Dynabrade 10700, 10705 Instructions Manual
Models:
10700 – Non-Vacuum
10705 – Central Vacuum
48
49
50
Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools
(ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabrade’s
Warning/Safety Operating Instructions for more complete safety information.
WARNING
!
For Serial No. 8B1126 and Higher
Index Key
No. Part # Description
1 97010 Screw (9)
2 95886 Washer (9)
3 Sanding Pads
56234 Non-Vacuum
56235 Central Vacuum
4 95898 Screw
5 57334 Counter Balance
6 96276 Nut (4)
7 57333 Mounting Plate Assy.
8 57736 8" Vacuum Shroud
9 95886 Washer (4)
10 96425 Screw (4)
11 96273 O-Ring
12 57335 Bearing
13 96118 Screw (3)
14 57748 Gear
15 96150 Shim (As Required)
16 57360 Felt Wiper
17 96275 Washer (4)
18 96274 Screw (4)
19 57749 Pinion
20 96166 Set Screw
21 57332 Lock Ring
22 54673 Rotor Key
23 57331 Motor Shaft
24 56052 Bearing
25 57324 Front Bearing Plate
26 54705 Rotor/Blade Set
27 54631 Cylinder Assembly
(Incl. 95865 Pin)
28 95865 Line-Up Pin
29 54629 Rear Bearing Plate
30 01206 Bearing
31 95626 Retaining Ring
32 57328 Shroud
33 10706 Housing – 10700
10707 Housing – 10705
34 95523 O-Ring (2)
35 57382 Gasket
36 56671 Handle
37 96123 Screw (2)
38 57396 Valve Stem
39 01211 Split-Lock Washer (6)
40 01464 Seal (2)
41 01472 Tip Valve
42 01468 Conical Spring
43 56673 Gasket
44 96328 O-Ring
45 56672 Adapter
46 01024 O-Ring (2)
47 57343 Regulator Plug
48 54199 Muffler Seat
49 54195 Muffler (3)
50 54194 Muffler Cap
51 98597 Retaining Ring
52 57344 Throttle Lever
53 01017 Pin
54 96421 Flat Washer (2)
55 01788 Screw (2)
56 01494 Inlet Bushing
11
15
16
17
23
22
24
25
27
28
29
30
31
32
43 44
45
52
53
51
40
55
39
54
46 47
7
5
10
9
8
3
2
33
35
36 38
2
39
42
41
40
37
34
Disc Pad Change
Use a 3 mm hex
wrench to remove
97010 Screw (5)
and 95886 Washers
from mounting
plate.Remove old
pad and replace
with new pad.
Replace screws and
washers and tighten
with 3 mm hex
wrench.No need to
remove shroud.
A
2
A
2
A
3
A
3
A
2
A
3
O
1
A
2
A
3
G
1
A
3
O
1
G
1
12
14
18
20
26
4
3.38 N•m
T
7 N•m
T
23 N•m
T
3 N•m
T
2 N•m
T
7 N•m
T
34 N•m
T
34 N•m
T
9 N•m
T
1
6
19
21
56
1
13
Parts Page Reorder No. APD00•12
Effective November, 2000
Supercedes APD97•10
8" Gear Driven
Orbital Sander (900 RPM)
Air Motor and Machine Parts.
AUTOMOTIVE
T
A
Adhesive:
A
2
= Loctite #271
A
3
= Loctite #242
Torque: N•m x 8.85 = In. - lbs.
Key
O
G
Oil: O
1
= Air Lube
Grease: G
1
= Lubriplate
630 AA
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
2
(APD00•12)
Full One Year Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date
of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or
replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have
been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance.
Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Machine Pad Length Weight Height Air Flow Rate Sound Motor Motor Air Pressure
Description Inch (mm) Inch (mm) Pound (kg) Inch (mm) SCFM (LPM) Level HP (W) RPM PSIG (Bars)
10700 8" (203) 12" (305) 4.3 (1.95) 5" (127) 28 (793) 85.6 dBA .46 (343) 900 90 (6.2)
10705 8" (203) 12" (305) 4.3 (1.95) 5" (127) 28 (793) 93.0 dBA .46 (343) 900 90 (6.2)
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose I.D. Size 3/8" (10 mm)
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade®Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade Rotary Vane air tools must be used with a filter-regulator-lubricator to maintain all warranties.
Operating Instructions:
Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.
Follow safety procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/sanding pad on tool.
2. Connect power source to tool. Be careful not to depress throttle lever in the process.
3. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
4. To avoid the danger of contaminating the workpiece from the lubricating oils permeating the air or sanding dust, it is recommended that this machine be
hooked up to a central vacuum system or one of our unique vacuum systems that gather all such contaminants in a paper or cloth dust bag. This self
contained vacuum system is highly efficient and convenient to use since it does not need to be attached to a separate vacuum system and is as mobile
as the machine itself.
Maintenance Instructions:
Products offered by Dynabrade should not be converted or otherwise altered from original design without the expressed written
consent from Dynabrade, Inc.
1. All Dynabrade Rotary Vane air motors should be lubricated with two drops of Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) placed directly into the air
inlet with throttle lever depressed every four hours of use.
2. Gears on the 8” Gear Driven should be greased with Dynabrade 95541 Grease Gun and 95542 Grease (10 oz. 283.5g.). Apply grease to the grease
fitting in the mounting plate, one full plunge every 300 hours of use.
3. 57360 Felt Wiper should be replaced every 600 hours.
4. An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11405 Air Line
Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and positive-drip lubrication of
pneumatic components. Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports.
5. Frequent drainage of water traps in air lines is recommended.
6. Some silencers on air tools may clog with use. Clean and replace as required.
7. AMotor Tune-Up Kit (P/N 96195) is available which includes assorted parts to help maintain and repair motor.
• Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or
death. Follow safety procedures posted in workplace.
• Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute
• Tool RPM must never exceed abrasive/sanding pad RPM rating, regardless of tool capacity.
• Operate machine for 30 seconds before application to workpiece to determine if machine is working properly and safely before work begins.
• Always disconnect power supply before changing abrasive or making machine adjustments.
• Inspect abrasives and sanding pads for damage or defects prior to and during operation of tool.
• Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
• Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
Notice
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication
during the use of this tool.
Note: To order replacement parts specify the model and serial number of your machine.
Safety Instructions:
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Loading...