We appreciate your purchase of this receiver.
Please read through this manual for correct operation.
We suggest that after reading it you keep this manual
in a safe place for future reference.
Warnings and cautions signs, illustrated below, are posted throughout this manual as well as
on the device itself. They show safe and correct ways to handle the product so as to prevent
personal injury to you and others, and to avoid damage to property. Before reading through
the manual, take time to read through and learn the important information listed in this section.
Cautions for use
* The images appearing on the screen may differ from those shown in this manual
depending on the type of database used and when it was created.
This sign indicates a situation in which incorrect handling
Warning
Caution
The symbol shown below indicates important instructions or helpful information to keep in
mind.
A point it will be helpful to remember.
Important points.
through disregard of a sign might result in death or serious
personal injury.
This sign indicates a situation in which incorrect handling
through disregard of a sign might result in personal injury or may
result solely in damage to property.
● Please read all materials that come with the product, such as manuals and warranties.
Fujitsu Ten will not be responsible for unsatisfactory product performance due to failure to
follow these instructions.
● Changes in product specifications may result in differences between the content of the
manual and actual product features.
Please use care in handling the manual.
Forcefully spreading or pulling on pages may result in their falling out of the binding.
Use the manual carefully.
1
Page 3
Table of Contents
Introduction
How to use this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The Topic Index simplifies searches for explanations about
individual features. When confused by an operation, use the Topic
Index to search for information about the operation.
Page 12
11
Page 13
Introduction
1. How to use this manual
Item title
A number and
title is assigned
to each item.
Detailed operation
title
A title is assigned to
each detailed
operation.
Operation title
A title is assigned
to each operation.
Operation
procedure
Describes the
operation.
Proceed with the
operation according
to the numerical
order.
Section title
A title is assigned to each section.
Attention
Additional points
regarding operation
are given here.
12
Page 14
Section side
heading
The side heading for
the current section.
Introduction
Operation screen
A screen showing
the operation.
Continue to the next
page
Indicates that
operation procedures
continue on the next
page.
13
Page 15
Introduction
2. Features
MUSIC JUKE for recording music (Page 67)
With MUSIC JUKE, which employs a highcapacity hard disc, you can record voice or
music output from any of the audio modes.
Aside from being able to search for recorded
data by type, the Edit function also allows you
to create your own private album.
DVD player with sharp video and dynamic sound
(Page 109)
Plays DVD videos recorded with high image
and sound quality.
(DVD media is able to record a movie with high
quality video and digital sound that exceeds
the quality of CD media.)
MP3 player that plays back the equivalent of several albums
of music recorded on a single music disc (Page 52)
MP3 audio compression technology
compresses audio data to one-tenth the
original size. CD-R/RW with recorded MP3s
can be played.
14
Page 16
DSP effects for simulating acoustics of various
performance environments (Page 31)
Provides ability to simulate the sensation of
various performance environments for
matching to the genre and source of a song.
Memory Stick player for playing music downloaded
from a computer (Page 61)
Supports ATRAC3 audio compression
technology which combines high sound quality
with a high compression rate. Audio files
downloaded to the MG Memory Stick from
computers or mobile phones can be played.
Selection and display of favorite wallpaper (screen
backgrounds) (Page 38)
Introduction
Wallpaper of your choice can be switched and
displayed for use as the background of the
information screen and audio operation
screens.
The screen from a navigation unit can also be
linked and selected.
●Setting wallpaper for the information screen and
audio operation screens
15
Page 17
Introduction
Features
System upgrade
● CD changer(Page 64)
A CD changer enables non-stop playing of
multiple discs, for convenience at times such
as taking a long drive.
It is easy to search for and play a song from
among the discs on a changer.
● VTR (Page 132)
Videos can be watched if a VTR deck is
connected.
16
Page 18
Introduction
3. Before using the deck
● Be very careful and pay close attention to safety when
operating the audio controls while driving, otherwise
accidents may occur. Also be sure to set the volume so
that you can still adequately hear sounds outside the
vehicle.
Otherwise damage may occur.
● Never continue to use the system if it is malfunctioning in
any way. If smoke, abnormal noises or abnormal odors
are noticed, turn off the power immediately.
Immediately turn off audio in such situations.
● Exercise caution as to the temperature inside the vehicle.
The temperature inside the vehicle can increase during
hot weather. Wait for the temperature inside the vehicle to
drop before using the unit.
Otherwise damage may occur.
Introduction
● Drivers should not operate the DVD while driving. Also be
sure to set volume so that you can still adequately hear
sounds outside the vehicle.
Otherwise damage may occur.
● Do not disassemble or modify the deck.
The deck has a precisely designed structure, so contact
the store of purchase in the event of any unsatisfactory
performance.
Continue to the next page
17
Page 19
Introduction
Before using the deck
● Do not apply excessive force to the monitor, or damage
may occur.
● Do not place items such as cups or cans on top of the
monitor, and do not leave the monitor tilted down when
not in use.
Otherwise damage may occur.
● Do not insert any objects other than discs or Memory
Sticks into the slot.
Otherwise damage may occur.
18
● Be careful not to get fingers or other objects caught in the
monitor when it is being retracted into place.
Interference can cause an injury or damage the deck.
● When removing a disc or Memory Stick from the deck, do
so in a horizontal direction.
Do not pull them up forcibly or press down on them
strongly while removing them.
Removing improperly can scratch the disc, cause deck
noise or damage the Memory Stick.
Page 20
About discs
●Water droplets (condensation) can form on the inside of the unit during cold or
rainy weather in the same way car windows can fog up. When this happens, the
audio can jump and playback can stop, so ventilate or dehumidify the vehicle for
a short time before operating the equipment.
●To safeguard the components of the player, the unit will automatically stop when
a malfunction occurs. If the player will not operate even when messages
displayed on the screen are followed, it is possible that the unit has been
damaged. Contact the store of purchase.
●It is possible that the sound will skip if the vehicle experiences violent motion on
rough roads.
About supported disc types
●An audio or DVD video disc bearing one of the marks shown below can be
played. Only DVD-R/RW (DVD-Recordable/ReWritable) and DVD+R/RW
(DVD+Recordable/ReWritable) discs recorded in Video mode can be played.
Discs recorded in Video mode (VR) cannot be played.
●Supports Dolby Digital. Discs bearing the following mark can be used.
Introduction
Manufactured under license from Dolby Laboratories, Inc. Dolby and the double-D symbol are
registered trademarks of Dolby Laboratories.
●It is possible that a CD-R (CD-Recordable) or CD-RW (CD-ReWritable) disc will
not play on the unit due to special disc characteristics, scratches, dirt or
deterioration caused by long storage in the vehicle. In addition, an unfinalized
CD-R or CD-RW disc written in CD-R, CD-RW or UDF format will not play on the
unit.
●It is possible that a DVD-R/RW (DVD-Recordable/ReWritable) or DVD+R/RW
(DVD+Recordable/ReWritable) disc will not play on the unit due to special disc
characteristics, scratches, or dirt or deterioration caused by long storage in the
vehicle. In addition, an unfinalized DVD-R or DVD-RW disc will not play on the
unit. It is possible that discs recorded using a computer may not play on the unit
depending on the environment and/or settings of applications.
●The CD-TEXT function requires commercially available CDs which support
CD-TEXT. It is possible that characters in CD-R and CD-RW data may not be
displayed correctly.
●Do not use discs with transparent or semi-transparent portions within the
recording area, or C-thru discs, since they may not be accepted and ejected
properly and may not play properly.
Continue to the next page
19
Page 21
Introduction
Before using the deck
●
Super Audio CDs can only be played in the hybrid disc layer.
●CCCDs (Copy Control CD) do not conform to official CD
standards and so are not supported.
●CD-EXTRA discs can be played as audio CDs.
●Voice tracks on Mixed Mode CDs cannot be played. Only
music tracks will be played.
●Video-CDs cannot be played.
About handling discs
● Be sure to store discs in their cases and keep them out of
direct sunlight. Discs can warp and become unusable.
● Do not apply paper-based tape to either the recording
side or label side of a disc. Otherwise damage may occur.
20
● Do not use discs on which there are cracks or large
warps. Otherwise damage may occur.
● Do not touch the recorded side of a disc when handling it.
(Iridescent side of the CD) The disc may become dirty
causing jumping to occur.
● Using a disc that has become dirty can scratch the disc
and result in sound jumping. Use a commercially available
compact disc cleaner to clean the CD, wiping lightly from
the center to the edge.
Page 22
Rough Edges
Ballpoint pen
About new discs
● You may notice that some brand new discs are rough
around the center hole or outside edge. Remove the
rough edges with the side of a ballpoint pen, etc. Rough
edges may prevent proper loading in the unit. Flakes from
the rough edges may also stick to the recorded surface
and interfere with playback.
About rental discs
Introduction
Recorded surface
Flakes
CD stabilizer ring
● Do not use CD discs with attached cellophane tape, rental
CD discs with glue protruding from labels or discs with the
residue of peeled adhesives. Using discs with those
conditions can prevent the player from properly opening
and closing as well as cause other damage.
About specially shaped discs
● Specially-shaped CDs cannot be played. Do not attempt
to play them, even with an adapter, since they may
damage the player.
● Please do not use a commercially available lens cleaner
because it may cause damage to the pickup of the player.
About disc accessories
● Do not use accessories (stabilizers, protective seals, laser
lens cleaners, etc.) sold for "improving sound
performance" or "protecting CDs." The changes in CD
thickness or outside dimensions made by these
accessories may cause problems in the player.
● Do NOT attach any ring-shape protector (or other
accessory) to your discs. Those protectors are
commercially available and said to protect discs and to
improve sound quality (and anti vibration effect), but they
can do more harm than good during regular use. The
most common problems are insert/eject related problems
and "No playback" problems due to the protector ring
coming off in the disc mechanism.
21
Page 23
Introduction
Before using the deck
About the Memory Stick
●Do not leave the Memory Stick in places exposed to static electricity or electrical
noise. Otherwise, data may be lost.
●To safeguard the components of the player, the unit will automatically stop when
a malfunction occurs. If the player will not operate even when messages
displayed on the screen are followed, it is possible that the unit has been
damaged. Contact the store of purchase.
●
After playback or uploading of data to the hard drive is complete, promptly remove
the MG Memory Stick.
●
Do not remove the Memory Stick while it is being used to upload data to the hard
drive or playback data. Otherwise, data may be lost. Please be aware that we will not
be held responsible for lost data.
About supported Memory Stick types
●Memory Sticks with a capacity of up to 128MB are supported.
●The Memory Stick Duo must be used with the Memory Stick Duo Adapter.
●Memory Stick PRO is not supported.
●MG Memory Sticks labeled with the following marks can be used with this device.
●MG Memory Sticks labeled with the following marks can only be used when
registering a pass code in database update or Eclipse Security Network (ESN).
22
MagicGate Memory Stick and Memory Stick are registered trademarks of Sony
Corporation.
●Use the dedicated device to format (initialize) the MG Memory Stick. The
Memory Stick cannot be used on this unit if it has been formatted using a device
other than the dedicated device.
Page 24
About handling the Memory Stick
●
In order to maintain a
high quality sound,
regularly wipe clean any
dust or dirt from the
surface of the cartridge
with a dry cloth.
●
Do not use Memory Sticks
with tape or peeling labels.
● Store in a dry place, out
of direct sunlight.
Otherwise, it may
become impossible to
use the Memory Stick.
Introduction
●Always place in the
case provided when
transporting or storing.
● Do not touch terminals
with metal objects or
your bare hands.
About the LCD panel
●The LCD panel can appear to be white or black when seen from certain angles.
●The screen will be difficult to read when external light such as sunlight falls on
the display.
23
Page 25
Basic operation
1. Switching modes
The deck can be used when the vehicle's ignition switch is on or in the ACC position.
● This deck supports use of a remote control. The card remote control is sold separately and
can be purchased at your local retailer. See page 134 for instructions on operation of the
remote control.
Switching the mode
Press .
SOURCE MENU
Touch the touch switch for an audio
mode and the relevant mode will
be displayed on the screen.
●On-screen display
Displaying operation screen
Press .
AUDIO CONT
24
Page 26
Switching source using touch switches
Touch the SOURCE MENU
RECALL switch (indicated at right)
in the audio or DVD/VTR operation
screen.
When the SOURCE MENU switch
is touched, the operation screen for
the selected source is displayed.
● Touch to return to the original
screen.
SOURCE MENU RECALL switch
Basic
operation
25
Page 27
Basic operation
●AM
●FM
2. Operation screen of each mode
The operation screen for each mode will appear as shown below.
radio operation screen
radio operation screen
●CD player operation screen●MP3 player operation screen
●Memory Stick player operation screen●MUSIC JUKE operation screen
●DVD player operation screen
●CD changer operation screen (optional)
●VTR operation screen
When the operation screen for the DVD or VTR has not been operated for 6 seconds or more,
it will automatically be canceled.
26
Page 28
Basic operation
3. Adjusting the volume
Adjusting the main volume
Press the VOLUME button.
● Adjustment levels from 0 to 80 are
available.
(up) : Volume UP (louder)
(down) : Volume DOWN (quieter)
Setting the BEEP tone
The guide tone that is emitted when touching a panel switch or touch switch can be set.
VOLUME button
Basic
operation
Touch in the
SETTING
INFORMATION screen.
Touch , , ,
1234
OFF
, or
for GUIDE TONE.
● The selected touch switch will turn
green.
● Touch to cancel (turn off) the
To u ch .
OFF
guide tone.
ENTER
●Set the volume at a level which will not adversely affect your safety while driving.
●The volume level may change after switching sources. Adjust the volume to
match the source being used.
●If the volume is adjusting during DVD playback, this adjusted volume can be
saved as the volume level for the DVD player.
●A volume adjustment made during DVD playback will not affect other sources.
The volume will return to the level set for the source used prior to the DVD.
27
Page 29
Basic operation
4. Adjusting sound quality
By adjusting the DSP settings, equalizer, and the volume balance you can simulate a favored
sound environment within the vehicle.
Sound quality can be adjusted in all audio operation screens as well as in the information
screen.
Displaying the sound adjustment screen
From an operation screen
Touch in the VTR operation
SET
screen, or in the DVD operation
screen followed by to display the
SET
switch for sound quality adjustment.
From the information screen
Press , then touch .
INFOSETTING
28
Page 30
The following settings/adjustments can be made in operation screens and setting
screens.
Touch switch/itemFunctionPage
DSP
EQ
It is possible to recreate acoustics (concert hall) that match
the music genre or source you are going to play.
Each factory set equalizer curve can be adjusted to create
a customized curve.
Circle surround can easily be simulated using the existing
Circle Surround II
speaker system in your vehicle (when the vehicle has 4
speakers).
Sound localization can be adjusted according to the
POS
number and position of passengers in order to obtain
optimum acoustic effects.
FADER BALANCE
LOUDNESS
The left/right/front/rear balance can be adjusted.
It is possible to emphasize bass/treble when listening at
low volume.
It is possible to set the harmonizer level so that
HARMONIZER
compressed data is played back with a sound quality
corrected to a level as close as possible to that of the
original data.
WOOFER CONT
The sub woofer output can be adjusted.
31
32
30
34
35
36
37
36
Basic
operation
29
Page 31
Basic operation
Adjusting sound quality
Setting Circle Surround II
The Circle Surround II function enables surround sound and boosts bass even if the center
speaker and sub woofer are not connected. It can also be applied to dialog data when
listening to the radio.
Touch in an audio operation
LOW
(●)
screen or the VTR/DVD screen.
● Each touch of the switch switches the
status in the order shown below.
OFF LOW HI
● LOW : Low re-creation effect
HI : High re-creation effect
OFF : The function is disabled.
30
●You cannot set Circle Surround II at the same time as DSP, EQ or POS.
●Circle Surround II, SRS, and the (● ) symbol are trademarks of SRS Labs, Inc.
●Circle Surround II technology is manufactured under license from SRS Labs, Inc.
Page 32
Setting DSP (acoustics)
The DSP function reproduces the sensation of various factory set performance environments
by adding reverberation to the music being played.
DSP mode setting
Touching the DSP touch switch
brings up the acoustics mode
screen as shown.
The factory set DSP (acoustics) level for each mode can be adjusted to preference and saved.
BACK
The acoustics mode adjustments will
be saved and the system will return to
the previous operation screen.
Concert hallDisco/Club
LIVETHEATER
Live performance
arena
Church with echoDSP OFF
Adjusting, saving DSP (acoustics)
Movie theater/theater
Basic
operation
Touch or at the left of the
screen while in the preferred
acoustics mode.
● There are five + and five - adjustment
levels available.
Touch the switch for the acoustics
mode that has been adjusted until
you hear a beep.
●When adjusting the level for the currently selected DSP (acoustics) mode, the
level will not be saved for other acoustics modes.
●You cannot set DSP (acoustics) at the same time as Circle Surround II.
31
Page 33
Basic operation
Adjusting sound quality
Resetting DSP (acoustics) levels
Default settings for the currently adjusted and saved DSP (acoustics) level can be reset.
Touch until you hear a beep.
● The acoustics level will be returned to default value.
OFF
Adjusting EQ (equalizer)
Adjusts sound quality to preferred characteristics according to the music genre and audio
source.
Setting sound quality
Each factory set equalizer curve can be set to a preferred curve.
Touching the EQ touch switch
brings up the equalizer mode
screen as shown in the illustration.
● Touch after making settings.
BACK
The equalizer mode adjustments will
be saved and the system will return to
the previous operation screen.
Touch switchEqualizer mode types
FLAT
EQ1
EQ2
EQ3
EQ4
EQ5
No EQ correction
POPS effect curve
ROCK effect curve
JAZZ effect curve
CLASSIC effect curve
VOCAL effect curve
32
You cannot set EQ at the same time as Circle Surround II.
Page 34
Adjusting/Saving an EQ curve
Each factory set equalizer curve can be adjusted according to user preference and saved.
Touch the screen and slowly draw
the image of the preferred
equalizer curve with your finger.
To make fine adjustments, touch
the switch for the frequency to be
adjusted.
Touch or at the left of the
screen to perform fine adjustments.
Touch the switch you want to use
to save ( to ) until you
EQ1EQ5
hear a beep.
● The saved equalizer curve can be used
for other settings.
● Touch after making settings.
BACK
The equalizer mode adjustments will
be saved and the system will return to
the previous operation screen.
Resetting EQ curves
Currently saved equalizer curves and factory set equalizer curves can be returned to the
default values.
Basic
operation
Touch until you hear a
FLAT
beep.
● The equalizer curve will be reset to
default values.
33
Page 35
Basic operation
Adjusting sound quality
Adjusting POS (Positioning selector)
Sound localization can be adjusted according to the number and position of passengers in
order to obtain optimum acoustic effects.
A seat's sound localization can be adjusted simply by touching the switch.
Touch each seat image displayed
in the POSITION setting screen to
switch the sound localization for
that seat.
● The selected position will turn Lightblue. Touch the seat again to cancel
the selection. The four positions shown
by the table below can be set.
● Touch to cancel all settings.
● Touch after making settings.
OFF
BACK
The position will be saved and the
system will return to the previous
operation screen.
Touch switchFunctionTouch switchFunction
Acoustics optimized for
driver's seat
Acoustics optimized for
passenger's seat
●You cannot set POS (Positioning selector) at the same time as adjusting Circle
Surround II or the balance (next page).
●This product is configured for vehicles with left-hand drive.
34
Acoustics optimized for
both front seats
Acoustics optimized for
rear seats
Page 36
Setting the balance
The left/right/front/rear balance can be adjusted so that sound from all speakers arrives at the
listener's ears at the same time.
Touch in the POSITION
setting screen to display the
volume balance adjustment
screen.
Touch the screen at the preferred
balance point.
● To make fine adjustments, touch ,
● Touch to set the volume
● Touch after making settings.
● To set the position again, touch
FAD/BAL
, , or .
CENTER
balance to the center position.
BACK
The set volume balance will be saved
and the system will return to the
previous operation screen.
POS
and repeat the steps above.
Basic
operation
●You cannot set the balance at the same time as adjusting POS (Positioning
selector) (previous page).
●Touch and hold
values continuously. Adjustment will lock when it reaches the center value, and
, , or while making fine adjustments to adjust
, , or must be touched again to continue adjustment.
35
Page 37
Basic operation
Adjusting sound quality
Setting LOUDNESS
Audio can be modulated to correct for insufficient bass and treble when listening at low
volume.
green.
SETTING
ON
ENTER
OFF
Touch in the
INFORMATION screen.
Touch , or for
LOUDNESS.
● The selected touch switch will turn
To u ch .
Setting sub woofer
When a sub woofer is connected, the preferred output level for the audio can be set.
Touch in the
INFORMATION screen.
Touch or for WOOFER
CONT.
To u ch .
SETTING
ENTER
36
Page 38
Setting the harmonizer
It is possible to set the sound quality boost level to automatically regenerate harmonics such
as reverberation, depth, and tone lost in compression, producing a much clearer sound.
Touch in the
INFORMATION screen.
SETTING
Basic
operation
Touch or for
LOW
HI
HARMONIZER.
LOW
● : Low level of correction
HI
: High level of correction
OFF
: No correction
To u ch .
ENTER
You cannot set LOUDNESS at the same time as Circle Surround II.
37
Page 39
Basic operation
5. Setting background screen
The background for the audio operation screen, information screen and navigation screen can
be changed to a preferred wallpaper.
Setting the wallpaper
Press and the
INFO
INFORMATION screen will appear.
Touch .
To uc h
SETTING
1234
, , , or for
WALLPAPER.
● The selected touch switch will turn
green and the wallpaper (background)
will switch.
To u ch .
ENTER
38
Page 40
Basic operation
6. Adjusting/setting the screen
Switching the FUNCTION switch display
Touch switches not frequently used are not displayed in the audio operation screens and DVD
screens. These switches can be displayed as follows.
Touch .
● The FUNCTION switches appear.
● The FUNCTION switches are different
● The FUNCTION switches can be
● If the FUNCTION switches are
FUNC
in each audio mode.
hidden by touching again or
by touching an area of the screen
outside of the FUNCTION switch box.
displayed, operations corresponding to
other switches cannot be performed.
Hide the FUNCTION switches, then try
the operation again.
FUNC
Basic
operation
39
Page 41
Basic operation
Adjusting/setting the screen
Quality adjustments can be made for images such as the audio operation screen, navigation
screen and DVD or VTR (optional).
Displaying the image adjustment screen
Contrast, brightness and other picture settings can be adjusted to match preferences for
viewing DVD video or the audio operation screen.
To make viewing easier, the display switches between daytime display/nighttime display
according to whether the vehicle lights (parking lights, taillights, license plate lights) are on/off.
(Default settings)
● Vehicle lights are on . . <Nighttime display>
● Vehicle lights are off . . <Daytime display>
[Audio operation screen]
●Daytime display [Vehicle lights are off]● Nighttime display [Vehicle lights are on]
[DVD/VTR Screen]
●Daytime display [Vehicle lights are off]● Nighttime display [Vehicle lights are on]
40
Page 42
Press on the audio mode operation screen or DVD/VTR screen.
DISP
Touch after making any adjustments.
● If no operations are made after about 20 seconds, the display will return to the
The daytime display and nighttime display can be separately adjusted.
●When adjusting audio operation screen or
navigation screen
CONTRAST
●When adjusting DVD/VTR screen
Touch to increase contrast, or to decrease contrast.
BRIGHT
Touch to increase brightness, or to decrease brightness.
COLOR (for DVD/VTR screen only)
Touch to increase green, or to increase red.
TINT (for DVD/VTR screen only)
Touch for a darker tint, or for a lighter tint.
Switching screen mode
Touch .
● DVD : Touch followed by in
WIDE
SET
the operation screen.
VTR : Touch in the operation
SET
screen.
42
To uc h , ,
● This selects the wide mode.
NORMALWIDE1
WIDE2WIDE3
or .
Page 44
To u ch .
BACK
● Returns to the DVD or VTR operation screen.
Basic
operation
NORMAL mode
The screen is shown with a vertical to
horizontal ratio of 3 to 4. The side edges
are black.
WIDE 2 mode
Only the left and right edges of the screen
are stretched out. However, the vertical to
horizontal ratio of 3 to 4 is maintained at
the center of the screen to provide a
comfortable wide screen image.
WIDE 1 mode
The screen is shown with a vertical to
horizontal ratio of 3 to 4 and is expanded
in the left and right directions. A wide
screen effect can be displayed without
any image loss.
WIDE 3 mode
The screen is expanded in both the
vertical and horizontal directions by the
same ratio. The image is clipped slightly
at the top and bottom edges.
Viewing of wide screen modes is permitted when limited to the personal
entertainment of the user, but exercise caution as using technologies such as
image compression and expansion for the purpose of commercial benefit or public
presentation may infringe upon the rights of the copyright holder protected by
applicable copyright law.
43
Page 45
How to operate the tuner
1. How to use the AM/FM radio
SOURCE MENU RECALL switch
PWR
button
SOURCE MENU
button
Preset switches
TUNE TRACK
button
FUNCTION switch
AUTO.P
Listening to the AM/FM radio
Press or touch the SOURCE MENU RECALL switch.
Touch for AM radio, or for FM radio.
SOURCE MENU
AMFM
44
Page 46
Selecting radio stations
Manual selection
Press or .
● Pressing the switch once moves the frequency one step up or down. (One step on the
AM band is 10kHz. One step on the FM band is 0.2MHz)
● (up) : Raises the frequency
(down) : Lowers the frequency
Automatic selection
Press and hold or until you hear a beep.
● The station that is closest to the current frequency will be searched for automatically,
and searching will stop when the station is received. To stop the search before a
station is found, press the button again.
Selection using preset switches
Touch a preset switch that already has a station recorded.
● See "Saving radio stations" on next page for more information.
RADIO
If the reception for a particular station is weak in the area you are in, the automatic
selection may not work.
45
Page 47
How to operate the tuner
How to use the AM/FM radio
Saving radio stations
There are two modes for saving radio stations, manual and AUTO. P. These modes operate
independently.
Saving manually
Make sure "AUTO. P" is not displayed in the upper part of the screen.
●
If displayed, display the FUNCTION switch and touch to switch to manual.
Use manual tuning or automatic tuning to select the station to be saved.
Choose a preset switch and touch it until you hear a beep.
● The radio station (frequency) is set. Touch the preset switch to tune in the selected
station.
Saving with AUTO.P
AUTO.P
46
To u ch .
Touch until you hear a beep.
● The AUTO.P function will activate and start automatically selecting stations. You will
FUNC
AUTO.P
hear a beep when the automatic selection of stations is completed. Touch
again to switch the display back to the broadcast station originally saved.
AUTO.P
Changing stations saved by AUTO.P
Use manual tuning or automatic tuning to select the station to be saved.
Touch the preferred preset switch until you hear a beep.
Page 48
About AUTO.P
Because the AUTO. P function can be used to temporarily save stations for the
preset switches, stations saved manually will remain in memory even if AUTO. P is
used. Manually saving stations that are used regularly allows them to be restored
even after AUTO. P has been used, such as after traveling.
Touching while AUTO.P is operating or after it has been used will return
AUTO.P
the preset memories to their previous settings. (The stations saved with AUTO. P will
be deleted.) The diagram below shows how to switch from AUTO. P to manual.
RADIO
Automatically saving
stations to preset switches
Manual
Touch until
AUTO.P
you hear a beep.
To uc h
AUTO.P
(The stations saved with
AUTO.P will be deleted)
AUTO.P
(Search started)
AUTO.P
(Search
completed)
●AUTO. P may not automatically receive stations if radio waves in the surrounding
area are weak.
●A frequency saved with the tuning switch may not match the frequency saved
with AUTO. P even though the signal is received from the same station.
●Due to conditions for receiving radio waves, saved stations may differ even when
the AUTO. P switch is operated repeatedly in the same location.
●Up to six stations with good signal reception are automatically saved in order of
frequency (low to high).
●When less than six stations capable of reception are found, nothing is saved for
the remaining preset switches.
47
Page 49
How to operate the tuner
How to use the AM/FM radio
Turning off the radio
Press .
● Press again to turn on the
PWR
PWR
radio and resume reception of the radio
station (frequency) received before
power was turned off.
Playback starts when a CD is inserted into the disc slot.
● The default setting for MUSIC JUKE in digital recording mode is AUTO. When a CD is
inserted into the disc slot, MUSIC JUKE automatically starts recording at the same time as
playback begins. Press for at least one second to stop recording.
● "REC" is displayed while recording is in progress. While waiting for recording to start
"REC" changes to "". See "Recording with MUSIC JUKE" (page 80).
Press or touch the SOURCE MENU RECALL switch
SOURCE MENU
when a CD has been inserted.
Touch .
● Playback will begin.
CD
REC
CD
●Titles and track names can be displayed when they are recorded on a CD. Up to
28 characters can be shown in the display.
●Only characters recorded by ASCII code can be shown on the CD-TEXT display.
●The CD-TEXT display may not be able to show characters for discs recorded
with many title characters.
●There may be occasions when CD-R/RW CD-TEXT cannot be displayed.
●Even if the title track is not contained on the music CD itself, the title will still be
displayed if the corresponding information is stored in MUSIC JUKE database. If
there is multiple data corresponding to a single track, the title is not displayed.
49
Page 51
How to operate the CD player
How to use the CD player
Selecting a track
You can jump to the opening of a track you want to hear.
It is possible to fast-forward/rewind the track being played.
Press and hold or until you hear a beep.
● (up) : Fast-forward
(down) : Rewind
If you hear a beep while rewinding (fast-forwarding), the deck has switched to fastforward (rewind) mode and will continue you remove until your finger from the button.
Searching for a track
To u ch .
To u ch .
● The deck will play the first 10 seconds of each track. Touch again to continue
FUNC
SCAN
playing the current track.
Repeating a track
To u ch .
Touch .
● Repeats the current track.
● The track will repeat until the function is canceled. Touch again to cancel.
50
FUNC
RPT
SCAN
RPT
Page 52
Playing tracks in random order
To u ch .
To u ch .
● Plays tracks in random order.
● Random playback will continue until the function is canceled. Touch again to
● At the end of each track the system arbitrarily chooses which track to play next. As a
FUNC
RAND
RAND
cancel.
result, it is possible for the same track to be played multiple times in a row.
Turning off the CD player
PWR
Press .
● Press again to resume playback.
● MUSIC JUKE will continue to record even if the CD is turned OFF while recording is in
progress. Press for at least one second to stop recording.
REC
CD
51
Page 53
How to operate the MP3 player
1. How to use the MP3 player
For safety considerations, some functions are disabled while the vehicle is in motion.
SOURCE MENU RECALL switch
PWR
button
SOURCE MENU
button
Example of MP3 file structure
Explanations are based on this example of MP3 file structure.
Playback starts automatically when a CD is inserted into the disc slot.
Press or touch the SOURCE MENU RECALL switch
SOURCE MENU
when a disc has been inserted.
To u ch .
● Playback will begin.
● The CD player screen will be shown for about 2 seconds as the system checks
● Normally, tracks are played back in the order .
● When multiple MP3 files and folders are on the same level, they are played in
MP3
whether the inserted CD is a music CD or an MP3.
ascending order by folder and file names.
Selecting a music file
A music file located within a folder can be selected.
Selecting with file change switches
Touch the music file.
● The currently selected file name and folder name will be shown in the display.
● When 9 or more music files are located in the same folder, touch or to show
data not currently displayed. (This function is not available when the vehicle is in
motion)
Selecting with TUNE/TRACK button
When several music files are located in the same folder, the next music file or previous music
file can be selected with the track selection (track start point).
MP3
Press or .
● (up): Selects next music file
(down): Selects previous music file
●If music data and MP3 data have been recorded on the same disc, playback is
not possible.
●When an MP3 is being played, navigation operation will become slower. This is
not a malfunction of the system.
53
Page 55
How to operate the MP3 player
How to use the MP3 player
Fast-forwarding/rewinding
It is possible to fast-forward/rewind within the current file.
Press and hold or until you hear a beep.
● (up): Fast-forward
(down): Rewind
If you hear a beep while rewinding (fast-forwarding), the deck has switched to the fastforward (rewind) mode and will continue until you remove your finger from the button.
Changing display of the current level
The folder level can be switched and displayed.
Touch or .
●: Displays the next folder level up.
HOME
●: Displays the level of the file currently being played.
HOME
Displaying the current level
Displays the file currently being played.
To u ch .
HOME
Searching for a music file
To u ch .
To u ch .
● The system will play the first 10 seconds of each file located within the same layer of
FUNC
SCAN
the folder currently being played. Touch again to continue playing the current
file.
SCAN
54
Page 56
Repeating the same music file
To u ch .
Touch .
● Repeats the current file.
● The file will repeat until the function is canceled. Touch again to cancel.
FUNC
RPT
RPT
Playing music files in random order
To u ch .
To u ch .
● Files will be randomly selected from among all files at the same level as the folder
● Plays files in random order.
● Random playback will continue until canceled. Touch again to cancel.
● Touch during random playback to repeat the file currently being playing. Touch
● At the end of each file the system arbitrarily chooses which file to play next. As a
FUNC
RAND
currently being played.
RAND
RPT
RPT
again to return to random playback.
result, it is possible for the same file to be played multiple times in a row.
MP3
See page 52 for an example MP3 file structure.
If of the third level is being played and the display shows the folder and files of
the second level ( , and ), touch to display the folder and file of
the third level ( and
).
HOME
55
Page 57
How to operate the MP3 player
How to use the MP3 player
About display of file information
Folder names and file information (album name and track titles) recorded on the disc can be
displayed. The number of characters that can be displayed is shown below.
Screen Display
Folder/file namesMusic file information
8 characters max.28 characters max.
Displaying folder/file names
Press to display the
CONT
operation screen.
Displaying file information
To u ch .
● The switch will change to
TITLE
TITLE
TITLE OFF
information is being displayed. Touch
TITLE OFF
to a folder/file switch.
when the file
to change the display
Turning off the MP3 player
PWR
Press .
● Press again to resume playback.
PWR
56
Page 58
About MP3s
MP3 (MPEG-1 Audio Layer III) is a standard format for audio compression technology. By
using MP3, a file can be compressed to one-tenth its original size.
This unit has limitations on MP3 file standards and the recorded media and formats that can
be used. Be aware of the following points when recording MP3 files.
MP3 files have an "ID3 Tag" that allows input of information so that data such as track title and
artist can be saved.
This unit supports ID3v. 1. 0 and ID3v. 1. 1 tags. Use only ASCII code to record tags, since
only ASCII code is supported by this deck. Recording of characters not included in ASCII code
will result in display of garbled characters.
MP3
Media
Media capable of playing MP3 include CD-ROM, CD-R and CD-RW discs.
Compared to CD-ROM media commonly used for music discs, CD-R discs are fragile in high
temperature/high humidity environments and sections of the CD-R may become incapable of
playback. Fingerprints or scratches on the disc may prevent playback or cause skipping.
Sections of a CD-R may deteriorate if left inside a vehicle for long periods of time.
It is also recommended that CD-R discs be kept in a light-blocking case because the discs are
vulnerable to ultra-violet light.
Use 128kbps or lower for the MP3 bit rate. If the bit rate exceeds 128kbps, there
may be sound jumping during MP3 playback.
57
Page 59
How to operate the MP3 player
How to use the MP3 player
Format of discs
The format of discs to be used must be ISO9660 Level 1 or Level 2. Also, be sure to record in
"MODE 1". Discs recorded in "MODE 2" are not supported.
MP3 files recorded in formats other than those outlined above may result in files that cannot
be played normally and file names and folder names that do not display properly.
The following additional limitations apply:
● Maximum directory layers : 8 levels
● Maximum characters for folder names/file names: 31 (including "." and the 3 letters of the
file extension)
● Allowable characters for folder names/file names : A-Z, 0-9, _ (underscore), all ASCII
characters
● Number of files/folders possible in a single folder : 512*
* Each file is counted as one file, even if it is not an MP3 file (i. e. files with extensions other
than ".MP3").
[Configuration example for CD supporting MP3]
F1
Folder1
001.MP3
002.MP3
003.MP3
004.TXT
005.MP3
300.MP3
F301
F302
F512
● Total number of files/folders that can be recorded on a single disc: 1023
Folder301
Folder302
Folder512
A total of 512 files and folders can be
created within a single folder.
Each file is counted as one file, even if it
is not an MP3 file (e.g. 004.TXT).
58
Page 60
File names
Only files with the MP3 file extension ".mp3" will be recognized as MP3 and played in the unit.
Be sure to save MP3 files with the ".mp3" file extension.
Use capital letters for "MP".
Multi-sessions
Multi sessions are supported and CD-R/RW with recorded MP3 files can be played. When
recording using "Track at once", however, finalize the disc with session close or write protect.
Playing MP3
When a disc containing an MP3 file is inserted, all files on the disc will be checked before
playback can begin. The check will be completed within approximately 10 seconds of the disc
being inserted, and the first MP3 file will begin playing. If the check is not completed within this
period, the music or audio previously being played will resume. MP3 playback can be started
by touching .
Sound is not emitted from the system while it is checking the files on the disc.
In order to speed up completion of the file check, it is recommended that you avoid recording
files that are not MP3 files and avoid creating unnecessary folders.
In addition, it is recommended that you record all data in a single session because a multi
session disc takes time for CD control information acquisition.
While an MP3 is being played, navigation operation will become slower. This is not a
malfunction of the system.
MP3
MP3
MP3 playing time display
It is possible that playing time will not be correct, depending on the writing condition of the
MP3 file.
* It is possible that playing time will not be correct when VBR Fast Up/Down is operated.
Display order of MP3 file/folder names
Names of MP3 folders and files within the same level are displayed in the following order.
1. MP3 files displayed first, by ascending order of numbers, letters.
2. Folders displayed next, by ascending order of numbers, letters.
If the ".mp3" file extension is attached to a file other than an MP3 file, that file will
be mistakenly recognized by the unit as an MP3 file and played, resulting in noise
and static that can damage the speakers. Do not attach the ".mp3" extension to
any non-MP3 files.
59
Page 61
How to operate the MP3 player
How to use the MP3 player
Making and playing MP3 files
MP3 files created by recording broadcasts, records, audio recordings, video recordings or live
performances cannot be used for purposes other than personal entertainment without
permission of the copyright holder as set forth in copyright law.
Downloading from Internet MP3 music sites
There are many kinds of sites that distribute MP3 files on the Internet, such as "pay per
download" online shopping sites, "try before you buy" listening sites and free download sites.
Follow the rules for each site (such as paying fees) and download according to site
instructions.
Converting CD music to MP3 files
Prepare a computer with commercially available MP3 encoding software (conversion
software). (Some encoding programs available on the Internet do not require payment.) Music
data files in MP3 format can be made by inserting the music CD into the CD-ROM drive of the
computer and following the procedures of the MP3 encoding software to compress the songs
of the music CD. A 12cm music CD (having a maximum of 74 minutes of recording/650MB of
data) can be compressed to 65MB (about 1/10 of the original size).
When writing to CD-R/RW
MP3 files can be recorded on CD-R/RW by using a CD-R/RW drive connected to a computer.
Record by setting the recording format of the recording software to ISO9660 level 1 or level 2
(not including extension format).
Select CD-ROM (mode 1) for the disc format. Discs recorded with CD-ROM xA (mode 2)
cannot be played on this deck.
When playing back CD-R/RW
Insert a CD-R/RW containing recorded MP3 files. The system will automatically determine
whether the disc is a music CD or a CD-R/RW with MP3 files and begin playing the disc. A
music CD recorded onto a CD-R/RW can also be played. However, depending on the type of
disc being used, playback may not be possible.
●A fixed bit rate of 128kbps and sampling frequency of 44.1kHz is recommended
for obtaining stable audio quality at playback.
●Depending on the characteristics of a disc, the system may not be able to read
CD-R and CD-RW discs.
●Because there are many types of MP3 encoding software available, including
commercial and freeware programs, audio quality may deteriorate, noise may be
generated when playing starts and some recordings may not play, depending on
the condition of the encoder and the file format.
●When files other than MP3 files are recorded on a disc, the system may take
some time to recognize the disc or it may not play.
60
Page 62
How to operate the Memory Stick player
1. How to use the Memory Stick player
The unit can play music data recorded on the Memory Stick using ATRAC3 (audio
compression technology).
SOURCE MENU
RECALL switch
PWR
button
SOURCE
MENU
button
Listening to Memory Stick data
Insert a Memory Stick into the slot and touch .
Press or touch the SOURCE MENU RECALL switch
SOURCE MENU
when a Memory Stick has been inserted.
Touch .
● Playback will begin.
MEMORY STICK
●This unit can only play music data recorded on MG Memory Sticks (white).
●This unit cannot play music data recorded using ATRAC3 Plus.
●The unit cannot be operated for about 4 seconds after an MG Memory Stick has
been inserted as while system is checking the data.
●If recorded in the Memory Stick, the artist name, song title (track name), and
other details can be displayed on the screen. Up to 28 characters can be shown
in the display.
●If the number of plays and/or playback period is restricted, the relevant number/
period is displayed in the screen.
●A message is displayed if the number of remaining plays reaches 0 or if the
playback period has expired. (See page 142)
It is possible to fast-forward/rewind within the current track.
Press and hold or until you hear a beep.
● (up) : Fast-forward
(down) : Rewind
If you hear a beep while rewinding (fast-forwarding), the deck switched to fast-forward
(rewind) mode and will continue until you remove your finger from the button.
Searching for a track
To u ch .
Touch .
● The deck will play the first 10 seconds of each track. Touch again to continue
FUNC
SCAN
playing the current track.
Repeating a track
To u ch .
To u ch .
● Repeats the current track.
● The track will repeat until the function is canceled. Touch again to cancel.
62
FUNC
RPT
SCAN
RPT
Page 64
Playing tracks in random order
To u ch .
Touch .
● Plays tracks in random order.
● Random playback will continue until the function is canceled. Touch again to
● At the end of each track the system arbitrarily chooses which track to play next. As a
FUNC
RAND
RAND
cancel.
result, it is possible for the same track to be played multiple times in a row.
When only one CD changer is connected, touch . When
two CD changers are connected, touch or
CD CHANGER2
.
Selecting a track
See "How to use the CD player" (Page 50).
Fast-forwarding/rewinding
See "How to use the CD player" (Page 50).
Selecting a CD
A CD can be selected from among all the discs in the changer.
Touch one of the disc change switches.
● The number for the selected CD will change color.
64
CD CHANGER1
CD CHANGER1
Page 66
Searching for a track or CD from all CDs in the
changer
Searching for a track
See "How to use the CD player" (Page 50).
Searching for a CD
To u ch .
Touch .
● The system will play the first 10 seconds of the first track of each CD in the changer.
FUNC
DISC SCAN
Touch again to continue playing the current track.
DISC SCAN
Repeating a track or CD
Repeating the current track
See "How to use the CD player" (Page 50).
Repeating the current CD
To u ch .
Touch .
● Touch once to continue repeating the CD. Repeat will continue until canceled. Touch
FUNC
DISC RPT
DISC RPT
again to cancel.
CD Changer
●A disc change switch is displayed for each disc tray in the changer but only the
disc change switches that correspond to a currently loaded tray can be selected.
●No operation is possible when there are no discs loaded into the CD changer.
●If there are 2 CD changers connected, use and
CD CHANGER2
main CD changer.
to switch between the optional CD changer deck and the
CD CHANGER1
65
Page 67
How to operate the CD Changer
How to use the CD changer
Playing tracks in random order
Playing tracks on current CD in random order
See "How to use the CD player" (Page 51).
Playing tracks on all CDs in random order
To u ch .
Touch .
● Setting once will start random playback which will not stop until the function is
● At the end of each track the system arbitrarily chooses which track to play next. As a
FUNC
DISC RAND
canceled. Touch again to cancel.
result, it is possible for the same track to be played multiple times in a row.
DISC RAND
Turning off the CD changer
PWR
Press .
● Press again to resume playback.
PWR
66
Page 68
How to operate MUSIC JUKE
1. Before using MUSIC JUKE
Description of MUSIC JUKE
MUSIC JUKE can record music or audio from a CD, radio etc. Using ATRAC3 audio
compression technology. There are two types of recording available, digital and analog. When
you digitally record an album from the CD player, "Gracenote CDDB
Service" will search for the album name, artist name and genre and automatically create a list
(playlist) displaying the relevant data. Recording from any other source is done in analog and
a playlist is created for the recorded source/date recorded.
*...When the relevant name cannot be found, a playlist will be created in the same way as
analog recording.
About the structure of MUSIC JUKE
In MUSIC JUKE, music/audio is recorded into 6 different play modes and then stored into
playlists created in each play mode for managing your data. Being able to narrow down from
play modes and playlists before searching for the music you want to listen to makes the listening
experience even more comfortable and rewarding.
£
Music Recognition
PLAY MODE
Recorded music
(tracks) are divided into
6 play modes (ALBUM,
ARTIST, GENRE, etc.)
Search method
By favorites
By date recorded
From all recorded tracks
By genre
By artist name
By album name
PLAYLIST
Recorded music
(tracks) stored in each
of the play modes is
sorted into playlists.
Select play mode
MY SELECTION
DATE
TRACK
GENRE
ARTIST
ALBUM
TRACK
Title of recorded music/audio data
Select playlist
Favorites
Date
Corresponding tracks
♪♪
♪
♪♪♪
POPS
Artist name
Album name
♪♪
♪♪♪
♪
67
JUKE
MUSIC
Page 69
How to operate MUSIC JUKE
Before using MUSIC JUKE
About Play Modes/Playlists
The system sorts recorded music into groups depending on type and recording conditions and
saves it to MUSIC JUKE.
Recorded music can be sorted into automatically created playlists within the 6 play modes,
based on album name, artist name, or genre. It is also possible to create a personal group
containing a collection of preferred songs.
PLAY MODEPLAYLIST
● When recording has finished, a playlist containing the recorded tracks
is created. If the album name has been retrieved using Auto-titling, it
ALBUM
MY SELECTION
TRACK
ARTIST
GENRE
DATE
will be set as the playlist name. If the album name has not been
retrieved using Auto-titling, the source/ALBUM/number will be set as
the playlist name.
● It is possible to select a song by album name.
● This is an original playlist containing a collection of your preferred
songs. A new list can be created by editing the information of the
recorded tracks.
● It is possible to select a song by an original playlist name.
● There are no playlists.
● It is possible to select a track by song name.
● When the artist name for the recorded song has been retrieved using
Auto-titling, a playlist is created for that artist.
● It is possible to create a playlist by entering the artist name in the
information for the recorded track.
● It is possible to select a song by artist name. When more than one
album by the same artist has been recorded, a list of albums is
displayed from which to make a selection.
● When the genre for the recorded song has been retrieved using Auto-
titling, a playlist will be created for this genre.
● It is possible to select a song by genre. When more than one album in
the same genre has been recorded, a list of albums is displayed from
which to make a selection.
● A playlist is created for a recording date.
68
Up to 999* playlists can be created in MUSIC JUKE with a maximum of 99 tracks
recorded in each playlist. The total number of recordable tracks is 3000*.
* The number of playlists that can be created and tracks that can be recorded
differs according to recording time and recording mode.
Page 70
About databases
When recording a CD album (album/single disc) digitally from the built-in CD player to MUSIC
JUKE, the system searches the hard disc database and automatically retrieves any available
information such as album name, artist name, genre, and title for the recorded album.
The information recorded in the unit uses data from the Gracenote CDDB database.
About Gracenote CDDB
Gracenote is CDDB, Inc. d/b/a "Gracenote."
CD and music-related data from Gracenote CDDB
Music Recognition Service2000, 2001, 2002 Gracenote. Gracenote CDDB Client Software
2000, 2001, 2002 Gracenote.
U.S. Patent No. 5,987,525, 6,061,680, 6,154,773 and others granted or under application.
CDDB is a registered trademark of Gracenote. The logos and logotypes of Gracenote,
Gracenote CDDB, and "Powered by Gracenote CDDB" are trademarks of Gracenote. Music
Recognition Service and MRS are service marks of Gracenote.
Music recognition technology and related data provided by Gracenote and the Gracenote
CDDB
Music Service. Gracenote is the industry standard for music recognition technology and
relevant content delivery.
For more details, see www.gracenote.com.
£
JUKE
MUSIC
●The information recorded in the unit uses data from the Gracenote CDDB 207
database (updated November, 2004).
●The content of data provided courtesy of "Gracenote CDDB
Service" cannot be 100% guaranteed.
£
Music Recognition
69
Page 71
How to operate MUSIC JUKE
♪♪♪♪
♪♪
♪♪♪
Before using MUSIC JUKE
About Auto-titling
The system automatically sorts and groups recorded music into playlists based on recording
conditions and title information retrieved from the database.
* The data retrieved using Auto-titling may differ from the actual title information.
Digital recording
Digital recording
Hard disc
Music data
When corresponding
album title, artist,
and/or genre
information
can be found
PLAY MODE
ALBUM
MY SELECTION
TRACK
ARTIST
GENRE
DATE
PLAY LISTTRACK
Album title
Artist
Genre
Record date
Album title
Album title
A playlist is automatically created for the ALBUM,
ARTIST, GENRE, and DATE play modes.
Unit
database
When corresponding album title, artist,
and genre information cannot be found
PLAY MODEPLAY LISTTRACK
♪
♪♪♪♪
♪♪
♪♪♪
・・・・・
・・・・・
ALBUM
MY SELECTION
TRACK
ARTIST
GENRE
DATE
A playlist is automatically created for
the ALBUM and DATE play modes.
CD/ALBUM/0001
Record date
2005.3.24/CD/0001
2005.3.24/CD/0002
2005.3.24/CD/0003
2005.3.24/CD/0004
・・・・・・・・
・・・・・・・・
70
Page 72
♪
♪♪♪♪
♪♪
♪♪♪
Analog recording
Hard disc
Music data
PLAY MODEPLAY LISTTRACK
ALBUM
MY SELECTION
TRACK
ARTIST
GENRE
DATE
CD/ALBUM/0001
Record date
A playlist is automatically created for
the ALBUM and DATE play modes.
Analog recording
2005.3.24/CD/0001
2005.3.24/CD/0002
2005.3.24/CD/0003
2005.3.24/CD/0004
・・・・・・・・
・・・・・・・・
JUKE
MUSIC
In analog recording, or when title information can not be found for digital recording,
the following information is assigned and a playlist is created in the play modes
shown below.
ALBUM play mode...Source/ALBUM/4-digit number*
TRACK play mode...Date/Source/4-digit number*
* When the date has changed, a number is assigned in ascending order from 1.
71
Page 73
How to operate MUSIC JUKE
Before using MUSIC JUKE
About displaying database information
It is possible to see the version information stored in the hard disc’s title database.
Press .
Touch .
Touch for CDDB
VERSION.
● Information regarding the Gracenote
INFO
DATA
INFORMATION
CDDB database will appear.
72
Page 74
About updating the database
The database in the unit (Gracenote CDDB database) can be updated using provided data.
We will provide information regarding updates at a later date.
Press .
Touch .
INFO
DATA
Insert a Memory Stick or CD-R/RW
containing update information.
Touch or
● The database update begins.
MS UPDATE
DISC UPDATE
.
JUKE
MUSIC
Once title information for a file has been retrieved it will not be automatically
changed even if the updated Gracenote CDDB database contains relevant data.
This information can be updated when editing. For details, see "Retrieving title
information from the database" on page 95.
73
Page 75
How to operate MUSIC JUKE
Before using MUSIC JUKE
Checking hard disc capacity
It is possible to display the number of recorded tracks and playlists on the hard disc. You can
also check the number of tracks that can still be recorded and number of playlists that can still
be created.
Press .
Touch .
Touch for HARD
DISC DRIVE.
● Hard disc capacity is displayed.
INFO
DATA
INFORMATION
74
Page 76
How to operate MUSIC JUKE
This flow chart explains operations such as recording with MUSIC JUKE, playlist and track
editing, and listening to MUSIC JUKE.
Recording with MUSIC JUKE (Page 80)
To change recording method
To listen to MUSIC JUKE
To create/edit
a playlist
●
Creating a playlist
(Page 90)
●
Changing the artist
(Page 105)
●
Editing a playlist name
(Page 93)
●
Retrieving title information
from the database (Page 95)
● Setting digital recording mode
(Page 79)
● Setting Auto Marker
(Page 79)
● Setting recording bit rate
(Page 80)
Editing track information
(Page 103)
To add a track to
a playlist
Adding a track (Page 101)
To edit track
information
JUKE
MUSIC
MUSIC JUKE Playback
75
Page 77
How to operate MUSIC JUKE
2. Recording with MUSIC JUKE
About recording with MUSIC JUKE
● MUSIC JUKE can record music from the built-in CD player or optional CD changer as well
as music and audio output from the radio or VTR (audio).
● MUSIC JUKE cannot record from MP3 files, the Memory Stick, or DVDs.
About sources and recording styles that allow recording
The recording method used by MUSIC JUKE changes depending the source type.
Recording styleRecordable sources
Digital recording
Analog recording
● We cannot be held responsible for content that can not be recorded or music/audio data lost
as a result of malfunction, improper use, or defects.
● Recorded files may not be used for purposes other than personal entertainment without
permission of the copyright holder as set forth in copyright law.
● When recording content that will only be played once, try recording something in advance to
check that the system is functioning properly.
● If recording is in progress when the ignition is set to ACC ON and the engine is started,
recorded data may be lost.
● When recording from a gap less CD (no gaps between songs) pauses will be recorded
between songs and this may create unnatural gaps. Please be aware that this a result of the
type of disc being used.
● The music/audio will become inaudible for approximately 2 seconds at the start and finish of
recording.
● The music/audio will become inaudible for approximately 2 seconds at the start and
finish of analog recording.
● If switching to another mode (for example radio) while digital recording from a music
CD is in progress, recording is stopped and there is a 2 second pause before the radio
broadcast becomes audible.
● MUSIC JUKE will play tracks in order starting from the most recently recorded. When
recording a music CD, the order in which the songs are played may be the opposite to that
in which they are recorded on the CD depending on the selected play mode. See "To select a track (song)" on page 83 for information regarding playback order. It is also possible to
change the playback order. See "Switching playlist order" on page 97 for information on
changing the playback order.
● When CD recording starts, the recorded sound is output. When CD recording finishes, as
long as you do not turn off the engine (ACC OFF) or switch sources, the recorded sound will
continue to be output.
CD player
FM, AM, VTR (audio), CD changer, CD player (only CDs with
digital recording restriction)
Notes regarding recording
76
Page 78
● If the battery terminal has been disconnected then reconnected, the map screen will appear
and recording is not possible for approximately 2 minutes.
● If recording cannot be completed due to jumping or some other problem, is displayed on
the screen.
About digital recording
● This system is SCMS (Serial Copy Management System)-compliant. As a result, the
following CDs cannot, in principle, be digitally recorded.
● CD-R or CD-RW digitally recorded from a music CD*
● Protected CDs*
* Can be recorded in analog by pressing REC.
● The track (song) currently being recorded is deleted in the following cases.
● The engine is turned off (ACC OFF)
● The CD is ejected
● Recording automatically resumes in the following cases.
● The engine is switched on*1
● The CD is inserted*2
*1 Record: Recording is resumed from the unrecorded track (song) with the lowest track number
Play: Playback starts from the beginning of the interrupted track (song)
Recording only resumes when the engine is turned back on if recording had been in progress when it was
turned off
*2 Record: Recording is resumed from the unrecorded track (song) with the lowest track number
Play: Playback starts from the beginning of the inserted CD
● Recording continues in the following cases.
● Source is switched during recording
● Audio is turned off during recording
● An already recorded song cannot be recorded again.
● When recording has been stopped manually, only those songs that have been completely
recorded can be played back. To play songs not completely recorded, switch the source
then switch back to CD mode.
JUKE
MUSIC
About analog recording
● Analog cannot be used for continuous recording exceeding 5 hours. To continue, press
REC
again to record.
● If the engine is turned off (ACC OFF) during analog recording, recording is stopped. Analog
recording will also stop if the source is switched while still in progress.
77
Page 79
How to operate MUSIC JUKE
Recording with MUSIC JUKE
Setting recording method
It is possible to switch the recording method used in MUSIC JUKE.
To u ch .
Touch .
● MUSIC JUKE operation screen
● The following settings can be switched
DIGITAL RECSets digital recording to AUTO/MANUAL
AUTO TRACKSets track markers for recorded tracks (songs)
PLAYLIST DISPLAYReorders display/playback order for playlists/tracks
BITRATESets sound quality for recording
FUNC
SET
appears.
●MUSIC JUKE operation screen
in MUSIC JUKE setting screen.
●MUSIC JUKE setting screen
ItemFunctionPage
Next page
Next page
Page 97
Page 80
78
Page 80
Setting digital recording mode
AUTOMANUAL
When is set, digital recording begins as soon as a CD is inserted. When
is set, recording starts from the beginning of the track currently playing once the panel button
REC
( ) has been pressed. It is possible to switch between these two settings.
To u ch .
Touch .
Touch or .
● . . . . . Recording
● . . Press to
FUNC
SET
AUTOMANUAL
AUTO
automatically starts
when a CD is inserted.
MANUALREC
start recording.
Setting Auto Marker
Set track markers between tracks (songs) when recording a CD in analog.
To u ch .
Touch .
Touch or .
● . . . . . . . Tracks are set on a CD
● . . . . . . Set the entire section
FUNC
SET
ONOFF
ON
based on the gaps
between songs. For
sources other than
CDs, tracks are set
once all recording is
complete.
OFF
between the start of
recording to completion
as one track.
JUKE
MUSIC
It is possible that some tracks cannot be delimited using track markers even if Auto
Marker is set to ON.
79
Page 81
How to operate MUSIC JUKE
Recording with MUSIC JUKE
Setting the recording bit rate
The sound quality for recording can be selected. A higher bit rate means a higher sound
quality but also a larger file size.
To u ch .
Touch .
Touch , or .
● Digital recording is fixed at a bit rate of
FUNC
SET
132k105k66k
132k.
Recording with MUSIC JUKE
MUSIC JUKE allows digital recording from the CD player and analog recording from all other
sources.
Digital recording can be either AUTO or MANUAL. When AUTO is set, recording automatically
starts when playback begins. When MANUAL is set, recording starts when is
pressed.
“REC” is displayed while recording is in progress.
The following switches cannot be used while recording is in progress.
Recording
method
Digital
recording
Source
(Audio)
CD
Other sources*
Touch switchPanel buttons
RPT RAND SCAN
UnrestrictedUnrestricted
REC
Press and hold only
Press and hold only
RPT RAND SCAN
Analog
recording
* When the source has been switched to radio or CD changer during digital recording.
AM, FM, CD,
CD changer,
VTR
DISC
RPT
Preset switches
AUTO.P
DISC
RAND
∧ ∨
DISC
SCAN
80
Page 82
Automatically recording a CD during playback
As soon as a CD is inserted, recording automatically starts when playback begins.
Insert a CD.
● Recording and playback are
automatically started.
● Press for at least one
second to stop recording.
REC
REC mark
JUKE
MUSIC
●When a CD is re-inserted after having been ejected during recording, the system
plays the tracks that have been completely recorded while waiting for recording
to start. "" is displayed while waiting for recording to start.
●Recording from copy-restricted CD-R/RWs and sources other than the CD player
to MUSIC JUKE can only be done manually and in analog.
●If a CD is already inserted, recording will not automatically start even if the
source is switched to CD. Press to start recording. (See next page for
"Recording preferred tracks (songs) from a CD")
●Set Record Mode in "Setting digital recording mode" to
recording from a preferred song (see page 79).
REC
MANUAL
start
81
Page 83
How to operate MUSIC JUKE
Recording with MUSIC JUKE
Recording preferred tracks (songs) from a CD
Records preferred tracks (songs).
Play the CD.
Press for at least one
REC
second.
● Returns to the start of the track and
starts recording to MUSIC JUKE.
● Press for at least one
second to stop recording.
REC
Recording from sources other than a CD
Start recording whenever you like while playing the radio, VTR, or CD changer.
Switch to the source for recording.
● See "Switching modes" (Page 24).
Press for at least one
second.
● Start recording to MUSIC JUKE.
● Press for at least one second
to stop recording.
REC
REC
REC mark
82
●Already recorded tracks (songs) cannot be selected.
●To start recording at the same time as playback begins on a CD, set Record
mode in "Setting digital recording mode" (see page 79) to .
● If the power was turned off during playback, MUSIC JUKE will resume playback from
the beginning of the last track that was played.
To select a track (song)
Several tracks (songs) can be selected from all those recorded in MUSIC JUKE by group such
as name, genre etc. The display and playback order of playlists and tracks may differ
depending on the play mode chosen.
● The table below shows play modes with corresponding display and playback orders.
PLAY MODEPlaylist display/playback order
ALBUM
MY SELECTION
TRACK
ARTIST
GENRE
DATE
playlist names, track names, and other details recorded in MUSIC JUKE can be
displayed. Up to 28 characters can be shown in the display.
Automatically created playlists displayed/played back in reverse
chronological order (newest on top)
Original playlists displayed/played back in reverse chronological order
(newest on top)
Displays all recorded music.
Automatically created playlists displayed/played back in alphabetical order
Displayed/played back in preset order
Automatically created playlists displayed/played back in reverse
chronological order (newest on top)
JUKE
MUSIC
83
Page 85
How to operate MUSIC JUKE
How to use MUSIC JUKE
● The table below shows display and playback orders for tracks.
PLAY MODETrack display/playback order
ALBUM
MY SELECTION
TRACK
ARTIST
GENRE
DATE
*: When all the tracks for the same ARTIST/GENRE have been played, MUSIC JUKE
switches to the next ARTIST/GENRE.
Selecting with track selection (track start point) button
Tracks displayed/played back in the same order as they are recorded on the
music CD.
Tracks displayed/played back in the order they were added to the playlist
Tracks displayed/played back in chronological order (oldest recorded track
on top)
Tracks displayed/played back in the same order as they are recorded on the
music CD.*
Tracks displayed/played back in the same order as they are recorded on the
music CD.*
Tracks displayed/played back in chronological order (oldest recorded track
on top)
84
Touch and select
PLAY MODE
play mode.
● When play mode is switched, the first
playlist recorded in the selected mode
is played.
● If MUSIC JUKE was last used for
playback, the playlist listened to most
recently will be played.
● Each time is
touched, the play mode will be
changed in the order shown below.
ALBUMMY SELECTION
DATEGENRE
Play modes cannot be selected if there are no playlists created for that mode.
PLAY MODE
TRACK
ARTIST
Page 86
Touch or
● Displays/plays back track information
PLAYLIST
PLAYLIST
for the first track recorded in the
playlist.
to select a playlist.
Press or to select a track.
● Switches/plays back tracks recorded in
the playlist in order.
Selecting with Play mode/Playlist change switch
Touch .
● The playlist screen appears.
PLAYLIST
Touch a play mode.
● Displays the playlists recorded in that
play mode.
● When the ARTIST or GENRE play
mode has been selected, a list of
album names for each artist/genre can
be displayed.
● Touch to display a list of all
TRACK
tracks recorded in MUSIC JUKE.
●PLAYLIST screen
JUKE
MUSIC
Continue to the next page
85
Page 87
How to operate MUSIC JUKE
How to use MUSIC JUKE
Touch a playlist.
● When an artist or genre playlist has
been selected, touch to
display a list of album names assigned
to that artist/genre.
To u ch .
● Displays a list of the tracks in the
● Touch to start playback from the
TRACK
selected playlist.
first track recorded in the playlist.
ALBUM
Touch a track (song) name.
● Plays the selected track.
PLAYLIST
86
●Track list screen
●When there are 4 or more playlists in the same play mode, touch or to
switch to playlists that are not displayed.
●When there are 4 or more tracks (songs) in the same playlist, touch or to
switch to track names that are not displayed.
Page 88
Fast-forwarding/rewinding
It is possible to fast-forward/rewind in the track (song) being played.
Press and hold or until you hear a beep.
● (up) : Fast-forward
(down) : Rewind
The deck switches to fast-forward (rewind) mode when you hear a beep and continues
fast-forwarding (rewinding) until you remove your finger from the button.
Searching for a track (song)
Searching for a track (song) from a playlist
To u ch .
To u ch .
● The system will play the first 10 seconds of each track located within the current
FUNC
SCAN
playlist. Touch again to continue playing the current track.
SCAN
Searching for a playlist from a play mode
To u ch .
Touch .
● The system will play the first 10 seconds of the first track of each playlist located within
FUNC
PLAYLIST SCAN
the current play mode. Touch again to continue playing the
current playlist.
PLAYLIST SCAN
JUKE
MUSIC
87
Page 89
How to operate MUSIC JUKE
How to use MUSIC JUKE
Repeating a track (song)
Repeating the current track
To u ch .
To u ch .
● Repeats the current track.
● The track will repeat until the function is canceled. Touch again to cancel.
FUNC
RPT
RPT
Repeating the current playlist
To u ch .
To u ch .
● Touch once to continue repeating the playlist. Repeat will continue
FUNC
PLAYLIST RPT
PLAYLIST RPT
until canceled. Touch
PLAYLIST RPT
again to cancel.
Playing tracks (songs) in random order
Play tracks in current playlist in random order
To u ch .
To u ch .
● Plays tracks in randam order.
● Random playback will continue until the function is canceled. Touch again to
FUNC
RAND
RAND
cancel.
88
Playing all tracks recorded in MUSIC JUKE in random order
To u ch .
Touch .
● Touch to play all recorded tracks in random order. Random playback
● The track to be played next is randomly selected at the end of the current track. As a
FUNC
ALL RAND
ALL RAND
will continue until canceled. Touch again to cancel.
result, it is possible for the same track to be played multiple times in a row.
ALL RAND
Page 90
Turning MUSIC JUKE off
PWR
Press .
● Press again to resume playback.
PWR
JUKE
MUSIC
89
Page 91
How to operate MUSIC JUKE
4. Editing a playlist
Music recorded into MUSIC JUKE is grouped into automatically created playlists according to
album name, artist name etc. However, it is also possible to create original playlists containing
a collection of your preferred tracks (songs). The playlist name can be edited and the playlist
order switched.
● Playback pauses while editing is in progress.
Creating a playlist
The MY SELECTION play mode allows you to create a playlist containing only your preferred
tracks. When creating a new playlist in the ARTIST play mode, see "Changing the artist"
(page 105).
To u ch .
Touch .
● The Edit menu screen appears.
FUNC
EDIT
To uc h
NEW CREATION (PLAYLIST)
Entering the playlist name
Touch .
● The character input screen appears.
TITLE
.
90
Page 92
Enter the title.
● See "Entering playlist name" (next
page) for information regarding
entering names.
Touch .
Adding a track to a created playlist
ENTER
Select a track.
● See "Track search" (page 103) for
information regarding track searching.
Touch .
ENTER
JUKE
MUSIC
●Always enter a track into a newly created playlist. A playlist cannot be created if it
does not contain at least one track.
●To select multiple tracks simultaneously, touch all of the relevant tracks.
●Up to 99 tracks can be selected at one time.
91
Page 93
How to operate MUSIC JUKE
Editing a playlist
Entering playlist name
Enter one letter at a time by
touching the switches on the
screen.
● Touch or (numeric/
● If you make a mistake (or if the name is
ABC12 #$
symbols) to switch to the
corresponding input screen.
already entered), touch to
delete one letter at a time.
.
CLEAR
Touch .
ENTER
92
●Up to 32 characters can be entered.
●The same name cannot be registered twice.
Page 94
Editing a playlist name
The names of playlists recorded in the ALBUM or MY SELECTION play modes can be edited.
To u ch .
Touch .
● The Edit menu screen appears.
To u ch .
Touch .
FUNC
EDIT
EDIT (PLAYLIST/TRACK)
PLAYLIST
JUKE
MUSIC
Touch or
ALBUM
MY SELECTION
.
Continue to the next page
93
Page 95
How to operate MUSIC JUKE
Editing a playlist
Touch the playlist you want to edit.
Touch .
● The character input screen appears.
TITLE
Enter the title.
● See "Entering playlist name" (page
92) for information regarding entering
names.
To u ch .
ENTER
94
Page 96
Retrieving title information from the database
If title information cannot be assigned during digital recording, or the assigned information is
incorrect, the relevant information will be searched from the database and assigned to the
track (song).
To u ch .
Touch .
● The Edit menu screen appears.
To u ch .
Touch .
FUNC
EDIT
EDIT (PLAYLIST/TRACK)
PLAYLIST
JUKE
MUSIC
Touch .
ALBUM
Continue to the next page
95
Page 97
How to operate MUSIC JUKE
Editing a playlist
Touch the playlist you want to edit.
To u ch .
● The display returns to the previous
When there are multiple sets of title information
SEARCH
screen once the title information has
been received.
Touch the relevant title.
● Up to 10 titles can be displayed.
● Touch to return to the
● Touch to display a list of track
BACK
previous screen without retrieving title
information.
INFO
(songs) names included in the title list.
After checking, touch to
retrieve the title information and return
to screen .
7
ENTER
96
Page 98
Switching playlist order
Playlists and tracks are displayed and played back in the order they were recorded. The
playback order can be changed by switching the way the playlist is displayed.
● Playlist order can only be changed if "PLAYLIST DISPLAY" is set to SELECT in MUSIC
JUKE setting screen. If "PLAYLIST DISPLAY" is set to SELECT, touch for
"PLAYLIST DISPLAY" as explained in "Switching to chronological order" (next page).
Reorder according to your own preference
SELECT
Touch .
PLAYLIST
Touch the preferred play mode.
Touch the preferred playlist.
To u ch .
● Playback of the tracks in the selected
playlist begins and the playlist display
switches.
JUKE
MUSIC
97
Page 99
How to operate MUSIC JUKE
Editing a playlist
Switching to chronological order
It is possible to return to chronological (starting from playlist created/recorded first) order after
having reordered according to your own preference.
To u ch .
Touch .
● MUSIC JUKE setting screen appears.
Touch in PLAYLIST
FUNC
SET
INITIAL
DISPLAY.
● Switches to chronological order.
98
Page 100
Deleting a playlist
Playlists recorded in the ALBUM or MY SELECTION play modes can be deleted. The data
deleted will differ depending on the selected play mode.
Selected play modeData that will be deleted
ALBUM
MY SELECTION
The selected playlist and tracks (songs) will be deleted and will no
longer appear as results even if searched for in a different play mode.
The selected playlist will be deleted but tracks will not. They will still
appear in results if searched for in a different play mode.
To u ch .
Touch .
● The Edit menu screen appears.
To u ch .
Touch .
FUNC
EDIT
DELETE
PLAYLIST
JUKE
MUSIC
Continue to the next page
99
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.