Duratrax IntelliPeak Mini Pulse DC Only User Manual

•

Advanced fuzzy logic peak detector with
automatic cut-off circuit featuring high
efficiency P-Channel MOSFET drive

transistors

•

8-bit 4MHz CPU with 8K ROM, 1K RAM,
1-channel 16-bit analog-to-digital converter

•

8-bit pulse width modulated charge current to
charge NiCd or NiMH batteries to 100%
without overcharging

•

Built-in Artificial Intelligence to eliminate
false

peaks

•

11-15V DC input

•

Output: 4-7 cells on DC

•

Adjustable fast charge current:0.5-4.5 amps

•

100mA trickle charge

•

2 amp fixed discharge rate

•

Cycle functions: Select a single

discharge/charge
cycle for periodic pack conditioning, or
continuous “auto-repeat” cycles for reviving
batteries that have developed a memory or for
breaking in a new pack

•

Four multi-function, high intensity LED’s and
audible tones for easy set-up

•

Built-in miniature fan keeps charger cool,
increasing efficiency and lifespan

•

Fused overload and reverse polarity protection

•

Charge only nickel-cadmium or nickel-metal
hydride rechargeable batteries. Damage may
occur from other types of batteries.

•

Do not use automotive type battery chargers to
power the charger.

•

Do not allow water, moisture or foreign objects
into the charger.

•

Do not cover the air intake holes on the charger.
This will cause the charger to overheat.

•

Do not charge batteries containing fewer than
4 cells

•

Always connect the power source first.

•

Do not use a cable longer than 30cm to
connect the charger with the batteries.

•

Do not leave the charger unattended while
charging. Disconnect the battery

immediately if

the charger becomes hot. Allow the charger or

battery to cool down before reconnecting.

•

Keep out of reach of children.

•

Do NOT discharge cells smaller that sub-C
size cells.

The IntelliPeak Mini Pulse
Charger is capable of charging

both nickel-cadmium (NiCd)
and nickel-metal hydride (NiMH) battery
chemistries, as identified by this symbol. Look
exclusively for battery chargers with this symbol to
handle both NiCd and NiMH charging needs.

While similar in appearance to sub-C NiCd
batteries, NiMH batteries have a different internal
chemistry and require a different charging method.

It is important not to allow NiMH batteries to
overheat while being charged. Heat can

adversely
affect the performance of NiMH batteries. When
charging NiMH batteries with the IntelliPeak Mini
Pulse Charger, do not adjust the PEAK CHARGE
AMPS adjustment knob above 3.0 amps.Charging
at a higher amperage will heat up the batteries and
could cause permanent damage. If overheating is
observed, disconnect the battery from the charger
immediately, and reduce the charge rate for future
charging needs. Also, do not deep cycle NiMH
batteries. Permanent damage could result. Store
NiMH packs with some voltage remaining on the
cells.Use a NiMH battery pack no more than three
cycles per day, with a two to three hour break
in-between for cooling. More frequent use is likely
to overheat the pack.

To use a DC power supply or 12V DC battery for
input power, connect the DC adapter cord
(included) to the lead exiting the rear of the
charger.Attach the red alligator clip to the positive
(+) terminal on the power supply, and the black
alligator clip to the negative (-) terminal. It’s best to
use a clean DC power source whose output is
filtered to remove unwanted electrical noise.
Disconnect the DC input adapter cord from the
charger when not in use.

To use with 110V AC input power, the IntelliPeak
Mini Pulse Charger is directly compatible with
DuraTrax’s 12V, 7A Compact Switching Power
Supply (DTXP4300). See your local hobby shop
for details.

The IntelliPeak Pulse Charger is fuse protected
from current overload.Only replace the spade type
automotive fuse with one of the same 7A rating
and physical size. CAUTION: Disconnect the

charger from the input power source and the
load battery from the charger before replacing
the fuse.

The output lead (included) has a standard style
connector at one end, with the opposite wire ends
stripped so a small portion of bare wire is showing.
Insert the red, positive (+) wire into the red spring
loaded terminal on the front of the charger. Install
the black, negative (-) wire into the black spring
loaded terminal. These terminals allow virtually
any other charge leads to easily be connected to
the charger if so desired. CAUTION: Make sure

wire strands never make connection between
the red and black terminals! Failure to do so

could result in a short circuit condition, causing the
fuse to blow or permanent damage to the charger
and/or battery.

The IntelliPeak Mini Pulse Charger offers a slow
100mA trickle charge rate for charging a new
battery or topping off a previously charged battery.
Connect the battery to the charge lead on the front
of the charger. The green SLOW CHARGE LED
should automatically begin to flash, indicating
trickle charge is in progress. A 1500mAh batter y
should reach full charge in approximately 15 hours
using this charge method.

This unit has a high-rate fast charge to recharge a
partially discharged battery, with circuitry designed
to monitor pack voltage and automatically
terminate fast charge when full charge is reached.
Select the desired charge rate using the PEAK
CHARGE AMPS adjustment knob. Connect the
battery to the charge lead on the front of the
charger. The green SLOW CHARGE LED should
automatically begin to flash, indicating trickle
charge is in progress. Push the MODE SELECT
button once to start peak charging. The red PEAK
CHARGE LED should light, and the charger will
beep once to confirm peak charge is in progress.
When this LED begins to flash the battery is
approaching peak charge. This should soon be
followed by occasional flashing of the STATUS
LED, where each flash represents instantaneous
moments when actual battery voltage is starting to
decline, thus indicating the battery has reached
peak and the charger will soon return to slow
charge automatically.

WARNING: Do not leave charger unattended
during fast charge. If the battery or charger
become hot at any time, disconnect the battery
from the charger immediately! Failure to do so

may cause permanent damage to the charger and
battery, and may cause bodily harm. Reduce the
charge rate for future charging needs.

PEAK CHARGING

SLOW CHARGING

OUTPUT LEAD

FUSE PROTECTION

AC INPUT POWER (OPTIONAL)

DC INPUT POWER

IMPORTANT CARE AND HANDLING

INSTRUCTIONS FOR NIMH BATTERIES

IMPORTANT PRECAUTIONS

SPECIAL FEATURES

Congratulations on your purchase of the IntelliPeak™Mini Pulse Charger by DuraTrax®! With intelligently designed features to provide increased performance
and convenience, the IntelliPeak Mini Pulse Charger is well suited for a variety of modeler applications.

Discharging removes charge from a battery for
storage or conditioning purposes. Connect the
battery to the lead on the front of the charger.Push
and hold the MODE SELECT button for two
seconds.The charger will beep two times, and the
amber DISCHARGE LED will light, confirming
discharge is in progress at a fixed rate of 2 amps.
When the battery is finished discharging, the

charger

will automatically switch to slow charge mode.
The IntelliPeak Charger has a fixed, non-

adjustable
discharge cutoff voltage setting of 2.60V. If a
specific discharge cutoff value other than 2.60V is
desired, monitor the pack voltage during discharge
with a separate voltmeter and manually terminate
discharge at such point as desired.This step must
be followed during all cycling functions as well if a
different cutoff voltage is desired.

WARNING: Do NOT discharge cells which are
smaller than sub-C size. The discharge current

rate of the IntelliPeak is too high for smaller cells
such as A, AA, and AAA size, in addition to the
wiring used to assemble such packs.Failing to avoid
this will likely cause permanent damage to the cells
and/or wiring in the battery packs, and possibly the
equipment in which the battery is installed.

Use the single cycling feature to conduct a single
discharge/charge cycle for periodic pack
conditioning of regularly used batteries. Select the
desired charge rate using the PEAK CHARGE
AMPS adjustment knob.Then, connect the battery
to the charge lead on the front of the charger.Push
the MODE SELECT button twice. The amber
DISCHARGE LED will light and the charger will
beep three times to confirm single cycling is in
progress. When discharge is complete, it will
automatically switch to peak charging, confirmed
by the red PEAK CHARGE LED and a single beep.
This LED will flash when the battery nears

peak

charge, after which the charger will

automatically
return to slow charge as indicated by the flashing
green SLOW CHARGE LED.

Auto-repeat cycling lets you conduct repeated
discharge/charge cycles for deep pack
conditioning to break in new packs or revive older
or unused packs which may have developed
memory. Select the desired charge rate using the
PEAK CHARGE AMPS adjustment knob. Then,
connect the battery to the charge lead on the front
of the charger. Push the MODE SELECT button
twice and hold it down for two seconds.The amber
DISCHARGE LED will light and the charger will
beep four times to confirm auto-repeat cycling is in
progress. After the battery has finished
discharging it will automatically switch to peak
charge mode, confirmed by the red PEAK
CHARGE LED and a single beep. When this LED
begins to flash, the battery is approaching peak
charge. This should soon be followed by
occasional flashing of the STATUS LED, where
each flash represents instantaneous moments
when actual battery voltage is starting to decline,
thus indicating the battery has reached peak and
the charger will soon return to slow charge
automatically. Once peak charge has completed,
the charger will automatically repeat this entire
discharge/charge process.To end this function, the
user must push the MODE SELECT button or
disconnect battery from the charger.

To discharge the battery for storage, allow the
battery to cycle the desired amount of times and
then push the MODE SELECT button until the
orange DISCHARGE LED lights. This will start
discharge mode only. To peak charge the batter y,
wait until the last desired cycle is over and then
push the MODE SELECT button until the red
PEAK CHARGE LED lights.

The IntelliPeak Mini Pulse Charger is capable of
charging 9.6V transmitter batteries. This is best
accomplished when using 110V AC input through
the optional AC power supply from DuraTrax
(DTXP4300), or DC input power of greater than
12V but less than 15V. Connect the appropriate
adapter (not included) into the spring terminals on
the front of the charger. CAUTION: Failure to

recognize proper polarities will cause
permanent damage to the battery and/or

radio!

Tur n the PEAK CHARGE AMPS

adjustment knob
down to 0.5 amps to allow the batteries to peak
charge.Charging at a higher amperage can cause
permanent damage to the transmitter batteries.Do
not allow standard capacity TX batteries to remain
in slow charge mode in excess of 1 hour after peak
charge has been reached, as overheating of the
battery might occur.Note: If your transmitter has

a diode in the charge circuit, it may be
necessary to remove this diode to allow your
transmitter to receive a full charge with this
IntelliPeak charger. In addition, the battery will
NOT accept a discharge with the diode in the
circuit. Removal of the diode will allow a full
charge and discharge.

WARNING: Do NOT discharge transmitter
batteries with the IntelliPeak Charger. The

discharge current rate is too high for such smaller
cells and the wiring which is used to assemble
such packs. Failing to avoid this will likely cause
permanent damage to the cells and/or wiring in the
battery packs, and possibly the equipment in
which the battery is installed.

Input Voltage: 11-15V DC
Output: 4-7 cells DC
NiCd Fast Charge: 0.5-4.5A
NiMH Fast Charge: 0.5-3.0A
Tr ickle Charge Rate: 100mA
Discharge Rate: 2 Amp fixed
Discharge Cutoff
Voltage: 2.60V fixed
Battery Types: Nickel-cadmium (NiCd) &

nickel-metal hydride (NiMH)
Case Size: 3.38" x 1.88" x 3.5"
Weight: 7.6 oz. (without power

supply)

Part Number: DTXP4109

DuraTrax warrants this product to be free from
defects in materials and workmanship for a period
of 1 year from the date of purchase. Dur ing that
period, we will repair or replace , at our option, any
product that does not meet these standards. You
will be required to provide proof or purchase date
(receipt or invoice).If during the 1 year period, your
DuraTrax product shows defects caused by abuse,
misuse, or accident, it will be repaired or replaced
at our option, at a service charge not greater than
50% of the current retail price. Be sure to include
your daytime telephone number in case we need
to contact you about your repair. This warranty
does not cover components worn by use,
application of reverse voltage, cross connections,
poor installation, subjection of components to
foreign materials, any alterations to wires, or
tampering. In no case shall our liability exceed the
original cost of the product.
Your warranty is voided if...

A. You allow any wires to become frayed which

could cause a short
B. You tamper with any of the electronic components .
C. You exceed minimum or maximum cell

specifications for the battery pack.
D. You allow water, moisture, or any foreign

material to enter the charger case.
E. You apply reverse voltage by connecting the

battery pack backwards.

Under no circumstances will the purchaser be
entitled to consequential or incidental damages.
This warranty gives you specific legal rights, and
you may also have other rights which vary from
state to state. If you attempt to disassemble or
repair this unit yourself it may void the warranty.
For service to your DuraTrax product, either in or
out of warranty, send it post paid and insured to:

HOBBY SERVICES

3002 N. Apollo Dr., Suite 1

Champaign, IL 61822

[phone]
e-mail: [e-mail]
Internet Address: www.duratrax.com

WARRANTY

SPECIFICATIONS

TRANSMITTER BATTERIES

AUTO-REPEAT CYCLING

SINGLE CYCLING

DISCHARGING

LED DISPLAY

Condition Discharge LED Fast Charge LED Slow Charge LED Status LED

(Yellow) (Orange) (Green) (Red)
No Battery OFF OFF OFF ON
Slow Charging OFF OFF OFF: When batter y On: Normal

is < 3V Flash: Bad battery

Flash: Slow Charging connection

Off: Weak power

supply

Fast Charging OFF ON: Battery is charging OFF On: Battery voltage is

Flash: Battery is increasing or stable

near peak Off: Battery voltage is

decreasing

Discharging ON OFF OFF ON

DTXZ4109 for DTXP4109 V1.0