Echo Bear Cat 77000-00 User Manual

Instructions

3

SUBJECT: Two-Wheel Tow Kit,

PN 77000-00

MODELS: All 3" Chipper/Shredders,

except 70580 and SC3270T models

WARNING

Before inspecting or servicing any part of this machine,
shut off engine, disconnect the spark plug and make sure
all moving parts have come to a complete stop.

The tow kit adds two wheels and a tow bar to the standard
3-inch chipper/shredder so that it can be towed by a garden
tractor or ATV.

2. Remove two 5/16" flange nuts (3) and remove support
leg. Reattch axle (4) and wheels using the removed
flange nuts

3. Remove three 5/16" flange nuts (5).

5

INSTALLATION FOR SERIAL NUMBERS
C03478 AND ABOVE (FIGURE 1)

1. FOR 3-INCH CHIPPER/SHREDDERS C03478 AND
ABOVE

two 5/16 x 1-3/4" bolts (2), washers and nuts closest
to the chipper chute on the leg support.

, remove the metal leg (1) by first removing the

Instruction Sheet

2

1

Figure 1. Leg removal, Chipper/Shredder C03478 and above

4

NOTE

Before cutting off the welded or removing bolt-on support
leg, make sure machine is supported and secured to
prevent the machine from falling or tipping that could
result in injury

PN 77001-00

Rev. 080112

4

SC3265 MODEL SHOWN

INSTALLATION FOR SERIAL NUMBERS 707865
TO C03262 (FIGURE 2)

1. FOR 3-INCH CHIPPER/SHREDDERS SN 707865 TO C03262,

remove the metal leg (1) by removing the four 5/16" nuts
(2) and washers. Also remove the nut and washer from
the middle lower bolt.

2. Keep and reuse all of the nuts (2) and washers; Discard
the metal leg.

2

1

NOTE

If you have an older model chipper/shredder, you will
have to cut off the existing metal leg before installing the
kit. Newer models have a detachable leg. Choose the
instructions below that are appropriate for your machine

INSTALLING THE KIT

1. Lay tow kit assembly (6), on a flat working surface.

2. Attach tow bar weldment (7), to the tow kit assembly (6)
using 3/8 x 2" bolt (1) and lock nut. Tighten securely.

3. Attach the tow bar (5), to the assembly using the
remaining 3/8 x 2" bolt (1) and lock nut (3).

4. Install the wheels (4) using 5/8 x 3" bolts (2) and tighten
securely.

5. Attach hitch assembly to the machine by placing the hitch
on the three lower bolts on the housing and securing with
the three nuts and washers or flange nuts removed in
the previous steps.

Figure 2. Leg removal, 3" Chipper/Shredder 707865 to C03262

INSTALLATION FOR SERIAL NUMBERS 707807
AND BELOW (FIGURE 3)

1. FOR 3-INCH CHIPPER/SHREDDERS SN 707807 AND
BELOW

appropriate for cutting metal. Make the cut approximately
1/4" - 1/2" from the chipper frame.

2. Discard metal leg.

3. Remove the three 5/16" nuts (2) and washers.

2

Figure 3. Leg removal, 3" Chipper/Shredder 707807 and below

, cut the leg (1) off with a hacksaw or other saw

1

Phone: [phone] • Toll Free: 800.247.7335 • Fax: [phone]

E-mail: [e-mail] • [e-mail]

5

4

2

1

3

1

3

6

2

7

PARTS LIST, KIT NO. 77001-00

ITEM PART NO. DESCRIPTION QTY

1 15008 BOLT, 3/8 X 2 HEX HD GR5 ZP 2

2 15019 BOLT, 5/8 X 3 HEX HD GR5 ZP 2

3 15388 NUT, 3/8 NE NYLOCK ZP 2

4 16003 WHEEL ASSY, 410/350-4 2

5 75608-12 WELDMENT, TOW BAR 1

6 76996-00 ASSEMBLY, TWO WHEEL TOW KIT 1

7 76999-12 WELDMENT, TOW BAR 1

237 NW 12th Street, West Fargo, ND 58078-0849

www.bearcatproducts.com

ECHO BEAR CAT