Echo Bear Cat 76854 User Manual

Orchard Chipper

Hinged cover provides quick access
to the chipper blades.

16 reversible chipper blades produce
the smallest chips in the industry.

9" Capacity

Model 76854

Standard

Bear Cat

Seeing is believing! Compare the sizes
above. The new 76854 achieves the
smallest chips possible.

Low profile discharge places chips
directly onto the ground.

Orchard
Chipper

Model 76854

Model Engine Size Chipper Feed Feed Weight 3 Point PTO
LxWxH) Capacity System Opening (Lbs.) Hitch

76854 PTO 69"x50"x93" 9" hydraulic 9"x9" 1300 Cat. 1 540 rpm



16 reversible chipper blades.



Low profile discharge places the
chips directly onto the ground.



Multiple positions available
for 8" discharge chute.



Self-contained hydraulic feed
system.



LOFA speed control system is



a standard factory-installed

Hinged service cover.

feature.

Find a dealer near you!

Call us at 800.247.7335 or

Log onto www.BearCatProducts.com

Email: [e-mail] • Fax: [phone]

A Breed Above the Best

9" Orchard Chipper Specs

Model 76854

30" [76CM] DIAMETER DISC

• Thirty inch diameter by 1.25" [3.175cm] thick disc

that weighs 275 lbs. [125kg]

• Balanced for smooth operation.

• Disc turns at 1500 RPM.

16 CHIPPING BLADES

• Spaced on the disk to provide maximum coverage

and produce an extremely small chip

FOUR EDGE ADJUSTABLE ANVIL

• To insure good chipping ability.

• 9.25" long X 3.5" wide X .625" thick.
[23.5cm x 8.9cm x 1.6cm]

EASY ACCESS DISC

• The disc is accessible through the hinged disc

cover, which exposes one-half of the disc for easy
access to the chipping blades and for easy clean
out.

INTEGRATED DISCHARGE BLOWER

• Put the chips where you want them, directly

onto the ground.

• Position the chute in multiple positions.

• Low profile discharge chute prevents chips from
damaging branches.

BEARINGS

• Two 1.75" [4.45cm] greasable bearings with 4
bolt cast flanges.

FEED CHUTE

• Opening 30.25" X 30.75" [76.8cm x 78.1cm],

tray 28.31" [71.9cm] off the ground.

• Feed table is 38" [96.5cm] long.

FEED THROAT

• 9" X 9" [22.86cm x 22.86cm]

90° FEED ANGLE

• Quicker chipping because you are cutting
through less wood.

MAXIMUM FEED SIZE

• 9" [20cm] for model 76854

FEED SYSTEM

• Self-contained with infinate feed rate settings.

• Single 15" [38cm] diameter feed roller with feed
rate of 0-150fpm [0-45 meters/min].

• 45 cu. in. [737cc] hydraulic motor.

• 1750 psi [119 atm] operating pressure.

FOLD DOWN FEED TRAY IS
STANDARD ON #76854

• Extends feed table by 30" [76.2cm].

HEAVY-DUTY CONSTRUCTION

• .375" [9.5mm] thick steel face plate on the disc

housing;

• .25" [6.35mm] thick steel on the wrap around
with welded construction

SAFETY

• Meets all applicable ANSI safety standards.

A Breed Above the Best

ELECTRONIC FEED SENSOR
AND HOUR METER

• Digital, programmable electronic feed sensor with
hour meter. Hour meter has readout of total hours
and daily hours.

Find a dealer near you!

Call us at 800.247.7335 or

Log onto www.BearCatProducts.com

P.O. Box 849, West Fargo, ND 58078

Email: [e-mail] • Fax: [phone]