Many thanks for your selection of our products. Before use, please thoroughly read this
manual to ensure you can enjoy every function of this machine and keep it long under
normal service. Please also keep this manual properly for future reference during use.
Copyright
Without prior written permission by the Company, the contents in this publication shall not be
reproduced, distributed or reprinted in electronic, mechanical, magnetic, optical, chemical,
manual or any other form, nor can they be stored into any search system or translated into
any language or computer language. Brand name and product name are the trademarks or
registered trademarks of respective company.
Statement
We reserve the final right to interpret relevant contents in this manual. The contents in this
manual are subject to change without prior notice. We do not provide any warranty to the
information herein contained or assume any liability for any possible errors in this document.
This manual is provided to the users for reference only during use. Our products are under
continuous improvement and upgrading. We appreciate and thank you for your opinions and
suggestions on a better product.
8 Security and disposal advise ...........................................................................................33
28
English
28
29
29
3
English
1 Introduction
The video camera you select and purchase is a digital video device integrating high-quality
digital video camera, digital camera, super MP3, digital pen recorder and PC-Cam. It will
22 Cradle Connector
23 DC Input Port
24 USB Port
25 Audio/Video Output Port
Note:
The bundled AC Adaptor output voltage is 5V, 1.0A. Please only use the bundled AC Adaptor.
6
2 Get Video Camera Ready
2.1 How to Turn ON/OFF the Power of Video Camera
2.1.1 Installing Battery
video camera uses rechargeable lithium ion battery.
This
refer to following procedures for correct
Please
tallation of the battery:
ins
1) Move the battery lock along direction to open the
ca
rd/battery cover.
2) Install the battery into the battery cell as directed and
ensure the
inserted. Before installation, confirm the polarity is correct.
3) Slide
2.1.2 Turning ON/OFF Video Camera
1) Turning ON: Press down the power button for 1~2 seconds and release it to start up the
sys
2) Turning OFF: Press down the power button for 1 second or longer to turn off the system
normally
Note:
From LCD display, you can see the battery status as shown below:
battery lock is fastened after the battery is
and close the card/battery cover.
tem. If the system is not started normally, please check the battery power and polarity.
.
Battery power is full and you can use the video camera normally.
Battery power is sufficient and you can use the video camera normally.
Battery power is half consumed. Please prepare for charging.
Battery is low power. Please charge it.
Battery power is completely consumed. The video camera will be turned off
au
tomatically.
English
2.1.3 Charging Battery
1) Place the battery contained video camera onto the USB cradle.
2) Connect the DC input line to (DC IN 5.0V) port on the USB cradle.
3) Connect the power line to the charging adaptor and power socket. The charging
indicator will become red and the charging is started.
4) Wait until the charging indicator turns into green, indicating that the battery is fully
Usually, this process will take 3 hours around.
charged.
Note:
The bundled battery is 850 mAh, 3.7V. Please only use the bundled battery.
7
English
Note:
This camera also supports USB charging.
1) Insert the video camera into the base
2) Use the bundled USB cable to connect between the base and computer. Switch on the
ter.
compu
3) The charging indicator will become red when it starts charging.
4) Wait until the charging indicator turns into green, indicating that the battery is fully
.
charged
2.1.4 Removing Battery
1) Move the battery lock along direction to open
the card/battery cover.
2) Push the battery lock and incline the video
mera to remove the battery.
ca
3) Slide and close the card/battery cover.
8
2.2 Installing and Removing SD Card
It is suggested to use SD card if you need an external memory card to expand the storage
capacity of your video camera.
Installing SD Card
1) Turn the video camera off and open the
card/battery cover.
2) Insert the memory card into the slot as
shown below, until you hear a click.
3) Slide and close the card/battery cover.
Removing SD Card
1) Turn the video camera off.
2) Slide and open the card/battery cover. Press the SD card inward.
The card will eject out.
3) Pull out the card and close the card/battery cover.
Note:
To use a new SD card, you have to format it firstly.
English
9
English
2.3 Using LCD Display
When recording the images, you can view the pictures from LCD display. From this display,
you can also view the contents recorded before.
1) Open the LCD display.
2) Adjust the angle of LCD display according to the recording/play angle required. To its
maximum, the display can be rotated to following angle: 90 in open/close, 180 in forward
direction and 90 in reverse direction.
3) When in video and shot preview, you can press RIGHT direction button to overturn the
images on the display. Then you can align the lens toward yourself for self shot. To return to
normal status, just press RIGHT direction button again.
2.4 Selecting Operation Mode
1) Set to
2) Press down (MODE) button to select the operation mode.
Each press of (MODE) button will change the operation mode sequentially as below.
(Video) B (Shooting) B (Voice) B (Video)
(Movie) B (Photo) B (Voice) B (Recording) B (MP3 Browser) B (Movie)
to select the shoot mode. Set to to select the playback mode.
Shoot mode
Playback Mode
2.4.1 Definition of Display Icons
Video Capture
1) Video Capture Status
2) Recorded/Recordable Time
3) Battery Power Indication
4) Movie Size
5) Memory Card
6) Digital Zoom
7) Microspur Status
8) White Balance Mode
9) Video Voice
10
Loading...
+ 23 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.