Ebac CD30, CD30E Owner's Manual
Page 1 of 12
Drawing : - TPC226
Issue : - 9
Date : - 10/11/14
CD30 / CD30E
INDUSTRIAL DEHUMIDIFIER
OWNER’S MANUAL
www.eipl.co.uk
Page 2 of 12
Drawing : - TPC226
Issue : - 9
Date : - 10/11/14
CD30
PACKAGE CONTENTS
Item Description Quantity
1133500 Dehumidifier 1
3014338 PVC tube – 12mm I/D 3 M
3086101 Jubilee clip 1
TPC226 Manual 1
CD30E
PACKAGE CONTENTS
Item Description Quantity
1133500 Dehumidifier 1
1139504 Wall mount bracket 1
3082214 Brass wood screw 3
3088525 Rawl plug 3
3014338 PVC tube – 12mm I/D 3 M
3086101 Jubilee clip 1
TPC226 Manual 1
Page 3 of 12
Drawing : - TPC226
Issue : - 9
Date : - 10/11/14
UNPACKING
Carefully remove the CD30 dehumidifier unit from its transit box and visually
check for signs of transit damage. If there is evidence of damage DO NOT
attempt to operate the unit, call your supplier for advice. Do not discard the
packing; it will be useful when transporting the dehumidifier unit in the future.
INTRODUCTION
The Ebac CD30 industrial dehumidifier removes moisture from the air through
the refrigeration process.
The Ebac CD30 is basically comprised of:
A) A compressor
B) A refrigerant evaporator coil
C) A refrigerant condenser coil
D) One circulation fan
E) A drain tray for collecting and disposing of condensed moisture
F) A solid state timer for hot gas defrost cycle
G) An adjustable membrane-type humidistat
H) A cabinet to house the above components
The fan draws the moist air through the cold evaporator coil which cools the
air below its dew point. Moisture forms on the evaporator coil and is collected
in the condensate tray which is equipped with a permanent drain. The cooled
air then passes through the hot condenser coil where it is reheated using the
same energy removed during the cooling phase plus the additional heat
generated by the compressor. The air is, therefore discharged from the
dehumidifier at a slightly higher temperature with a lower absolute humidity,
than that which entered. Continuous circulation of air through the dehumidifier
gradually reduces the relative humidity within the area.
The CD30 dehumidifier is a rugged reliable drying unit designed to operate
effectively over a broad range of temperature and humidity conditions. A
powerful and reliable active hot gas defrost system, controlled by an
electronic timer, guarantees positive de-icing, thereby optimizing operation at
low temperatures.
The unit incorporates a welded steel chassis and is finished in an epoxy
coating for resilience to damage caused by rough handling.
The CD30 dehumidifier is fitted with an adjustable humidistat to enable you to
select the level of dryness.
Page 4 of 12
Drawing : - TPC226
Issue : - 9
Date : - 10/11/14
SPECIFICATIONS
"This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. The
refrigeration system is hermetically sealed.
The Global Warming Potential (GWP) of refrigerants used in products manufactured by Ebac
Industrial Products Ltd is as follows
R134a – 1300
R407c – 1610
For type and weight of refrigerant contained in this unit, please refer to the product data label"
M
ODEL
: CD30 / CD30E
H
EIGHT
: 12”
W
IDTH
: 12”
D
EPTH
: 22”
W
EIGHT
:
CD30 – 50 lbs
CD30E - 55 lbs
A
IRFLOW
: 170 CFM
M
AX OPERATING TEMP
: 95ºF
P
OWER SUPPLY
: 110V, 60Hz
C
URRENT
:
CD30 – 4 A
CD30E – 5 A
R
EFRIGERANT TYPE
: R134a
Loading...