Dynojet Tire Temperature Sensor User Manual

©1998-2001 Dynojet Research, Inc. All Rights Reserved. Tire Temperature Sensor Installation Guide This manual is copyrighted by Dynojet Research, Inc., hereafter referred to as Dynojet,
and all rights are reserved. This manual, as well as the software described in it, is furnished under license and may only be used or copied in accordance with the terms of such license. This manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Dynojet. Dynojet assumes no responsibility or liability for any error or inaccuracies that may appear in this manual. Except as permitted by such license, no part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Dynojet.
The Dynojet logo is a trademark of Dynojet Research, Inc. Any trademarks, trade names, service marks, or service names owned or registered by any
other company and used in this guide are the property of their respective companies. Dynojet Research, Inc., 2191 Mendenhall Drive, North Las Vegas, Nevada 89081, USA. Printed in USA. Part Number: 98295100 Version 02 (04/2001)
T
ABLE OF
C
ONTENTS
Tire Temperature Sensor Installation
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembling the Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Wiring the Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Securing the Mounting Bracket and Sensor Assembly . . . . . . . . . . . . . . . . . . . 5
Tire Temperature Sensor Installation Guide
i
T
IRE
T
EMPERATURE
S
ENSOR INSTALLATION
This document provides instructions for installing the tire temperature sensor. To ensure safety and accuracy in the procedures, perform the procedures as they are described.
Document Part Number: 98295100 Version 02 Last Updated: 04-06-01
Tire Temperature Sensor Installation Guide
1
TIRE TEMPERATURE SENSOR

Introduction

INTRODUCTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The tire temperature sensor allows you to monitor the temperature of the motorcycle tire.

TECHNICAL SUPPORT

For assistance, please contact Dynojet Technical Support at 1-800-992-3525, or write to Dynojet Research at 2191 Mendenhall Drive, North Las Vegas, NV 89081.
Visit us on the World Wide Web at www.dynojet.com where Dynojet provides state of the art technical support, on-line shopping, 3D visualizations, and press releases about our latest product line.

PARTS

The following table shows all of the parts included in the Tire Temperature Sensor Installation kit. Check your kit against the parts listed to make sure you have received all of the parts. If any part is missing, contact Dynojet Technical Support.
part number description quantity
21696202 Mounting Bracket 1 35130220 Magnetic Base 1 21696201 Sensor Bracket 1 21696203 Sensor Bracket Peg 1 49950030 Sensor, Sensor Cable 1 36340422 Screw, 10-32 1
magnetic base
sensor bracket
sensor bracket
peg
mounting
bracket
2
Tire Temperature Sensor Installation Guide
sensor cable
sensor
10-32 screw
Figure 1: Temperature Sensor Parts
INSTALLATION GUIDE

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This section contains instructions for installing the tire temperature sensor.

ASSEMBLING THE SENSOR

1 Mount the sensor bracket to the sensor bracket peg using the 10-32 screw.
10-32 screw
sensor bracket
sensor bracket peg
Installation
2 Mount the sensor to the sensor bracket.
3 Mount the sensor bracket to the magnetic base.
sensor
nut
sensor bracket
magnetic base
Figure 2: Mount the Sensor Bracket
2a Remove one of the nuts from the sensor. 2b Slip the sensor bracket on the sensor. 2c Secure the sensor bracket to the sensor using the nut.
Figure 3: Mount the Sensor to the Bracket and Magnetic Base
Version 2 Tire Temperature Sensor Installation Guide
3
TIRE TEMPERATURE SENSOR
Installation

WIRING THE SENSOR

1 Remove the hood from the dyno. 2 Attach the five wires on the cable coming from the tire temperature sensor to
TEMP on the Breakout board as described below.
• Green wire to G2
•White wire to W2
•Black wire to B2
• Red wire to R2
• Silver (ground) wire to S2 Note: Do not use G1 through S1. These are reserved for monitoring the brake
temperature.
sensor cables
TEMP
Figure 4: Wiring the Sensor
4
Tire Temperature Sensor Installation Guide

SECURING THE MOUNTING BRACKET AND SENSOR ASSEMBLY

1 Replace the hood on the dyno. 2 Secure the mounting bracket to the hood using the bolts removed earlier. 3 Secure the magnetic base to the mounting bracket. 4 Adjust the sensor so it is pointing at the center of the tire.
magnetic base
mounting
bracket
INSTALLATION GUIDE
Installation
tire
sensor
bolt
dyno hood
Figure 5: Secure the Magnetic Base and Adjust the Sensor
Version 2 Tire Temperature Sensor Installation Guide
5
Loading...