete installation by pressing Link button on
the website and on your transmitter. This must be done within 30 seconds of each other. You
may press the link button on the transmitter several times during this time. Do not press and
hold this button, simply push and release it each time for period.
ASK US
If you have any problems at any point during registration please check the FAQs within the Help
section at:
http://engage.efergy.com/content/getting-started
Alternatively, if you have any questions about using your installation guide or want further
information on saving energy, you can contact us or visit our website.
+613 939 995 56 / info.au@efergy.com
+64 21 724 382 / info@efergynz.co.nz
www.efergy.com
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
Note: For 120/240V residential services, please set the voltage set-point to 120V
WHAT’S IN THE BOX
TECHNICAL INFORMATION
Model Name
Model Number
Frequency
Transmission Time
Transmission Range
Engage Hub Power
http://engage.efergy.com
MONITOR YOUR HOME
ENERGY CONSUMPTION
& SOLAR GENERATION
FROM ANYWHERE
+
-
ELECTRICITY MONITORING
TRANSMITTER
ELECTRICITY MONITORING
TRANSMITTER
ELECTRICITY MONITORING
TRANSMITTER
ELECTRICITY MONITORING
TRANSMITTER
QUICK START GUIDE
ELECTRICITY MONITORING
TRANSMITTER
1x engage hub AC/DC
Adaptor
1x LAN
Cable
2 x Mini CT
2 x Waterproof
Transmitters
Loading...