Echo SHC-2401 Operator's Manual
Shaft Hedge Clipper
Operator's Manual
MODEL: SHC-2401
Serial Number 001001 & Up
S
HAFT HEDGE CLIPPER
O
PERATOR'S MANUAL
1
W ARNING DANGER
Always keep clear of exhaust and muffler area,
otherwise serious personal injury may occur.
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual
and a Safety Manual. Both must be read and understood for proper and safe operation. Failure to
do so could result in serous injury.
X7502251700
The muffler or catalytic muffler
and surrounding cover may become
extremely hot.
WARNING DANGER
WARNING
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects or other
reproductive harm.
X750000920
02/00
2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-jobdependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operating tips and SAFETY messages.
W ARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual.
Both must be read and understood for proper and safe operation.
THE OPERATOR'S MANUAL
contains specifications and information for operation, starting,
stopping, maintenance, storage and assembly specific to this
product.
THE SAFETY MANUAL
explains possible hazards involved with the use of Hedge
Clippers and what measures you should take to make their use
safer.
--
--
TABLE OF CONTENTS
Introduction ........................................................................ 2
- The Operator's Manual .............................................. 2
- The Safety manual ...................................................... 2
Manual Safety Symbols and Important Information ......... 3
Safety.................................................................................. 3
- General Description.................................................... 3
- Decals ......................................................................... 4
- International Symbols................................................. 4
- Equipment .................................................................. 5
- Fuel ............................................................................. 5
- Personal Condition and Safety Equipment................. 6
- Safe Operation ............................................................ 7
- Extended Operation/Extreme Conditions ................... 8
Description ......................................................................... 9
- Contents ..................................................................... 9
- Emission Control ........................................................ 9
Specifications.................................................................... 12
Assembly.......................................................................... 13
- Gear Housing / Drive Shaft....................................... 13
- Power Head / Drive Shaft ......................................... 13
- Throttle Linkage and Ignition Leads ......................... 13
Pre-Operation ................................................................... 14
- Fuel ........................................................................... 14
- Equipment Check ..................................................... 15
- Determine Operation Area ....................................... 15
Operation.......................................................................... 16
- Starting Cold Engine ................................................. 16
CopyRight© 1999 By Echo, Incorporated
All Rights Reserved.
- Starting Warm Engine ................................................ 17
- Stopping Engine ........................................................ 18
Maintenance ..................................................................... 18
- Skill Levels ................................................................ 18
- Maintenance Intervals ............................................... 19
- Air Filter.................................................................... 20
- Fuel Filter .................................................................. 20
- Spark Plug ................................................................. 21
- Cooling System Cleaning........................................... 21
- Exhaust System ......................................................... 22
- Carburetor Adjustment ............................................. 23
- Lubrication ................................................................ 24
- Sharpening Blades ..................................................... 25
Troubleshooting................................................................ 26
Stor age .............................................................................. 27
Servicing Information........................................................ 28
- Parts .......................................................................... 28
- Service ....................................................................... 28
- ECHO Consumer Product Support.......................... 28
- Warranty Card........................................................... 28
- Additional or Replacement Manuals......................... 28
- Manual Ordering Instructions ................................... 28
Specifications, descriptions and illustrative material in this
literature are as accurate as known at the time of
publication, but are subject to change without notice.
Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
S
HAFT HEDGE CLIPPER
O
PERATOR'S MANUAL
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key
words and what they mean to you.
IMPORTANT
3
This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can lead
to serious personal injury to operator and bystanders.
The circle with the slash symbol means whatever is shown
within the circle is prohibited.
IMPORTANT The enclosed message
provides information necessary for the
protection of the unit.
NOTE This enclosed message provides
tips for use, care and maintenance of the
unit.
SAFETY
GENERAL DESCRIPTION
IMPORTANT
See Description and Specification sections for full description and illustration of model variation in power head,
and handle type.
NOTE
DOUBLE SIDED
HEDGE CLIPPER
BLADES
GEAR
HOUSING
DRIVE SHAFT
HOUSING
LEFT FRONT
HANDLE GRIP
SAFETY DECAL
POWER HEAD
STOP
SWITCH
THROTTLE
TRIGGER
4
DECALS
Locate these safety decals on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help
you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal
cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific
information.
DRIVE SHAFT DECALS
INTERNATIONAL SYMBOLS
Symbol form/shape
Symbol
description/application
Read and understand
Operator's Manual.
Wear eyes, ears and
head protection
Wear slip resistant
foot wear.
Hot
Surface
Safety/Alert
Symbol form/shape
Symbol
description/application
Fuel and oil mixture
Finger Severing
Hazard
Wear hand
protection. Use
two handed.
DO NOT smoke
near fuel.
DO NOT allow
flames or sparks
near fuel.
Symbol form/shape
Symbol
description/application
Avoid all power lines.
This unit is not insulat-
ed against electrical
current.
Keep bystanders at
least 15 meters
(50 feet) away.
Engine choke
control.
Primer bulb
Carburetor adjustment
- Low speed mixture
Symbol form/shape
Symbol
description/application
Do not operate clos-
er than 15 M (50 ft.)
from electrical
hazards.
Emergency stop
Ignition
ON/OFF
Carburetor adjustment
- High speed mixture
Carburetor adjustment
- Idle speed
EQUIPMENT
Before operation a complete check of the unit must be performed;
• Check unit for loose/missing nuts, bolts and screws. Tighten
and/or replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
• Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades should not be used.
S
HAFT HEDGE CLIPPER
O
PERATOR'S MANUAL
5
FUEL
W ARNING DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing or
handling, otherwise serious personal injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel
capsslowly allowing pressure to equalize.
• NEVER refuel a unit when the engine is HOT!
• NEVER refuel a unit with the engine running.
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors
over bare ground.
• Securely tighten fuel cap after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers to
reduce fuel spillage. Contact your ECHO dealer for ordering
information.
After Refueling;
• Wipe any spilled fuel from the unit.
• Move at least 3 M (10 ft.) from refueling location before starting.
After Use;
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
3 M (10 ft.)
6
PERSONAL CONDITION AND SAFETY EQUIPMENT
W ARNING DANGER
Hedge Clipper users risk injury to themselves and others if the shaft hedge clipper is used improperly and or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating a shaft hedge clipper.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE requirements
whenever you operate the unit.
Face & Head Protection
When trimming overhead, wear head protection meeting ANSI Z89.1
with a full face shield.
Hand Protection —
Wear no-slip, heavy duty work gloves to improve your grip on the
unit handles. Gloves also reduce the transmission of machine vibration
to your hands.
Hearing Protection —
Wear hearing protection. ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing —
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY.
Wear sturdy work shoes with non-skid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Hot Humid Weather —
Heavy protective clothing can increase operator fatigue which may lead
to heat stroke. Schedule heavy work for early morning or late afternoon
hours when temperatures are cooler.
SAFE OPERATION
Determine Operation Area
• Provide all operators of this equipment with the Operator's Manuals
and instructions for safe operation.
• Review the area to be trimmed. Look for hazards that could contribute
to unsafe conditions. DO NOT operate unit if any wires (power,
telephone, cable, etc.) are closer than 4.5 M (15 ft.) to any part of the
operator or unit.
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 M (50 ft.) while the
Hedge Clipper is in use.
Operation
Use Proper Clothing & Equipment
• Before starting the unit, equip yourself and any other person
working within the 15 M (50 ft.) Safety Zone with the required
Protective Equipment and clothing.
S
HAFT HEDGE CLIPPER
O
PERATOR'S MANUAL
7
W ARNING DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
Avoid Hot Surfaces
• During operation, the complete unit, especially the drive shaft
housing, power head, muffler area and gear box may become very
hot, too hot to touch. Avoid contact during and immediately after
operation.
Keep A Firm Grip
• Hold the front and rear handles with both hands with thumbs and
fingers firmly encircling the handles
Keep A Solid Stance
• Maintain footing and balance at all times. Do not stand on
slippery, uneven or unstable surfaces. Do not work in odd
positions or on ladders. Do not over reach.
8
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended because the minimum exposure which might trigger the
ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the trimmer or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended or twisted position.
Instead try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive
movement.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness or pain in the fingers, hands, wrists or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
S
HAFT HEDGE CLIPPER
O
PERATOR'S MANUAL
DESCRIPTION
The ECHO product you have purchased has been factory pre-assembled for your convenience. Due to packaging
restrictions, some assembly of the SHC-2401 is required.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
CONTENTS LIST
__ 1 - Shaft Hedge Clipper Assembly
__ 1 - Power Head Assembly
__ 1 - Gear Housing Assembly
__ 1 - Operator's Manual
__ 1 - Hedge Clipper Safety Manual
__ 1 - Warranty Statement
__ 1 - Warranty Registration Card
__ 1 - 2-Stroke Oil Sample, 2.6oz.
__ 1- 3mm Hex Wrench
__ 1 - 4mm Hex Wrench
__ 1 - 8mm/10mm Wrench
__ 1 - Blade Cover
__ 1 - Safety Glasses
9
EMISSION CONTROL
The emission control system for this engine is EM (Engine Modification).
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY: YEHXS.0254CB
DISPLACEMENT: 25.4 CC
THIS ENGINE MEETS U.S. EPA PH1 EMISSION
REGULATIONS FOR SMALL NON ROAD ENGINES.
REFER TO OWNER'S MANUAL FOR MAINTENANCE
SPECIFICATIONS AND ADJUSTMENTS.
An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by engine
FAMILY).
Loading...