DX Engineering DXE-UT-808X Instructions manual

Coaxial Cable Stripping Tool

DXE-UT-808X

For RG-8/X coaxial cable

DXE-UT-808X-INS Rev 1e

Patent Pending

The DXE-UT-808X has been designed to properly prepare DXE-8X, RG-8/X coax cable (.242" OD)

for use with DXE-PL259 PL-259 Connectors and DXE-UG176S Reducers.

Properly cut the end of the coaxial cable with the DXE-CNL-911 Coax Cable Cutter to get a good flush cut. You want the coax to be round and not oval
when viewed from the end. If the cable is slightly oval, gently use pliers to round out the end of the coaxial cable. Place the prepared coaxial cable end
into the body of the UT-808X labeled "1st CUT". Firmly grip the coaxial cable and the UT-808X, turn the UT-808X in a clock wise direction while
applying steady and slightly firm pressure. The UT-808X will begin cutting. Keep turning the tool until it will not cut anymore, it will stop cutting at the
proper length. Remove the coaxial cable. Place the PL-259 shell and the DXE-UG176S RG-8/X Reducer on the cable, fold the braided shield back over
the reducer exposing the center conductor's insulation. Turn the UT-808X around for the second cut. Insert the coaxial cable into the tool and again, turn
the tool in a clock wise direction until the cutting is complete. Remove the coaxial cable. Clean any excess cable cuttings from the tool. You may want to
trim some of the braid on the coaxial cable slightly using the DXE-170M precision shear side cutters prior to installing in a DXE-PL259 connector. This
combination of DXE tools allows perfect and easy connector installation every time! The premium cutting blades supplied with the UT-808X will last a
long time. If replacements blades are needed, order DXE-UT-RB-HD (customer supplied 7/64" Allen Wrench required).

1 - Cut Coaxial Cable 2 - Insert in "1st Cut" side 3 - Turn clockwise for first cut 4 - Reducer in Place, Braid folded Back

5 - Insert in other side for 2nd cut, turn clockwise to cut 6 - Trim Braid 7 - Install PL-259 & Solder

1200 Southeast Ave. - Tallmadge, OH USA

Phone: [phone] ∙ Tech Support and International: [phone]

Fax: [phone] ∙ E-mail: [e-mail]

Technical Support

If you have questions about this product, or if you experience difficulties during the installation, contact DX Engineering at [phone]. You can also
e-mail us at:

[e-mail]

For best service, please take a few minutes to review this instruction sheet before you call.

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from date of shipment. DX
Engineering’s sole obligation under these warranties shall be to issue credit, repair or replace any item or part thereof which is proved to be other than as warranted; no
allowance shall be made for any labor charges of Buyer for replacement of parts, adjustment or repairs, or any other work, unless such charges are authorized in advance by
DX Engineering. If DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering shall, u pon prompt notice thereof, issue shipping
instructions for return to DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by Buyer
unless made in writing. The above warranties shall not extend to any products or parts thereof which have been subjected to any misuse or neglect, damaged by accident,
rendered defective by reason of improper installation, damaged from severe weather including floods, or abnormal environmental conditions such as prolonged exposure to
corrosives or power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any goods or parts thereof furnished by Buyer or

acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties do not extend to other equipment and parts manufactured by others except to the
extent of the original manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof. These warranties

provide exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES
ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND
FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT STRICTLY IN ACCORDANCE
WITH THE FOREGOING.

©DX Engineering 2016

DX Engineering®, DXE®, DX Engineering, Inc.®, Hot Rodz®, Maxi-Core®, DX Engineering THUNDERBOLT®, DX Engineering Yagi Mechanical®, EZ-BUILD®,
TELREX®, Gorilla Grip® Stainless Steel Boom Clamps, Butternut®, SkyHawk™, SkyLark™, SecureMount™, OMNI-TILT™, RF-PRO-1B®, AFHD-4® are trademarks
of PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and product names are the
trademarks of their respective owners.

Specifications subject to change without notice.