Manufacturers, retailers and the rest of the consumer electronics industry are committed
to making home entertainment safe and enjoyable.
•
As you enjoy your television, please note that all televisions - new and old- must be
supported on proper stands or installed according to the manufacturer's
recommendations. Televisions that are inappropriately situated on dressers, bookcases,
shelves, desks, speakers, chests, carts, etc., may fall over, resulting in injury.
TUNE IN TO SAFETY
•
ALWAYS follow the manufacturer’s recommendations for the safe installation of your
television.
•
ALWAYS read and follow all instructions for proper use of your television.
•
NEVER allow children to climb on or play on the television or the furniture on which the
television is placed.
•
NEVER place the television on furniture that can easily be used as steps, such as a chest
of drawers.
•
ALWAYS install the television where it cannot be pushed, pulled over or knocked down.
•
ALWAYS route cords and cables connected to the television so that they cannot be
tripped over, pulled or grabbed.
WALL OR CEILING MOUNT YOUR TELEVISION
1
•
ALWAYS contact your retailer about professional installation if you have any doubts
about your ability to safely mount your television.
•
ALWAYS use a mount that has been recommended by the television manufacturer and
has a safety certification by an independent laboratory (such as UL, CSA, ETL).
•
ALWAYS follow all instructions supplied by the television and mount manufacturers.
•
ALWAYS make sure that the wall or ceiling where you are mounting the television is
appropriate. Some mounts are not designed to be mounted to walls and ceilings with
steel studs or cinder block construction. If you are unsure, contact a professional installer.
•
Televisions can be heavy. A minimum of two people is required for a wall or ceiling
mount installation.
MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR
HOME
•
Many new television buyers move their older CRT televisions into a secondary room after
the purchase of a flat-panel television. Special care should be made in the placement of
older CRT televisions.
•
ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its
size and weight.
•
NEVER place your older CRT television on a dresser where children may be tempted to
use the drawers to climb.
•
ALWAYS make sure your older CRT television does not hang over the edge of your
furniture.
CE.org/safety
2
DX-24E310NA15
Important Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates that
dangerous voltage
constituting a risk of electric
shock is present within your TV.
This label is located on the
back of your TV.
This symbol indicates that
there are important operating
and maintenance instructions
in the literature accompanying
your TV.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the AC power adapter from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the
cart/apparatus combination to avoid injury from
tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15 The wall plug is the disconnecting device. The plug
must remain readily operable.
16 Remote control batteries should not be exposed to
excessive heat such as sunshine, fire, or the like.
17 The apparatus should not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, should be placed on the apparatus.
War ning
Electric shock hazard
To reduce the risk of fire or electric shock, do not remove
any cover or expose the device to rain or moisture. No
user-serviceable parts are inside. Refer servicing to
qualified service technicians.
Lightning
For added protection for your device receiver during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
power outlet and disconnect any antenna or cable
system. This helps prevent property damage and
personal injury from lightning and power line surges.
Power lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching
such power lines or circuits as contact with them might
be fatal.
Handling the LCD panel
•Your TV’s screen is made of glass. Do not drop your TV or
hit, jolt, or press hard against the LCD panel. If the screen
breaks, be careful of broken glass.
•If the LCD panel is broken, make absolutely sure that you
do not touch the liquid in the panel. This may cause skin
inflammation.
•If the liquid gets in your mouth, immediately gargle, rinse,
and consult with your doctor. Also, if the liquid gets in
your eyes or touches your skin, consult with your doctor
after rinsing for at least 15 minutes or longer in clean
water.
Replacement parts
When replacement parts are required, make sure that
the service technician uses replacement parts specified
by the manufacturer that have the same characteristics
as the original part. Unauthorized substitutions may
result in fire, electric shock, personal injury, or other
hazards.
Safety check
After completing any service or repair to this device, ask
the service technician to perform routine safety checks
to determine that your TV is in correct operating
condition.
www.dynexproducts.com
DX-24E310NA15
3
Power source
Operate your TV only from the type of power source
indicated on the marking label. If you are not sure of the
type of power supplied to your home, consult an
electrician or your local power company.
Servicing
These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that
contained in the operating instructions unless you are
qualified to do so.
Caution
Damage requiring service
Unplug this TV from the power outlet and refer
servicing to qualified service personnel under the
following conditions:
• When the power supply cord or plug is damaged or
frayed.
• If liquid has been spilled or objects have fallen into
your TV.
• If your TV has been exposed to rain or water.
• If your TV does not operate normally by following the
operating instructions. Adjust only those controls that
are covered by the operating instructions because
incorrect adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore your TV to its normal
operation.
• If your TV has been dropped or damaged in any way.
• When your TV exhibits a distinct change in
performance.
Outdoor antenna grounding
If an outside antenna or cable system is connected to
your TV, make sure that the antenna or cable system is
grounded to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides
information with respect to correct grounding of the
mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of the antenna-discharge unit,
connection to grounding electrodes, and requirements
for the grounding electrode.
Antenna lead-in wire
1
Grounding clamp
2
Antenna discharge
3
unit
Grounding
4
conductors
Ground clamps
5
Power service
grounding electrod e
6
system
Electric service
7
equipment
Note to CATV system installer
Article 820 of the National Electrical Code, ANSI/NFPA
No. 40 provides guidance for correct grounding.
Specifically, it states that the cable ground must be
connected to the grounding system of the building as
close to the point of cable entry as practical.
Condensation
Moisture will form on the TV if the TV is brought from
cool surroundings into a warm room or if the
temperature of the room rises suddenly. When this
happens, the TV's performance may be impaired. To
prevent this, let the TV stand in its new surroundings for
about an hour before switching it on, or make sure that
the room temperature rises gradually.
Condensation may also form during the summer if the
TV is exposed to the breeze from an air conditioner. In
such cases, change the location of the TV.
Mobile telephone warning
To avoid interference with your TV picture and sound,
operating problems, or even damage, keep your
cordless and cellular telephones away from the TV.
End of life directives
Your TV may contain materials that are regulated for
environmental reasons. Your TV also contains materials
that can be recycled and reused. To help protect the
environment, contact your local authorities for
information about disposal or recycling and about
finding a recycler in your area before you dispose of
your TV.
Non-active pixels
The LCD panel contains almost 3 million thin film
transistors, which provide exceptionally sharp video
quality. Occasionally, a few non-active pixels may
appear on the screen as a fixed blue, green, or red point.
These non-active pixels do not adversely affect the
performance of your TV, and are not considered defects.
www.dynexproducts.com
4
Dynex 24" LED TV
Introduction
Congratulations on your purchase of a high-quality Dynex product. Your DX-24E310NA15 represents the state of the art in
LED TV design and is designed for reliable and trouble-free performance.
Installing the stand or wall mount bracket
Notes
• If you plan to wall-mount your TV, do not install the stand.
• Store the stand and stand screws in case you decide to use the
stand in the future.
Installing the stand
1 Carefully place your TV face-down on a cushioned, clean surface to protect the screen from damages and scratches.
Dynex 24" LED TVDX-24E310NA15
www.dynexproducts.com
Dynex 24" LED TV
2 Find the front of the stand.
DX-24E310NA15
5
Front
3 Secure the TV stand to the stand column with the three provided M4 (12 mm) screws.
Screw typeScrew length# of screws
M412 mm3
www.dynexproducts.com
6
Installing the wall-mount bracket
Warning
This TV is intended to be supported by a UL Listed wall mount
bracket with suitable weight/load. (See “Miscellaneous” on
page 57.)
1 Carefully place your TV face-down on a soft surface to protect the screen from damages and scratches.
Dynex 24" LED TVDX-24E310NA15
2 If the TV stand is installed, remove the three screws that secure the stand column to your TV, then remove the stand.
www.dynexproducts.com
Dynex 24" LED TV
3 Attach the wall-mount bracket to your TV using either the four provided M4 × 8 mm or the M4 x 28 mm screws that came
with the TV. See the instructions that came with the wall-mount bracket for information about how to correctly hang
your TV.
Caution
Do NOT use the screws that came with the wall mount because
they may be too long.
If your wall mount uses spacers, use the provided M4 x 28 mm
screws. If your wall mount does not use spacers, use the provided
M4 x 8 mm screws.
Notes
• The length of the wall-mount screws vary depending on the
wall-mount bracket you purchased. See the instructions that
came with the wall-mount bracket for screw lengths.
• The mounting holes on the back of your TV take type M4
screws.
2.95 in. (75 mm)
DX-24E310NA15
7
2.95 in. (75 mm)
www.dynexproducts.com
8
Dynex 24" LED TVDX-24E310NA15
TV components
Package contents
• Remote control and batteries (2 AAA)
• TV stand and screws (3)
• M4 screws (8 mm length) (4 pcs.) wall-mount screws
• M4 screws (28 mm length) (4 pcs.) wall-mount screws
• AC power adapter
• QUICK SETUP GUIDE
•IMPORTANT INFORMATION
Front
#ItemDescription
The power indicator:
• Turns off when your TV is on.
Power indicator
1
Remote control
sensor
2(power)
3 (input)
4 (menu)
5
6
and
(channel
buttons)
– and +
(volume
buttons
• Lights red when your TV is off
(standby mode).
The remote control sensor receives
signals from the remote control. Do
not block.
Press to turn your TV on or off
(standby mode).
War ning: When your TV is off,
power still flows through it. To
completely disconnect power,
unplug the power adapter.
Press one or more times to select
the video input source you want,
then wait a few seconds. Your TV
switches to the source you
selected. For more information, see
“Selecting the video input source”
on page 31.
In menu mode, press to confirm
selections.
Press to open the on-screen menu.
For more information, see “Using
the on-screen menus” on page 32.
Press to go to the next or previous
channel in the channel list. For
more information, see “Selecting a
channel” on page 33.
Press to increase or decrease the
volume.
www.dynexproducts.com
Dynex 24" LED TV
DX-24E310NA15
9
Side jacks
#ItemDescription
1DC IN (12V)
2USB
3HDMI2
4HDMI 1 (DVI)
VIDEO
5
L and R audio
DIGITAL
6
OUTPUT
(COAXIAL)
7SERVICE PORT
Plug the AC power adapter into this
connector.
Connect a USB flash drive to this
jack to view compatible JPEG
picture files. For more information,
see “Connecting a USB flash drive”
on page 23 and “Using a USB flash
drive” on page 34.
Connect an HDMI device to this
jack. For more information, see
“HDMI (best)” on page 12, 17, 19,
or 21.
Connect an HDMI device to this
jack. For more information, see
“HDMI (best)” on page 12, 17, 19,
or 21.
OR
Connect the video for a DVI device
to this jack. For more information,
see “DVI (same as HDMI but
requires an audio connection)” on
page 13 or 22.
Connect the video for an AV
(composite video) device to the
VIDEO jack.
Connect the audio for an AV
(composite video) to the L and R
audio jacks.
For more information, see “AV
(composite video) (good)” on
page 14, 18, or 20.
Connect a digital audio amplifier or
home theater system to this jack to
listen to TV audio through the
amplifier speakers. For more
information, see “Digital audio” on
page 25
For service use only. Do not
connect a device to this jack.
#ItemDescription
Connect an antenna or cable TV to
this jack. For more information
about connecting a cable box
8ANT/CABLE IN
9AUDIO OUT/
.
using coaxial, see “Coaxial (good)”
on page 15.” For information about
connecting an antenna or direct
cable, see “Connecting an antenna
or cable TV (no box)” on page 16.
Connect headphones, an analog
audio amplifier, a home theater
system, or a sound bar to this jack.
For more information, see “Analog
audio” on page 26.
www.dynexproducts.com
10
Dynex 24" LED TVDX-24E310NA15
Remote control
#ButtonDescription
CCD
7
ASPECT
8
MENUPress to open the on-screen menu.
9
ENTERPress to confirm selections or chan ges.
10
/MUTE
11
Numbers
12
13
14
15
16
/RECALLPress to go to the last viewed channel.
SLEEP
MTS/SAP
INFO*
Press to turn closed captioning on or off. You can
select CC On, CC Off, or CC On When Mute. See
“Turning closed captioning on or off” on page 46.
Press to change how the picture looks on the screen
(aspect ratio). Se e the Aspect Ratio option in
“Adjusting the TV picture” on page 37.
Press to mute the sound. Press again to restore the
sound.
Press to enter channel numbers and the parental
control password.
Press to set the sleep timer. See “Setting the sleep
timer” on page 45.
In analog TV mode, press to select Stereo, Mono, or SAP.
In digital TV mode, press to select an alternate audio
language, if available. See “Adjusting sound settings”
39
on page
Press to display TV status information, such as the
channel number, channel name (if available), or
signal source. See “Viewing channel information” on
page 33.
.
#ButtonDescription
(power)
1
2
PICTURE
3
AUDIO
4
INPUT
5
Press to turn your TV on or off (Standby mode).
Warn ing: When your TV is off, power still flows into
it. To disconnect power, unplug the power adapter.
Press to enter a digital sub-channel number. See
“Selecting a channel” on page 33.
Press to select the picture mode. You can select Vivid, Standard, Energy Savings, or Custom. See
“Adjusting the TV picture” on page 37.
Press to select an audio mode. You can select
Standard, Music, Movies, News, or Custom. See
“Adjusting sound settings” on page39.
Press to open the INPUT SOURCE list, then press or
to select a video input source. See “Selecting the
video input source” on page 31.
CH+ / CH–
17
HOMEPress to open the on-screen menu.
18
FAV
19
EXITPress to close the on-screen menu.
20
21
Press to go to the next or previous channel in the
channel list. See “Selec ting a channel” on page 33.
Press to open the Favorite s channel list. See “Setting
up a favorite channel list” on page 50 and “View ing a
favorite channel” on page 51.
Press to navigate through the on-screen menus and
adjust setti ngs.
VOL+/VOL–Press to increase or decrease the volume.
6
www.dynexproducts.com
Dynex 24" LED TV
DX-24E310NA15
11
What connection should I use?
Your TV has several connection types for connecting
devices to your TV.
For the best video quality, you should connect a device
to the best available connection.
Use the following tables to identify cables:
Video
quality
Best (use this
if your devices
have HDMI)
Better than
coaxial
Connection
type and jack
HDMI
video/audio
Composite video
(requires an
audio
connection)
Cable connector
Connection
type and
jack
Coaxial digital
audio output
Analog audio
input
3.5mm analog
audio output
Cable connectors
Good
Coaxial
video/audio
You can use the HDMI 1 (DVI) jack on your TV to connect
a DVI device to your TV. For more information, see “DVI
(same as HDMI but requires an audio connection)” on
page 13 or page 22.
Cautions
• Check the jacks for position and type
before making any connections.
• Loose connections can result in image
or color problems. Make sure that all
connections are tight and secure.
• The external audio/video equipment
shown may be different from your
equipment. If you have questions,
refer to the documentation that came
with your equipment.
• Always unplug the power adapter
when connecting external equipment.
www.dynexproducts.com
12
Connecting a cable or satellite box
Many cable or satellite TV boxes have more than one connection type. To get the best video, you should use the best
connection type available. For more information, see “What connection should I use?” on page 11.
HDMI (best)
On your TV
HDMI cable
connector
Cable or
satellite box
HDMI jack
Dynex 24" LED TVDX-24E310NA15
HDMI cable
Side of TV
1 Make sure that your TV’s power adapter is unplugged and all connected equipment is turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect an HDMI cable (not provided) to one of the HDMI jacks on the side of your TV and to the HDMI OUT jack on the
cable or satellite box.
4 Plug your TV’s power adapter into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 Press INPUT to open the INPUT SOURCE list.
6 Press
or to highlight HDMI1 or HDMI2, then press ENTER.
Note
An HDMI cable carries both audio and video. You do not need to
use any audio cables.
www.dynexproducts.com
Dynex 24" LED TV
DVI (same as HDMI but requires an audio connection)
Notes
• Your TV supports DVI video only.
• You must use the HDMI 1 (DVI) jack to connect a cable box
using DVI.
• To add sound for a DVI connection, connect external speakers
or a sound bar to the cable or satellite box.
DX-24E310NA15
13
On your TV
HDMI cable
connector
HDMI 1 (DVI)
jack
1 Make sure that your TV’s AC power adapter is unplugged and all connected equipment is turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect an HDMI-DVI adapter (not provided) to one end of an HDMI cable (not provided), then connect the adapter to
the DVI OUT jack on the cable or satellite box.
4 Connect the other end of the cable to the HDMI 1 (DVI) jack on the side of your TV.
5 Plug your TV’s AC power adapter into a power outlet, turn on your TV, then turn on the cable or satellite box.
6 Press INPUT to open the INPUT SOURCE list.
7 Press
or to highlight HDMI1, then press ENTER.
Cable or
satellite box
HDMI cable with
HDMI-DVI adapter
Side of TV
www.dynexproducts.com
14
AV (composite video) (good)
On your TV
Dynex 24" LED TVDX-24E310NA15
Note
Cables are often color-coded to match color-coded jacks.
Cable or
satellite box
(composite video cable)
AV
(composite
video)
cable
connector
AV
(composite
video) jack
1 Make sure that your TV’s power adapter is unplugged and all connected equipment is turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect an AV cable (not provided) to the VIDEO jack and L and R audio jacks on the side of your TV and to the
composite video and audio out jacks on the cable or satellite box.
Audio cable
connectors
Side of TV
Analog
audio jacks
Note
When you connect the audio using the L and R audio jacks, the
audio output is analog.
AV cable
4 Plug your TV’s power adapter into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 Press INPUT to open the INPUT SOURCE list.
6 Press
or to highlight AV, then press ENTER.
www.dynexproducts.com
Dynex 24" LED TV
Coaxial (good)
On your TV
Coaxial cable
DX-24E310NA15
15
Coaxial cable
connector
ANT/CABLE IN
jack
1 Make sure that your TV’s power adapter is unplugged and all connected equipment is turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect a coaxial cable (not provided) to the ANT/CABLE IN jack on the side of your TV and to the antenna or cable TV
wall jack.
4 Plug your TV’s power adapter into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 Press INPUT to open the INPUT SOURCE list.
6 Press
7 If you cannot tune to channels you know exist, scan for channels. See “Automatically scanning for channels” on page 49.
or to highlight TV, then press ENTER.
Cable or
satellite box
Side of TV
Notes
• Use a coaxial cable to eliminate interference and noise from
radio waves.
• Do not bundle the coaxial cable with the power adapter or
other cables.
www.dynexproducts.com
16
Connecting an antenna or cable TV (no box)
Dynex 24" LED TVDX-24E310NA15
On your TV
Coaxial cable
connector
ANT/CABLE IN
jack
1 Make sure that your TV’s power adapter is unplugged and all connected equipment is turned off.
2 Connect a coaxial cable (not provided) to the ANT/CABLE IN jack on the side of your TV and to the antenna or cable TV
wall jack.
3 Plug your TV’s power adapter into a power outlet, then turn on your TV.
4 Press INPUT to open the INPUT SOURCE list.
5 Press
6 If you cannot tune to channels you know exist, scan for channels. See “Automatically scanning for channels” on page 49.
or to highlight TV, then press ENTER.
Antenna or
cable TV
(no box)
Coaxial cable
Side of TV
Notes
• Use a coaxial cable to eliminate interference and noise from
radio waves.
• Do not bundle the coaxial cable with the power adapter or
other cables.
• If the antenna is not installed correctly, contact qualified service
personnel to correct the problem.
• If the signal level for a channel is weak, the picture may be
distorted. Adjust the antenna or use a highly directional
outdoor or set-top antenna with a built-in amplifier.
• If the picture quality is good on some channels and poor on
others, the problem may be caused by a poor or weak signal
from the broadcaster or cable TV provider.
• If you connect to cable or satellite TV without a set-top box and
experience poor picture quality, you may need to install a
set-top box to improve signal reception and picture quality.
Contact your cable or satellite TV provider about upgrading to
a set-top box.
• Many high-definition (HD) channels upscale
standard-definition (SD) content. The picture displayed on your
TV is still displayed as SD, thus the picture quality will not be as
clear or crisp as it would be if the content was originally
recorded in HD.
www.dynexproducts.com
Loading...
+ 44 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.