CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
LASER KLASSE 1
LUOKAN 1 LASERLAITE
PRODUIT LASER
CATEGORIE 1
DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM
VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT
DEM STRAHL AUSSETSEN
ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE.
EVITER TOUTE EXPOSITION AUX RAYONS.
Copyright Statement
It is a criminal offence, under applicable copyright laws, to make unauthorised
copies of copyright-protected material, including computer programs, films,
broadcasts and sound recordings. This equipment should not be used for such
purposes.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that
may cause undesired operation.
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can emit radio frequency energy
and, if not installed or used in accordance with the instructions, may cause
interference to radio communications. However, television reception interference
can be determined by turning the equipment off and on. The user is encouraged to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet different from that to which the receiver
is connected
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FOR EUROPE
“The drive is in conformity with the EMC directive and low-voltage
directive.”
Table of Contents
INTRODUCTION 1
SYSTEM REQUIREMENTS 2
PACKAGE CONTENTS 2
INSTALLATION 3
HOST INTERFACE CONNECTIONS 3
HARDWARE INSTALLATION 4
DRIVER INSTALLATION 6
Windows Environment 6
SOFTWARE INSTALLATION 6
Windows Environment 6
CONNECTION & OPERATION 7
FRONT PANEL 7
REAR VIEW 8
TECHNICAL DATA 9
TROUBLESHOOTING 12
CD-WRITER 5232IM
INTRODUCTION
CD-WRITER 5232IM is a half-height CD-ReWritable drive of standard
IDE interface. It supports maximum 52X speed writing ability on CD-R
discs, 32X speed on CD-RW discs and 52X speed reading performance.
The drive backs up all writing modes and different CD formats and it
automatically recognizes the media placed in the drive, whether a CD, a
CD-R or a CD-RW. With the bundled CD-RW mastering software, CDWRITER 5232IM is an ideal model for creating customized audio and
data CDs, and for archiving or distributing big files to achieve data
interchange and backup.
Here are some important features of CD-WRITER 5232IM:
♦ 8X, 16X, 24X, 32X, 40X, 48X and 52X writing speed on CD-R
media
♦ 4X, 10X, 12X, 16X, 24X and 32X writing speed on CD-RW media
♦ Adopts Buffer Underrun Prevention technology (MTKSuperLink)
♦ Supports MultiRead function
♦ Supports writing modes of TAO, DAO, SAO and packet writing
♦ Large internal buffer: 2MB
♦ Advanced dust-sealed design
♦ Low power consumption
♦ Firmware upgrade possibility via Flash Memory
1
CD-WRITER 5232IM
System Requirements
For IBM compatible PCs, the system requirements recommended
are as follows:
♦ PC sufficient to run Windows 98/ME/2000/XP
♦ Pentium II 350MHz above with at least 64MB of memory
♦ Fast and sufficient hard disk space (minimum 200MB for
installation, 1GB or more is recommended.)
♦ IDE host interface supporting ATAPI MMC command
♦ Operating system: Microsoft Windows 98/ME/2000/XP
Package Contents
♦ CD-WRITER 5232IM
♦ Audio cable
♦ Application software disc
2