Warnings and caution signs, illustrated below, are posted throughout this manual as well as on the
CD5000. They show safe and correct ways to handle the main unit to prevent personal injury to you,
others and to avoid property damage.
Before reading through the manual, take time to read through and learn the important information listed
in this section.
This "WARNING" sign indicates a situation in which incorrect
Warning
Caution
Please read all materials such as manuals and warranties that have come with the main unit.
Eclipse will not be liability for unsatisfactory main unit performance due to failure to follow these
instructions.
WARNING
● Do not modify this system for use other than that specified herein. Also, do not deviate
from the installation procedures described herein; Eclipse will not be held liable for
damages including, but not limited to serious injury, death or property damage resulting
from installations that enable unintended operation.
● This main unit requires 12V DC and should only be installed in a vehicle with a 12V negative
ground electrical system. Any other installation may cause a fire or other severe damage
to the main unit and the vehicle.
● Some main unit uses batteries. Never install main unit where young children can get
access to batteries. If a battery is swallowed, seek medical attention immediately.
● When the vehicle is in motion, never take your eyes off the road to make adjustments to the
main unit. You must pay attention to the road to avoid accidents, do not let the operation or
adjustment of the main unit distract you from proper vehicle operation.
● The driver should not look at the screen while driving. Accidents may result if you are not
paying attention to the forward direction.
● Do not put foreign objects in the loading slot of disc. Fires or shocks may result.
● Do not disassemble or alter this main unit. Accidents, fires or shocks may result.
● Do not let water, dust or foreign objects enter the internal parts of this main unit. Smoke,
fires or shocks may result.
● Pay attention to the location of the remote control. Traffic accidents or problems with
driving may result if the remote control makes its way under the foot pedals etc. When the
vehicle is in motion (Example: during stops, going around corners).
● Do not use when the main unit is malfunctioning (the screen is not lit or no sound comes
out). Accidents, fires or shocks may result.
handling or disregard of this sign may result in death or
serious personal injury.
This "CAUTION" sign indicates a situation in which incorrect
handling or disregard of this sign may result in personal injury
or may result solely in damage to property.
2
For your safety in using the CD5000
WARNING
● Always replace fuses with fuses of identical capacity and characteristics. Never use a
higher capacity fuse than the original. Using the wrong type of fuse may cause a fire or
severe damage.
● If foreign objects or water enters the main unit, smoke comes out, or there is a strange
odor, stop using it immediately, and contact your dealer. Accidents, fires, or shocks may
result if you continue to use it in these conditions.
● The driver should not change the CD while driving. As accidents may result if you are not
paying attention to the forward direction, first stop the car at a safe location and then
proceed.
● Plastic bags and wrappings may cause suffocation and death. Keep away from babies and
children. Never put bag over your head or mouth.
CAUTION
● When changing the installation location for this main unit, please consult the dealer where
you bought it for safety reasons. Expertise is necessary for removal and installation.
● Keep volume to a reasonable level so that you can hear sounds from outside the vehicle,
including warning sounds, voices, and sirens. Failure to do so may cause an accident.
● Be careful that hands and fingers are not pinched when adjusting the tilting angle or
closing display. Injuries may result.
● Do not put your hands or fingers into the loading slot of disc. Injuries may result.
● Do not touch the heat dissipating part of the amp. Burns may result from the heat of this
part.
● Do not recharge dry cell batteries. Dry cell batteries may rupture, resulting in injuries.
● Do not use batteries other than those specified. Also, do not mix old and new batteries.
Injuries or pollution to the surroundings may result from battery ruptures and leakage.
● When inserting batteries into the main unit, be careful with the polarity (positive/negative),
and insert them as indicated. If the battery polarities are incorrect, injuries and pollution to
the surroundings may result from battery ruptures and leakage.
● Replace used batteries as soon as possible; they may leak and damage main unit. Battery
leakage can burn your skin or your eyes. Wash hands after handling.
● If alkaline solution from alkaline dry cell batteries makes contact with your skin or clothes,
flush with clean water. If any of the solution gets in your eyes, also flush clean with water
and then seek medical attention.
● When disposing of lithium dry cell batteries, affix insulating tape to the positive and
negative terminals, and after they are insulated, dispose of them according to the "Local
municipal ordinances". Shorts, fires and ruptures may result from disposal when coming
contact with other electrically conductive objects such as metal parts, etc.
● Do not short, disassemble or heat the batteries, or place them in fire or water. Fire and
injuries may result from battery rupture and leakage.
● Store the remote control in a place away from direct sunlight, high temperatures, and high
moisture levels. The case may change shape, and the batteries may rupture and leak.
● Do not use this main unit except for in-vehicle use. Shocks or injuries may result.
I
3
Introduction
CAUTION
● Take notice of the volume position prior to turning ON the power. Hearing damage may
result if very loud noise is emitted when the power is turned ON.
● Do not operate under abnormal conditions such as when the sound is broken or distorted.
Fires may result.
● This main unit uses invisible laser light. Do not disassemble or alter this main unit. If
trouble occurs, contact the dealer where you bought the main unit.
Altering this main unit may cause exposure to laser emissions (worsening eyesight), or
result in accidents, fires or shocks.
● If the main unit is dropped or the cosmetics appear broken, turn off the power to the main
unit and contact your dealer. If used in this condition, fires or shocks may result.
4
Table of Contents
For your safety in using the CD5000 ........................................... 2
How to contact customer service....................................................... 92
9
Introduction
Operating precautions
<Your CD5000 will perform over a long period of time through correct handling and care.>
Notes on operation
• For your safety, play only at volume levels that allow outside sounds to be heard.
• It is recommended to use the logo shown on the left for this player.
• You can play music CDs(CD-R/CD-RW) on this player. Be sure to use
discs that have been properly processed.
Depending on the editing main unit used, some discs may not play
properly.
TEXT
• Do not insert anything other than a CD into this main unit.
Do not insert any foreign objects, such as coins or credit cards, into
the disc slot. Be especially watchful of children’s mischief in this
regard.
10
• Avoid severe mechanical shock.
When the player is subjected to severe vibration while traveling over a
rough surface, playback may be intermittent. When a situation like
this occurs, resume playback after returning to a smoother road.
• About dew condensation.
In cold or rainy weather, just as the interior glass surface gets fogged,
dew (water condensation) may also settle on the main unit. When this
occurs, disc playback may become intermittent or impossible.
Dehumidify the air in the vehicle for a while before resuming
playback.
• Cleaning the disc slot.
The disc slot tends to get dusty. Clean it occasionally to prevent
accumulated dust from scratching the discs.
Names of controls and parts
DCBA?8
Front view
1 23 45678
Names of controls and parts
II
III
E
No.ButtonName / Function
[CD (OPEN / EJECT)]
button
Opens/closes front panel and
ejects CD.
[AUDIO CONTROL] button
Adjusts volume and performs
other functions.
[DISC MS] button
Switches to DISC modes,
Memory Stick mode and AUX
mode.
[ILUM] button
Makes changes in illumination
color and switches title display.
[SOUND] button
Turns sound adjustment mode
and advance mode ON/OFF.
[FUNC] button
Turns function mode ON/OFF.
9
No.ButtonName / Function
[SEL] button
Selects radio stations and CD
tracks.
[ / ] button
Automatically finds radio
reception or fast-forwards/
rewinds.
[RTN] button
Returns to the previous screen.
[RESET] button
Resets this main unit functions
to default settings.
[DISP] button
Turns display adjustment mode
ON/OFF and switches screen
display.
11
Introduction
No.ButtonName / Function
Buttons [1] to [6]
Select radio preset channels
and perform disc mode
functions.
No.ButtonName / Function
[FM AM] button
Switches to radio mode and
switches radio bands.
[PWR] button
Turns the main unit power ON/
OFF.
[MUTE] button
Activates and deactivates
mute.
Double function button
➔ "MUTE" & "AREA SHOT"
functions
GF
No.Name / Function
Disc slot
Inserts a compact disc.
Memory Stick slot
Inserts and ejects a Memory Stick.
CAUTION
Never place or rest an object or your hands on the front panel.
12
Turning the power on and off
When the power is turned ON, the last source
mode (such as CD and tuner) used prior to
turning OFF the power will be restored.
When the vehicle has no ACC position on the
ignition switch, care is needed when turning off
the main unit. Follow Step 2 or Step 3 when
turning off the power.
When power is OFF, press the
1
[PWR] button.
The power will come ON.
ATTENTION
When the main unit's power is turned on for
the first time or if the battery terminals have
been disconnected because of vehicle
maintenance and the power is then turned
back on, the main unit will start up in FM1
mode. After this, the broadcast stations will
be searched for automatically and stored in
the buttons [1] to [6].
Names of controls and parts
III
When power is ON, press the
2
[PWR] button for less than two
seconds.
The power will go OFF and the main
unit will be in standby.
If you press the [PWR] button again for
more than one second, the power will
completely go OFF.
When power is ON, press the
3
[PWR] button for more than two
seconds.
The power will completely go OFF.
ATTENTION
If a car is not equipped with an ACC position,
press the [PWR] button for more than two
seconds.
13
Operation
How to operate the CD (MP3/WMA) player
About compact discs
• The information recorded on a compact disc is read by a laser beam, so nothing touches the disc
surface. A scratch on the recorded surface or a badly warped disc may cause deteriorated sound
quality or intermittent playback. Observe the following precautions to ensure high quality sound
performance:
• Do not leave an ejected disc in the disc slot for very long; the disc may
warp. Discs should be stored in their cases and kept away from high
temperature and humidity.
• Do not stick a piece of paper or tape on the disc. Do not write on or
scratch either side of a disc.
• Discs spin at a high speed inside the deck. Keep cracked or warped
discs out of the player to avoid damage to the main unit.
About brand new CDs
Rough Edges
Ballpoint pen
Rough Edges
Flakes
Recorded surface
14
• Avoid touching the recorded surface when handling a disc; handle
discs by their edges.
• You may notice that some brand new discs are rough around the
center hole or outside edge. Remove the rough edges with the side of
a ballpoint pen, etc. Rough edges may prevent proper loading in the
main unit. Flakes from the rough edges may also stick to the recorded
surface and interfere with playback.
How to operate the CD (MP3/WMA) player
About CD accessories
• Do not use accessories (stabilizers, protective seals, laser lens
cleaners, etc.) sold for "improving sound performance" or "protecting
CDs." The changes in CD thickness or outside dimensions made by
these accessories may cause problems in the player.
• Please be sure NOT to attach any ring-shape protector (or other
accessory) to your discs. Those protectors are commercially available
and said to protect disc and to improve sound quality (and antivibration
effect), but they can do more harm than good in regular uses. The most
common problems are disc insertion, disc ejections, and won't play
problems due to the protector ring that came off in the disc mechanism.
About borrowed CDs
• Do not use a CD with glue or remnants of adhesive tape or labels. They may cause the CD to get
stuck inside or damage the main unit.
How to remove CDs
• When removing the ejected disc, pull it straight out along the slot.
Pressing downward or lifting upward when removing a disc may
scratch the recorded surface of the disc.
N
O
OKAY
GOOD
IV
About irregularly-shaped CDs
• Specially-shaped CDs, like heart-shaped or octagonal CDs, cannot be
played. Do not attempt to play them, even with an adapter, since they
may damage the player.
•
About cleaning a CD
• Use a commercially available compact disc cleaner to clean a CD,
wiping gently from the center to the edge.
XXXX
XXXX
XXXX
• Do not use benzine, thinner, LP record spray or other cleaners on
CDs. They may damage a CD’s finish.
15
Operation
About MP3/WMA
ATTENTION
The making of MP3/WMA files by recording from sources such as broadcasts, records, recordings, videos and
live performances without permission from the copyright holder for uses other than personal enjoyment is
prohibited.
What is MP3/WMA?
MP3/WMA (MPEG Audio Layer III) is a standard format for audio compression technology. By using
MP3/WMA a file can be compressed to one-tenth the size of the original.
WMA (Windows Media
compressed to a size smaller than MP3 files.
This main unit has limitations on MP3/WMA file standards and recorded media and formats that can
be used.
*Supports VBR (48~192 kbps).
*Does not support lossless compression.
*Does not support WMA files recorded at a frequency of 48kHz with a bit rate
of 48kbps.
ID3/WMA tag
MP3/WMA files have an "ID3 / WMA Tag" that allows input of information so that data such as song
title and artist can be saved.
This main unit supports ID3v. 1.0, 1.1 and WMA tags.
16
How to operate the CD (MP3/WMA) player
Media
Media capable of playing MP3/WMA includes CD-R and CD-RW discs. Compared to CD-ROM
media commonly used for music discs, CD-R and CD-RW discs are fragile in high temperature/high
humidity environments and one section of the CD-R and CD-RW may become incapable of
playback. Fingerprints or scratches on the disc may prevent playback or cause skipping during
playback. Sections of a CD-R and CD-RW may deteriorate if left inside a vehicle for long periods of
time. It is also recommended that CD-R and CD-RW discs are kept in a light-blocking case because
the discs are vulnerable to ultra-violet light.
Format of discs
The format of discs to be used must be ISO9660 Level 1 or Level 2.
Control items for this standard are as follows:
• Maximum directory layers:8 layers
• Maximum characters for folder names/file names:32 (including "." and 3 letter file extension)
•
Allowable characters for folder names/file names:
•
Number of files/folders possible on a single disc: 999
[Configuration example for CD supporting MP3/WMA]
Root directory (F1)
F2
Folder 2
001.mp3
002.mp3
003.mp3
004.txt
005.mp3
F158
F159
F255
Folder 158
Folder 159
001.mp3
002.mp3
Folder 255
Number of files/folders possible on a single disc is 999.
Files aside from MP3/WMA files (Example: 004.txt) also count as single files.
• Total number of folders possible on a single disc:255
• Maximum folders this main unit can recognize: 256*
*: A root directory is counted as one folder.
A~Z, 0~9, _ (underscore)
IV
File names
Only files with the MP3/WMA file extension ".mp3", ".wma" can be recognized as MP3/WMA and played.
Be sure to save MP3 files with the ".mp3" file extension. Be sure to WMA files with the ".wma" file
extension. The "MP" letters of the file extension will be recognized whether entered as uppercase letters
or lowercase letters.
CAUTION
If the ".mp3", ".wma" file extension is attached to a file other than an MP3/WMA file, that file will be
mistakenly recognized by this main unit as an MP3/WMA file and played, resulting in loud noise
output that can damage the speakers. Be sure to avoid attaching the ".mp3", ".wma" file extension
to files that are not MP3/WMA files.
17
Operation
Multi-sessions
Multi-sessions are supported, and playing of CD-R and CD-RW discs with annotated MP3/WMA
files is possible. However, when "Track at once" has been written, close the session or process the
warning message. Standardize the format of each session without changing the format.
Playing MP3/WMA
When a disc with recorded MP3/WMA files is inserted, the main unit first checks all the files on the disc. No
sound is output while the main unit is checking the files on the disc. It is recommended that the disc be recorded
without files other than MP3/WMA files and without unnecessary folders in order to speed up the checking of
disc files by the main unit.
MP3/WMA playing time display
It is possible that playing time will not be correct, depending on the writing condition of the MP3/
WMA file.
*It is possible that playing time will not be correct when VBR Fast Up/Down is operated.
Display order of MP3/WMA file/folder names
Names of MP3/WMA folders and files within the same level are displayed in the following order.
1.MP3/WMA folders displayed first, by ascending order of numbers, letters.
2.Files displayed next, by ascending order of numbers, letters.
18
How to operate the CD (MP3/WMA) player
Listening to CD (MP3/WMA file)
Press the [CD] button for less
1
than one second.
The front panel opens.
If a disc has already been loaded, the
disc is ejected by pressing the [CD]
button.
Insert a CD into the disc slot, label
2
side up.
The CD will immediately start playing.
ATTENTION
When a CD is already loaded, press the
[DISC] button to switch to the CD mode.
● Note ●
• When music data recorded in
the normal way (CD-DA) is
present on the same disc as
MP3/WMA music files, the
music data recorded normally
will be played. To listen to the
MP3/WMA music files, press
the button [3] for more than one
second.
• When a non-MP3/WMA file is
played, "NO SUPPORT" will
appear.
• The optional CD changer
cannot be used to play MP3/
WMA files.
Switching to the CD player
mode
First press the [DISC] button for less than one
second to switch to the disc mode. It is assumed
here that a CD has already been loaded into the
main unit.
Press the [DISC] button for less
1
than one second to switch to the
CD player mode.
This starts CD play.
If an external CD changer and an
optional iPod interface adaptor (iPC-
106) are connected, each additional
press of the [DISC] button will switch
modes from CD player
1 ➔ CD changer 2 ➔ iPod ➔ CD
player.
A changer or player with no discs
loaded will be skipped.
ATTENTION
• Playback may be intermittent when there is
a scratch on a CD or when the recorded
side is dirty.
• Only two external CD changers may be
connected.
➔ CD changer
IV
CAUTION
Do not press the [
being inserted. This could cause an injury
and damage to the front panel.
CD
] button while CD is
19
Operation
TRACK (FILE) UP / DOWN
Media
CD
MP3
WMA
Turn the button.
Turn to the right : Advances to the next track (file).
Turn to the left : Returns to the beginning of the track (file) being played. Repeat
turning for the previous tracks (files).
Operation
Fast Forward/Rewind
Media
Operation
Press and hold the button.
CD
MP3
WMA
: Fast forward.
: Rewind.
SCAN / REPEAT / RANDOM
Media
Operation
Press the button.
CD
: Playing the beginning of tracks.
: Repeating the same track.To cancel, press the button again.
: Playing tracks in random order. To cancel, press the button again.
On pressing the button for less than one second.
MP3
WMA
: Just the first 10 seconds of each file in the folder played currently are played in
sequence.
: Repeating the same file. To cancel, press the button again.
: A file is selected from all the files in the folder played currently and played.
ATTENTION
• To continue playing a desired track, press the button again to stop scanning.
• After the entire disc is scanned once, ordinary playback starts from the point where scanning
started.
20
How to operate the CD (MP3/WMA) player
FOLDER UP / DOWN
Media
Operation
Press the button.
MP3
WMA
: Selects the next folder.
: Selects the previous folder.
FOLDER SCAN / FOLDER REPEAT / ALL RANDOM
Media
Operation
On pressing the button for longer than one second.
MP3
WMA
: Just the first 10 seconds of the first song in each folder are played.
: All the files in the same layer as the folder being played are repeated. To cancel,
press the button again.
: The files in all the folders are played randomly. To cancel, press the button again.
ATTENTION
• During random playback, press the [5 RPT] button to repeat the track being played. To cancel
repeat play (go back to random play), press the [5 RPT] button again. During playback of a
particular track: The track being played is played repeatedly.
• Occasionally the same track happens to be played (selected) two or more times in a row; this
is normal operation and is not a sign of a problem.
• When any of the functions -" REPEAT " and " RANDOM " - is selected, a message such as
[RPA] or [RAND] appears on the display to verify the current function.
IV
21
Operation
Return to the root directory of
the CD (MP3/WMA file)
In the root directory, when a file cannot replay,
the system will return to the first file that can
perform a replay. (In the configuration example,
the file is returning to 001.mp3. see page 17.)
Press the [RTN] button.
1
Displaying CD text
Only this CD player supports CD TEXT. It can not
be displayed with the optional CD changer. If the
CD came with a logo shown below, it is recorded
with a disc title and track titles. This information
will be displayed during playback.
Press the [ILUM] button for more
1
than one second.
Pressing the [ILUM] button while text
is displayed scrolls the display in the
order DISC title ➔ TRACK title, and
then the display stops with the TRACK
title.
CD TEXT recorded with characters
other than alphanumeric and symbols
cannot be displayed.
Displaying title (MP3/WMA file)
Press the [ILUM] button for more
1
than one second.
Each time the button is pressed, the
following will be displayed in order.
Folder Name/File Name* ➔ Folder No.
/File No. ➔ Tag
*:The display area shows a
maximum of 14 characters and then
scrolls to display the remaining
characters.
After the folder name is displayed,
the file name will be displayed by
scrolling. After the file name is
scrolled, the display will be fixed.
ATTENTION
Folder name/file name or tag recorded with
characters other than alphanumeric and
symbols cannot be displayed.
Ejecting the disc
Press the [CD] button for less
1
than one second.
The front panel opens and the disc is
ejected.
Remove the disc and press the
2
[CD] button.
The front panel closes.
22
CAUTION
• Do not drive with the front panel open.
The panel may cause unexpected
personal injury during a panic stop or
abrupt changes of vehicle motion.
• Do not attempt to close the front panel
with your hands. Doing so may damage
the panel.
How to operate the Memory Stick player
How to operate the Memory Stick player
About Memory Sticks
• Do not store Memory Sticks in places that are subject to static electricity
and electrical interference, otherwise the data they contain may become
corrupted.
• In order to protect the player, the player's functions will be stopped
automatically if a problem occurs. If the player cannot be operated even
after following the instructions that appear on the screen, the main unit is
malfunctioning, and you should ask the place of purchase for further
advice.
• If using a Memory Stick Duo, you will need to use it with a Memory Stick
Duo adapter.
• Only Memory Sticks with a capacity of up to 128 MB can be used in the
main unit.
• Memory Stick PRO types of Memory Stick cannot be used.
• If MG Memory Stick is not being used for prolonged time, remove it from
the main unit.
• MG Memory Sticks bearing one of the marks at the left can be used.
• Memory Sticks bearing one of the marks at left can be used for writing and
reading data other than music data.
MagicGate Memory Stick and Memory Stick are
trademarks of Sony Corporation.
• If the write protection switch on a MG Memory Stick or Memory Stick is at
the lock position, other data cannot be saved on it.
• Do not remove a MG Memory Stick while it is being accessed for
playback, otherwise the data on the MG Memory Stick may become
corrupted. If the data becomes corrupted, it can no longer be retrieved.
• Please format the MG Memory Stick on this main unit. A MG Memory
Stick formatted by another main unit may not be used for playing back or
recording data.
• When a Memory Stick is formatted, all the data on that Memory Stick will
be erased (Includes Memory Stick security recorded data and sound
quality data).
• MG Memory Stick must be formatted prior to use. Refer to "Formatting
MG Memory Stick (quick format)" on page 27 for instructions on formatting
MG Memory Sticks.
• It may not be possible to use MG Memory Sticks that have just been
purchased. If this happens, use the unit to format the MG Memory Stick.
Refer to "Formatting MG Memory Stick (quick format)" on page 27 for
instructions on formatting MG Memory Sticks.
• Some recordings and other data may not be played back or written/read,
depending on the device that was used to save the data.
IV
V
23
Operation
N
• Do not use Memory Sticks with labels that are peeling off or that have
name tags (labels) attached.
• Store Memory Sticks in places away from direct sunlight and high
humidity, otherwise the Memory Sticks may become unusable.
• Place Memory Sticks in their protective cases during transportation and
storage.
• Do not touch the terminals with your hands or with metallic objects.
• When removing the ejected Memory Stick, pull it straight out along the
slot. Pressing downward in the process may scratch the recorded surface
OKAY
O
G
O
O
D
of the Memory Stick.
About cleaning the Memory Sticks
• In order to maintain good audio performance from Memory Sticks,
periodically wipe the cartridge clean of any dust and other contamination
with a dry cloth.
24
How to operate the Memory Stick player
Listening to MG Memory Stick
Press the [CD] button for more
1
than one second.
The front panel opens.
Insert a MG Memory Stick into the
2
Memory Stick slot.
ATTENTION
• If you press the [CD ] button less than
one second while you are listening to the
CD, the disc is ejected. To insert/eject the
MG Memory Stick, press the [CD] button
for more than one second and open the
front panel.
• Insert the MG Memory Stick with the mark
facing inwards and press MG Memory Stick
into place until a clicking sound is heard. Do
not press forcefully when the MG Memory
Stick makes contact with the internal
stopper because it cannot be inserted any
further. (The MG Memory Stick should be
protruding a few millimeters from the
Memory Stick slot.)
• Use a Memory Stick Duo adapter when
inserting the Memory Stick Duo. (If the
Memory Stick Duo is inserted without the
adapter, it will not be ejected from the main
unit.)
• When the MG Memory Stick is already
loaded, press the [DISC MS] button to
switch to the Memory Stick mode.
Switching to the Memory Stick
player mode
Music data recorded on "MG Memory Stick" with
ATRAC3 (an audio compression technology) can
be played on this main unit. The following
explanation of the operation is made assuming
that the MG Memory Stick has already been
inserted.
First press the [DISC MS] button for less than
one second to switch to the disc mode. It is
assumed here that a MG Memory Stick has
already been loaded into the main unit.
ATTENTION
• Artist name and music title (track
titles) can be displayed when they
are recorded on the MG Memory
Stick. A maximum of 14 characters
(1 byte alphabets, numeric or
symbols) can be displayed.
• Music data recorded with MP3/WMA
and ATRAC3 Plus cannot be played.
Press the [DISC MS] button for less
1
than one second to switch to the
Memory Stick player mode.
Advancing to the next track or
returning to the beginning of
the track being played
V
CAUTION
Do not press the [
MG Memory Stick is being inserted. This
could cause an injury and damage to the
front panel.
Press the [CD] button for less
3
than one second.
The front panel closes.
Press the [DISC MS] button to
4
switch to the Memory Stick mode.
MG Memory Stick will start playing.
CD
] button while the
Turn the [SEL] button to the left or
1
right.
Turn to the right:
Advances to the next track.
Turn to the left:
Returns to the beginning of the track
being played.
the previous tracks.)
(Repeat turning for
25
Operation
Fast Forward/Rewind
Fast forward or rewind the song being
played currently.
Press and hold the [] or
1
[]button.
[] button: Fast forwards.
[] button: Rewinds.
Playing the beginning of tracks
(SCAN)
Press the [4 SCAN] button.
1
Pressing the button causes the player
to move up to the next track and play it
for 10 seconds, then move up to the
next track and play it for 10 seconds,
and so on until the button is pressed
again.
ATTENTION
To continue playing a desired track, press the
button again to stop scanning.
After the entire disc is scanned once, ordinary
playback starts from the point where scanning
started.
Playing tracks in random order
(RANDOM)
Press the [6 RAND] button to play
1
the tracks in random order.
To cancel, press the [6 RAND]
button again.
ATTENTION
• During random playback, press the [5 RPT]
button to repeat the track being played. To
cancel repeat play (go back to random
play), press the [5 RPT] button again.
During playback of a particular track: The
track being played is played repeatedly.
While searching for : The following track is
played repeatedly.
• Occasionally the same track happens to be
played (selected) two or more times in a
row; this is normal operation and is not a
sign of a problem.
• When any of the functions - "Playing the
beginning of tracks", "Repeating the same
track" and "Playing tracks in random order"is selected, a message such as [SCAN],
[REPEAT] or [RANDOM] appears on the
display to verify the current function.
Repeating the same track
(REPEAT)
Press the [5 RPT] button to repeat
1
the track being played.
To cancel, press the [5 RPT] button
again.
26
How to operate the Memory Stick player
Formatting MG Memory Stick
(quick format)
MG Memory Stick can be formatted.
Press the [FUNC] button.
1
The function mode is activated.
Turn the [SEL] button to select
2
Memory Stick.
The selection item is highlighted.
Press the [SEL] button.
3
The Memory Stick setting mode is
activated.
The format mode is activated, then
[OK?] message will appear.
Press the [SEL] button for more
4
than two seconds.
MG Memory Stick will be formatted.
Press the [RTN] button.
5
At this time, other adjustments can
also be made in Memory Stick
setting mode.
Ejecting the Memory Stick
Press the [CD] button for more
1
than one second.
The front panel opens.
Eject the Memory Stick.
2
Lightly press the Memory Stick once.
ATTENTION
The Memory Stick will not eject by itself. Lightly
press the Memory Stick to eject.
CAUTION
• Do not drive with the front panel open.
The panel may cause unexpected
personal injury during a panic stop or
abrupt changes of the vehicle motion.
• Do not attempt to close the front panel
with your hand. Doing so may damage
the panel.
Press the [CD] button for less
3
than one second.
The front panel closes.
V
Press the [RTN] button.
6
At this time, other adjustments can
also be made in function mode.
Press the [FUNC] or [RTN] button
7
to exit function mode.
ATTENTION
Do not turn off the power or the ignition switch
while formatting. The formatting process will
be interrupted and the data may be corrupted.
27
Operation
How to operate the tuner
ATTENTION
• If stations have been stored in memory,
pressing the stored button from [1] to [6] will
directly select a station. (Refer to "Manually
setting stations into memory" on page 29)
CAUTION
If the vehicle’s battery is disconnected (for
repairs to the vehicle or for removing the
main unit), all the stations in memory will be
lost. In such a case, set stations in the
memory again.
Tuning to a station
First, press the [FM AM] button to start tuner
operation.
There are automatic and manual methods for
setting stations in memory. The main unit will
accept up to 24 stations in memory: 6 in AM 18 in
FM (6 each for FM1, FM2 and FM3). (Initial
setting)
Press the [FM AM] button for less
1
than one second to switch to the
desired FM, AM bands.
Radio bands will switch from FM1 ➔
FM2 ➔ FM3 ➔ AM in order each time
the button is pressed.
Press the [] or [] button to
3
start the automatic station search.
button:
[]
Starts searching for higher
frequencies.
[] button:
Starts searching for lower
frequencies.
ATTENTION
At times, it may be difficult to maintain optimum
reception because the antenna affixed to your
vehicle is in motion constantly (relative to the
broadcast antenna), encountering continuous
variation in the received radio signals’ strength.
Other factors affecting reception include
interference from natural obstacles, sign posts,
etc.
When an optional HD Radio tuner unit is
connected, digital broadcasts have reception
priority. (U.S.A. only)
Turn the [SEL] button to the left or
2
right to tune to a station.
Turn to the right:
Tunes to higher frequencies.
Turn to the left:
Tunes to lower frequencies.
28
How to operate the tuner
Entering stations into memory
automatically
(The automatic preset mode:
ASM)
Press the [SEL] button for more
1
than two seconds until a beep is
heard.
The automatic preset mode starts.
The [ASM ON] indicator on the screen
flashes, and stations are automatically
entered in memory under the buttons
[1] to [6].
These buttons are called the preset
buttons.
ATTENTION
• Pressing the preset buttons ([1] to [6])
allows you to make one-touch station
selections. The frequency of the selected
station is indicated on the display.
• When a new station is set in memory, the
station previously set in memory will be
deleted.
• If there are less than six receivable
stations, the stations set in the remaining
buttons will be retained.
Manually setting stations into
memory
This section covers the setting of stations in
memory under the numbered buttons.
Turn the [SEL] button to the right
1
or left to tune to the station to be
entered in memory.
Select any button, from [1] to [6],
2
and press it for more than two
seconds.
The station to which you have tuned
is now memorized and set in the
selected button.
Repeat the procedure to set the
stations to which you have manually
tuned in addition in memory, in turn,
for the buttons [1] to [6]. These
buttons are called the preset
buttons.
Preset station scan
This function enables reception of all the stations
in the preset buttons for five seconds each.
Press the [SEL] button for less
1
than two seconds.
[P SCAN] will appear on the display,
and stations stored under the preset
buttons [1] to [6] will be played for
five seconds each.
VI
To stop the preset scan mode at a
2
desired station, press the [SEL]
button again.
The main unit will stay tuned to the
desired station.
29
Operation
Changing the reception
sensitivity for automatic
scanning
The main unit lets you select the reception
sensitivity to be used for automatic scanning of
stations. The two sensitivity modes available for
this main unit are LOC mode and DX mode.
During automatic scanning, the
reception sensitivity switches
automatically to one of two levels.
Initially the reception sensitivity is
set to the low level so that only
LOC Mode
DX Mode
ATTENTION
When an optional HD Radio tuner is
connected, reception sensitivity is set to the
LOC Mode. The DX Mode is unavailable.
(U.S.A. only)
1
2
stations with strong signals are
received. If no stations could be
received, the reception sensitivity is
increased so that stations with
weaker signals can also be
received.
Because the reception sensitivity for
automatic scanning is set to the high
level from the start, even stations
with weaker signals can be received.
(Signal crossover may result in
some stations being hard to hear.)
Check that the main unit is in
standby mode.
Press and hold the button [1], then
the [FM AM] button, and hold both
for more than three seconds.
The mode switches between LOC
mode and DX mode each time the
buttons are pressed.
Changing the radio band
location
The location for the radio bands used between
the North American region and the Asia/
Australia/Latin region can be switched. The
default setting is USA (North America).
ATTENTION
When an optional HD Radio tuner is
connected, radio band location is set to USA.
Other radio band locations are unavailable.
(U.S.A. only)
Check that the main unit is in
1
standby mode.
Press and hold the button [3], then
2
the [FM AM] button, and hold both
for more than three seconds.
The radio band switches in the order
shown below each time the buttons
are pressed.
USA ➔ ASIA ➔ AUS ➔ LATIN
➔ USA www
After this, the broadcast stations will
be searched for automatically and
stored in the buttons [1] to [6].
30
Loading...
+ 263 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.