ECS Q77H2-TI User Manual

Q77H2-TI USER MANUAL
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.
Disclaimer
The information in this document is subject to change without notice. The manufac­turer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publica­tion and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.
Other product names used in this manual are the properties of their respective owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal­lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits govern­ing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
ii
Q77H2-TI USER MANUAL
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the follow­ing conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference
that may cause undesired operation.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interference­causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.
The manual consists of the following:
Describes features of the motherboard.
page 1
Describes installation of motherboard components.
page 7
page 29
page 61
Installing the Motherboard
Introducing the Motherboard
Provides information on us­ing the BIOS Setup Utility.
Describes the motherboard software.
Limits and methods of mesurement of radio disturbance char­acteristics of information technology equipment
EN 55022
EN 61000-3-2
Disturbances in supply systems caused
EN 61000-3-3
Disturbances in supply systems caused by household appli­ances and similar electrical equipment “ Voltage fluctuations”
EN 55024
Information technology equipment-Immunity characteristics­Limits and methods of measurement
EN 60950
Safety for information technology equipment including electri­cal business equipment
CE marking
About the Manual
This device is in conformity with the following EC/EMC directives:
Chapter 4
Chapter 1
Chapter 2
Chapter 3 Using BIOS
Using the Motherboard Software
Chapter 5 Trouble Shooting
Provides basic trouble shoot­ing tips.
page 65
iii
Q77H2-TI USER MANUAL
Chapter 2 7
Installing the Motherboard 7
Safety Precautions.............................................................................7
Installing the Motherboard in a Chassis......................................7
Checking Jumper Settings...........................................................8
Installing Hardware..................................................................10
Installing the Processor...........................................................10
Installing the CPU Cooler.........................................................12
Installing Memory Modules....................................................13
Installing Add-on Cards...........................................................14
Connecting Optional Devices..................................................16
Installing a Hard Disk Drive/Optical Disk Drive......................24
Connecting Case Components.......................................................26
TABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction...................................................................................1
Pakage Contents............................................................................1
Specifications................................................................................2
Motherboard Components..........................................................4
I/O Ports..............................................................................................6
Chapter 3 29
Using BIOS 29
About the Setup Utility........................ .......................................29
The Standard Configuration........................ ...........................29
Entering the Setup Utility.......................................................29
Resetting the Default CMOS Values.....................................30
Using BIOS........................................................................................30
BIOS Navigation Keys..............................................................31
Main Menu.............................................................................32
Advanced Menu......................................................................33
Chipset Menu..........................................................................49
Tweak Menu...........................................................................52
Boot Menu..............................................................................57
Security Menu.........................................................................58
Exit Menu................................................................................59
Updating the BIOS...................................................................60
iv
Q77H2-TI USER MANUAL
Chapter 4 61
Using the Motherboard Software 61
Auto-installing under Windows XP/7/8........................................61
Running Setup.........................................................................61
Manual Installation..........................................................................63
Chapter 5 65
Trouble Shooting 65
Start up problems during assembly..............................................65
Start up problems after prolong use............................................66
Maintenance and care tips..............................................................66
Basic Troubleshooting Flowchart...................................................67
1
Q77H2-TI USER MANUAL
Chapter 1
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the Q77H2-TI motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA1155 socket for Intel® 3rd Generation CoreTM vPro i7/i5 and CoreTM i3/Pentium®/Celeron
®
processors for high-end business or personal desktop markets.
This motherboard is based on Intel
®
Q77 Express Chipset for best desktop platform solution. It supports up to 16 GB of system memory with dual channel DDR3 1600/ 1333 SO-DIMM. Two mini PCI Express x1 slots are for extending usage (the PCIE1 supports half-card, the PCIE2 supports full-card and you can install a Mini SATA (mSATA) card into it).
It integrates USB 2.0 ports and USB 3.0 interface, supporting up to four USB 3.0 ports at the rear panel and five USB 2.0 ports (one 10-pin USB 2.0 header supports two USB
2.0 ports and three 5-pin USB 2.0 headers support additional 3 USB 2.0 ports).
The motherboard is equipped with advanced full set of I/O ports in the rear panel, including one RJ45 LAN connector, one Display port (DP), four USB 3.0 ports, one HDMI port, one DC_IN port and audio jacks for line-out and mircophone.
In addition, this motherboard supports two SATA 6Gb/s connectors for storage expansion.
Your motherboard package ships with the following items:
Package Contents
Q77H2-TI Motherboard User Manual DVD I/O Shield 1 SATA Cable and 1 SATA/Power Cable
    
Accessories may vary, please refer to actual goods you purchase.
Chapter 1
2
Q77H2-TI USER MANUAL
CPU
Specifications
Intel® Q77 Chipset
Supports Intel® Small Business Advantage
Supports Intel® Smart Connect Technology
Supports Intel® Rapid Start Technology
Chipset
Dual-channel DDR3 memory architecture
2 x 204-pin DDR3 SO-DIMM sockets support up to 16 GB
Supports DDR3 1600/1333 MHz DDR3 SDRAM
Memory
2 x mini PCI Express x1 slots (the PCIE1 supports half-card, the PCIE2 supports full-card and
you can install a Mini SATA (mSATA) card into it)
Supported by Intel® Q77 Express Chipset
- 2 x Serial ATA 6Gb/s devices
- RAID 0/1/5/10 Configuration
Expansion Slots
Storage
1 x HDMI port
1 x Display port (DP)
1 x 19V DC_IN port
1 x RJ45 LAN connector
4 x USB 3.0 ports
1 x Audio port (1 x line-out, 1 x Microphone)
Rear Panel I/O
LAN
Intel 82579LM Gigabit LAN
- 10/100/1000 Fast Ethernet Controller
- Wake-on-LAN and remote wake-up support
Realtek ALC662
- 2 Channel High Definition Audio Codec
- Compliant with HD audio specification
Audio
LGA1155 socket for
Intel® 3rd Generation CoreTM vPro i7/i5 and
CoreTM i3/Pentium®/Celeron® processors
DMI 5.0GT/s
Supports Intel® Active Management Technology
Supports Intel® Virtualization Technology
Supports Intel® Trusted Execution Technology
Supports Intel® Anti-Theft Technology
4 Phase Thermal Design Power
VRD 12.0
Supports DirectX 11.1 graphic core
Supports Intel® Turbo Boost 2.0 Technology
Supports Intel® Hyper-Threading Technology
NUVOTON NPCT420AA0WX TPM IC
Extra Chips
3
Q77H2-TI USER MANUAL
Chapter 1
AMI BIOS with 64Mb SPI Flash ROM
- Supports Plug and Play
- Supports ACPI & DMI
- Supports STR (S3) /STD (S4)
- Supports Hardware monitor
- Audio, LAN, can be disabled in BIOS
- F7 hot key for boot up devices option
- Supports PgUp clear CMOS Hotkey (Has PS2 KB Model only)
- Supports Multi-Language
System BIOS
1 x 4-pin CPU_FAN connector with smart fan function
1 x 4-pin SYS_FAN connector supports smart fan function
1 x 10-pin USB 2.0 header supports additional two USB 2.0 ports
3 x 5-pin USB 2.0 headers support additional 3 USB 2.0 ports
2 x Serial SATA 6Gb/s connectors
1 x Case open header
1 x Front Panel switch/LED header
1 x Front Panel audio header
1 x Clear CMOS jumper
1 x ME Unlock jumper
1 x COM header
1 x SATA power connector
1 x Buzzer header
1 x CIR header
1 x Digital Microphone header (optional)
1 x 2 channel audio speaker header (optional)
1 x LCD select jumper (optional)
1 x LVDS connetor (optional)
1 x Monitor switch header
Internal I/O Connectors & Headers
Form Factor Thin Mini ITX Size, 170mm x 170mm
AP Support Supports Norton/Cyberlink
Chapter 1
4
Q77H2-TI USER MANUAL
Motherboard Components
5
Q77H2-TI USER MANUAL
Chapter 1
Table of Motherboard Components
LABEL COMPONENTS
LGA1155 socket for Intel® 3
rd
Generation CoreTM vPro i7/i5
and Core
TM
i3/Pentium®/Celeron® Processors
2. DMIC Digital microphone header (optional)
3. SPKR 2 Channel audio speaker header (optional)
4. F_AUDIO Front panel audio header Mini PCI Express x 1 slot (supports full-card and you can install a Mini SATA (mSATA) card into it)
6. CLR_CMOS Clear CMOS jumper
7. CASE Case open header
8. DIMM1~2 204-pin DDR3 SDRAM SO-DIMMs
9. PCIE1 Mini PCI Express x 1 slot (supports half-card)
10. SATA1~2 Serial ATA 6Gb/s connectors
11. ME_UNLOCK ME Unlock jumper
12. SATA_PWR SATA power connector
13. F_USB Front panel USB 2.0 header
14. USB_CR 5-pin USB 2.0 header supports card reader or other USB 2.0 device
15. USB_CAM 5-pin USB 2.0 header supports camera or other USB 2.0 device
16. COM Onboard serial port header
17. F_PANEL Front panel switch/LED header
18. SYS_FAN 4-pin system cooling fan connector
19. CPU_FAN 4-pin CPU cooling fan connector
20. USB_TP 5-pin USB 2.0 header supports one USB 2.0 device
21. LVDS LVDS connector (optional)
22. CIR Consumer infrared header
23. DISP_BRT LVDS brightness control header
24. MON_SW LVDS brightness ON/OFF switch header
25. LCD_SEL LCD panel select header (optional)
5. PCIE2
1. CPU Socket
Chapter 1
6
Q77H2-TI USER MANUAL
I/O Ports
1. 19V DC_IN Port
Connect the DC_IN port to the power adapter.
2. Display Port (DP)
You can connect the display device to the display port.
3. HDMI Port
You can connect the display device to the HDMI port.
4. USB 3.0 Ports
Use the USB 3.0 ports to connect USB 3.0 devices.
5. LAN Port
Connect an RJ-45 jack to the LAN port to connect your computer to the Network.
6. Line-out (lime) It is used to connect to speakers or headphones.
7. Microphone (pink) It is used to connect to a microphone.
LAN LED Status Description
OFF No dat a Orange blinking Active OFF No link Green Link
Activity LED
Link LED
Link LED
LAN Port
Chapter 2
7
Q77H2-TI USER MANUAL
Chapter 2
Installing the Motherboard
2-1. Safety Precautions
2-2. Installing the motherboard in a Chassis
This motherboard carries a Thin Mini ITX form factor of 170 x 170 mm. Choose a chassis that accommodates this form factor. Make sure that the I/O template in the chassis matches the I/O ports installed on the rear edge of the motherboard. Most system chassis have mounting brackets installed in the chassis, which corresponds to the holes in the motherboard. Place the motherboard over the mounting brack­ets and secure the motherboard onto the mounting brackets with screws.
Follow these safety precautions when installing the motherboard:
Wear a grounding strap attached to a grounded device to avoid damage from static electricity.
Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard.
Leave components in the static-proof bags.
Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
Do not over-tighten the screws as this can stress the motherboard.
Chapter 2
8
Q77H2-TI USER MANUAL
No. Components
1LCD_SEL
2CLR_CMOS
3ME_UNLOCK
This section explains how to set jumpers for correct configuration of the motherboard.
2-3. Checking Jumper Settings
1. LCD_SEL: LCD panel select header (optional)
1.When your panel connects to LVDS, please check LCD_SEL header setting first.
2.Due to the differences of the panel parameters, please follow the above illustration to place the jumper caps.
Chapter 2
9
Q77H2-TI USER MANUAL
To avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save and Exit Setup”.
The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.
2. CLR_CMOS: Clear CMOS jumper
3. ME_UNLOCK: ME unlock jumper
Chapter 2
10
Q77H2-TI USER MANUAL
2-4. Installing Hardware
This motherboard has an LGA1155 socket.
When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.
You may be able to change the settings in the system Setup Utility. We strongly recommend you do not over-clock processor or other compo­nents to run faster than their rated speed.
The following illustration shows CPU installation components.
A. Press the hook of lever down with your thumb and pull it to the right side to release it from retention tab.
B. Lift the tail of the load lever and rotate the load plate to fully open position.
C. Grasp the edge of the package substrate. Make sure pin 1 indicator is on your bottom-left side. Aim at the socket and place the package carefully into the socket by purely vertical motion.
2-4-1. Installing the Processor
Chapter 2
11
Q77H2-TI USER MANUAL
D. Rotate the load plate onto the package IHS (Intergraded Heat Spreader). Engage the load lever while pressing down lightly onto the load plate. Secure the load lever with the hook under retention tab. Then the cover will flick automatically.
Please save and replace the cover onto the CPU socket if processor is re­moved.
Chapter 2
12
Q77H2-TI USER MANUAL
A. Apply some thermal grease onto the contacted area between the heatsink and the CPU, and make it to be a thin layer.
B. Fasten the cooling fan supporting base onto the CPU socket on the motherboard. And make sure the CPU fan is plugged to the CPU fan connector.
C. Connect the CPU cooler power connector to the CPU_FAN connector.
2-4-2. Installing the CPU Cooler
Install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.
Avoid using cooling fans with sharp edges in case the fan casing and the clips cause serious damage to the motherboard or its components.
To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heat sink instal­lation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.
DO NOT remove the CPU cap from the socket before installing a CPU.
Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with the cap on the LGA1155 socket.
The following illustration shows how to install CPU fan.
Chapter 2
13
Q77H2-TI USER MANUAL
2-4-3. Installing Memory Modules
This motherboard accommodates two memory modules. It can support two 204-pin DDR3 1600/1333.
Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.
You must install at least one module in any of the two slots. Total memory capacity is 16 GB.
Refer to the following to install the memory modules.
Install the DIMM module into the slot and press it firmly down until it fits in place. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot.
Chapter 2
14
Q77H2-TI USER MANUAL
2-4-4. Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.
PCIE1~2 Slots The mini PCI Express x1 slots are for extending usage, one sup-
ports half-card, and the other supports full-card.
Chapter 2
15
Q77H2-TI USER MANUAL
Follow these instructions to install a wireless card:
1 Remove a blanking plate from the system case, and insert the wireless
card into the MINIPCIE slot rightwards, then tighten the two screws (Please refer to Picture 1).
2 Press the metal connector of the cable into the connector on the wireless
card. Ensure that the metal connector is correctly seated (Please refer to Picture 2).
3 Make the other end of the cable (with a gold screw) through the upper hole
of the bracket, and tighten the antenna on to the gold screw after install­ing a metal gasket on the screw (Please refer to Picture 3).
Picture 1 Picture 2 Picture 3
* For reference only
Chapter 2
16
Q77H2-TI USER MANUAL
2-4-5. Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional devices:
No. Components No. Components
1 F_USB 8 MON_SW
2USB_CAM9 CIR
3USB_CR10 DMIC
4COM11F_AUDIO
5USB_TP12CASE
6LVDS13SATA1~2
7 DISP_BRT 14 SATA_PWR
Chapter 2
17
Q77H2-TI USER MANUAL
The motherboard has one USB 2.0 headers supporting two USB 2.0 ports. Addition­ally, some computer cases have USB 2.0 ports at the front of the case. If you have this kind of case, use auxiliary USB 2.0 connector to connect the front-mounted ports to the motherboard.
1. F_USB: Front Panel USB 2.0 header
Please make sure that the USB cable has the same pin assignment as indi­cated above. A different pin assignment may cause damage or system hang­up.
2 & 3 & 5. USB_CAM/USB_CR/USB_TP: 5-pin USB 2.0 header supports camera /card reader or other USB 2.0 devices
Users please note to install the card to the correct header.
Chapter 2
18
Q77H2-TI USER MANUAL
6. LVDS: LVDS connector (optional)
1. You can connect the large end of the cable to the LED Panel, and connect the other small end to the slot on the motherboard.
2.Due to the chipset limitation, using dual displays LVDS(AIO) + VGA or LVDS(AIO) + HDMI will cause the problem that you may not enter BIOS setup or have the display problem.
Connect a serial port extension bracket to this header to add a serial port to your system.
4. COM: Onboard serial port header
Chapter 2
19
Q77H2-TI USER MANUAL
7. DISP_BRT: LVDS connector (optional)
8. MON_SW: LVDS brightness ON/OFF switch header
Chapter 2
20
Q77H2-TI USER MANUAL
10. DMIC: Digital microphone header (optional)
9. CIR: Consumer infrared header
Chapter 2
21
Q77H2-TI USER MANUAL
If you use AC97 Front Panel, please tick off the option of Disabled Front Panel Detect ”. If you use HD Audio Front Panel, please don’ t tick off Disabled Front Panel Detect ” .
* For reference only
AC97 Audio Configuration: To enable the front panel audio connector to support AC97 Audio mode.
The front panel audio header allows the user to install auxiliary front-oriented mi­crophone and line-out ports for easier access. This header supports HD audio by default. If you want connect an AC97 front panel audio to HD onboard headers, please set as below picture.
11. F_AUDIO: Front Panel Audio Header
Chapter 2
22
Q77H2-TI USER MANUAL
SATA1~2 connectors are used to support the Serial ATA 6Gb/s device. Simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Paral­lel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
13. SATA1~2: Serial ATA III connectors
12. CASE: Chassis Intrusion Detect Header
This detects if the chassis cover has been removed. This function needs a chassis equipped with instrusion detection switch and needs to be enabled in BIOS.
Chapter 2
23
Q77H2-TI USER MANUAL
14. SATA_PWR: SATA power connector
Chapter 2
24
Q77H2-TI USER MANUAL
* For reference only
2-4-6. Installing a Hard Disk Drive/Optical Disk Drive
This section describes how to install a Hard Disk Drive/Optical Disk Drive.
About SATA Connectors
Your motherboard features two SATA connectors supporting a total of two drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard inter­face for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the Hard Disk Drive/ Optical Disk Drive.
Installing Hard Disk Drive/Optical Disk Drive
To install the Hard Disk Drive (HDD)/Optical Disk Drive (ODD), use the HDD/ODD/SATA cables that support the Hard Disk Drive/Optical Disk Drive/Serial ATA protocol.
Refer to the illustration below for proper installation:
1 Attach either end of the single SATA cable to the SATA port on the
motherboard. 2 Attach the other end of the single SATA cable to the hard disk drive. 3 Attach the linked end of the combo HDD/ODD cable to the Hard Disk Drive/
Optical Disk Drive. Please note that, connect the black cable to the hard
disk Drive, then connect the orange cable to the optical disk drive. 4 Attach the other end of the combo HDD/ODD cable to the SATA port and
SATA_PWR connector on the motherboard. Please note that, connect the
black cable to the SATA_PWR connector, and connect the orange cable to
the SATA port.
Chapter 2
25
Q77H2-TI USER MANUAL
About mSATA Connectors
Your motherboard features two Mini PCI Express x1 slots, the PCIE2 supports full­card, you can install a Mini SATA (mSATA) card into it.
Refer to the illustration below for proper installation:
1 Insert a Mini SATA (mSATA) card into the PCIE2 Slot.
2 Lower the handle and tighten the screws.
Chapter 2
26
Q77H2-TI USER MANUAL
After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:
2-4-7. Connecting Case Components
No. Components
1 F_PANEL
2SYS_FAN
3CPU_FAN
4SPKR
Chapter 2
27
Q77H2-TI USER MANUAL
1. F_PANEL: Front Panel Header
The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases.
Hard Drive Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.
Power/Sleep/Message waiting LED
Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentary-con­tact switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momen­tary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.
Chapter 2
28
Q77H2-TI USER MANUAL
2 & 3 . SYS_FAN (System Cooling FAN Power Connector) &CPU_FAN (CPU cool­ing FAN Power Connector)
Users please note that the fan connector supports the CPU cooling fan of 1.1A ~ 2.2A (26.4W max) at +12V.
Connect the CPU cooling fan cable to CPU_FAN. Connect the system cooling fan connector to SYS_FAN.
Connect the case speaker cable to SPKR.
4. SPKR: 2 Channel audio speaker header (optional)
This concludes Chapter 2. The next chapter covers the BIOS.
Chapter 3
Q77H2-TI USER MANUAL
29
About the Setup Utility
The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s con­figuration status and provides you with options to set system parameters. The pa­rameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.
The BIOS Setup Utility enables you to configure:
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we rec­ommend that you read this chapter in case you need to make any changes in the future.
This Setup Utility should be used:
when changing the system configuration
when a configuration error is detected and you are prompted to make changes to the Setup Utility
when trying to resolve IRQ conflicts
when making changes to the Power Management configuration
when changing the password or making other changes to the Security Setup
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:
Press DEL to enter SETUP
Chapter 3
Using BIOS
Hard drives, diskette drives and peripherals
Video display type and display options
Password protection from unauthorized use
Power Management features
Chapter 3
Q77H2-TI USER MANUAL
30
Press the delete key to access BIOS Setup Utility.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for informa­tion.
Some options (marked with a triangle


) lead to submenus that enable you to change
the values for the option. Use the cursor arrow keys to scroll through the items in the submenu.
Resetting the Default CMOS Values
When powering on for the first time, the POST screen may show a “CMOS Settings Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings and Save it to reset the default CMOS values.
Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message.
BIOS Information
System Language [English]
System Date [Tue 11/06/2012] System Time [00:00:29]
Choose the system default language.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Main Advanced Chipset T weak Boot Security Exit
Chapter 3
Q77H2-TI USER MANUAL
31
The default BIOS setting for this motherboard apply for most conditions with optimum performance. We do not suggest users change the default values in the BIOS setup and take no responsibility to any damage caused by changing the BIOS settings.
BIOS Navigation Keys
The BIOS navigation keys are listed below:
KEY FUNCTION
Scrolls through the items on a menu
+/-
F2 Pr
evious Value
F3 Optimized Defaults
F1 General Help
ESC

Enter Select
In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle


 .
F4 Save & Exit
For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual.
Exits the current menu
Change Opt.
Chapter 3
Q77H2-TI USER MANUAL
32
Main Menu
System Date & Time
The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.
System Language (English)
This item is used to set system language.
When you enter the BIOS Setup program, the main menu appears, giving you an overview of the basic system information. Select an item and press <Enter> to display the submenu.
BIOS Information
System Language [English]
System Date [Tue 11/06/2012] System Time [00:00:29]
Choose the system default language.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Main Advanced Chipset T weak Boot Security Exit
Chapter 3
Q77H2-TI USER MANUAL
33
The Advanced menu items allow you to change the settings for the CPU and other system.
Advanced Menu
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
LAN Configuration
PC Health Status Power Management Setup ACPI Settings CPU Configuration SA TA Configuration USB Configuration AMT Configuration Intel TXT(LT) Configuration Super IO Configuration Trusted Computing Intel(R) Rapid Start T echnology Intel(R) Smart Connect T echnology
LAN Configuration Parameters


 

 

Main Advanced Chipset Tweak Boot Security Exit


 

 







 

 

 

 

Chapter 3
Q77H2-TI USER MANUAL
34
LAN Configuration
The item in the menu shows the LAN-related information that the BIOS automatically detects.
Press <Esc> to return to the Advanced Menu page.
Onboard LAN Controller (Enabled)
Use this item to enable or disable Onboard LAN 1 controller.
Enable or Disable Onboard NIC.
LAN Configuration
Onboard LAN Controller [Enabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Tweak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Chapter 3
Q77H2-TI USER MANUAL
35
PC Health Status
On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.
Main Advanced Chipset Tweak Boot Security Exit
System T emperature : 30O C CPU Fan Speed : 0 RPM System Fan Speed : 3253 RPM CPU Voltage : 1.016 V AXG Voltage : 0.440 V DIMM Voltage : 1.496 V
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
-=- PECI Mode -=­Offset to TCC Activation Temp. : -48
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Smart Fan Function
PC Health Status
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
CPU Smart Fan Control [Enabled]
Smart Fan Mode [Normal]
High Limit Offset (-) : 30 Low Limit Offset (-) : 4 0 High Limit PWM : 2 0 0 Low Limit PWM : 5 8
System Smart Fan Control [Enabled] Smart Fan Mode [Normal]
High Limit Offset (-) : 30 Low Limit Offset (-) : 4 0 High Limit PWM : 2 0 0 Low Limit PWM : 5 8
Main Advanced Chipset Tweak Boot Security Exit
Scroll to this item and press <Enter> to view the following screen:
Smart Fan Function

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
CPU/System Smart FAN Control (Enabled)
This item allows you to enable/disable the control of the CPU/System fan speed by changing the fan voltage.
SMART Fan Mode (Normal)
This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quiet mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjust depending on users’ parameters.
Enable CPU SmartFan
Press <Esc> to return to the PC Health Status page.
Chapter 3
Q77H2-TI USER MANUAL
36
System Temperature
CPU Fan Speed
System Fan Speed
CPU Voltage
AXG Voltage
DIMM Voltage
System Component Characteristics
These items display the monitoring of the overall inboard hardware health events, such as System temperature, CPU & DIMM voltage, CPU & System fan speed... etc.
Press <Esc> to return to the Advanced Menu page.
Chapter 3
Q77H2-TI USER MANUAL
37
Power Management Setup
This page sets up some parameters for system power management operation.
Resume By PME (Disabled)
This item specify whether the system will be awakened from power saving modes when activity or input signal of the specified hardware peripheral or components is detected.
Resume By USB(S3) (Disabled)
This item allows you to enable/disable the USB device wakeup function from S3 mode.
EUP Function (Enabled)
This item allows user to enable or disable EUP support.
Press <Esc> to return to the Advanced Menu page.
Power Management Setup
Resume By RING [Disabled]
Resume By PME [Disabled] Wake on LAN [Enabled] Resume By USB (S3) [Disabled] EUP Function [Enabled] Power LED Type [Single Color LED]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Tweak Boot Security Exit
Version 2. 15.1229. Copyright (C) 2012 American Megatrends, Inc.
About Resume by Ring
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Resume By RING (Disabled)
The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem. You must use an ATX power supply in order to use this feature.
Power LED Type (Single Color LED)
This item shows the type of the power LED.
Wake on LAN (Enabled)
Use this item to enable or disable integrated LAN to wake the system. (The Wake on LAN cannot be disabled if ME is on at Sx state.) If disabled, resume by USB (S3) will not be available.
Chapter 3
Q77H2-TI USER MANUAL
38
ACPI Configuration
The item in the menu shows the highest ACPI sleep state when the system enters suspend.
ACPI Sleep State [S3(Suspend to RAM)]
This item allows user to enter the ACPI S3 (Suspend to RAM) Sleep State (default).
Press <Esc> to return to the Advanced Menu page.
ACPI Settings
ACPI Sleep State [S3 (Suspend to RAM)]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Select the highest ACPI sleep state the system will enter when the Suspend button is pressed.
Main Advanced Chipset Tweak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select


:Select Screen
:Select Item
F2:Previous Values F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Chapter 3
Q77H2-TI USER MANUAL
39
Limit CPUID Maximum (Disabled)
Use this item to enable or disable the maximum CPUID value limit, you can enable this item to prevent the system from “rebooting” when trying to install Windows NT
4.0.
CPU Configuration
The item in the menu shows the CPU Configuration.
Intel(R) Celeron(R) CPU G530T @ 2.00GHz
This is display-only field and diaplays the information of the CPU installed in your computer.
EM64T (Supported)
This item shows the computer supports EMT64.
Processor Speed (2000MHz)
This item shows the current processor speed.
Processor Stepping (206a7)
This item shows the processor stepping version.
Microcode Revision (28)
This item shows the Microcode version.
Processor Cores (2)
This item shows the core number of the processor.
Intel HT Technology (Not Supported)
This item shows that the computer supports Intel HT Technology or not.
Intel VT-x Technology (Supported)
This item shows that the computer supports Intel VT-x Technology or not.
CPU Configuration Intel(R) Celeron(R) CPU G530T @ 2.00GHz
EMT64 Supported Processor Speed 2000 MHz Processor Stepping 206a7 Microcode Revision 2 8 Processor Cores 2 Intel HT Technology Not Supported Intel VT -x Technology Supported
Limit CPUID Maximum [Disabled]
Execute Disable Bit [Enabled] Intel Virtualization T echnology [Enabled] CPU C3 Report [Enabled] CPU C6 Report [Enabled] Enhanced Halt (ClE) [Enabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Disabled for Windows XP
Main Advanced Chipset Tweak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Chapter 3
Q77H2-TI USER MANUAL
40
Excute Disable Bit (Enabled)
This item allows the processor to classify areas in memory by where application code can execute and where it cannot. When a malicious worm attempts to insert code in the buffer, the processor disables code execution, preventing damage or worm propagation. Replacing older computers with Execute Disable Bit enabled systems can halt worm attacks, reducing the need for virus related repair.
CPU C3 Report (Disabled)
Use this item to enable or disable CPU C3 (ACPI C2) report to OS.
Enhanced Halt (ClE) (Enabled)
Use this item to enable the CPU energy-saving function when the system is not run­ning.
CPU C6 Report (Enabled)
Use this item to enable or disable CPU C6 (ACPI C3) report to OS.
Press <Esc> to return to the Advanced Menu page.
Intel Virtualization Technology (Enabled)
When disabled, a VMM cannot utilize the additional hardware capabilities provided by Vandor Pool Technology.
Chapter 3
Q77H2-TI USER MANUAL
41
SATA Configuration
Use this item to show the mode of serial SATA configuration options.
SATA Mode (AHCI Mode)
Use this item to select SATA mode.
mSATA/SATA Port1~2 (Not Present)
This motherboard supports two SATA channels and one mSATA channel, each chan­nel allows one mSATA/SATA device to be installed. Use these items to configure each device on the mSATA/SATA channel.
Press <Esc> to return to the Advanced Menu page.
SA TA Configuration
SAT A Mode [AHCI Mode]
SAT A Port1 Not Present Spin Up Device [Disabled] External SAT A [Disabled]
SAT A Port2 Not Present Spin Up Device [Disabled] External SAT A [Disabled]
mSAT A Not Present Spin Up Device [Disabled] External SAT A [Disabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Determines how SAT A controller(s) operate.
Main Advanced Chipset T weak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Spin Up Device (Disabled)
Use this item to enable or disable the spin up device.
External SATA (Disabled)
Use this item to enable or disable the external SATA.
Chapter 3
Q77H2-TI USER MANUAL
42
USB Configuration
Use this item to show the information of USB configuration.
Legacy USB Support (Enabled)
Use this item to enable or disable support for legacy USB devices.
Press <Esc> to return to the Advanced Menu page.
USB Configuration
All USB Devices [Enabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
USB Support Parameters
Legacy USB Support [Enabled]
Main Advanced Chipset T weak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
All USB Devices (Enabled)
Use this item to enable or disable all USB devices.
Chapter 3
Q77H2-TI USER MANUAL
43
AMT Configuration
Use this item to show the information of AMT configuration.
Intel AMT [Disabled]
MEBx Setting Screen [Disabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enable/Disable Intel(R) Active Management T echnology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enable, this requires additional firmware in the SPI device.
Main Advanced Chipset T weak Boot Security Exit
Intel AMT (Disabled)
Use this item to enable or disable Intel(R) Active Management Technology BIOS Ex­tension. iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device.
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
MEBx Setting Screen (Disabled)
Use this item to enable or disable Intel ME BIOS Extension setting screen.
Press <Esc> to return to the Advanced Menu page.
Chapter 3
Q77H2-TI USER MANUAL
44
Intel TXT(LT) Configuration
Use this item to show the information of Intel TXT(LT) configuration.
Intel Trusted Execution T echnology Configuration Intel TXT support only can be enabled/disabled is SMX
is enabled. VT and VT-d support must also be enabled prior to TXT .
Secure Mode Extensions (SMX) Enabled
Intel TXT(LT) Support [Disabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enables or Disables Intel(R) TXT(LT) support.
Main Advanced Chipset T weak Boot Security Exit
Secure Mode Extensions (Enabled)
Use this item to enable or disable secure mode extension.
F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Intel TXT(LT) Configuration (Disabled)
Use this item to enable or disable Intel Intel(R) TXT(LT) support.
Press <Esc> to return to the Advanced Menu page.
Chapter 3
Q77H2-TI USER MANUAL
45
Super IO Chip (F71808A)
This item shows the information of the super IO chip.
Super IO Configuration
Use this item to show the information of Super IO configuration.
Super IO Configuration Super IO Chip F71808A
Serial Port 0 Configutation
CIR Controller Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset T weak Boot Security Exit
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Set Parameters of Serial Port 0 (COMA)


F1:General Help
+/- : Change Opt.
Enter : Select
 
:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit


Serial Port 0 Configuration
Scroll to this item and press <Enter> to view the following screen:
Serial Port (Enabled)
This item allows you to enable or disable serial port.
Device Settings (IO=3F8h; IRQ=4)
This item shows the information of the device settings.
Change Settings (Auto)
Use this item to change device settings.
Serial Port 0 Configuration
Serial Port [Enabled]
Device Settings IO=3F8h; IRQ=4;
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enable or Disable Serial Port (COM)
Change Settings [Auto]
Main Advanced Chipset Tweak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select


:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Press <Esc> to return to the Super IO Configuration page.
Chapter 3
Q77H2-TI USER MANUAL
46
Press <Esc> to return to the Advanced Menu page.
CIR Controller Configuration
Scroll to this item and press <Enter> to view the following screen:
CIR Controller (Enabled)
This it
em allows you to enable or disable CIR controller.
Press <Esc> to return to the Super IO Configuration page.
CIR Controller Configuration
CIR Controller [Enabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enable or Disable CIR Controller
Main Advanced Chipset Tweak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select


:Select Screen
:Select Item
F2:Previous Values F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Trusted Computing
Use this item to show the information of trusted computing.
TPM Support (Enabled)
Use this item to enable or disable the TPM support. O.S will not show TPM. Reset of platform is required.
TPM Configuration
TPM Support [Enabled] TPM State [Disabled]
Pending operation [None] Current TPM Status Information
TPM Enabled Status: [Disabled] TPM Active Status: [Activated] TPM Owner Status: [Unowned]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enables or Disables BIOS support for security device. O.S. will not show security Device. TCG EFI protocol and INT1A interface will not be available.
Main Advanced Chipset Tweak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select


:Select Screen
:Select Item
F2:Previous Values F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Chapter 3
Q77H2-TI USER MANUAL
47
TPM State (Disabled)
Use this item to enable or disable the security device.
Pending Operation (None)
Use this item to schedule an operation for the security device.
TPM Enabled Status (Disabled)
This item displays the TPM status to be enabled or disabled.
TPM Active Status (Activated)
This item displays the TPM status to be activated or not.
TPM Owner Status (Unowned)
This item displays the TPM status to be owned or not.
Intel(R) Rapid Start Technology
Use this item to show the information of Intel(R) Rapid Start Technology.
Intel(R) Rapid Start Technology (Disabled)
Use this item to enable or disable Intel(R) Rapid Start Technology.
Intel(R) Rapid Start T echnology Intel(R) Rapid Start Technology [Disabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Tweak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select


:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Press <Esc> to return to the Advanced Menu page.
Press <Esc> to return to the Advanced Menu page.
Chapter 3
Q77H2-TI USER MANUAL
48
Intel(R) Smart Connect Technology
Use this item to show the information of Intel(R) Smart Connect Technology.
ISCT Configuration (Disabled)
Use this item to enable or disable ISCT configuration.
ISCT Configuration [Disabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Enable/Disable ISCT Configuration.
Main Advanced Chipset Tweak Boot Security Exit
F1:General Help
+/- : Change Opt.
Enter : Select


:Select Screen
:Select Item
F2:Previous Values F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Press <Esc> to return to the Advanced Menu page.
Chapter 3
Q77H2-TI USER MANUAL
49
The chipset menu items allow you to change the settings for the North Bridge chipset, South Bridge chipset and other system.
Chipset Menu
Scroll to this item and press <Enter> and view the following screen:
System Agent Configuration
IGD Memory (64M)
This item shows the information of the IGD (Internal Graphics Device) memory.
DVMT Memory (256M)
When set to Fixed Mode, the graphics driver will reserve a fixed position of the sys­tem memory as graphics memory, according to system and graphics requirements.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
System Agent Configuration
PCH Configuration
ME Configuration
Main Advanced Chipset Tweak Boot Security Exit

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
System Agent (SA) Parameters
VT-d Capability (Supported)
This item shows that the computer supports VT-d capability or not.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Tweak Boot Security Exit
System Agent Configuration
IGD Memory [64M]
DVMT Memory [256M] VT-d Capability Supported
VT-d [Enabled]
Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device.

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Press <Esc> to return to the Chipset Menu page.
VT-d (Enabled)
Use this item to check to enable VT-d function on MCH.
Chapter 3
Q77H2-TI USER MANUAL
50
PCH Configuration
Scroll to this item and press <Enter> to view the following screen:
Restore AC Power Loss (Power Off)
This item enables your computer to automatically restart or return to its operating status.
Azalia HD Audio (Enabled)
This item enables or disables Azalia HD audio.
Azalia Internal HDMI codec (Enabled)
This item enables or disables Azalia Internal HDMI codec.
Case Open Warning (Disabled)
This item enables or disables the warning if the case is opened up, and the item below indicates the current status of the case.
Chassis Opened (No)
This item indicates whether the case has been opened.
Press <Esc> to return to the Chipset Menu page.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Tweak Boot Security Exit

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
PCH Configuration
Restore AC Power Loss [Power Off]
Audio Configuration Azalia HD Audio [Enabled] Azalia Internal HDMI codec [Enabled]
Case Open Warning [Disabled] Chassis Opened [No]
Select AC power state when power is re-applied after a power failure.
Chapter 3
Q77H2-TI USER MANUAL
51
ME Configuration
Scroll to this item and press <Enter> to view the following screen:
ME FW Version (8.1.0.1265)
This item shows the ME FW version.
Press <Esc> to return to the Chipset Menu page.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Tweak Boot Security Exit

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Management Engine T echnology Configuration ME FW Version 8.1 . 0.1265
Chapter 3
Q77H2-TI USER MANUAL
52
Enhanced Intel SpeedStep Technology (Enabled)
This item allows users to enable or disable the EIST (Enhanced Intel SpeedStep Tech­nology).
This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.
Tweak Menu
CPU OverClocking Configuration
Scroll to this item to view the following screen:
CPU Frequency (1/100 MHz) (10000)
This item shows the information of CPU frequency.
CPU Ratio (20)
This item allows users to control non turbo CPU ratio.
Main Advanced Chipset T weak Boot Security Exit
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
CPU OverClocking Configuration

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Tweak
CPU OverClocking Configuration
Chipset OverClocking Configuration B.O.M.P . T echnology [Enabled] Intel(R) Core(TM) i5-3475S CPU @ 2.90GHz
Processor Speed 2900 MHz Memory Frequency 1333 MHz T otal Memory 2048 MB (DDR3)
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Main Advanced Chipset T weak Boot Security Exit
CPU OverClocking Configuration CPU Frequency(1/100 MHz) 10000
CPU Ratio 2 0
Enhanced Intel SpeedStep T echnology [Enabled]
Runtime Turbo Enable [Disabled] Over Clocking Extra Vol.(1/256 V) 0 IA Core Current Max(1/8 Amp) 78 0 iGFX Core Current Max(1/8 Amp) 26 0 Long Duration Maintained 2 8
Enhanced Intel SpeedStep T echnology
Chapter 3
Q77H2-TI USER MANUAL
53
Press <Esc> to return to the Tweak Menu page.
Runtime Turbo Enable (Disabled)
This item shows if CPU support runtime turbo or not.
OverClocking Extra Vol.(1/256V) (0)
Use this item to set over clocking extra voltage.
IA Core Current Max(1/8 Amp) (780)
Use this item to control CPU Current Limit.
iGFX Core Current Max(1/8 Amp) (260)
Use this item to control iGFX Core Current Limit.
Long Duration Maintained (28)
Use this item to control the time window over PL1 value should be maintained. This is for Turbo mode.
Chapter 3
Q77H2-TI USER MANUAL
54
Chipset OverClocking Configuration
Scroll to this item to view the following screen:
Memory Timing Cofiguration CAS# Latency(tCL) 9
RAS# to CAS# Delay(tRCD) 9 Row Precharge Time(tRP) 9 RAS# Active Time(tRAS) 2 4 Write Recovery Time(tWR) 1 0 Row Refresh Cycle Time(tRFC) 74 Active to Active Delay(tRRD) 4 Write to Read Delay(tWTR) 5 Read CAS# Precharge(tRTP) 5 Four Active Window Delay(tFAW) 20
CAS# Latency(tCL) (7)
This item determines the operation of DDR SDRAM memory CAS (column address strobe). It is recommended that you leave this item at the default value. The 2T setting requires faster memory that specifically supports this mode.
Row Precharge Time(tRP) (7)
This item specifies Row precharge to Active or Auto-Refresh of the same bank.
RAS# to CAS# Delay(tRCD) (7)
This item specifies RAS# to CAS# delay to Rd/Wr command to the same bank.
RAS# Active Time(tRAS) (20)
This item specifies the RAS# active time.
Write Recovery Time(tWR) (8)
This item specifies the write recovery time.
Row Refresh Cycle Time(tRFC) (59)
This item specifies the row refresh cycle time.
Write to Read Delay(tWTR) (4)
This item specifies the write to read delay time.
Active to Active Delay(tRRD) (4)
This item controls the active bank x to active bank y in memory clock cycles.
Read CAS# Precharge(tRTP) (4)
This item controls the Read to precharge delay for memory devices, in memory clock cycles.
Memory Multiplier Configuration
Performance Memory Profiles [Automatic]
Memory Timing Configuration CAS# Latency(tCL) 7
Row Precharge Time(tRP) 7 RAS# to CAS# Delay(tRCD) 7 RAS# Active Time(tRAS) 2 0 Write Recovery Time(tWR) 8 Row Refresh Cycle Time(tRFC) 59 Write to Read Delay(tWTR) 4 Active to Active Delay(tRRD) 4 Read CAS# Precharge(tRTP) 4 Four Active Window Delay(tFAW) 16
Intel Graphics Configuration Graphics Core Ratio Limit 20
Graphics Voltage(1/256 V) 0
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset T weak Boot Security Exit
The selection of Performance Memory Profiles which impacts memory sizing behavior.
Performance Memory Profiles (Automatic)
This item allows you to select the memory mode: Automatic, Manual, XMP Profile 1 or 2.

:Select Screen
+/- : Value
Enter : Select

:Select Item
F1:General Help
F2:Previous Value
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Chapter 3
Q77H2-TI USER MANUAL
55
Four Active Window Delay(tFAW) (16)
This item controls the four bank activate time in memory clock cycles.
Press <Esc> to return to the Tweak Menu page.
Graphics Core Ratio Limit (20)
This item allows you to control the internal GFX Turbo ratio.
Graphics Voltage(1/256) (0)
This item allows you to adjust the internal GFX voltage.
Chapter 3
Q77H2-TI USER MANUAL
56
When end-users encounter failure after attempting over-clocking, please take the following steps to recover from it.
1. Shut down the computer.
2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the PC up.
3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.
4. The BIOS returns to the default setting by itself.
Warning: Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.
Fail-Safe Procedures for Over-clocking
B.O.M.P. Technology (Enabled)
This item allows users to enable or disable B.O.M.P. technology. This function can run safe setting to setup menu when system boot fail 3 times.
Intel(R) Core(TM) i5-3475S CPU @ 2.90GHz
This is display-only field and displays the information of the CPU installed in your computer.
Processor Speed (2900 MHz)
This item shows the CPU speed.
Memory Frequency (1333 MHz)
This item shows the memory frequency.
Total Memory (2048 MB (DDR3))
This item shows the total memory.
Chapter 3
Q77H2-TI USER MANUAL
57
This page enables you to set the keyboard NumLock state.
Boot Menu
Boot Configuration
This item shows the information of the Boot Configuration.
Operation System Select (Windows 7 or other OS)
This item is used to select the operation system.
Launch PXE OpROM (Disabled)
The item enables or disables launch PXE Option ROM.
Launch Storage OpROM (Enabled)
Use this item to enable or disable the Storage OpROM.
Bootup NumLock State (On)
This item enables you to select NumLock state.
Quiet Boot (Enabled)
Use this item to enable or disable quiet boot.
Boot mode select (LEGACY)
Use this item to select boot mode.
Set Boot Priority
This item enables you to set boot priority for all boot devices.
Boot Option #1 /
2 /3 /4 /5 /6 /7
These items show the boot priorities.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Windows 7 or Other OS: Boot policy for Legacy OS.
Windows 8: Boot policy for UEFI OS without Compatibility Support Module(CSM).
Manual: User customized CSM parameters & boot policy.
Main Advanced Chipset T weak Boot Security Exit

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Boot Configuration
Operating system select [Windows 7 or othre OS]
Launch PXE OpROM [Disabled] Launch Storage OpROM [Enabled]
Bootup NumLock State [On] Quiet Boot [Enabled] Boot mode select [LEGACY]
Set Boot Priority
Boot Option #1 [Hard Disk] Boot Option #2 [CD/DVD] Boot Option #3 [USB/Floppy] Boot Option #4 [USB CD/DVD] Boot Option #5 [USB Hard Disk] Boot Option #6 [USB Flash] Boot Option #7 [Network]
Chapter 3
Q77H2-TI USER MANUAL
58
This page enables you to set setup administrator password and user password.
Security Menu
Administrator Password Status (Not Install)
This item shows administrator password installed or not.
User Password Status (Not Install)
This item shows user password installed or not.
System Mode state (Setup)
This item shows system mode setup or not.
Secure Boot state (Disabled)
This item allows you to enable or disable the secure boot state.
Secure Boot (Disabled)
This item is used to control the secure boot flow, it is possible only if system runs in User Mode.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Set Administrator Password
Main Advanced Chipset Tweak Boot Security Exit

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values
F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Administrator Password Status Not Install User Password Status Not Install
Administrator Password
System Mode state Setup Secure Boot state Disabled
Secure Boot [Disabled]
Chapter 3
Q77H2-TI USER MANUAL
59
This page enables you to exit system setup after saving or without saving the changes.
Exit Menu
Save Options
This item enables you to save the options that you have made.
Save Changes
This item enables you to save the changes that you have made.
Discard Changes
This item enables you to discard any changes that you have made.
Restore Defaults
This item enables you to restore the system defaults.
Save Changes and Reset
This item enables you to reset system setup after saving the changes.
Discard Changes and Exit
This item enables you to exit system setup without saving any changes.
Discard Changes and Reset
This item enables you to reset system setup without saving any changes.
Boot Override
Use this item to select the boot device.
Save as User Defaults
This item enables you to save the changes that you have made as user defaults.
Restore User Defaults
This item enables you to restore the user defaults.
Save Changes and Reset
Discard Changes and Exit Discard Changes and Reset
Save Options Save Changes Discard Changes
Restore Defaults Save as User Defaults Restore User Defaults
Boot Override
Main Advanced Chipset Tweak Boot Security Exit
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1229. Copyright (C) 2012 American Megatrends, Inc.
Reset the system after saving the changes.

F1:General Help
+/- : Change Opt.
Enter : Select

:Select Screen
:Select Item
F2:Previous Values F3:Optimized Defaults
F4:Save & Exit
ESC:Exit
Chapter 3
Q77H2-TI USER MANUAL
60
Updating the BIOS
You can download and install updated BIOS for this motherboard from the manufacturer’s Website. New BIOS provides support for new peripherals, improve­ments in performance, or fixes for known bugs. Install new BIOS as follows:
This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.
1 If your motherboard has a BIOS protection jumper, change the setting to
allow BIOS flashing.
2 If your motherboard has an item called Firmware Write Protect in Ad-
vanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.)
3 Prepare a bootable device or create a bootable system disk. (Refer to
Windows online help for information on creating a bootable system disk.)
4 Download the Flash Utility and new BIOS file from the manufacturer’s
Web site. Copy these files to the bootable device.
5 Turn off your computer and insert the bootable device in your computer.
(You might need to run the Setup Utility and change the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the bootable device first.)
6 At the C:\ or A:\ prompt, type the Flash Utility program name and the file
name of the new BIOS and then press <Enter>. Example: AFUDOS.EXE
040706.ROM
7 When the installation is complete, remove the bootable device from the
computer and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically.
61
Q77H2-TI USER MANUAL
Chapter 4
Chapter 4
Using the Motherboard Software
The auto-install DVD-ROM makes it easy for you to install the drivers and software. The support software DVD-ROM disc loads automatically under Windows XP/7/8. When you insert the DVD-ROM disc in the DVD-ROM drive, the auto-run feature will automatically bring up the installation screen. The screen has four buttons on it:
Setup, Utilities, Browse CD and Exit.
Auto-installing under Windows XP/7/8
Displays the path for all software and drivers available on the disk.
Open Windows Explorer and show the contents of the support disk.
Click “Exit” button to close the Auto-Setup
window.
Browse CD:
Click the “Setup” button to select and run the software installation program.
Click the “ Utilities” button to select and install the Intelligent Utility.
Information:
Follow these instructions to install device drivers and software for the motherboard:
The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.
1. Click Setup. The installation program begins:
Running Setup
The motherboard identification is located in the upper left-hand corner.
62
Q77H2-TI USER MANUAL
Chapter 4
2. Click Next. The following screen appears:
3. Check the box next to the items you want to install. The default options are recommended.
5. Follow the instructions on the screen to install the items.
4. Click Next to run the Installation Wizard. An item installation screen appears:
Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to re­start a few times to complete the installation.
Windows 8 will show the following screen after system restart, you must select “Desktop” in the bottom left to install the next driver.
63
Q77H2-TI USER MANUAL
Chapter 4
If the auto-install DVD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Look
for the chipset and motherboard model, and then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.
Manual Installation
If the driver you want to install does not have a setup program, browse to the oper­ating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.
Windows 7/8 will appear below UAC (User Account Control) message after the system restart. You must select “Yes” to install the next driver. Continue
this process to complete the drivers installation.
64
Q77H2-TI USER MANUAL
Chapter 4
Memo
65
Q77H2-TI USER MANUAL
Chapter 5
Chapter 5
Trouble Shooting
Start up problems during assembly
After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips.
a) System does not power up and the fans are not running.
1. Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse. Leave only the motherboard, CPU with CPU cooler and power supply connected. Make sure the power cord is plugged into the wall socket & the switch on the Power Supply Unit (PSU) is turned “ on “ as well. Turn on again to see if the CPU and power supply fans are running.
2. Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case. This is to prevent damage from short circuit.
3. Check the CPU FAN connector is connected to the motherboard.
4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent pin may cause failure to boot and sometimes permanent damage from short circuit.
b) Power is on, fans are running but there is no display
1. Make sure the monitor is turned on and the monitor cable is properly connected to the PC.
2. Check the VGA adapter card (if applicable) is inserted properly.
3. Listen for beep sounds. If you are using internal PC speaker make sure it is connected. a. continuous 3 short beeps: memory not detected b. 1 long beep and 8 short beeps: VGA not detected
c) The PC suddenly shuts down while booting up.
1. The CPU may experience overheating so it will shutdown to protect itself. Apply the thermal grease onto the CPU heatsink & ensure the CPU fan is well-connected with the CPU heatsink. Check if the CPU fan is working properly while the system is running.
2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan.
66
Q77H2-TI USER MANUAL
Chapter 5
Start up problems after prolong use
After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. The following tips may help to revive the PC or identify the cause of failure.
1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When completed, follow up with a Load Optimised Default in the BIOS setup.
2. Check the CPU cooler fan for dust. Long term accumulation of dust will reduce its effectiveness to cool the processor. Clean the cooler or replace a new one if necessary.
3. Remove the hard drive, optical drive or DDR memory to determine which of these components may be at fault.
4. Check whether there is any bulked up electrolytic capacitor or abnormal component.
Your computer, like any electrical appliance, requires proper care and maintenance. Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can.
1. Keep your computer in a well ventilated area. Leave some space between the PC and the wall for sufficient airflow.
2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight and areas of high moisture content.
3. Routinely clean the CPU cooler fan to remove dust and hair.
4. In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humidity.
5. Add more memory to your computer if possible. This not only speeds up the system but also reduces the loading of your hard drive to prolong its life span.
6. If possible, ensure the power cord has an earth ground pin directly from the wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.
Maintenance and care tips
uB rewoP
desserp si no
.trats ot sliaf CP tub
seY
ylppuS rewoP fi kcehC
tinU
gnikrow si )USP(
oN
oN
dnuos peeB ynA
oN
kcehc dna SOMC RLC
rewop V21 UPC fi
detcennoc si
CP eht tratseR
?draob ro USP htiw melborP
AMR tcatnoc >- melborp draob fI
deulp si droc rewop CA gg
?no denrut si hctiws USP dna
seY
melborp draoB
AMR tcatnoc >-
oN
:speeb trohs 3 fI -
ylreporp ton yromem MMID
eruliaf yromem ro detresni
:speeb trohs 8 dna peeb gnol 1 fI -
detceted ton AGV
seY
seY
neercs TSOP ta tlaH
seY
OMC RL dna SC tser .tra
AMR tcatnoc ,liaf fI
seY
oN
eussi ecived larehpireP
.melborp DDH-
,rorre putes SOMC-
d .SOMCRLC ot een
ts ot liaf metsyS elbatsnu ro tra
a
es SOIB yfidom re
.gn
M SOC RLC tratser dna
hctiws USP no nruT
tekcos llaw ot tcennoc ro
.tratser dna
oN
h rotinom fi kcehC sa
sid
yalp
rotinom fi kcehC
yalpsid sah
Basic Troubleshooting Flowchart
67
68
Q77H2-TI USER MANUAL
Chapter 5
Memo
Loading...