Page 1
EU-4307
Quick Installation Guide
06-2019 / v1.0
Page 2
I. Product Information
I-1. Package Contents
USB Type-C to 2.5G Gigabit Ethernet Adapter QIG
I-2. System Requirements
- Intel Premium III 1GHz ( or above)
- 256MB RAM/CD-ROM / 100MB Hard Disk Space (at least) / 100MB Hard
Disk Space (at least) / USB Type C Port
- Windows 7/8/8.1/10, Mac OS 10.6 – 10.10 or above
I-3. Safety
In order to ensure the safe operation of the device and its users, please read
and act in accordance with the following safety instructions.
1. The USB Fast Ethernet Adapter is designed for indoor use only; do not place
the USB Fast Ethernet Adapter outdoors.
2. Do not place the USB Fast Ethernet Adapter in or near hot/humid places,
such as a kitchen or bathroom.
3. The USB Fast Ethernet Adapter contains small parts which are a danger to
small children under 3 years old. Please keep the USB Fast Ethernet
Adapter out of reach of children.
4. There are no user-serviceable parts inside the USB Fast Ethernet Adapter. If
you experience problems with the USB Fast Ethernet Adapter, please
contact your dealer of purchase and ask for help.
5. The USB Fast Ethernet Adapter is an electrical device and as such, if it
becomes wet for any reason, stop using it immediately. Contact an
experienced electrical technician for further help.
1
Page 3
II. Installation
1. Switch on your computer and connect the Ethernet Adapter to an
available USB type C port of your computer.
Never use force to insert the USB adapter.
2. Mac users please download the driver from
https://www.edimax.com/download to your computer. For Window users,
the built-in setup wizard will automatically install the driver.
3. Please follow the instructions in the appropriate chapter for your
operating system.
2
Page 4
II-1. Windows
Driver Installation
1. Connect the Ethernet Adapter to an available USB type C port of your
computer. Double click to run the installer.
2. The driver will then be installed automatically. Opens up Computer
Management, click “System Tools”, “Device Manager”, then “Network
adapters”, “Realtek Gaming USB 2.5GbE Family Controller” should appear
if the driver is installed successfully.
3
Page 5
II-2. Mac OS
Driver Installation
1. Enter the MAC OS 10.6 to 10.13 folder and click the “RTUNICvx.x.x.pkg”
(“x.x.x” is driver revision number), and the following driver setup dialog
will appear. “Click Continue” to start the installation and follow the
instructions to continue the installation.
2. Click “Continue” to read the Read Me interface, choose the language,
accept the software license agreement, and then continue the installation
process.
4
Page 6
3. You might need to enter your user/password during the driver installation.
4. Click “Continue Installation” to continue the installation process.
5. Click “Restart” to restart your Mac OSX system and finish the installation.
5
Page 7
6. After booting up your Mac OSX system, plug your EU-4307 USB dongle
onto the USB type C port of your Mac OSX system. Refer to the following
information to double check that your USB dongle has been identified
properly by your Mac OSX system and that the driver has been installed
correctly.
(1) You can check the Vendor/Product ID information of your USB
dongle from here.
6
Page 8
(2) You can check the installed RTUNIC Mac OSX driver version
information by running the “kextstat” command
7. Choose Apple menu, System Preferences, then click Network. Select the
new “RTUNIC USB 3.1 to Gigabit Ethernet” network interface and press
“Create” followed by “Apply” for the new network interface to take effect.
8. The new “RTUNIC USB 3.1 to Gigabit Ethernet” driver should be ready.
7
Page 9
COPYRIGHT
Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission from Edimax Technology Co., Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability, or fitness for any particular purpose. Any software described in this
manual is sold or licensed as is. Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right
to revise this publication and to make changes from time to time in the contents hereof
without the obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly different from
those shown in this QIG. The software and specifications are subject to change without
notice. Please visit our website www.edimax.com for updates. All brand and product
names mentioned in this manual are trademarks and/or registered trademarks of their
respective holders.
8
Page 10
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with any other antenna or
transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any changes or modifications not expressly
approved by the party responsible for compliance could void the authority to operate equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be
less than 2.5cm (1 inch) during normal operation.
Federal Communications Commission (FCC) RF Exposure Requirements
This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and
had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65
Supplement C. The equipment version marketed in US is restricted to usage of the channels 1-11 only. This
equipment is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND
THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual
recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special
attention must be paid to the dangers of electric shock and static electricity when working with electrical
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to
ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI
version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and
Switzerland.
EU Countries Not Intended for Use
None
9
Page 11
EU Declaration of Conformity
English: This equipment is in compliance with the essential requirements and other relevant
provisions of Directive 2014/30/EU, 2014/35/EU.
Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la
directive 2014/30/EU, 2014/35/EU.
Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními
směrnic 2014/30/EU, 2014/35/EU.
Polski: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami
określonymi Dyrektywą UE 2014/30/EU, 2014/35/EU.
Română: Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale
Directivei 2014/30/EU, 2014/35/EU.
Русский: Это оборудование соответствует основным требованиям и положениям Директивы
2014/30/EU, 2014/35/EU.
Magyar: Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek
(2014/30/EU, 2014/35/EU).
Türkçe: Bu cihaz 2014/30/EU, 2014/35/EU. direktifleri zorunlu istekler ve diğer hükümlerle ile
uyumludur.
Українська: Обладнання відповідає вимогам і умовам директиви 2014/30/EU, 2014/35/EU.
Slovenčina: Toto zariadenie spĺňa základné požiadavky a ďalšie príslušné ustanovenia smerníc
2014/30/EU, 2014/35/EU.
Deutsch: Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 2014/30/EU, 2014/35/EU.
Español: El presente equipo cumple los requisitos esenciales de la Directiva 2014/30/EU,
2014/35/EU.
Italiano: Questo apparecchio è conforme ai requisiti essenziali e alle altre disposizioni applicabili
della Direttiva 2014/30/EU, 2014/35/EU.
Nederlands: Dit apparaat voldoet aan de essentiële eisen en andere van toepassing zijnde bepalingen
van richtlijn 2014/30/EU, 2014/35/EU.
Português: Este equipamento cumpre os requesitos essênciais da Directiva 2014/30/EU, 2014/35/EU.
Norsk: Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv
2014/30/EU, 2014/35/EU.
Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta
bestämmelser i direktiv 2014/30/EU, 2014/35/EU.
Dansk: Dette udstyr er i overensstemmelse med de væ sentligste krav og andre relevante
forordninger i direktiv 2014/30/EU, 2014/35/EU.
suomen kieli: Tämä laite täyttää direktiivien 2014/30/EU, 2014/35/EU. oleelliset vaatimukset ja muut
asiaankuuluvat määräykset.
-----------------------------------------------------------------------------------------------------------------------
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as household or general waste. It
should be handed over to the applicable collection point for the recycling of electrical and electronic
equipment, or returned to the supplier for disposal.
10
Page 12
Declaration of Conformity
We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the
equipment described below complies with the requirements of the European R&TTE
directives.
Equipment:
USB 3.1(Type C) to 2.5 Giga ethernet Port NIC
Model No.:
EU-4307
The following European standards for essential requirements have been followed:
Directives 2014/30/EU
EN 55032:2015+AC:2016 Class B
EN 55035:2017
EN 61000-4-2:2009
EN 61000-4-3:2006+A1:2008+A2:2010
EN 61000-4-4:2012
EN 61000-4-5:2014+A1:2017
EN 61000-4-6:2014
EN 61000-4-8:2010
EN 61000-4-11:2004+A1:2017
Directives 2014/35/EU
Safety (LVD)
:
IEC 60950-1:2005 (2nd Edition)+Am 1:2009+Am 2:2013
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
Date of Signature:
June, 2019
Signature:
Printed Name:
Albert Chang
Title:
Director
Edimax Technology Co., Ltd.
Edimax Technology Europe B.V.
Fijenhof 2,
5652 AE Eindhoven,
The Netherlands
a company of :
Edimax Technology Co., Ltd.
No. 278, Xinhu 1st Rd.,
Neihu Dist., Taipei City,
Taiwan
Signature:
Printed Name:
David Huang
Title:
Director
Edimax Technology Europe B.V.
11
Loading...