Duratrax DTXP3110 Instructions Manual

DuraTrax’s Frequency Checker is designed to scan all thirty
R/C frequencies in the 75MHz band and identify when another
transmitter is operating on any such channel. It’s important

to note that the Frequency Checker is NOT well suited to
show very brief, intermittent Rf signals that could cause
interference which may be present in the environment
near or between R/C channels.

Input voltage:

4.5V DC

Operational current:

20 - 90mA

Frequency identifiers:

30 individual red LEDs

Scan frequency:

9 seconds

Max. operational temp:

32-104°F (0-40°C)

Dimensions:

3.14"x.94"x2.36" (80x24x60mm)

Weight:

2.05 oz. (58g)

• Each frequency is identified by its own dedicated LED

• No programming or adjustments, for ease of use–
automatically scans all frequencies when power is applied

• Requires 3 “AAA” alkaline cells (not included)

• Range is up to 300 feet w/o exter nal antenna

• Range is up to 1000 feet with exter nal antenna, available
separately (DTXP3111)

• Small and lightweight, easily fits in a pocket or pit box

• Do not fly on a frequency that is already in use! Failure to
obey this warning can and likely will result in crashed models.

• Always test your radio system before use by performing a
complete range check to make sure there is a solid Rf link
between the transmitter and receiver. Refer to your radio’s
instruction manual for further details.

• Do not allow fuel or oil to make contact with the Frequency
Checker’s plastic case, as it could result in damage to the
case or the artwork.

• Do not store the frequency checker in extreme heat (e xceeding
104°F) or cold (below -14°F), in direct sunlight, in high humidity,
in high vibration environments or in dusty areas.

• Do not point a Tx antenna directly at the Frequency Checker.
This will make it more difficult for the checker to detect the
signal being emitted from the Tx.

• For best reception do not lay the Frequency Checker on the
ground during operation. Resting the checker on an elevated
surface such as a table or pit box is recommended.

The 75MHz Frequency Check er requires
3 “AAA” sized alkaline batteries. Looking
at the rear of the Frequency Checker,
press the tab on the battery door, then
gently remove the door. Pay close
attention to insert the cells in the proper
direction as shown here. Re-install the
door after all batteries are installed. If the
condition of the batteries is in doubt,
install fresh batteries for optimum
performance before use.

ON/OFF SWITCH

The input power switch is located along the right side of the
Frequency Checker. Slide the switch to the upper position to
turn the unit on. Move the switch to the lower position to turn
the unit off.Make sure to turn the power switch off when not in
use to prevent draining the batteries.

LEDS

Each of the 30 channels in the 75MHz band is represented on
the Frequency Checker by its own dedicated red LED. The
Frequency Checker scans all frequencies in the band one-by­one.This device does NO T scan all frequencies instantaneously.

When the power switch is turned on, the Checker begins the
scan starting at channel 61 (75.410MHz) as indicated by a
brief flash of the LED marked “61”, then steps to channel 62
(75.430MHz), etc. until it reaches channel 90 (75.990MHz),
after which time it will start over again at channel 61. It takes
approximately 9 seconds for the Frequency Checker to scan
through all 30 frequencies. The Checker will continue this
scanning process until the power switch is turned off.

When the Frequency Checker identifies that a frequency is in
use, the LED for that particular channel will stay on. This
means it is not safe to use that respective channel! The
Checker will then continue to scan the next channels in order,

OPERATION

INSTALLING BATTERIES

IMPORTANT PRECAUTIONS

SPECIAL FEATURES

SPECIFICATIONS

INTRODUCTION

75MHz INSTRUCTIONS

®

LED

ON/OFF
SWITCH

and if a signal is detected on another channel its LED will stay
on solid as well. For example, it is possible that all 30 LEDs
could stay on if a signal is detected on all 30 channels,
although such a circumstance is highly unlikely. Each LED will
stay on until the Checker scans through all other remaining
channels and back again, at which time the scan will start over .
If during the next scan of that channel the signal disappears the
LED will turn off. For reference, see the list below to match the
channel number to its respective frequency in the 75MHz band:

The 75MHz Frequency Checker has a built-in antenna which
is designed to receive transmitter signals from within a 300
foot radius. If a greater range is desired, an external antenna
is available separately (DTXP3111). Contact your local hobby
shop for details. Using the external antenna can extend the
Frequency Checker’s range to a radius of 1000 feet. It's best
to point the antenna skyward for best reception.

When using the external antenna, extra channels might appear
to be in use if the checker is physically located ver y near a Tx
which is emitting a signal. Moving the checker several feet
away from the Tx should clear the problem. If used inside
buildings which have a lot of steel/metal in the structure, extra
channels might inadvertently be shown, and NOT using the
external antenna may deliver the best results in this situation.

When used inside enclosed buildings, particularly those
constructed with a steel structure and covered with a metallic
surface, it’s possible that the Frequency Checker might show
some erratic behavior. Such facilities can cause excessive
reflection of Rf signals, and might cause the Frequency
Checker to indicate that some frequencies are being used
when, in fact, they might not be. This condition will typically
worsen as more transmitters are in use.

PROBLEM: Unit does not seem to function at all.

CAUSES AND CURES:

1. Power switch turned off. Turn power switch on.

2. Batteries may be weak or dead. Replace batteries.

3. Batteries may be installed improperly .Re-install batteries
in proper configuration.

4. Internal problem. Contact Hobby Services.

PROBLEM: Short range.

CAUSES AND CURES:

1. Batteries may be weak. Replace batteries.

2. Internal antenna may be insufficient for particular area.
Purchase of external antenna may be necessary.

3. External antenna not fully extended. Extend antenna.

PROBLEM: LEDs are faded, or cer tain LEDs not functioning.

CAUSES AND CURES:

1. Batteries may be weak. Replace batteries.

2. Internal damage. Contact Hobby Services.

PROBLEM: Unit indicates more frequencies are in use than

are being used by modelers in the area.

CAUSES AND CURES:

Many channels are being used
simultaneously in a “noisy” Rf environment, such as inside
a metal structure. Reduce the number of racers driving at
one particular time. Do not use the external antenna in
such instances as it could exaggerate the effect of the
noisy environment.

This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions.

1.This device may not cause harmful interference.

2.This device must accept any interference received,
including interference that may cause undesired oper ation.

DuraTrax warrants this product to be free from defects in materials and
workmanship for a period of one (1) years from the date of purchase.During that
period, DuraTrax will, at its option, repair or replace without service charge any
product deemed defective due to those causes. You will be required to provide
proof of purchase (invoice or receipt). This warranty does not cover damage
caused by abuse, misuse, alteration or accident.If there is damage stemming
from these causes within the stated warranty period, DuraTrax will, at its option,
repair or replace it for a service charge not greater than 50% of its then current
retail list price. Be sure to include your daytime telephone number in case we
need to contact you about your repair. This warranty gives you specific rights.
You may also have other rights, which vary from state to state.

For service on your DuraTrax product, warranty or non-warranty, send it post­paid and insured to:

HOBBY SERVICES

3002 N. Apollo Drive Suite 1

Champaign, IL 61822

[phone]

*For warranty and service information if purchased outside the USA or
Canada, see the additional warranty information insert (if applicable) or ask
your retailer for more information.

www.duratrax.com

1-YEAR LIMITED WARRANTY

*U.S.A. AND CANADA ONLY

FCC STATEMENT

TROUBLESHOOTING GUIDE

INDOOR RACE TRACKS

ANTENNAS

Channel Freq

11 72.010
61 75.410
62 75.430
63 75.450
64 75.470
65 75.490
66 75.510
67 75.530
68 75.550
69 75.570

70 75.590
71 75.610
72 75.630
73 75.650
74 75.670
75 75.690
76 75.710
77 75.730
78 75.750
79 75.770
80 75.790

81 75.810
82 75.830
83 75.850
84 75.870
85 75.890
86 75.910
87 75.930
88 75.950
89 75.970
90 75.990

ENTIRE CONTENTS © Copyright 2005 Made in Korea DTXZ4101 for DTXP3110 v1.1

Frequency Checker

FOR HOME OR OFFICE USE

HCAP0340
DTXP3110

Tested to Comply
With FCC Standards