Duraflame DFI-8511-02, DFI-8511-01, DFI-8511-03, DFI-8511-05, DFI-8511-04 Assembly And Operating Instructions Manual
...
MODELS: DFI-8511-01, DFI-8511-02, DFI-8511-03, DFI-8511-04,DFI-8511-05,DFI-8511-06
- POWER
Made in China
Printed in China
© 2014,Twin-Star International,Inc.
3. Pinch this spring clip to
loosen. Gently turn and pull the
rubber grommet of the motor
shaft.
REPLACING THE LIGHT BULB
VOLTAGE 120 VAC, 60 Hz
AMPS 12.5 Amps
WATTS 1500 Watts
OPERATING INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
PRODUCT SPECIFICATIONS
•Use the power button to turn on or off the stove
from the remote or control panel.
•Use the + and - buttons to adjust the ame
brightness.
- FLAME
For Customer Service:
www.twinstarhome.com
888-674-7517
8:30 a.m.-5:30 p.m., EST, Monday-Friday
Pull
Pull
Light bulb retaining spring
1. Loosen Phillips head screws
and remove back panel.
2. Remove back panel to access
light bulb
Distributed by
Twin-Star International, Inc. Under license.
duraflame™ and the duraflame flame
logo are trademarks of Duraflame, Inc.
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China • Printed in China
MOUNTING THE LEGS
1. Align the 2 mounting tabs into the bracket (Fig 1)
2. Slide the legs outward to lock in place. The legs will snap into place
when correctly installed. (Fig 2)
3. Fasten the legs to the base using the included screws,1 per leg. If the
screw hole does not line up check that the legs are properly snapped
into place. (Fig 3)
Note: When rst running the heater there can
be an odor. This is normal, the heater has a
surface coating on the internal parts, for the
rst several hours of operation the coating
reacts with the internal parts to permanently
protect them. The odor is safe; if you are
sensitive to the odor it is recommended
to run the heater in a well-ventilated area
until the odor dissipates.
Warning: This is an unvented, electric appliance.
DO NOT attempt to burn wood or manufactured
relogs in or on this appliance or grate.
1
Leg
Bracket
2
3
4. Pull away the bulb retaining
spring, unscrew the old bulb,
and replace with a new 40w
candelabra bulb.
Spinner
Motor
Assembly
Light bulb
-HEATER
•Press the HEATER button to cycle through 1000W,
1500W and OFF.
•The heater will beep once when set to 1000W,
twice for 1500W, and three times for OFF.
Go to www.tsicustomerservice.com for product warranty registration
1-YEAR LIMITED WARRANTY
The manufacturer warrants that your new Electric Stove is free from manufacturing and material defects for a period of one year from date of puchase, subject to the following
conditions and limitations.
1. Install and operate this Electric Stove in accordance with the installation and operating instructions furnished with the product at all times. Any unauthorized repair, alteration,
willful abuse, accident, or misuse of the product shall nullify this warranty.
2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was made through an authorized supplier of the product.
3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship, provided that such part(s) have been subjected to normal
conditions of use and service, after said defect is conrmed by the manufacturer’s inspection.
4. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s).
5. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement, or othe wise of same, will not be covered
by this warranty, nor shall the manufacturer assume responsibility for same.
6. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or damage arising out of the use, or inability to use the product,
except as provided by law.
7. All other warranties – expressed or implied –with respect to the product, its components and accessories, or any obligations/liabilities on the part of the manufacturer are
hereby expressly excluded.
8. The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities with respect to the sale of the product.
9. The warranties as outlined within this document do not apply to non accessories used in conjunction with the installation of this product.
This warranty is void if:
a. The replace is subjected to prolonged periods of dampness or condensation.
b. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
c. You do not have the original receipt of purchase.
IF WARRANTY SERVICE IS NEEDED
Contact the manufacturer by calling customer service department at 1-888-674-7517, 7 days a week/24 hours a day/
365 days per year. Make sure you have your warranty, your sales receipt, location of purchase and the model/serial number of
your product.
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. If provided, use handles when moving this appliance. Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes and curtains at least
3 feet (0.9 m) from the front of this appliance. WARNING: In order to avoid
overheating, do not cover the heater.
3. CAUTION: Never leave the heater operating unattended. Extreme caution is
necessary if unsupervised children or invalids are nearby.
4. The appliance is not to be used by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction.
5. Always unplug this appliance when not in use.
6. Do not operate any heater with a damaged cord or plug or after the appliance
malfunctions, or if it has been dropped or damaged in any manner.
7. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a hazard.
8. Do not use outdoors.
9. This heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. Never locate this appliance where it may fall into a bathtub or other
water container.
10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the
like. Arrange cord away from trafc areas and where it will not be tripped over.
11. To disconnect this appliance, turn controls to the off position, then remove plug
from outlet.
12. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as
this may cause an electric shock or re, or damage the appliance.
13. To prevent a possible re, do not block air intakes or exhaust in
any manner. Do not
use on soft surfaces, like a bed, where opening may become blocked.
14.This appliance has hot and arcing or sparking parts inside. Do not use it in areas
where gasoline, paint or ammable liquids are used or stored. This stove should
not be used as a drying rack for clothing. Christmas stockings or decorations
should not be hung in the area of it.
15.Use this appliance only as described in the manual. Any other use not
recommended by the manufacturer may cause re, electric shock or injury to
persons.
16. This appliance, when installed, must be electrically grounded in accordance with
local codes or, in the absence of local codes, with the current CSA C22.2
Canadian Electrical Code or for U.S.A. installations, follow local codes and the
National Electrical Code, ANSI/NFPA NO.70.
17.Connect to properly grounded outlets only, See Fig.1.This heater is for use on 120
volts. Do not use a 2 prong adapters. Always plug heaters directly into a wall
outlet/receptacle.Never use with an extension cord or relocatable power tap
(outlet/power strip).
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electrical shock, and injury to persons including the following:
Battery Replacement
Note: Batteries should be removed if the product is to be left unused for a long time.
1. The battery compartment is located on the back end of the remote control.
2. Press and slide the battery door open and remove the old battery.
3. Insert 2 AAA batteries, checking that the + and - sides of the battery match
inside the battery compartment.
4. Replace the battery compartment door.
Note: Do not mix old and new batteries. Do not mix alkaline, standard (carbon zinc),
or rechargeable (nicad, nimh, etc) batteries.
DISPOSAL OF USED BATTERIES
Battery may contain hazardous substances which could endanger the
enviroment and human health. Used batteries shall not be treated as municipal waste,
but left at the appropriate collection point for recycling.
For more information about collection and recycling of used batteries,
please contact your local municipality or waste disposal service.
Warning: Changes or modications to this unit not expressly approved by the party responsible for
compliance could void user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. if this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation. Modications not approved by the party responsible for compliance could
void user’s authority to operate the equipment.
SAVE THESE
INSTRUCTIONS
A
B
Fig.1
Loading...