Du Pont WFQT13000 Series, WFQT13500 Series Installation Instruction Manual

Installation Instructions

QuickTwist

™

1 Stage Drinking Water Filtration System & Direct Flow 1 Stage Drinking Water Filtration System

Instrucciones de instalación Sistema de filtrado de agua potable de 1 etapa QuickTwist

™

y dirija el sistema de la

filtración del agua potable de la etapa del flujo 1

Model Series WFQT13000 and WFQT13500

Serie del modelo WFQT13000 y WFQT13500

Water Filtration

V4.0

Package Contents

Installation Instructions

QuickTwist

™

1 Stage Drinking Water Filtration System

Parts & Hardware Included

Filter System Head with Built-in Bracket

B QuickTwist

™

Filter

C Mounting Screws D Faucet for Filtered Water E Black Rubber Gasket F Metal Lock Washer G Faucet Stem Nut H Kitchen Faucet Adapter I Insert J Ferrule K Compression Nut L 1/4" Plastic Tubing

Tools & Materials Required

n Phillips Screwdriver n 1/8" Drill Bit n Center Punch n Adjustable Wrench n Utility Knife n File n Tape Measure n Safety Glasses n Masking Tape n Newspaper or Towels n Pencil n Pan or Bucket n Compression Cap (Optional-For Kitchen Faucet

Spray Hose Connector)

Optional Materials

n Drill with 1/4" & 9/16" or 5/8" Drill Bits n Hollow-Wall Anchor Bolts or Toggle Bolts n Hacksaw n Plumber’s Tape

For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code CMR248 shall be adhered to.

www.waterfiltration.DuPont.com

Protect Plus, LLC n Hickory, NC 28601 USA

866-709-2086Toll Free

For Service Requests & Product Information Hours of Operation: 24 Hours/Day, 7 Days/Week

800-441-7515

For Safety & Health Questions

Information & Assistance

System Head with

Built-in Bracket

DuPont Part No. WFAH100

QuickTwist™

Filter

Faucet for

Filtered Water

Black

Rubber Gasket

Metal Lock Washer

Faucet Stem Nut

Insert

Ferrule

Compression Nut

Faucet Connector Set

DuPont Part No. WFAF600

1/4" Plastic Tubing

DuPont Part No. WFAF300 (6 Feet)

KFA-Kitchen Faucet Adapter

1/2" NPTF to 1/4" Tube

DuPont Part No. WFAF400

Mounting Screws

DuPont Part No. WFAS300

(Package of 2)

Package Contents

Installation Instructions

QuickTwist

™

Direct Flow 1 Stage Drinking Water Filtration System

Parts & Hardware Included

Filter System Head with Built-in Bracket

B QuickTwist

™

Filter

C Mounting Screws D 3/8” Male OD Adapter E 3/8” Female OD Adapter F 1/4” Plastic Tubing

Tools & Materials Required

Spray Hose Connector)

Optional Materials

n Drill with 1/4" & 9/16" or 5/8" Drill Bits n Hollow-Wall Anchor Bolts or Toggle Bolts n Hacksaw n Plumber’s Tape

For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code CMR248 shall be adhered to.

www.waterfiltration.DuPont.com

Protect Plus, LLC n Hickory, NC 28601 USA

866-709-2086Toll Free

For Service Requests & Product Information Hours of Operation: 24 Hours/Day, 7 Days/Week

800-441-7515

For Safety & Health Questions

Information & Assistance

1/4" Plastic Tubing

DuPont Part No. WFAF300 (6 Feet)

Mounting Screws

DuPont Part No. WFAS300

(Package of 2)

Syst

-i

. WFA

100

Twi

™

3/8" Male

OD Adapter

3/8" Female OD Adapter

Proper Installation

Please read all instructions, specifications, and precautions before installing and using your water filter system.

Precautions:

For cold water use only.

After prolonged periods of non-use (such as during a vacation), it is recommended that the Filter System be flushed thoroughly. Let water run for 10 minutes before using.

The QuickTwist™ Filter used with this Filter System has a limited service life. Changes in taste, odor, and/or flow of the water being filtered indicate that the filter should be replaced.

Before You Begin

n Check under the sink to locate a solid wall surface to mount the Filter System.

NOTE: The Filter System must be mounted in a vertical position.

n Locate the cold water pipe under your sink and observe if it is a flexible hose or a rigid pipe (ex: plastic, metal, copper). Rigid pipes

may require cutting in order to make adequate space to install the Kitchen Faucet Adapter (see Step 2). Also determine if you have all appropriate fasteners and adapters to fit your plumbing.

n Consult your local plumbing codes and install accordingly.

n If you plan to install your QuickTwist

WFDW13000 Series direct to your kitchen faucet please skip to page 10.

n If you purchased a QuickTwist

WFDW13500 Series and you plan to direct connect to your kitchen faucet please skip to page 10.

STEP 1

Turn Off the Main Water Supply Line

1 Locate the cold water shut-off valve under the sink. Turn off the cold water supply to the existing kitchen sink.

NOTE: If uncertain about which line supplies the cold water, turn on the hot water to the faucet. Allow the water to heat up and carefully feel the pipes under the sink. The pipe that remains cool to the touch is the cold water supply.

2 Turn on the cold water faucet on the kitchen sink to release pressure and allow water to completely drain from the line.

This filter must be protected from freezing, which can cause cracking of the filter and water leakage.

CAUTION

Because of the product’s limited service life and to prevent costly repairs or possible water damage, we strongly recommend that the head of the filter be replaced every ten years. If the head of the filter has been in use for longer than this period, it should be replaced immediately. Date the top of any new head to indicate the next recommended replacement date.

CAUTION

RIGID PIPE INSTALLATION

FLEXIBLE HOSE INSTALLATION

KITCHEN FAUCET

AUCET FOR

ILTERED WATER

OT WATER

VALVE

OLD WATER

VALVE

KITCHEN FAUCET

FAUCET FOR

FILTERED WATER

HOT WATER

VALVE

COLD WATER

VALVE

COLD WATER

VALVE

WFQT13000 & WFQT13500 Series

STEP 2 Mount the Faucet for Filtered Water

NOTE: The Faucet for Filtered Water in this package is designed to fit a 9/16" hole. Most standard sinks come with 1-3/8" or 1-1/2" diameter water sprayer holes that can be used for mounting the Faucet. If the pre-drilled holes cannot be used or are not in the desired position, a new hole must be drilled using either a 9/16" or 5/8" drill bit to accommodate the Faucet. The Faucet for Filtered Water base should be positioned securely on a flat surface with adequate space for proper function. Consider convenience and appearance of the faucet before installation.

IF YOUR SINK DOES NOT HAVE A WATER SPRAYER HOLE, GO TO

1. IF YOUR SINK DOES HAVE A WATER SPRAYER HOLE, GO TO 4.

1 In order to prevent parts and materials from falling down the drain, line the sink with newspaper or a towel.

2 Apply masking tape to the area to be drilled in order to prevent scratching the sink surface or countertop if the drill bit slips

during operation.

3 Using a center punch, mark the drill hole. Use the 1/4" drill bit to make a pilot hole. Then use the 9/16" or 5/8" drill bit to drill the final

hole. Drill completely through the sink or countertop and smooth the rough edges with a file.

NOTE: Make sure that the Faucet for Filtered Water is assembled. The Faucet for Filtered Water Spout should be inserted into the Faucet for Filtered Water Body and the retaining nut should be tightened until snug.

4 Guide the Black Rubber Gasket E onto the threaded Faucet for Filtered Water Stem. Slip the threaded Faucet Stem into the sink or

countertop hole. Make sure the Faucet for Filtered Water sits flat on top of the sink or countertop surface.

5 From underneath the sink, slide the Metal Lock Washer F up the Faucet for Filtered Water Stem. Then screw the plastic Faucet

Stem Nut

G all the way up the Faucet Stem until it is flush with the Metal Lock Washer. Screw until it is slightly snug and check

to make sure the faucet spout is in the proper position. Using fingers, tighten the nut to secure the Faucet for Filtered Water to the sink.

NOTE: Do not tighten the Faucet for Filtered Water Stem Nut with pliers as it may strip the Faucet Stem threads.

Safety glasses and a respirator are recommended for this process, as it may produce dust that can cause severe irritation if it is inhaled or comes in contact with eyes.

CAUTION

DO NOT DRILL THROUGH AN ALL-PORCELAIN OR CAST IRON SINK. If installing on an all-porcelain or cast iron sink, the faucet must be mounted in a pre-drilled sprayer hole or through the countertop next to the sink. If the countertop must be drilled, make certain that the area below the drilling location is free of wiring and pipes. Also, make sure that there is sufficient room to make the proper connections to the bottom of the faucet mount. DO NOT DRILL THROUGH COUNTER TOPS MORE THAN 1" IN THICKNESS OR COUNTERTOPS MADE OF TILE, MARBLE, GRANITE OR SIMILAR SUBSTANCE. Consult with a plumber or the countertop manufacturer for assistance.

CAUTION

FAUCET FOR

ILTERED WATER

POUT

BASE

V4.0

WFQT13000 & WFQT13500 Series

STEP 3

Install the Kitchen Faucet Adapter

NOTE: The Kitchen Faucet Adapter is designed to fit 1/2" NPTF supply threads.

1 Locate the cold water shut-off valve under the sink. Turn off the cold water supply to the sink.

2 Turn on the kitchen faucet to release pressure and allow water to completely drain from the line.

3 Disconnect the cold water line from the 1/2" threaded stem on the bottom of the kitchen faucet.

NOTE: If rigid plumbing pipe (metal or plastic) is used, you may need to shorten the pipe using a hacksaw to accommodate the Kitchen Faucet Adapter.

4 Holding the Kitchen Faucet Adapter H in an upright position (see diagram), screw onto the threaded faucet stem.

5 Screw the cold water supply line to the male threads of the Kitchen Faucet Adapter using the nut that was connecting the cold

water line to the kitchen faucet previously. For a secure fit, tighten the nut using an adjustable wrench.

6 If you have replaced your sprayer with the Faucet for Filtered Water be sure to cap off the sprayer outlet from the kitchen faucet.

Most faucets will require a compression cap to seal and prevent leaks.

STEP 4

Mount the System Head

1 Choose an easy-to-access area under the sink to mount the Filter System.

NOTE: To allow adequate space for filter changes, allow a minimum clearance of 4-6" below the QuickTwist™Filter. The Filter System must be mounted in a vertical position.

NOTE: Mount the Filter System to a solid cabinet wall or wall. If a solid surface is not available, use hollow-wall anchor bolts or toggle bolts (not included) to secure to the wall.

2 Remove the cap from the top of the System Head A. Using the Built-in Bracket on the back of the System Head or the template

provided on the back of this booklet, mark the holes for the Mounting Screws

C on the wall surface.

3 Using a 1/8" drill bit, drill two pilot holes for the Mounting Screws. Insert Mounting Screws into the wall with a Phillips screwdriver,

leaving approximately 3/8" of each Mounting Screw exposed.

4 Hang the System Head on the eyes of the bracket and replace the System Head cap.

Be sure that all electrical appliances and outlets are turned off at the circuit breaker before working in cabinet area.

WARNING

Please wear safety glasses to protect eyes when drilling.

CAUTION

RIGID PIPE INSTALLATION

4-6"

KITCHEN FAUCET

HOT WATER

VALVE

COLD WATER

VALVE

INLET OUTLET

WFQT13000 & WFQT13500 Series

STEP 5

Install 1/4" Plastic Tubing for Water Supply Line from Kitchen Faucet Adapter to System Head Inlet

1 Determine the length of 1/4" Plastic Tubing L that will be necessary to connect the System Head Inlet to the Kitchen Faucet

Adapter

H. Make sure to allow enough Plastic Tubing to prevent kinking in the line.

2 Cut the 1/4" Plastic Tubing squarely on both ends.

3 Wet one end of the 1/4" Plastic Tubing with water and push it into the Kitchen Faucet Adapter approximately 5/8" until it stops.

NOTE: Do not bend or crimp 1/4" Plastic Tubing when inserting.

4 Wet the other end of the 1/4" Plastic Tubing with water and push it into the System Head Inlet approximately 5/8" until it stops.

NOTE: The 1/4" Plastic Tubing does not need to be disconnected for general routine maintenance and filter replacement. However, Plastic Tubing may be easily disconnected if necessary. Simply turn off the water supply to the Filter System and press in the grey collar around the fitting while pulling the Plastic Tubing out with the other hand.

STEP 6

Install 1/4" Plastic Tubing for Water Supply Line from System Head Outlet to Faucet

1 Determine the length of 1/4" Plastic Tubing L that will be necessary to connect the System Head Outlet to the threaded Faucet

Stem. Make sure to allow enough Plastic Tubing to prevent kinking in the line.

2 Cut the 1/4" Plastic Tubing squarely on both ends.

3 Wet one end of the 1/4" Plastic Tubing with water and push it into the System Head Outlet until it stops.

4 Gently slide the plastic Compression Nut down G (thread side up) over the tubing. Follow with the plastic Ferrule J, making sure

that the Ferrule is in the proper position with the larger opening on the bottom (going into the nut). Place the plastic Insert

I into

the end of the 1/4" Plastic Tubing.

5 Firmly push the 1/4" Plastic Tubing into the end of the threaded Faucet Stem. Hand-tighten the plastic Compression Nut onto the

threads. Tighten with an adjustable wrench approximately 1/2 turn.

NOTE: Do not bend or crimp 1/4" Plastic Tubing when inserting. Do not over tighten the Compression Nut.

FAUCET FOR

FILTERED WATER

1/4" PLASTIC TUBING

INLET OUTLET

HOT WATER

ALVE

1/4" PLASTIC TUBING

COLD WATER

ALVE

5/8"

V4.0

WFQT13000 & WFQT13500 Series

STEP 7

Install the QuickTwist™Filter

1 Hold the QuickTwist

™

Filter B with the label facing to the left slightly. The two nozzles on top of the QuickTwist™Filter should be

toward the back of the QuickTwist

™

Filter. If holding properly, the two extended flanges on top of the QuickTwist™Filter should be

out to each side. See Figure 6

1 at right.

2 Lift the QuickTwist

™

Filter straight up into the System Head A until the two nozzles seat into the ports and the two extended flanges

on top of the QuickTwist

™

Filter are fully engaged into the System Head.

3 Turn the QuickTwist

™

Filter counter-clockwise until it stops.

STEP 8

Test the Filter System for Proper Operation

1 Turn on the cold water shut-off valve under the sink.

2 Turn on the new Faucet for Filtered Water D. In order for the Filter System to flush out any air and carbon fines (fine black powder)

from the QuickTwist

™

Filter, allow the water to run for approximately 10 minutes.

3 Check for any leaks between the System Head assembly and Filter; around all fittings; on Kitchen Faucet Adapter H connection;

and on faucet/tubing connection.

If there are leaks between the System Head assembly and the QuickTwist

™

Filter:

n Turn off the cold water shut-off valve to the Filter System and turn on the Faucet for Filtered Water to drain the water and

release pressure.

n Remove the QuickTwist

™

Filter and inspect the O-Rings around the nozzles on top of it. Make sure they are in place and free

from dirt and particles.

n Turn off the Faucet for Filtered Water. n Replace the QuickTwist

™

Filter by lifting it straight up into the System Head until the two nozzles seat into the ports and the

two extended flanges on top of the QuickTwist

™

Filter are fully engaged into the System Head. Turn the QuickTwist™Filter

counter-clockwise until it stops.

n Turn the cold water supply valve back on and turn on the Faucet for Filtered Water.

If there are leaks around the fittings:

n Turn off the cold water shut-off valve to the Filter System to release pressure in the System. n While pulling the 1/4" Plastic Tubing

L with one hand, press in on the grey collar around the inlet and/or outlet fitting. Check

to make sure that the 1/4" Plastic Tubing is cut squarely and that it is not scratched. If the 1/4" Plastic Tubing is unevenly cut or scratched, cut off 1/2" to 5/8" and re-install the Plastic Tubing (see Step 5 of Installation Instructions).

n Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.

continued to next page

FLEXIBLE HOSE INSTALLATION

HOT WATER

VALVE

COLD WATER

VALVE

KITCHEN FAUCET

FAUCET FOR

FILTERED WATER

V4.0

WFQT13000 & WFQT13500 Series

STEP 8

Test the Filter System for Proper Operation (continued)

If there are leaks on the Kitchen Faucet Adapter connection:

n Turn off the cold water shut-off valve to the Filter System to release pressure in the System. n Locate the Kitchen Faucet Adapter.

• If the 1/4" Plastic Tubing is leaking, follow the previous steps (“If there are leaks around the fittings”).

• If the thread between the Kitchen Faucet Adapter and the kitchen faucet stem is leaking, tighten more securely. If leaking continues, disconnect the 1/4" Plastic Tubing and remove the Kitchen Faucet Adapter. Wrap the Kitchen Faucet Adapter and the threaded faucet stem with plumber’s tape and re-install (see Step 2 of Installation Instructions).

• If the thread between the Kitchen Faucet Adapter and the cold water supply line is leaking, tighten more securely. If leaking continues, disconnect the 1/4" Plastic Tubing and remove the Kitchen Faucet Adapter. Wrap the Kitchen Faucet Adapter and the cold water supply line with plumber’s tape and re-install (see Step 2 of Installation Instructions).

n Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.

If there are leaks on the Faucet for Filtered Water/1/4" Plastic Tubing connection:

n Turn off the cold water shut-off valve to the Filter System to release pressure in the System. n Loosen and remove the Compression Nut

K on the Faucet for Filtered Water Stem. Check the 1/4" Plastic Tubing to see if it is

cut squarely. Make sure the 1/4" Plastic Tubing is placed firmly into the end of the Faucet Stem; retighten the Compression Nut securely by hand; then tighten 1/2 turn with an adjustable wrench. If leaking continues, remove the Compression Nut and apply plumber’s tape to the Faucet for Filtered Water Stem and re-install the Compression Nut.

n Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.

‰ If leaks continue, turn off the water supply and call Customer Service or your local plumber. ‰ For Filter Replacement Instructions please see below

QuickTwist

™

Filter Replacement

1 Turn off the cold water shut-off valve to the Filter System A.

2 Turn the QuickTwist

™

Filter B clockwise until it releases. Gently pull down on the used QuickTwist™Filter to remove it from the

System Head. Discard the used QuickTwist

™

Filter.

NOTE: Place a pan or bucket under the Filter System to catch any water drips.

3 Hold the new QuickTwist

™

Filter with the label facing to the left slightly. The two nozzles on top of the QuickTwist™Filter should

be toward the back of the QuickTwist

™

Filter. If holding properly, the two extended flanges on top of the QuickTwist™Filter should

be out to each side.

4 Lift the QuickTwist

™

Filter straight up into the System Head until the two nozzles seat into the ports and the two extended

flanges on top of the QuickTwist

™

Filter are fully engaged into the System Head.

5 Turn the QuickTwist

™

Filter counter-clockwise until it stops.

6 Turn on the cold water shut-off valve and the Faucet for Filtered Water D and check for any leaks. If there are leaks, refer to the

troubleshooting information in Step 7 of the Installation Instructions.

7 Flush water through the Faucet for Filtered Water for approximately 10 minutes to flush out any air and carbon fines

(fine black powder) from the QuickTwist

™

Filter. Check for leaks once more before completion.

V4.0

WFQT13000 & WFQT13500 Series

+ 19 hidden pages

Du Pont WFQT13000 Series, WFQT13500 Series Installation Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual