Genesis Chime-Strobe Installation Sheet
There are field-configurable options for selecting dB output,
chime signal, and constant noncoded voltage or single-stroke
coded voltage operation. See Figure 1.
Note: A Genesis Signal Master is required when chimes are
configured for coded operation.
The strobe includes a field-configurable switch for selecting the
desired candela output. The candela output setting is locked in
place and remains visible after final installation.
This strobe features an enhanced synchronization circuit to
comply with the latest requirements of UL 1971 Signaling
Devices for the Hearing Impaired. Synchronized operation
requires a separately installed synchronization control module.
See Table 2 for a list of compatible synchronization modules.
Table 2: Compatible synchronization module models [1]
Description Number
Description
The Genesis Chime-Strobe is a fire alarm notification
appliance designed for indoor ceilings and walls. See Table 1
for a list of model numbers.
Table 1: Models
Description Numbers
Chime-strobe, 15 to 110 multicd, white
Chime-strobe, 15 to 110 multicd, white, with FIRE marking
Chime-strobe, 15 to 110 multicd, red
Chime-strobe, 15 to 110 multicd, red, with FIRE marking
Trim plate, white ADTG1T
Trim plate, red ADTG1RT
ADTG1-CVM
EG1-CVM
G1-CVM
ADTG1F-CVM
EG1F-CVM
G1F-CVM
ADTG1R-CVM
EG1R-CVM
G1R-CVM
ADTG1RF-CVM
EG1RF-CVM
G1RF-CVM
EG1T
G1T
EG1RT
G1RT
MG1-CVM
XLSG1-CVM
ZG1-CVM
MG1F-CVM
XLSG1F-CVM
ZG1F-CVM
MG1R-CVM
XLSG1R-CVM
ZG1R-CVM
MG1RF-CVM
XLSG1RF-CVM
ZG1RF-CVM
MG1T
XLSG1T
ZG1T
MG1RT
XLSG1RT
ZG1RT
Genesis Signal Master
Snap-on Mount
Genesis Signal Master Remote Mount
Auto-Sync Output Module SIGA-CC1S SIGA-MCC1S
Dual Input Signal Module SIGA-CC2A SIGA-MCC2 A
Auxiliary Power Supply APS6A APS10A
Power Supply BPS6A BPS10A
[1] Synchronization module requirements are determined by the
application.
EG1M
ADTG1M
EG1M-RM MG1M-RM G1M-RM
MG1M
XLSG1M
Installation
Install this device in accordance with applicable requirements
in the latest editions of the NFPA codes and standards, and in
accordance with the local authorities having jurisdiction.
WARNING: Electrocution hazard. To avoid personal injury or
death from electrocution, remove all sources of power and
allow stored energy to discharge before installing or removing
equipment.
Caution: Electrical supervision requires the wire run to be
broken at each terminal. Do not loop the signaling circuit field
wires around the terminals.
To install the chime-strobe:
1. Remove the cover by depressing both tabs on the top of
the unit with a small screwdriver and twisting slightly.
G1M
ZG1M
© 2010 UTC Fire & Security. All rights reserved. 1 / 4 P/N 3100562 • REV 2.0 • ISS 19AUG10
2. Set the chime signal, sound output level, and desired
C
operation settings. See Figure 1.
• To change the chime signal from steady to temporal,
cut from circle J1 to the edge of the circuit board.
• To change the chime operation from noncod ed to
coded (single-stroke), cut from circle J2 to the edge of
the circuit board.
• To change the chime sound output level from high dB
to low dB, cut the J3 trace between the holes.
3. Slide the candela switch to the desired candela output by
aligning it with the indicator located beside the switch. See
Figure 2.
4. Connect the chime terminals to the signal circuit field
wiring. For the unit to function properly, observe polarity.
See Figure 1.
• For single-stroke coded voltage operation, see
Figure 3.
• For constant noncoded voltage operation, see
Figure 4.
5. Mount the unit onto a compatible electrical box, making
sure not to overtighten the mounting screws.
6. Replace the cover by aligning it at the bottom, then
snapping it in at the top.
7. Test the unit for proper operation.
Figure 1: Chime settings
Wiring
Figure 3: Wiring for single-stroke coded voltage operation
+
-
4
+
S
H
-
STROBE +
2
STROBE -
CHIME +
1
HIME -
1. Chime in (coded power signal)
2. Strobe in (continuous power signal)
3. Resistor, value determined by the control panel
4. Genesis Signal Master
5. To next appliance, EOL resistor, or Class A circuit return
6. One wire each side of screw head
Notes
• Polarity shown in alarm condition
• The strobe circuit can be silenced without turning off strobes
3
+
-
5
6
1
J1
1. J1: Chime signal jumper
2. J2: Coded/non-coded jumper
3. J3: Chime sound output
Figure 2: Candela switch
J2
110
75
30
15
2
3
J3
Figure 4: Wiring for constant noncoded voltage operation
+
+
1
-
1. From NAC output
2. To next appliance, EOL, or Class A return
Note: Signal polarity is shown in the alarm condition.
-
+
-
+
2
-
Maintenance
This unit is not serviceable or repairable. Should the unit fail to
operate, contact the supplier for replacement.
Perform a visual inspection and an operational test twice a
year or as directed by the local authority having jurisdiction.
Do no change the factory-applied finish.
2 / 4 P/N 3100562 • REV 2.0 • ISS 19AUG10
Figure 5: UL 1971 minimum light output (% of rating vs. angle)
0
1
0
5
-25
-30
-35
-40
-45
-50
-55
-60
-65
-70
-75
-80
-85
-90
9590858075706560555045403530252015
100
-20
-15
-10
-5
10
15
20
25
30
505
10
1015202530354045505560657075808590
2
35
40
45
50
55
60
1. Angle
2. Minimum UL required candela light output
____ % of rated candela vertical specification
- - - - % of rated candela horizontal specification
Specifications
Voltage 24 VDC or 24 VFWR nominal
Strobe operating
current
Light output Selectable at 15, 30, 75, and 110 cd
Sound level output See Table 4
Default settings
Signal
Sound level
output
Operation
Signals
Steady
Temporal
Coded
Operating modes
Noncoded
Coded
Wire size 12 to 18 AWG (0.75 TO 2.50 mm²)
Compatible electrical
boxes
Operating environment
Temperature
Relative humidity
See Table 3
Steady
High dB
Noncoded
60 strokes per minute
3-stroke pattern
Maximum 60 strokes per minute
Continuous voltage
Single-stroke controlled by voltage
2-1/2 in. (64 mm) deep single-gang box
4 in. square box 1-1/2 in. (38 mm), 2-gang
4 in. octagonal with G1T or G1RT trim
accessory
32 to 120°F (0 to 49°C)
0 to 93% noncondensing
Table 3: Strobe operating current in RMS (A)
15 cd 30 cd 75 cd 110 cd
VDC 0.099 0.134 0.233 0.277
VFWR 0.154 0.195 0.338 0.383
VDC = Volts direct current, regulated and filtered
VFWR = Volts full wave rectified
Operating currents shown above were measured by UL at 16 VDC and
16 VFWR.
65
70
95
Table 4: ULI Ratings, temporal output (private mode)
75
80
Signal High db Low db
85
Temporal 56.9 52.5
9
100
Steady 58.2 52.8
dBA = Decibels, A-weighted
UL464: Sound level output at 10 ft (3.05 m) measured in a reverberant
room at 16 V.
Regulatory information
Manufacturer Edwards, A Division of UTC Fire & Security
Americas Corporation, Inc.
8985 Town Center Parkway, Bradenton, FL
34202, USA
Year of
manufacture
The first two digits of the DATE MFG number
(located on the product identification label) are
the year of manufacture
UL rating Regulated 24 DC and 24 FWR
Environmental
UL: Indoor
class
Synchronization Meets UL 1971 requirements. Maximum allowed
resistance between any two devices is 20 Ω.
Refer to specifications for the synchronization
control module, this strobe, and the control panel
to determine allowed wire resistance.
Agency listings Meets UL1638, UL1971 (see Figure 1) a nd
UL464 (private mode)
Contact information
For contact information, see www.utcfireandsecurity.com.
P/N 3100562 • REV 2.0 • ISS 19AUG10 3 / 4
4 / 4 P/N 3100562 • REV 2.0 • ISS 19AUG10
Loading...