Ecler IC User Manual [en, de, es, fr]

INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES NOTICE D’EMPLOI BEDIENUNGSANLEITUNG

IC SERIES

INSTRUCTION MANUAL

1. IMPORTANT REMARK 04

2. WARNINGS 04

3. INTRODUCTION 04

4. CONNECTIONS 05

5. LOCATION AND ASSEMBLY 06

6. PAINTING 06

7. TECHNICAL CHARACTERISTICS 19

All numbers subject to variation due to production tolerances. ECLER, S.A. reserves the right to make changes or improvements in manufacturing or design which may affect specifications.

1. IMPORTANT REMARK

We thank you for trusting in us and choosing our IC-series spea k er f or f a l se c eilings.

- before you plug anything - to read this manual very carefully and bear in mind all considerations specified within it. We strongly recommend that its maintenance be carried out by our Authorized Technical services.

2. WARNINGS

for each application.

3. INTRODUCTION

in an easy-to-use design that is quick to install. They also provide excellent sound quality for high and low thanks to our infinite speaker philosophy and to top-performance high frequency transducer.

versatile and are easy to use both in applications with low impedance and in applications running at 100V/70V. All you have to do is shift the position of the built-in selector.

giving them maximum, long-term stability and protecting them from environmental factors like heat and humidity.

technical specifications of each of these models: IC5

Congratulations! You are the owner of a carefully designed and manufactured equipment. In order to get the optimum operation and efficiency from this unit, it is VERY IMPORTANT

Never use this unit in the proximity of water. Do not expose the unit to water splashing, nor place liquid containers on top of it. Avoid placing the unit next to heat sources such as spotlights or heaters.

Use only the accessories specified by the manufacturer, employing the correct accessories

ECLER's line of IC speakers for false ceilings incorporates carefully selected components

Because we have included a transformer in the whole series, our units are extremely

The transducers used to play low and medium frequencies are made of polypropylene,

There are three models in the IC series: IC5, IC6 and IC8. Here, we will describe the

• 2 way speaker for false ceilings

• 5” polypropylene woofer

• 13mm tweeter

• Power: 25W RMS@8Ω

• Sensitivity (1W/1m): 88 dB SPL

• Built-in transformer.

• External diameter: 191mm

• Cut out diameter: 168mm

• Installation system: Three revolving fasteners

IC6

• 2 way speaker for false ceilings

• 6.5” polypropylene woofer

• 25mm tweeter

• Power: 40W RMS@8Ω

• Sensitivity (1W/1m): 90 dB SPL

• Built-in transformer.

• External diameter: 204mm

• Cut out diameter: 180mm

• Installation system: Three revolving fasteners

IC8

• 2 way speaker for false ceilings

• 8” polypropylene woofer

• 25mm tweeter

• Power: 60W RMS@8Ω

• Sensitivity (1W/1m): 91 dB SPL

• Built-in transformer.

• External diameter: 245mm

• Cut out diameter: 222mm

• Installation system: Three revolving fasteners

Note: If you use the speaker for false ceiling in 70V installations, the power for the 100V position will be half the amount shown on the switch. When used in 50V installations, it will be a fourth of the amount.

included in the package. Be careful not to damage the speaker when removing the grill.

4. CONNECTIONS

model are clamps for stripped wires. Once they are connected, all you have to do is choose the unit's power and mode of operation using a simple screwdriver. Always pay attention to the polarity.

connected to a low-impedance amplifier, the speaker will not be damaged, but will perform way below its full potential. If the speaker is accidentally connected to a 100V/70V line in the 8Ω position, it will be severely damaged.

on how to install the units, please see section 5 of this manual.

Each model in the series comes with a protective grill that can be removed with a hook

The connection terminals for each

The IC series are shipped from factory with the sw itch in 100V/70V position. If it is

Use the three revolving fasteners included to easily install the units. For more information

5. LOCATION AND ASSEMBLY

would like to place the speakers and have the wiring necessary for each unit.

unit is separated into two parts, the outside part can be used as a template to make the hole in the ceiling, and the inner disk can be used to protect the speaker cone if you would like to paint the plastic another colour.

6. PAINTING

of the aesthetic criteria of the place where it will be used.

To install this product correctly, you must be prepared to cut circular holes where you

In order to install the speakers correctly:

1. Remove the protective grating from the speaker using the hook provided in the packaging.

2. Cut a circular hole in the false ceiling. A template for cutting/painting is included with each unit to simplify this process. Once the

3. Use the clamps to connect the unit to the wiring of the system where the speaker is being installed.

4. Place the speaker in the newly cut hole. Hold it in place with your hand and push it into place, all the while making sure that the three revolving fasteners are drawn back.

5. Press each of the thre e screws that are accessible from the front side of the speaker. The speaker is now fixed in its final position.

6. Reattach the protective grille.

The IC series is designed to be painted, meaning it can be installed anywhere, regardless

In order to paint any of the models in the product line:

1. Remove the protective grating from the speaker using the hook provided in the packaging.

2. Once the cut/paint template has been separated into two parts, use the inside disk to protect the speaker cone. Place it tight on the cone. The points still on disk after it has been separated help to fix it tight into place. The outside part of the template can be put on the back part of the speaker, lining it up with the plastic circle, to protect the back part from splattering if you are using spray paint.

3. Paint the protective grating and the speaker separately. Make sure that the small holes in the grating are not blocked by paint. Use an appropriate air-dry paint.

4. When the paint is dry, remove the protectors. The unit is ready to be installed.

+ 14 hidden pages