DX Engineering DXE-AOK-TB1193 Instructions manual

Wing Nut Knobs - Add-on Kit

DXE-AOK-TB1193 (pack of 2)

For No-Tools operation of the DXE-Tilt Base

(NOT for the MBVE-5 Saf-T-Tilt Base, NOT for the OMNI-TILT Tilt Base)

Designed to allow quick release of the Tilt Base (DXE-TB3P/4P/6P/7P/8P)

when lowering the antenna for tuning or stealth operation.

1. Loosen the bottom two Nyloc Nuts approximately 1/2 turn to allow
normal Tilt Base to operation.

2. Remove the two Nyloc Nuts at the top of the Tilt Base.

3. Remove one of the Flange Nuts and install one of the new Wing Nut Knobs. Hand tighten. Repeat this for the
other Flange Nut and Wing Nut Knob.

4. Thread the Flange Nuts & Nyloc Nuts removed in Step 3 onto the lower bolts
so they will not get misplaced.

DXE-AOK-TB1193-INS Rev 0c - 1 -

Available Accessories from DX Engineering

*PTX-81343

Anti-Seize, 1 oz. Squeeze Tube

*JTL-12555

Jet-Lube SS-30 Anti-Seize, .25 lb

*DXE-NSBT8

Never-Seez, 8 oz.

*DXE-NMCBT8

Never-Seez, 8 oz. Marine Grade

PTX-81343, JTL-12555, DXE-NSBT8, DXE-NMBT8 - Never-Seez & Anti-Seize

An anti-seize compound MUST be used on any Stainless Steel nuts, bolts, clamps or other
hardware to prevent galling and thread seizure. Any of these products can be used for this purpose.

* shipping restrictions may apply to this part

Technical Support

If you have questions about this product, or if you experience difficulties during the installation, contact DX
Engineering at [phone]. You can also e-mail us at:

[e-mail]

For best service, please take a few minutes to review this instruction sheet before you call.

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a
period of one (1) year from date of shipment. DX Engineering’s sole obligation under these warranties shall be to issue
credit, repair or replace any item or part thereof which is proved to be other than as warranted; no allowance shall be made
for any labor charges of Buyer for replacement of parts, adjustment or repairs, or any other work, unless such charges are
authorized in advance by DX Engineering. If DX Engineering’s products are claimed to be defective in material or
workmanship, DX Engineering shall, upon prompt notice thereof, issue shipping instructions for return to DX Engineering
(transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by
Buyer unless made in writing. The above warranties shall not extend to any products or parts thereof which have been
subjected to any misuse or neglect, damaged by accident, rendered defective by reason of improper installation, damaged
from severe weather including floods, or abnormal environmental conditions such as prolonged exposure to corrosives or
power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any goods or parts

thereof furnished by Buyer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties do

not extend to other equipment and parts manufactured by others except to the extent of the original manufacturer’s warranty
to DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof. These warranties
provide exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential damages.
SELLER NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS,
STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO
PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT
STRICTLY IN ACCORDANCE WITH THE FOREGOING.

©DX Engineering 2018

DX Engineering®, DXE®, DX Engineering, Inc.®, Hot Rodz®, Maxi-Core®, DX Engineering THUNDERBOLT®, DX
Engineering Yagi Mechanical®, EZ-BUILD®, TELREX®, Gorilla Grip® Stainless Steel Boom Clamps, Butternut®,
SkyHawk™, SkyLark™, SecureMount™, OMNI-TILT™, RF-PRO-1B®, AFHD-4® are trademarks of PDS Electronics, Inc.
No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and product
names are the trademarks of their respective owners.

Specifications subject to change without notice.

DX Engineering 2018

1200 Southeast Ave. - Tallmadge, OH 44278 USA

Phone: [phone] ∙Tech Support and International: [phone]

Fax: [phone] ∙ E-mail: [e-mail]

DXE-AOK-TB1193-INS Rev 0c - 2 -