Dynexproducts DX-TRPMN57 Quick Setup Guide
Converting to a monopod
1 Holding the tripod rmly, unscrew the monopod leg from the
main tripod assembly.
Monopod leg
2 Unscrew the center column locking screws, unscrew the bottom
hanging hook, then remove the center column from the tripod
base.
Storing your tripod
1 Remove your camera.
2 Loosen the center column locks. Raise the column as far as it
will go, then tighten the bottom lock. Lower the top section as
far as it will go.
3 Twist each leg lock counterclockwise and collapse the legs.
4 Wrap your hand around all four leg locks, then twist clockwise
to tighten them all at once.
5 Pull out the leg release tabs and ip the legs up.
Note: You may need to rotate the head slightly so the legs t between
the knobs.
6 Store the tripod into the carrying case.
Important safety instructions
• Make sure that all leg locks are correctly tightened and that the
legs are fully opened before use.
• Do not carry or transport your tripod with camera equipment
attached (for example, over your shoulder or cradled in your
arms).
• Do not expose your tripod to excessive heat or cold, or use near
any ame or re.
• Do not oil or grease any part of the tripod.
• Do not use any solvents or thinners to clean your tripod. Use
only a mild detergent and wipe dry with a soft, lint-free cloth.
• Do not exceed the load limit of this tripod.
DX-TRPMN57
57" Compact
Tripod-Monopod Combo
Center column
Hanging hook
3 Screw the center column (with ball head) into the monopod leg.
Specications
• Maximum operating height: 57.1 in. (145 cm)
• Minimum operating height: 6.7 in. (17 cm)
• Folded height (reversed legs): 13.4 in. (34 cm)
• Net weight: 2.7 lbs (1.24 kg)
• Max operating load: 8.8 lb (4 kg)
• Number of leg sections: 5
• Quick release thread: 1/4 in. (0.6 cm)
• Panoramic angle: horizontal: 360° and vertical: 90°
• Material: aluminum alloy
One-year limited warranty
Visit www.dynexproducts.com for details.
Contact Dynex:
For customer service, call 800-305-2204 (U.S. and Canada) or
01-800-926-3020 (Mexico)
www.dynexproducts.com
DYNEX is a registered trademark of BBY Solutions, Inc.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 BBY Solutions, Inc. All Rights Reserved.
4 To adjust the height, unscrew the leg twist locks, extend the leg
to the height you want, then tighten the leg locks.
V1 ENGLISH 14-0371
Before using your new product, please read
these instructions to prevent any damage.
QUICK SETUP GUIDE
Package contents
• Tripod
• Carrying case
• Quick Setup Guide
Features
• Compact portable size, with built in bubble level, can support a
camera up to 8.8 Ibs (4 kg)
• One leg conversion to use as a monopod
• Super-low 6.7 in. (17 cm) shooting angle
• Reversed folding reduces storage space requirement to 13.4 in.
(34 cm)
Reversed
folding
One leg monopod
conversion
# Item
1 Quick-release
mounting plate
2 Mounting base
plate
3 Variable angle
ball head
4 Pan locking knob
5 Quick-release
mounting plate
locking knob
6 Ball head locking
knob
7 Center column
locks
8 Angle adjusting
tab
9 Center column
10 Grip sponge
11 Hanging hook
12 Twist screw leg
lock
13 Rubber feet
Description
Mount your device to this removable plate.
Holds the quick-release mounting plate.
Allows the camera to be adjusted to any angle.
Locks the horizontal movement of the ball head.
Locks the quick-release mounting base plate to
the tripod.
Lets you adjust the angle of the ball head.
Lock the rst and second sections of the column.
Lets you adjust the leg angle position.
Adjustable column provides a quick height
adjustment.
Grip the tripod comfortably.
Hang a heavy item on this hook to add stability to
the tripod.
Locks the legs in place.
Provide a secure, non-slip footing for your tripod.
Setting up your tripod
1 Swing each leg down.
2 With one hand, grab all the leg locks on one leg and twist them
counterclockwise to loosen them.
3 Extend the leg sections to the height you want.
4 Twist each leg lock clockwise to tighten it. Repeat for each leg.
Caution: Incorrectly securing a leg lock can cause the tripod leg to
retract unexpectedly and could result in damage to the tripod or to the
attached camera or camcorder.
5 To set the angle position, pull out the angle adjusting tab and
lift the tripod leg, then press the angle adjusting tab in place.
6 Adjust the center column by unscrewing the center column
locks and raising the center column to the height you want,
then tighten the center column locks.
7 To remove the quick-release mounting plate, unscrew the
quick-release mounting plate locking knob, then lift the plate
away from the head.
8 Align the bottom of your camera or camcorder with the 1/4"
mounting screw, then secure your camera or camcorder to the
plate with the screw. The screw should be tight.
9 Slide the plate onto the tripod head. Turn the quick-release
mounting plate locking knob until it stops to secure the plate.
Using your tripod
1 To adjust the horizontal movement of the ball head, turn the
pan locking knob counter-clockwise, move the ball head into the
position you want, then lock the ball head in place by turning the
knob clockwise until tight.
2 To adjust the head ball, turn the ball head locking knob counter-
clockwise, adjust the ball head, then lock the ball head in place
by turning the knob clockwise until tight.
3 For low angle shooting, unscrew the hanging hook, then remove
the center column. Reverse the direction of the center column,
then insert the column into the base. Screw the hanging hook
into place.
Hanging hook
Loading...