ebm-papst M3G084-FA33-82 User Manual

M3G084-FA33-82

Operating instructions

ebm-papst Mulfingen GmbH & Co. KG

Bachmühle 2
D-74673 Mulfingen
Phone [phone]
Fax [phone]
[e-mail]
www.ebmpapst.com

CONTENTS

CAUSES AND REMEDIES

Translation of the original operating instructions

1. SAFETY REGULATIONS AND NOTES

Please read these operating instructions carefully before starting to work
with the device. Observe the following warnings to prevent malfunctions
or physical damage to both property and people.
These operating instructions are to be regarded as part of this device.
If the device is sold or transferred, the operating instructions must
accompany it.
These operating instructions may be duplicated and forwarded for
information about potential dangers and their prevention.

11. SAFETY REGULATIONS AND NOTES

11.1 Levels of hazard warnings

11.2 Staff qualification

11.3 Basic safety rules

11.4 Electrical voltage

21.5 Electromagnetic radiation

21.6 Mechanical movement

21.7 Hot surface

21.8 Transport

21.9 Storage

21.10 Disposal

32. PROPER USE

43. TECHNICAL DATA

43.1 Product drawing

53.2 Nominal data

53.3 Technical features

53.4 Mounting data

53.5 Transport and storage conditions

53.6 Electromagnetic compatibility

64. CONNECTION AND START-UP

64.1 Connecting the mechanical system

64.2 Connecting the electrical system

64.3 Connection in terminal box

74.4 Factory settings

84.5 Connection screen

94.6 Checking the connections

94.7 Switch on device

94.8 Switching off the device

95. INTEGRATED PROTECTIVE FUNCTIONS

106. MAINTENANCE, MALFUNCTIONS, POSSIBLE

106.1 Cleaning

106.2 Safety test

1.1 Levels of hazard warnings

These operating instructions use the following hazard levels to indicate
potentially hazardous situations and important safety regulations:

DANGER

Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury. Compliance with
the measures is mandatory.

WARNING

Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury. Exercise extreme
caution while working.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury or damage of property.

NOTE

A potentially harmful situation can occur and, if not avoided, can
lead to property damage.

1.2 Staff qualification

Only specialised electrical personnel may install the device, perform the
test run and work on the electrical system.
Only trained and authorised specialist personnel are permitted to
transport, unpack, assemble, operate or maintain the device, or to use it
in any other manner.

1.3 Basic safety rules

Any safety hazards stemming from the device must be re-evaluated
once it is installed in the end device.
Observe the following when working on the unit:

; Do not make any modifications, additions or conversions to the

device without the approval of ebm-papst.

1.4 Electrical voltage

; Check the electrical equipment of the device at regular intervals, refer

to chapter 6.2 Safety test.

; Replace loose connections and defective cables immediately.

DANGER
Electrical load on the device

Risk of electric shock

→ Stand on a rubber mat if you are working on an electrically

charged device.

CAUTION
In the event of failure, there is electric voltage at the
rotor and impeller

The rotor and impeller are base insulated.

→ Do not touch the rotor and impeller once they are installed.

Item no. 50845-5-9970 · Revision 79932 · Release 2013-04-18 · Page 1 / 10

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone [phone] · Fax [phone] · [e-mail] · www.ebmpapst.com

M3G084-FA33-82

Operating instructions

CAUTION
If control voltage is applied or a speed setpoint is stored,
the motor automatically restarts, e.g. after a power failure.

Danger of injury

→ Keep out of the danger zone of the device.

→ When working on the device, switch off the mains

supply voltage and secure the latter from being switched on
again.

→ Wait until the device stops.

→ After working on the device, remove any used tools or

other objects from the device.

CAUTION
The motor restarts automatically when operating voltage
is applied, e.g. after a power failure.

Danger of injury

→ Keep out of the danger zone of the motor.

→ When working on the motor, switch off the mains supply

voltage and secure the latter from being switched on again.

→ Wait until the motor stops.

1.5 Electromagnetic radiation

Interference from electromagnetic radiation is possible, e.g. in conjunction
with open and closed-loop control devices.
If unacceptable emission intensities occur when the fan is installed,
appropriate shielding measures have to be taken by the user.

NOTE
Electrical or electromagnetic interferences after
integrating the device in installations on the customer's
side.

→ Verify that the entire setup is EMC compliant.

1.6 Mechanical movement

WARNING
Rotating device

Long hair, loose items of clothing and jewellery could become
entangled and pulled into the device. You could be injured.

→ Do not wear any loose clothing or jewellery while working

on rotating parts.

→ Protect long hair by wearing a cap.

WARNING
Flying parts

If the motor is operated with attached fan blades, missing safety
devices may cause balancing weights or broken fan blades to
be ejected and cause bodily injuries.

→ Take the appropriate safety measures; e.g. install guard

grilles.

→ Keep out of the exhaust zone.

1.7 Hot surface

CAUTION
High temperature at the electronics enclosure

Danger of burn injuries

→ Ensure that sufficient protection against accidental contact is

provided.

1.8 Transport

CAUTION
Transport of motor

Crushing hazard

→ Wear safety shoes and cut-resistant safety gloves.

→ Transport the motor in its original packaging only.

→ Secure the device so that it does not slip, e.g. by using a

clamping strap.

1.9 Storage

; Store the device, partially or fully assembled, in a dry and

weatherproof manner in the original packing in a clean environment.

; Protect the device from environmental impacts and dirt until the final

installation.

; We recommend storing the device for a maximum up to one year to

guarantee proper operation and longest possible service life.

; Even devices explicitly suited for outdoor use are to be stored as

described prior to being commissioned.

; Maintain the storage temperature, see

chapter 3.5 Transport and storage conditions.

; Please make sure that all screwed cable glands are fitted with

dummy plugs.

1.10 Disposal

When disposing of the device, please comply with all relevant
requirements and regulations applicable in your country.

Translation of the original operating instructions

Item no. 50845-5-9970 · Revision 79932 · Release 2013-04-18 · Page 2 / 10

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone [phone] · Fax [phone] · [e-mail] · www.ebmpapst.com

M3G084-FA33-82

Operating instructions

2. PROPER USE

The device is designed exclusively for use as a drive motor.
Any other or secondary use is deemed improper and constitutes a
misuse of the device.
Installations on the customer's side must meet the mechanical, thermal
and service life-related stresses that can occur.

Proper use also includes:

● Using the device in accordance with the permitted ambient

temperature, see chapter 3.5 Transport and storage conditions and
chapter 3.2 Nominal data.

● Operating the device with all protective features in place.

● Minding the operating instructions.

Improper use

Using the device in the following ways is particularly prohibited and
may cause hazards:

● Opening the terminal box during operation.

● Moving air that contains abrasive particles.

● Moving highly corrosive air, e.g. salt spray mist. Exceptions are

devices that are intended for salt spray mist and protected accordingly.

● Moving air that contains dust pollution, e.g. suctioning off saw dust.

● Operating the device close to flammable materials or components.

● Operating the device in an explosive atmosphere.

● Using the device as a safety component or for taking on safety-

related functions.

● Operation with completely or partially disassembled or modified

protective features.

● In addition, all application options that are not listed under proper use.

Translation of the original operating instructions

Item no. 50845-5-9970 · Revision 79932 · Release 2013-04-18 · Page 3 / 10

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone [phone] · Fax [phone] · [e-mail] · www.ebmpapst.com