Precision GetFit
Digital Body Fat Bathroom Scale
Health Tools LLC
Mahwah, NJ 201-465-4381
INTRODUCTION
Thank you for purchasing the EatSmart Precision GetFit Bathroom Scale.
The EatSmart Precision GetFit Bathroom Scale is engineered and designed to provide accurate weight measurements and help you monitor body fat, body water, muscle mass and bone mass. The touch screen interface and automatic person identifier make it one of the most user friendly bathroom scales on the market today.
Your EatSmart GetFit Bathroom Scale comes with the following:
•EatSmart GetFit Digital Body Fat Scale
•Instruction Manual
•4 AAA batteries
•2 Year EatSmart Guarantee
Please read this instruction manual carefully before use.
Please fill out your purchase information for future reference:
Date Purchased:………………………………………………………………….
Place Purchased:………………………………………………………………….
Order ID (if any)…………………………………………………………………..
If you have any questions regarding the operation of your GetFit Bathroom Scale, please call 201-465-4381 from 9:00 AM to 5:00 PM, Monday through Friday, Eastern Standard Time or email support@eatsmartproducts.com anytime.
ABOUT THE GETFIT DIGITAL BODY FAT SCALE
Your GetFit Bathroom Scale uses BIA (bio-electrical impedance analysis) technology to calculate body fitness.
In bare feet, this technology sends a low-level electrical signal through your body and then measures the resistance the signal encounters. This signal is perfectly safe and will not be felt. The lower the body fat, the faster the signal will travel.
You will be given a final reading of your weight, % body fat, % total body water, % muscle mass and bone mass. This scale stores up to 8 different users’ personal profiles and will be able to recognize these users as soon as they step onto the scale, after the initial setup.
Precaution: People with implanted medical devices, such as pacemakers, metal plates/ screws or contraceptive appliances should not use this device. If in doubt, consult your physician. This analyzer is not intended for children under the age of 10 and pregnant women.
WHEN TO USE THE DIGITAL BODY FAT SCALE
To receive the most accurate weight measurement, please weigh yourself first thing when you get up in the morning.
To receive the most accurate body fat, total body water, muscle mass and bone mass measurement, please weigh yourself in the evening, before eating.
To receive the most accurate results, please remove all articles of clothing Stepping on the scale with shoes, socks or slippers will display your weight only.
Factors such as eating, drinking, showering, exercise, very dry or very wet feet or menstruation may vary your results, so try to keep these factors consistent when you compare your fitness results.
CONSISTENCY IS KEY WHEN TAKING YOUR READINGS!
HOW TO OPERATE YOUR GETFIT SCALE
Before First Use
1.Inserting Batteries and Selecting Measurement Unit
a)Open the battery compartment door on the back of the scale.
b)Put the batteries in, flat end against the spring. The LCD will display.
|
|
|
|
|
c) Close the battery door and wait until |
|
is shown on the LCD. |
||
d)Press “UNIT” button (located underneath scale) to select the desired measurement unit; pounds, kilograms, or stones. To set the scale to pounds, you want the display to read lb only (not st lb for stone pounds – a British measurement system). The default setting is pounds.
Weight Operation Instruction Only
1. Calibration
Place the scale on a hard, flat surface. After placing the scale down the display may read ~4 lbs briefly then it will go to 0 (zero). If you do not see the 4 lbs briefly register, press down on the scale platform to activate the backlight, get off, and wait for it to shut off. You can then step on the scale and get an accurate reading.
2. Weight Reading
Step on the scale, placing both feet evenly on each side and standing as still as possible. After a few seconds, you will see the weight flash three times to indicate a weight reading has been calculated.
Your Precision GetFit operates via “Step-On” technology but still needs to be calibrated upon first use or after the scale is moved to ensure accuracy.
After installing batteries, immediately place the scale on solid, flat surface (avoid carpet or softer flooring).
1.If the scale is on when it is placed on the floor you should see the scale read ~4lbs for 3 seconds then go to 0.0. Your scale is now calibrated and ready for use
2.If the scale does not turn on when placed down press the glass platform with one foot to turn the scale on (but do not step on fully). Allow the scale to go to 0.0 and turn off.
Note: When you pick up the scale, move the scale or replace batteries, the scale may lose calibration. You can either recalibrate (see above) or disregard the first weight after the scale is moved.
Fitness Mode Operation Instruction
1.Setting up Your Personal Profile
The GetFit Scale can store personal user profiles for up to eight users. Before doing a body composition analysis you must first set up a user profile.
a) Touch “SET” to turn scale on. The profile number will flash.
Note: If scale is already turned on, touch “SET” and hold for 2 seconds.
b)The profile number will flash. Touch 
or 
to select a desired profile number. Touch “SET” to confirm.
c)The gender icon will flash. Touch 
or 
to select user gender. The options are male, female, athletic male and athletic female. Touch “SET” to confirm
Note: Due to muscle mass and hydration levels, the body type of an athletic adult physiologically differs from that of a standard adult. Choose athletic mode if you exercise +15 hours of strenuous/ aerobic activity per week.
Our definition of an athlete also includes those who have been consistently working out for years but currently do not hit the 15 hr/week mark.
If you recently starting exercising +15 hrs/ week, it is recommended that you wait a minimum of 6 months before switching to athletic mode.
d)The value of height will flash. Touch 
or 
to adjust your height and then touch “SET” to confirm.
e)The age value will flash. Touch 
or 
to select your age and touch “SET” to confirm. The display will then register 0.0. Allow the scale to turn off.
Note: If there is no operation after five seconds and you have not completed the set-up the scale will turn to 0.0 and the process must be started again by following procedure a).
Loading...