Duracraft Baby's Breath Vaporizer DH-711, Baby's Breath DH-712 Series, Baby's Breath DH-722 Series, Baby's Breath DH-721 Series Owner's Manual

OWNER’S MANUAL

BABY’S BREATH™

VAPORIZER

Models DH-711, DH-712, DH-721 and DH-722 Series

DH-711

READ ALL INSTRUCTIONS BEFORE USING THIS HUMIDIFIER AND SAVE THESE
IMPORTANT INSTRUCTIONS FOR EASY REFERENCE.

WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY PRECAUTIONS
SHOULD BE FOLLOWED INCLUDING:

1. Always place this vaporizer on a firm, flat, and level surface, at least 4 feet
away from any person. It may not work properly on an uneven surface.

2. RISK OF INJURY TO PERSONS–DO NOT TOUCH STEAM VAPOR-STEAM CAN
CAUSE BURNS.

Place this vaporizer in an area where it is not accessible to

children. Never point the steam outlet directly toward any person.

3. Do not place the vaporizer near any heat sources such as stoves, radiators,
and heaters.

4. Before using the vaporizer, check the power cord for any signs of damage.
If the cord is found to be damaged,
DO NOT USE and return the vaporizer to Duracraft®under the warranty agree-
ment for repair. Never allow the power cord to be immersed in water or other
liquid.

5. This product is equipped with a polarized AC-line plug (a plug having one
blade wider than the other). This plug will fit into the power outlet only one
way.

This is a safety feature. NEVER connect the vaporizer to any power
source other than a 120V polarized outlet. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug should still fail to fit,
contact an electrician to replace the obsolete outlet.

DO NOT defeat the safety

purpose of the polarized plug.

6. Never plug in vaporizer without filling with water and always UNPLUG and
empty the vaporizer before moving, filling, cleaning, or storing.

UNPLUG the

vaporizer before removing the electrode heating assembly.

7. RISK OF FIRE–NEVER add salt to the water. This can cause excessive boiling
and electrical overloading of your household electrical system.

8. DO NOT add vaporizer medicine directly into the water. Place in the medicine
cup and fill it halfway. DURACRAFT

®

assumes no responsibility for conse-

quences resulting from the use of medications in this vaporizer.

9. Do not OVER-FILL the vaporizer. Doing so may result in electrical shock hazard.

10.

This vaporizer requires regular cleaning. Refer to the CLEANING instructions
provided. Never clean the vaporizer in any manner other than as instructed in
this manual.

11 .

Turn the vaporizer to OFF if the relative humidity exceeds 60%, or if you notice
moisture on the inside of your windows. For proper humidity readings use a
hygrometer which is available in many hardware and department stores, or by
ordering on from Duracraft

®

(see Care Products and Accessories).

IMPORTANT SAFETY INSTRUCTIONS

INTRODUCTION

Thank you for purchasing a Duracraft®Baby’s Breath™
Vaporizer manufactured by Honeywell. If you would like
more information on our full line of products please visit our
website at:

www.honeywell.com/yourhome.

MODEL DH-711, DH-712, DH-721 and DH-722

Your vaporizer is made up of two parts:

Base

Steam
Assembly

SET UP

NOTE: We recommend that the humidifier be disinfected prior to first use.

Please see CLEANING instructions.

• Select a firm, level, flat location — at least six inches (15 cm) from any wall

for proper air flow and convenient to an electrical outlet (Fig. 1).

Place vaporizer where it is out of the reach of children. Make sure cord is
not in an area where it can be tripped over or pulled on. Be sure that the
steam outlet is pointed away from any person.

• Place the vaporizer on a water-resistant surface, as water can damage

furniture and some flooring. Duracraft

®

will not accept responsibility for

property damage caused by water spillage.

Fig. 2

1. To remove the Steam Assembly, hold the Base and turn the Steam Assembly

counter-clockwise then pull up.

2. Fill the Base with COOL tap water to the indent marked “Full Level” located on

the back of the unit (Fig. 2).

DO NOT USE HOT WATER. Doing so may

damage the vaporizer.

3. Replace the Steam Assembly back onto the Base. Turn it clockwise

to lock in place. Once the Steam Assembly has been positioned, do not
attempt to move vaporizer. If it has to be moved, unplug it and empty the
Base first.

CAUTION: DO NOT PLUG IN THE HUMIDIFIER WITH WET HANDS AS AN

ELECTRIC SHOCK COULD OCCUR.

4. Plug the filled vaporizer into a polarized 120V outlet. DO NOT FORCE THE

POLARIZED PLUG INTO THE OUTLET; it will only fit one way.

FILLING

Fig. 1

Full Level
Indent

WALL

6" minimum