DX Engineering DXE-LPFV1-2-CASE Instructions manual

SOTABEAM
Filter Enclosure

DXE-LPFV1-2-CASE

The DX Engineering Low Pass Filter Enclosure is custom made for the SOTABEAM SBM-LOWPASSKIT(s) - Version 1.2 PCBs ONLY.
Installation of the Low Pass Filter and construction of the box is easy to accomplish. The enclosure has a soft grommet to protect the SMA
cable and two easily removable hole covers to allow band switching of the optional filter assembly.

DXE-LPFV1-2-CASE Parts List

1 - Gray Aluminum Case - Top
1 - Gray Aluminum Case - Bottom
4 - Phillips Head Cover Screws
4 - PCB Spacers
8 - Phillips Head Screws for PCB mounting
4 - Internal Tooth Lock Washers 1. Install four Spacers on to PCB corners 2. Install PCB assembly to enclosure bottom with four Phillips Head
Screws
4 - Stick-on Rubber Feet
1 - Label

SOTABEAM PCB
installed in enclosure
bottom 3. Install SMA Cable Grommet in enclosure top 4. Route SMA cable through grommet

5. Enclosure top installed with four Phillips head screws 6. Install two removable access plugs 7. On the bottom, install 4 rubber feet

8. Install label on the top between removable plugs. Note the position of the “BAND A-B-C”

The removable plugs allow the user easy access to make changes of the Filter Board band selection jumpers.

Two views showing the completed DXE-LPFV1-2-CASE

With an optional SBM-LOWPASSKIT installed

Technical Support

If you have questions about this product, or if you experience difficulties during the installation, contact DX Engineering at [phone]. You can also e-mail us at:

[e-mail]

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from date of shipment. DX Engineering’s sole obligation under these warranties shall be to issue credit,
repair or replace any item or part thereof which is proved to be other than as warranted; no allowance shall be made for any labor charges of Buyer for replacement of parts, adjustment or repairs, or any other work, unless such charges are
authorized in advance by DX Engineering. If DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering shall, upon prompt notice thereof, issue shipping instructions for return to DX Engineering
(transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by Buyer unless made in writing. The above warranties shall not extend to any products or parts thereof which have been
subjected to any misuse or neglect, damaged by accident, rendered defective by reason of improper installation, damaged from severe weather including floods, or abnormal environmental conditions such as prolonged exposure to corrosives or
power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any goods or parts thereof furnished by Buyer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties do
not extend to other equipment and parts manufactured by others except to the extent of the original manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof. These
warranties provide exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER
EXPRESS, STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT
STRICTLY IN ACCORDANCE WITH THE FOREGOING.

©DX Engineering 2019

DX Engineering®, DXE®, DX Engineering, Inc.®, Hot Rodz®, Maxi-Core®, DX Engineering THUNDERBOLT®, DX Engineering Yagi Mechanical®, EZ-BUILD®, TELREX®, Gorilla Grip® Stainless Steel Boom Clamps, Butternut®, SkyHawk™,
SkyLark™, SecureMount™, OMNI-TILT™, RF-PRO-1B®, AFHD-4® are trademarks of PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and product names are
the trademarks of their respective owners.

Specifications subject to change without notice.

DXE-LP1-2C-INS Rev.0

DX Engineering - 1200 Southeast Ave. - Tallmadge, OH 44278 USA

Phone: [phone] ∙ Tech Support and International: [phone]

Fax: [phone] ∙ E-mail: [e-mail]