Duluth Forge FDI32R Owner's Operation And Installation Manual

Page 1
VENT-FREE GAS
FIREPLACE INSERT
OWNER’S OPERATION AND
INSTALLATION MANUAL
MODEL FDI32R
US
WARNING: If the information in this manual is not
followed exactly, a re or explosion may result causing property damage, personal injury or loss of life.
— Do not store or use gasoline or other ammable va-
pors and liquids in the vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re department.
Installation and service must be performed by a quali­ed installer, service agency or the gas supplier.
WARNING: This appliance is equipped for Natural and
Propane gas. Field conversion is not permitted other than between natural or propane gases.
Visit us online at www.FACTORYBUYSDIRECT.com
for a list of mantels used with this product.
Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 1-855-607-6557, 8:00 am - 4:30 pm EST,
Monday through Friday or email info@factorybuysdirect.com
Page 2
www.factorybuysdirect.com
200245-01A
2
TABLE OF CONTENTS
Safety ........................................................ 3
Specications ............................................ 4
Qualied Installing Agency ........................ 5
Product Features ....................................... 5
Local Codes............................................... 5
Unpacking.................................................. 6
Product Identication ................................. 6
Water Vapor: A By-Product Of
Unvented Room Heaters ....................... 6
Air For Combustion and Ventilation ........... 7
Installation ................................................. 9
Operation ................................................. 20
Inspecting Burners................................... 24
Care And Maintenance ............................ 25
Troubleshooting ....................................... 26
Replacement Parts .................................. 29
Parts ........................................................ 30
Service Hints ........................................... 31
Technical Service..................................... 31
Warranty .................................................. 32
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This is an unvented gas-red heater. It uses air (oxygen) from the room in which it is installed. Provisions for ad­equate combustion and ventilation air must be provided.
Refer to Air For Combustion and Ventilation section on
page 7 of this manual.
WARNING: Improper installation, adjustment, al-
teration, service or maintenance can cause injury or property damage. Refer to this manual for correct in­stallation and operational procedures. For assistance or additional information consult a qualied installer, service agency or the gas supplier.
This appliance may be installed in an aftermarket,* per­manently located, manufactured (mobile) home, where not prohibited by local codes.
This appliance is only for use with propane or natural gas. Field conversion by any other means including the use of a kit is not permitted.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
SAVE THIS BOOK
PATENT INFORMATION
This product may be covered by one or more of the following United States patents:
8,915,239 8,851,065 8,764,436 8,757,202 8,757,139 8,752,541 8,568,136 8,545,216 8,517,718 8,516,878 8,506,290 8,465,277 8,317,511 8,297,968 8,281,781 8,241,034 8,235,708 8,152,515 8,011,920 7,967,006 7,967,007
7,654,820 7,730,765 7,677,236 7,607,426 7,434,447
Page 3
www.factorybuysdirect.com
3
200245-01A
SAFETY
IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, op­erate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock and carbon monoxide poisoning. Failure
to follow these instructions will
void the warranty.
Only a qualied installer, service agent, or local gas supplier may install and service this product.
WARNING: Keep the appli-
ance area clear and free from
combustible materials, gasoline, and other ammable vapors and liquids.
WARNING: This appliance can be used with propane or natural gas. It is shipped from the factory adjusted for use with propane.
DANGER: Carbon monoxide poisoning may lead to death!
CARBON MONOXIDE POISONING: Early
signs of carbon monoxide poisoning resemble the u, with headaches, dizziness or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more af­fected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the inu­ence of alcohol and those at high altitudes.
NATURAL AND PROPANE/LP GAS: Natural
and Propane/LP gas are odorless. An odor­making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.
WARNING: Any change to
this replace or its controls can be dangerous.
WARNING: Do not allow fans
to blow directly into replace. Avoid any drafts that alter burner ame patterns.
WARNING: Do not use a
blower insert, heat exchange
insert or other accessory not
approved for use with this heater.
WARNING: Due to high tem-
peratures, the appliance should be located out of trafc and away from furniture and draperies.
WARNING: Do not place
clothing or other ammable ma­terial on or near the appliance. Never place any objects in the replace.
WARNING: Fireplace be-
comes very hot when running. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Fireplace
will remain hot for a time after
shutdown. Allow surfaces to cool before touching.
WARNING: Carefully super-
vise young children when they are in the room with the heater.
WARNING: You must oper-
ate this replace with screen in place.
Page 4
www.factorybuysdirect.com
200245-01A
4
1. Do not place Propane/LP supply tank(s) inside any structure. Propane/LP supply tank(s) must be placed outdoors.
2. This heater shall not be installed in a bedroom or bathroom.
3. This heater needs fresh air ventilation to run properly. This heater has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available. See Air for Combustion and Ventilation, pages 7 and 8. If heater keeps shutting off, see Troubleshooting, page 26.
4. Keep all air openings in front and bottom of heater clear and free of debris. This will ensure enough air for proper combustion.
5. If heater shuts off, do not relight until you have provided fresh, outside air. If heater keeps shutting off, have it serviced.
6. Do not run heater:
• Where ammable liquids or vapors are
used or stored.
• Under dusty conditions.
7. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these prod­ucts may create a white powder residue within burner box or on adjacent walls or furniture.
8. Always run heater with control knob at PILOT or ON locked positions. Never set control knob between locked positions. Poor combustion and higher levels of carbon monoxide may result.
SAFETY
9. Do not use heater if any part has been under water. Immediately call a qualied service technician to inspect the room heater and to replace any part of the control system and any gas control which has been under water.
10. Turn off and unplug heater and let cool before servicing. Only a qualied service person should service and repair heater.
11. Operating heater above elevations of 4,500 feet could cause pilot outage.
12. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.
13. Do not use this heater as a wood-burning heater. Use only the logs provided with the heater.
14. To prevent sooting, follow the instructions in Care and Maintenance (see page 25).
15. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause soot­ing. Do not add lava rock around base. Rock and debris could fall into the control area of heater. After servicing, always replace screen before operating heater.
16. This heater is designed to be smokeless. If logs ever appear to smoke, turn off heater and call a qualied service person.
Note: During initial operation, slight smok-
ing could occur due to log curing and the heater burning manufacturing residues.
SPECIFICATIONS
Model FDI32R
Gas Type Natural Gas Propane Gas
Ignition Piezo Ignitor Piezo Ignitor
Input Rating
32,000 Btu/Hr 32,000 Btu/Hr
Pressure Regulator Setting 4" W.C. 9" W.C.
Inlet Gas Pressure* (inches of water)
(*for purposes of input adjustment)
Maximum 9" Maximum 14"
Minimum 5" Minimum 11"
Heater Dimensions (HxWxD) •
33.27" × 36.38" × 18.38"
Carton Dimensions (HxWxD) •
35.85" × 40.19" × 20.49"
Stove Weight • 88.2 lbs
Shipping Weight • 98.5 lbs
Page 5
www.factorybuysdirect.com
5
200245-01A
QUALIFIED INSTALLING AGENCY
Only a qualied agency should install and replace gas piping, gas utilization equipment or accessories, and repair and equipment ser­vicing. The term “qualied agency” means any individual, rm, corporation, or company that either in person or through a representative is engaged in and is responsible for:
a) Installing, testing, or replacing gas piping
or
b) Connecting, installing, testing, repairing,
or servicing equipment; that is experienced in such work; that is familiar with all precau­tions required; and that has complied with all the requirement of the authority having jurisdiction.
PRODUCT FEATURES
SAFETY PILOT
This heater has a pilot with an Oxygen Deple­tion Sensing (ODS) safety shutoff system. The ODS/pilot shuts off the heater if there is not enough fresh air.
PIEZO IGNITION SYSTEM
This heater is equipped with an electronic piezo control system. This system requires one AAA battery (provided).
2 GAS OPTIONS AVAILABLE
Your heater is equipped to operate on either Propane/LP or Natural gas. The heater is shipped from the factory ready for connect­ing to Propane/LP. The heater can easily be changed to Natural gas by having your quali­ed installer follow the instructions on page 10 and the markings on the heater.
LOCAL CODES
Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code, ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
1 Batterymarch Park
Quincy, MA 02269-9101
This heater is designed for vent-free op­eration. State and local codes in some areas prohibit the use of vent-free heaters.
State of Massachusetts: The installation must be made by a licensed plumber or gas tter in the Commonwealth of Mas­sachusetts.
Sellers of unvented propane or natural gas-red supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.
In the State of Massachusetts the gas cock must be a T-handle type. The State of Massachusetts requires that a exible appliance connector cannot exceed three feet in length.
Page 6
www.factorybuysdirect.com
200245-01A
6
PRODUCT IDENTIFICATION
Figure 1 - Vent-Free Fireplace Insert
WATER VAPOR: A BY-PRODUCT OF
UNVENTED ROOM HEATERS
Water vapor is a by-product of gas combus­tion. An unvented room heater produces ap­proximately one (1) ounce (30 mL) of water for every 1,000 BTUs (0.3 KWs) of gas input per hour. Unvented room heaters are recom­mended as supplemental heat (a room) rather than a primary heat source (an entire house). In most supplemental heat applications, the water vapor does not create a problem. In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather.
The following steps will help ensure that water vapor does not become a problem.
1. Be sure the heater is sized properly for the application, including ample combustion air and circulation air.
2. If high humidity is experienced, a dehu­midier may be used to help lower the water vapor content of the air.
3. Do not use an unvented room heater as the primary heat source.
UNPACKING
1. Remove top inner pack.
2. Tilt carton so that heater is upright.
3. Remove protective side packaging.
4. Slide heater out of carton. 5 Remove protective plastic wrap.
6. Hold the screen, lift, and pull forward.
7. Remove log set by cutting plastic ties.
8. Carefully unwrap log.
9. Check for any shipping damage. If heater or log is damaged, promptly inform your dealer where you bought the heater.
Hood
Screen
Heater Controls (Behind Panel)
Page 7
www.factorybuysdirect.com
7
200245-01A
AIR FOR COMBUSTION AND VENTILATION
WARNING: This heater shall
not be installed in a conned space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home.
Today’s homes are built more energy efcient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible. While it is good to make your home energy efcient, your home needs to breathe. Fresh air must enter your home. All fuel-burning ap­pliances need fresh air for proper combustion and ventilation. Exhaust fans, replaces, clothes dryers and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.
WARNING: This heater shall
not be installed in a room or space unless the required vol­ume of indoor combustion air is provided by the method de­scribed in the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code, or
applicable local codes.
WARNING: If the area in which
the heater may be operated does not meet the required volume for indoor combustion air, combus­tion and ventilation air shall be provided by one of the methods described in the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code,
or applicable local codes.
Page 8
www.factorybuysdirect.com
200245-01A
8
VENTILATION AIR
Ventilation Air From Inside Building
AIR FOR COMBUSTION AND VENTILATION
Outlet Air
Ventilated Attic
Outlet Air
Inlet Air
Inlet Air
Ventilated
Crawl Space
To
Crawl
Space
To Attic
Figure 2 - Ventilation Air from Inside
Building
Figure 3 - Ventilation Air from Outdoors
This fresh air would come from an adjoining unconned space. When ventilating to an adjoining unconned space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the oor on the wall connecting the two spaces (see options
1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, Air for Combustion and Ventilation for required size of ventilation
grills or ducts.
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts. You must provide two perma­nent openings: one within 12" of the ceiling and one within 12" of the oor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation for required size
of ventilation grills or ducts.
IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent. Rework worksheet, adding the space of the adjoining unconned space. The combined spaces must have enough fresh air to supply all appliances in both spaces.
Or
Remove Door into Adjoining
Room,
Option 3
Ventilation Grills
Into Adjoining Room,
Option 2
12"
12"
Ventilation
Grills into Adjoining
Room,
Option 1
Page 9
www.factorybuysdirect.com
9
200245-01A
INSTALLATION
NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your pri­mary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.
WARNING: A qualied ser-
vice person must install heater. Follow all local codes.
WARNING: Never install the
heater
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture,
clothing, or other ammable objects are less than 42" from the front, top, or sides of the
heater
• in high trafc areas
• in windy or drafty areas
CAUTION: This heater cre-
ates warm air currents. These currents move heat to wall sur­faces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as to­bacco smoke, aromatic candles, cleaning uids, oil or kerosene lamps, etc.) in the air exist, may cause walls to discolor.
Figure 4 - Minimum Clearances to Wall
and Ceiling
IMPORTANT: Vent-free heaters add moisture to the air. Although this is benecial, installing heater in rooms without enough ventilation air may cause mildew to form too much moisture. See Air for Combustion and Ventilation, pages 7 and 8.
CHECK GAS TYPE
Be sure your gas supply is right for your heat­er. Otherwise, call dealer where you bought the heater for proper type heater.
CLEARANCES TO
COMBUSTIBLES
WARNING: You must main-
tain the minimum clearances
shown in Figure 4. If you can, provide greater clearances from oor, ceiling, and joining wall. Measure from outermost point of heater.
Minimum Wall and Ceiling
Clearances
A. Clearances from outermost point of heater
to any combustible side wall should not be less than 7".
B. Clearances from the heater to the ceiling
should not be less than 42".
Note: When heater is installed directly on carpeting, vinyl or other combustible material,
other than wood ooring, the heater must be
installed on a metal or wood panel extending the full width and depth of the heater.
Ceiling
7"
Min.
7"
Min.
42"
Min.
Side Wall
Side Wall
Front View
Page 10
www.factorybuysdirect.com
200245-01A
10
INSTALLATION
Figure 5 - Supplied Fitting
Yellow Natural Gas Plunger Underneath Metal Cap
Blue Propane/LP Gas Plunger Underneath Dust Cover
Figure 6 - Gas Regulator
Insert Gas Fitting for Natural Gas
Insert Gas Fitting for Propane/LP Gas
GAS SELECTION
This appliance is factory preset for propane/LP gas. No changes are required for connecting to propane/LP.
Only a qualied installer or service technician can perform gas selec­tion and connecting to gas supply.
CAUTION: Two gas line in-
stallations at the same time are
prohibited.
CAUTION: To avoid gas leak-
age for the gas not being used at the inlet of regulator, a qualied installer or service technician must use supplied cap.
You will notice a color coded
plunger on the inside of the regu­lator. This is normal. When the in­let connection tting is inserted and tightened, this plunger will be pushed back by the tting making all of the adjustments for the gas being supplied. DO NOT REMOVE THE PLUNGER. The regulator will not work.
The inlet regulator is color coded for identication of the correct gas type. Blue is for propane (LP gas) and yellow is for natural gas.
Fitting supplied with the product located in
the hardware bag. Fitting part number:
160960-02 (straight)
160960-03 (elbow)
Blue Dust
Cover
DO NOT REMOVE
Blue Propane/LP Plunger
Install Gas Fitting Here
FOR PROPANE/LP GAS
INSTALLATION: BLUE
1. Remove blue dust cover.
Page 11
www.factorybuysdirect.com
11
200245-01A
INSTALLATION
DO NOT use an off the shelf 3/8" NPT pipe plug. This will damage the plungers located inside the regulator.
DO NOT try to remove the plung­ers from inside the regulator. The plunger will be pushed back as the tting is installed.
Make sure the type of gas being used is correct. Check to make sure the connection tting is in the correct inlet on the regula­tor. Refer to Connecting to Gas Supply, page 14.
If you are using natural gas and the pilot will not light, see Troubleshooting, page 26.
Use only the cap supplied on the regulator. Do not use an off the shelf pipe plug. This can damage the plunger. The supplied regula­tor cap is designed so it will not engage the unused gas type.
4. Apply thread sealant to the threads on the connection tting. While pushing in, rotate the tting clockwise until the threads engage the regulator. After the tting has been hand tightened into the regulator use a wrench to complete tightening of the tting. Install additional tting to connect to the house supply.
Metal Cap
Metal Cap
DO NOT REMOVE
Yellow Natural Gas Plunger
Install Gas Fitting Here
2. Apply thread sealant to the threads on the connection tting. While pushing in, rotate the tting clockwise until the threads engage the regulator. After the tting has been hand tightened into the regulator use a wrench to complete tightening of the tting. Install additional tting to connect to the house supply.
FOR NATURAL GAS (NG)
INSTALLATION: YELLOW
1. Remove the blue dust cover from the regulator.
2. Remove the metal cap installed over the NG regulator inlet.
3. Install metal cap over LP/Propane regulator inlet. This will keep debris out of regulator.
Back of Fireplace
Page 12
www.factorybuysdirect.com
200245-01A
12
INSTALLATION
BUILT-IN FIREPLACE INSTALLATION
Figure 9 - Rough Opening for Wall
Installation
Figure 7 - Clearance to Combustibles
Figure 8 - Fireplace Clearances
3/4" Clearance to Facia
Note: Height of fireplace opening on facia to be 30 1/2"
1 3/8" Clearance to Sides, Back and Top
36 1/2" 37
3
/4"
WARNING: Do not allow any
combustible materials to overlap the rebox front.
WARNING: Do not allow
combustible or noncombustible materials to cover any necessary openings like louvered slots.
WARNING: Never modify or cover the louvered slots on the front of the rebox.
Built-in installation of this replace involves installing replace into a framed-in enclosure. This makes the front of the replace ush with wall. If installing a built-in mantel above the replace, you must follow the clearances shown in Figure 7.
NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above the replace may become hot to the touch. If installed properly, these temperatures meet the require­ment of the national product standard. Follow all minimum
clearances shown in this manual
(see Figure 7).
1. Frame in rough opening. Use dimensions shown in Figure 8 for the rough opening. If installing in a corner, use dimensions shown in Figure 10 (page 13) for the rough opening. The height is 23 1/4", which is the same as the wall opening above.
2. Carefully set replace in front of rough opening with back of replace inside wall opening.
Bottom Edge of Vent Hood
2
1
/2"
2"
4"
7"
8"
10"
12"
Note: All vertical measurements are from lower edge of vent hood to bottom of mantel shelf.
42" to
Ceiling
Safe
Zone
Mantel
Shelf
14"
16"
18"
35"
32
1
/
2
"
19"
Page 13
www.factorybuysdirect.com
13
200245-01A
INSTALLATION
3. Attach gas line to replace gas regulator. See Connecting to Gas Supply, page 14.
4. Check all gas connections for leaks. See Checking Gas Connections, page 16.
IMPORTANT: When nishing your rebox,
combustible materials such as wall board, gypsum board, sheet rock, drywall, plywood, etc, must have 1/2" clearance to the sides
and top of the rebox. Combustible materials should never overlap the rebox front.
Figure 10 - Rough Opening for Corner
Installation
CAUTION: Do not operate
replace without hood in place.
1. Align 3 holes in upper side of hood with holes in heat insulation board (see Fig­ure 11).
2. Insert screwdriver through hole in top re­box panel to secure hood to heat insulation board with 3 screws (see Figure 11).
INSTALLING HOOD
35"
28
1
/
8
"
39
3
/
4
"
56 1/4"
Figure 11 - Hood Installation
Hood
Heat Insulation Board
Top of Firebox
Top Firebox Panel
Page 14
www.factorybuysdirect.com
200245-01A
14
INSTALLATION
CONNECTING TO GAS SUPPLY
CAUTION: For propane/
LP gas, never connect heater directly to the gas supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and gas supply. Gas supplier provides external regu­lator for natural gas. The installer provides the external regulator for propane/LP gas.
CAUTION: Use pipe joint
sealant that is resistant to gas (Propane/LP or Natural Gas).
Before installing heater, make sure you have the items listed below:
• external regulator for propane/LP unit only (supplied by installer)
• piping (check local codes)
• sealant (resistant to natural gas and pro­pane/LP gas)
• equipment shutoff valve*
• test gauge connection*
• sediment trap
• tee joint
• pipe wrench
• exible gas hose (check local codes)
* A CSA design-certied equipment shutoff valve with 1/8" NPT tap is an acceptable al­ternative to test gauge connection. Purchase the optional CSA design certied equipment shutoff valve from your dealer.
Typical Inlet Pipe Diameters
Use 3/8" black iron pipe or greater. Installa­tion must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 12, page 15).
IMPORTANT: Install an equipment shutoff valve in an accessible location. The equip­ment shutoff valve is for turning on or shutting off the gas to the appliance.
WARNING: A qualied ser-
vice technician must connect heater to gas supply. Follow all local codes.
WARNING: This appliance
requires a 3/8" NPT (National Pipe Thread) inlet connection to the pressure regulator.
WARNING: For natural gas,
Never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead
gas.
WARNING: Do not over-
tighten gas connections.
CAUTION: Use only new,
black iron or steel pipe. Inter­nally tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of pressure will occur.
CAUTION: For natural gas,
check your gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 9" of water. If gas line pressure is higher, heater
regulator damage could occur.
CAUTION: Avoid damage to
regulator. Hold gas regulator with wrench when connecting
into gas piping and/or ttings.
Page 15
www.factorybuysdirect.com
15
200245-01A
Figure 12 - Gas Connection
* Purchase the optional CSA design-certied equipment shutoff valve from your dealer.
Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.
For propane/LP installations, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11" and 14" of water. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down
Figure 13 - External Regulator
with Vent Pointing Down
Figure 14 - Gas Regulator Location and Gas Line Access into Fireplace Cabinet
External Regulator with Vent Pointing Down
Propane/LP Supply Tank
Equipment Shutoff Valve
Ground Joint Union
3/8" NPT
Pipe Nipple
Tee Joint
Reducer Bushing to 1/8" NPT
1/8" NPT Plug Tap
Test Gauge Connection*
Sediment
Trap
Tee Joint
Pipe Nipple
Gap
3" Minimum
as shown in Figure 13. Pointing the vent down protects it from freezing rain or sleet.
For both gas types, install sediment trap in supply line as shown in Figure 12. Place sediment trap where it is within reach for cleaning. Place sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sedi­ment trap is not installed or is installed wrong, heater may not run properly.
Natural Gas
From Gas Meter (5" W.C.** to 9" W.C. Pressure)
Propane/LP
From External Regulator (11" W.C.** to 14" W.C. Pressure)
INSTALLATION
Gas Regulator Inlet Connector
Page 16
www.factorybuysdirect.com
200245-01A
16
Figure 15 - Equipment Shutoff Valve
CHECKING GAS CONNECTIONS
Open
Closed
Equipment Shutoff Valve
Figure 17 - Checking Gas Joints for
Natural Gas
INSTALLATION
WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once.
WARNING: Never use an open ame to check for a leak. Apply a noncorrosive leak detection uid to all joints. If bubbles form, there is a leak. Correct all leaks at once.
PRESSURE TESTING GAS SUPPLY
PIPING SYSTEM
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
1. Disconnect heater with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping sys­tem. Pressures in excess of 1/2 PSIG will damage heater regulator.
2. Cap off open end of gas pipe where equip­ment shutoff valve was connected.
3. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.
4. Check all joints of gas supply piping sys­tem. Apply noncorrosive leak detection uid to all joints. If bubbles form, there may be a leak.
5. Correct all leaks at once.
6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected ttings for leaks.
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see Fig­ure 15).
2. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.
3. Check all joints from gas meter to equip­ment shutoff valve for natural gas or propane/LP supply to equipment shutoff valve for propane/LP (see Figure 16 or
17). Apply a noncorrosive leak detection uid to all joints. Bubbles forming show a leak.
4. Correct all leaks at once.
PRESSURE TESTING HEATER GAS
CONNECTIONS
1. Open equipment shutoff valve (see Fig­ure 15).
2. Open main gas valve located on or near gas meter for natural gas or open pro­pane/LP supply tank valve.
3. Make sure control knob of heater is in the OFF position.
Control Valve Location
Control Valve Location
Equipment Shutoff Valve
Equipment Shutoff Valve
External Regulator with Vent Pointing Down
Propane/LP Supply Tank
Figure 16 - Checking Gas Joints for
Propane/LP Gas
Gas Meter
2. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.
3. Check all joints from gas meter to equip­ment shutoff valve for natural gas or propane/LP supply to equipment shutoff valve for propane/LP (see Figure 16 or
17). Apply a noncorrosive leak detection uid to all joints. Bubbles forming show a leak.
4. Correct all leaks at once.
PRESSURE TESTING HEATER GAS
CONNECTIONS
1. Open equipment shutoff valve (see Fig­ure 15).
2. Open main gas valve located on or near gas meter for natural gas or open pro­pane/LP supply tank valve.
3. Make sure control knob of heater is in the OFF position.
Page 17
www.factorybuysdirect.com
17
200245-01A
Top Trim Piece
Left Trim Piece
Right Trim Piece
Figure 18 - Decorative Trim
Figure 19 - Installing Decorative Trim
INSTALLATION
4. Check all joints from equipment shutoff valve to control valve (see Figure 16 or 17, page 16). Apply a noncorrosive leak detection uid to all joints. Bubbles form­ing show a leak.
5. Correct all leaks at once.
INSTALLATION FOR DECORATIVE TRIM
6. Light heater (see Lighting Instructions on page 20). Check all other internal joints for leaks.
7. Turn off heater (see To Turn Off Gas Ap- pliance, page 21).
1. Identify left, right and top decorative trim pieces (see Figure 18).
2. Slide slots in 3 trim pieces over screws on the replace (see Figure 19).
Screw
Top Decorative Trim
Left/Right
Decorative Trim
Page 18
www.factorybuysdirect.com
200245-01A
18
Figure 21 - Installing Logs
INSTALLATION
INSTALLING LOGS
WARNING: Failure to posi-
tion the parts in accordance with these diagrams or failure to use only parts specically approved with this heater may result in property damage or personal injury.
CAUTION: After installation, and periodically thereafter, check to ensure that no ame comes in contact with any log. With the heater set to high, check to see if ames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contact­ing logs will create soot.
Each log is marked with a number. This number will help you to identify the logs when installing.
After installing logs, add decorative cinders around the grate base, do not place any decorative cinders on logs or burner.
IMPORTANT: Make sure logs do not cover any burner ports. It is very important to install the logs exactly as instructed. Do not modify logs. Use only logs supplied with heater.
Logs 1 through 6 have pins on the back that slide into the slots in the base brackets.
Some logs may have pins that t into holes on another log. This helps keep them in place.
Slot in Bracket
Rear Bracket
Middle Bracket
Front Bracket
Figure 20 - Log Base
8
2
3
4
5
6
7
9
1
Page 19
www.factorybuysdirect.com
19
200245-01A
INSTALLATION
INSTALLING BATTERIES
CAUTION: Do not mix old and new batteries. Do not mix alka­line, standard (carbon - zinc), or rechargeable (nickel - cadmium) batteries. Do not dispose of batteries in re, batteries may explode or leak.
• Batteries are included.
• Remove batteries when depleted.
• Install/replace the batteries according to the type and quantity stated in table below.
• Be sure to observe proper polarity (+/-) when installing or replacing the batteries. Damage due to improper battery installation may void the warranty on the product.
• For remote control systems, maximize bat­tery life by turning off the receiver when it is not in use.
• For long periods of non-operation, remove batteries from all components for safety.
Component Type of Battery Qty.
Ignitor AAA 1
Remote Control AAA 2 or 3*
Remote Receiver AA 4
*Note: Quantity depends on model of remote
Control.
Ignitor
Unscrew ignitor cap and install a AAA battery with the + pointing out. Replace cap.
Receiver and Remote Control
Batteries are required in both the Remote Control (Transmitter) (2 AAA size) and Re­ceiver (4 AA size) (see Figure 23).
Note: Be sure batteries are placed correctly. Reversing the batteries can cause damage to the receiver and remote. Replace all batteries on a yearly basis or sooner.
Position the slide switch on the front of the receiver box in the ON position before install­ing batteries. Once the batteries are installed you will hear a single beep which indicates the batteries are charged. If you do not hear a beep, replace with new batteries.
Figure 22 - Installing Battery in Ignitor
AAA
Battery
Positive
UP
AA
AA
AA
AAA
AAA
AA
REMOTE
OFF
ON
LEARN
Figure 23 - Installing Batteries in Remote
Control and Receiver
Receiver
Remote Control (Transmitter)
Page 20
www.factorybuysdirect.com
200245-01A
20
OPERATION
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
re or explosion may result caus­ing property damage, personal injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around
the appliance area for gas. Be sure to smell next to the oor because some gas is heavier than air and will settle on the oor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualied service technician. Force or attempted repair may result in a re or explosion.
D. Do not use this appliance if any part
has been under water. Immediately call a qualied service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.
WARNING: You must oper-
ate this heater with the screen
in place. Make sure screen is installed before running heater.
NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange ame will also be pres­ent. Open damper or window to vent smell. This will only last a few hours.
1. STOP! Read the safety information above.
2. Make sure equipment shutoff valve is fully open.
3. Push in the control knob slightly and turn clockwise to the OFF position.
4. Wait ve (5) minutes to clear out any gas. Then smell for gas around heater and near the oor. If you smell gas, STOP! Follow "B" in the safety information above. If you do not smell gas, go to the next step.
5. Push in the control knob slightly and turn counterclockwise to the PILOT position. Press in control knob for ve (5) seconds (see Figure 24).
Note: The rst time that the heater is oper-
ated after connecting the gas supply,the control knob should be pressed for about thirty (30) seconds. This will allow air to bleed from the gas system. If pilot does not stay lit, refer to Troubleshooting, pages 26
though 29. Also contact a qualied service
technician or gas supplier for repairs. Until repairs are made, light pilot with match.
• If control knob does not pop up when released, contact a qualified service technician or gas supplier for repairs.
LIGHTING INSTRUCTIONS
Figure 24 - Control Knob in the OFF
Position
Ignitor Button
Receiver
Control Knob
Page 21
www.factorybuysdirect.com
21
200245-01A
9. Turn control knob counterclockwise to the ON position. The main burner should light.
10. Make sure the heater screen is in place before operating heater.
11. If heater will not operate, follow the instruc­tions To Turn Off Gas To Appliance, and call your service technical or gas supplier.
CAUTION: Do not try to ad-
just heating levels by using the equipment shutoff valve.
WARNING: If input gas type is NG, make sure NG pilot burner ignites. If input gas type is LP, make sure LP pilot burner ignites (see Figure 35, page 26).
6. With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the burner. If needed, keep press­ing ignitor button until pilot lights.
Note: If pilot does not stay lit, refer to Troubleshooting, pages 26 though 29.
Also contact a qualied service technician
or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.
7. Keep control knob pressed in for 30 sec­onds after lighting pilot. After 30 seconds, release control knob.
Note: If pilot goes out, repeat steps 4
through 8. This heater has a safety inter­lock system. Wait one (1) minute before lighting pilot again.
8. Be sure the slide switch on the front of the receiver is in the ON position.
OPERATION
Shutting Off Heater
Turn control knob clockwise to the OFF position.
Shutting Off Burner Only (pilot
stays lit )
Turn control knob clockwise to the PILOT position.
1. Remove screen by lifting and pulling forward.
2. Follow steps 1 through 6 under Lighting Instructions, page 20.
3. With control knob in PILOT position, strike match, and hold near pilot. Press in control knob; pilot should light.
4. Keep control knob pressed in for 30 sec­onds after lighting pilot. After 30 seconds, release control knob.
5. Make sure the heater screen is in place before operating heater.
TO TURN OFF GAS TO APPLIANCE
MANUAL LIGHTING PROCEDURE
Page 22
www.factorybuysdirect.com
200245-01A
22
Key Settings
ON - Operates unit to on position, manually operated solenoid ON.
OFF - Operates unit to off position, manually operated solenoid OFF.
MODE - Changes unit from manual mode to thermo mode.
SET - Sets temperature in thermo mode.
TEMP
ROOM SET TEMP
1
4
6
2
3 5
Figure 26 - Remote Control
Figure 27 - Remote Control Display
LCD Liquid Crystal Display
1. DISPLAY Indicates CURRENT room temperature.
2. °F or °C Indicates degrees Fahrenheit or Celsius.
3. FLAME Indicates burner/valve in operation.
4. ROOM Indicates remote is in THERMO
operation.
5. TEMP Appears during manual operation.
6. SET Appears during time the of setting
the desired temperature in the thermo operation.
OPERATION
LEARN
REMOTE OFF
ON
Figure 25 - Receiver
Slide Switch
Learn Button
REMOTE CONTROL SYSTEM
Programming the Remote and Receiver
The remote and receiver must be “learned” to one another.
To prepare the receiver box for learning, use a pen or small screwdriver to gently press and hold the learn button until you hear 3 series of beeps.
1. Place the slide switch on the receiver in the remote position (see Figure 21).
2. Turn control knob on the heater to the ON position.
3. Use a pen or small screwdriver to gently press and hold the recessed LEARN button on the face of the receiver for 2-3 seconds. You will hear a beep.
4. Press the ON button on the remote control to light the burner (see Figure 21). You will hear a series of beeps. This will also "learn", or program, the remote and the receiver.
Note: Remote must be at least 5 feet
away from the receiver during the learning process.
Note: If the remote control is lost or dam-
aged, the slide switch on the receiver can be used to operate the heater.
Note: When batteries are replaced the
learning process above must be repeated.
Remote Control Operation
This appliance must not be used with glass doors in the closed position. This can lead to pilot outages and severe sooting outside the replace.
The transmitter operates on 2 AAA batteries.
Page 23
www.factorybuysdirect.com
23
200245-01A
OPERATION
2. Press and hold the SET key until the de­sired set temperature is reached. The LCD screen set numbers will increase from 45° to 99° and then restart over at 45°.
3. Release the SET key. The LCD screen will display the set temperature for 3 sec­onds, then ash the set temperature for 3 seconds, then LCD screen will default to display the room temperature.
To Change The Set Temperature
1. Press and hold the SET key until the desired set temperature is reached. The LCD screen set numbers will increase from 45° to 99° then restart over at 45°.
2. Release the SET key. The LCD screen will display the set temperature for 3 seconds, then ash the set temperature for 3 sec­onds, then the LCD screen will default to display the room temperature.
3. Press the MODE key to disengage the thermo mode. The word ROOM on the LCD screen will not show when the thermo is not in operation.
Note: The highest SET temperature is
99°F (32 °C) and the lowest temperature is 45°F (6°C).
REMOTE CONTROL OPERATION
NOTES
The Thermo Feature on the transmitter op­erates the appliance whenever the ROOM TEMPERATURE varies a certain number of degrees from the SET TEMPERATURE.
This variation is called the “swing” or tem­perature differential. The normal operating cycle of an appliance may be 4 times per hour depending on how well the room or home is insulated from the cold or drafts. The factory setting for the “swing number” is
2. This represents a temperature variation of
+/-2°F (1°C) between SET temperature and ROOM temperature, which determines when the replace will be activated. The transmitter has ON and OFF manual functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed the word ON or OF will appear on the LCD screen to show while the signal is being sent. Upon initial use, there may be a delay of three seconds before the remote receiver will respond to the transmitter. This is part of the system’s design.
Figure 28 - Manual Mode in ON Operation
Figure 29 - Manual Mode in OFF Operation
Setting°F/°C Scale
The factory setting for temperature is °F. To change this setting to °C, press the ON key and the OFF key on the remote control at the same time (see Figure 26, page 22). This will change from °F to °C. Follow this same pro­cedure to change from °C back to °F.
Manual Function
To operate the system in the manual “MODE” do the following.
ON OPERATION
Press the ON key and the appliance ame will come on. During this time the LCD screen will show ON (see Figure 28).
After 3 seconds the LCD screen will default to display room temperature and the word TEMP will show (see Figure 23). The ame icon will appear on LCD screen in manual on mode.
TEMP
TEMP
TEMP
OFF OPERATION
Press the OFF key and the appliance ame will shut off. During this time the LCD screen will show OF (see Figure 29).
After 3 seconds the LCD screen will default to display room temperature and the word TEMP will show (see Figure 29).
THERMOSTAT FUNCTION
Setting Desired Room Temperature
The remote control system can control the thermostat when the transmitter is in the THERMO mode. The word ROOM must be displayed on the screen.
To set the THERMO MODE and desired room temperature:
1. Press the MODE key until the LCD screen shows the word ROOM. The remote is now in the thermostatic mode.
Page 24
www.factorybuysdirect.com
200245-01A
24
INSPECTING BURNERS
IMPORTANT: Owner’s should check pilot ame pattern and burner ame pattern often. Incorrect ame patterns indicate the need for cleaning (see Care and Maintenance,
page 25) or service.
WARNING: Only a qualied service person should service and
repair heater. This includes maintenance requiring replacement or alteration of components.
PILOT FLAME PATTERN
Figure 30 - Correct Pilot Flame Pattern
(Natural Gas shown)
Figure 31 - Incorrect Pilot Flame Pattern
(Natural Gas shown)
Figure 30 shows a correct pilot ame pattern. Figure 31 shows an incorrect pilot ame pat­tern. The incorrect pilot ame is not touching the thermocouple. This will cause the ther­mocouple to cool, which shuts the heater off.
If pilot ame pattern is incorrect, as shown in Figure 31
• turn heater off (see To Turn Off Gas to Ap-
pliance, page 21)
• see Troubleshooting pages 26 through 29.
WARNING: If yellow tipping
occurs, your heater could pro­duce increased levels of carbon monoxide. If the burner ame pattern shows yellow tipping, follow instructions at bottom of this page.
Notice: Do not mistake orange ames with yellow tipping. Dirt or other ne particles enter
the heater and burn causing brief patches of
orange ame.
Approx. 3"-6" Above Top of Logs
Approx. 3"-6" Above Top of Logs
More Than 8" Above Top of Logs
Figure 32 - Correct Burner Flame Pattern
Figure 33 - Incorrect Burner Flame
Pattern
BURNER FLAME PATTERN
Figure 32 shows a correct burner ame pattern. Figure 33 shows an incorrect burner ame pattern. If burner ame pattern is incorrect then:
• turn heater off (see To Turn Off Gas to Appliance, page 21).
• see Troubleshooting pages 26 through 29.
BURNER PRIMARY AIR HOLES
Air is drawn into the burner through the holes in the tting at the entrance to the burner. These holes may become blocked with dust or lint. Periodically inspect these holes for any blockage and clean as necessary. Blocked air holes will create soot.
NG
3-3.5" WC
Natural Gas
Shown
LP
8-11" WC
NG
3-3.5" WC
Natural Gas
Shown
LP
8-11" WC
Page 25
www.factorybuysdirect.com
25
200245-01A
CARE AND MAINTENANCE
WARNING: Turn off heater and let cool before servicing.
CAUTION: You must keep control areas, burner, and circulating
air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualied service techni­cian. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.
WARNING: Failure to keep the primary air opening(s) of the
burner(s) clean may result in sooting and property damage.
MAIN BURNER
Periodically inspect all burner ame holes with the heater running. All slotted burner ame holes should be open with yellow ame pres­ent. All round burner ame holes should be open with a small blue ame present. Some
burner ame holes may become blocked by debris or rust, with no ame present. If so, turn off the heater and let it cool, and remove blockage or replace burner. Blocked burner ame holes will create soot.
Figure 34 - Burner and Injector Holder
CLEANING BURNER PILOT AIR INLET HOLE
We recommend that you clean the unit every 2,500 hours of operation or every three months. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSl. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can, you could damage the pilot assembly.
1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.
2. Inspect burner, pilot and primary air inlet holes on injector for dust and dirt (see Figure 34).
3. Blow air through the ports/slots and holes in the burner. Also clean the pilot assembly.
4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.
5. Blow air into the primary air holes on the injector holder.
6. In case any large clumps of dust have now been pushed into the burner. Repeat steps 3 and 4.
Injector
Burner Tube
Primary Air Inlet Holes
CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/ pilot unit.
Use a vacuum cleaner, pressurized air, or a small, soft bristled brush to clean.
A yellow tip on the pilot ame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about 2" from where the pilot ame comes out of the pilot assembly (see Figure
35). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.
Figure 35 - Pilot Inlet Air Hole
ODS/PILOT
(Back of pilot shown for clarity)
Pilot Air Inlet Hole
Natural Gas Burner
Propane/LP Gas Burner
Thermocouple
Pilot Air Inlet Hole
Ignitor Electrode
Page 26
www.factorybuysdirect.com
200245-01A
26
CARE AND MAINTENANCE
TROUBLESHOOTING
WARNING: If you smell gas:
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone. Fol-
low the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re department.
WARNING: Only a qualied service technician should service and repair heater. Make sure that power is turned off before proceeding. Turn off and let cool before servicing.
IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning sup­plies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors.
Note: All troubleshooting items are listed in order of operation.
CABINET
Air Passageways
Use a vacuum cleaner or pressurized air to clean.
Exterior
• Use a soft cloth dampened with a mild soap and water mixture.
• Wipe the cabinet to remove dust.
LOGS
• If you remove logs for cleaning, refer to Installing Logs, page 18, to properly replace logs.
• Replace log(s) if broken or chipped (dime-size or larger).
BLOWER (OPTIONAL ACCESSORY)
Refer to blower manual.
NG
Figure 30 - Gas Regulator Pressure Switch
Pressure Switch Set Screw
Pressure Switch
When using natural gas (NG), there is a pres­sure switch that acts to turn off the gas ow to the pilot if the inlet pressure exceeds 9" WC. This is to prevent the operation of the unit on the wrong gas (propane/LP). If your natural gas supply exceeds 9" WC the unit will not operate. Either contact your gas supplier to check and adjust the inlet pressure or a qualied service technician can bypass the pressure switch.
Before attempting to bypass the pressure switch, make sure the type of gas being used is correct. Check to make sure the connection tting is in the correct inlet on the regulator. Refer to Connecting to Gas Supply, page 14.
Problem Possible Cause Corrective Action
Using natural gas and pilot will not light.
Inlet pressure exceeds 9" WC. Bypass pressure switch. See
instructions below.
Only a qualied installer should bypass the pressure switch. To bypass the pressure switch locate the set screw on the regulator. Use a small at bladed screw driver to turn the set screw counterclockwise 2 turns. This will bypass the pressure switch function.
Page 27
www.factorybuysdirect.com
27
200245-01A
Problem Possible Cause Corrective Action
When ignitor button is pressed in, there is no spark at ODS/pilot
1. Ignitor electrode is posi­tioned wrong. Ignitor elec­trode is broken.
2. Ignitor electrode is not con­nected to ignitor cable.
3. Ignitor cable is pinched or wet.
4 Broken ignitor cable.
5. Bad piezo ignitor.
6. Low battery.
1. Replace electrode.
2. Replace ignitor cable
3. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry.
4. Replace ignitor cable.
5. Replace piezo ignitor.
6. Replace battery.
When ignitor button is pressed in there is a spark at ODS/pilot but no pilot ame present.
1. Gas supply is turned off or equipment shutoff valve is closed.
2. Control knob not fully pressed in while pressing ignitor button.
3. Air in gas lines (new instal­lation or recent gas interrup­tion).
4. ODS / pilot is clogged.
5. Incorrect inlet gas pressure or inlet regulator is damaged.
6. Control knob not in PILOT position.
7. Depleted gas supply (pro­pane).
1. Turn on gas supply or open equipment shutoff valve.
2. Fully press in control knob while pressing ignitor button.
3. Continue holding down con­trol knob. Repeat igniting op­eration until air is removed.
4.
Clean ODS/pilot (see Care and Maintenance, page 25) or
replace ODS/pilot assembly.
5. Check inlet gas pressure or replace inlet gas regulator.
6. Turn control knob to PILOT position.
7. Contact local propane/LP gas company.
ODS/pilot lights but ame goes out when control knob is released.
1. Control knob is not fully pressed in.
2. Control knob is not pressed in long enough.
3. Equipment shutoff valve is not fully open.
4. Thermocouple connection is loose at control valve.
5. Pilot flame not touching thermocouple, which allows thermocouple to cool, caus­ing pilot ame to go out. This problem could be caused by one or both of the following:
A) Low gas pressure B) Dirty or partially clogged
ODS/pilot
6. Thermocouple damaged.
7. Control valve damaged.
1. Press in control knob fully.
2. After ODS/pilot lights, keep control knob pressed in 30 seconds.
3. Fully open equipment shutoff valve.
4. Hand tighten until snug, and then tighten 1/4 turn more.
5. A) Contact local natural or propane/LP gas company
B) Clean ODS/pilot (see
Care and Maintenance,
page 25) or replace ODS/ pilot assembly
6. Replace thermocouple.
7. Contact customer service.
TROUBLESHOOTING
The entire gas delivery piping including connec­tions inside the heater should be leak tested by the qualied installer. After leak testing the quali­ed installer should light the appliance. Refer to
the correct ame pattern as illustrated on page
22. All ame patterns should be safely inside the product. If for any reason they are not, stop use of the appliance and call for repairs.
Page 28
www.factorybuysdirect.com
200245-01A
28
Problem Possible Cause Corrective Action
Burner(s) does not light after ODS/pilot is lit
1. Burner orice is clogged.
2. Burner orice diameter is too small.
3. Inlet gas pressure is too low.
1. Clean burner orifice (see
Care and Maintenance,
page 25) or replace burner orice.
2. Replace burner orice.
3. Contact local gas supplier.
Delayed ignition of burner(s).
1. Manifold pressure is too low.
2. Burner orice is clogged.
1. Contact local gas supplier.
2. Clean burner (see Care and Maintenance, page 25) or replace burner orice.
Burner backring during combustion
1. Burner orice is clogged or damaged.
2. Burner is damaged.
3. Gas regulator is damaged.
1. Clean burner orifice (see
Care and Maintenance,
page 25) or replace burner orice.
2. Contact dealer or customer service.
3. Replace gas regulator.
High yellow ame during burner combustion
1. Not enough air.
2. Gas regulator is defective.
3. Inlet gas pressure is too low.
1. Check burner for dirt and debris. If found, clean burner (see Care and Maintenance, page 25).
2. Replace gas regulator.
3. Contact local gas supplier.
Gas odor during com­bustion.
1. Foreign matter between control valve and burner.
2. Gas leak. (See Warning Statement at top of page 26).
1. Take apart gas tubing and remove foreign matter.
2. Locate and correct all leaks (see Checking Gas Connec- tions, page 16).
Slight smoke or odor dur­ing initial operation
1. Residues from manufactur­ing process.
1. Problem will stop after a few hours of operation.
Heater produces a whis­tling noise when burner is lit.
1. Air in gas line.
2. Air passageways on heater are blocked.
3. Dirty or partially clogged burner orice.
1. Operate burner until air is removed from line. Have gas line checked by local gas supplier.
2 Observe minimum installa-
tion clearances (Figure 4, page 9)
3 Clean burner (see Care and
Maintenance, page 25) or replace burner orice.
Heater produces a click­ing/ticking noise just after burner is lit or shut off.
1. Metal is expanding while heating or contracting while cooling.
1. This is common with most heaters. If noise is exces­sive, contact qualied ser­vice technician.
TROUBLESHOOTING
Page 29
www.factorybuysdirect.com
29
200245-01A
TROUBLESHOOTING
Problem Possible Cause Corrective Action
White powder residue forming within burner box or on adjacent walls or furniture
1. When heated, the vapors from furniture polish, wax, carpet cleaners, etc., turn into white powder residue.
1. Turn heater off when using furniture polish, wax, carpet cleaner or similar products.
Heater produces un­wanted odors.
1. Heater is burning vapors from paint, hair spray, glues, etc. See IMPORTANT statement, page 26.
2. Gas leak. See Warning State- ment at the top of page 26.
3 Low fuel supply.
1. Ventilate room. Stop using odor causing products while heater is running.
2. Locate and correct all leaks (see Checking Gas Connec- tions, page 16).
3. Rell supply tank (Propane/ LP models).
Heater shuts off in use (ODS operates).
1. Not enough fresh air is avail­able.
2. Low line pressure.
3. ODS/pilot is partially clogged.
1. Open window and/or door for ventilation.
2. Contact local gas supplier.
3. Clean ODS/pilot (see Care and Maintenance, page 25).
Gas odor exists even when control knob is in OFF position.
1. Gas leak. See Warning Statement at top of page 26.
2. Control valve is defective.
1. Locate and correct all leaks (see Checking Gas Connec- tions, page 16).
2. Contact customer service.
Moisture/condensation noticed on windows.
1. Not enough combustion/ ventilation air.
1. Refer to Air for Combus- tion and Ventilation require­ments, page 7.
REPLACEMENT PARTS
Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply original replacement parts, call Customer Service toll free at 1-855-607-6557 for referral information.
When calling Customer Service or your dealer, have ready:
• Your name
• Your address
• Model and serial number of your heater
• How heater was malfunctioning
• Type of gas supply and Propane/LP tank size
• Purchase date Usually, we will ask you to return the defective
part to the factory
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply original replacement part(s) call Customer Service toll free at 1-855-607-6557 for referral information.
When calling Customer Service have ready:
• Model number of your heater
• The replacement part number
Page 30
www.factorybuysdirect.com
200245-01A
30
PARTS
MODEL FDI32R
REMOTE
OFF
ON
LEARN
TEMP
15
17
21
19
22
16
18
23
20
8
9
11
13
14
12
12
6
2
10
3
4
5
7
1
Page 31
www.factorybuysdirect.com
31
200245-01A
PARTS
MODEL FDI32R
This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page 29 of this manual.
ITEM PART # DESCRIPTION QTY
1 FB32D600-02 Burner Assembly 1 2 ND0310A-400-P ODS Pilot 1 3 ML073-04 Ignitor Cable 1 4 OD-C0889-11 Solenoid 1 5 MRT-01 Control Valve 1 6 PIMDN1-01 Ignitor 1 7 RVD88-Y-4/9 Regulator 1 8 RG04-1M Receiver 1
9 RG04-1T Remote Control 1 10 FB32D201 Hood 1 11 FB32D104 Upper Decorative Trim 1 12 FB32D121 Left/Right Decorative Trim 2 13 FB32D100 Screen 1 14 PC32VFC-000B Louver Assembly 1
FB32D500 Log Assembly 1 15 FB32D501B Log 1 1 16 FB32D502B Log 2 1 17 FB32D503 Log 3 1 18 FB32D504 Log 4 1 19 FB32D505 Log 5 1 20 FB32D506 Log 6 1 21 FB32D507 Log 7 1 22 FB32D508 Log 8 1 23 FB32D509 Log 9 1
PART AVAILABLE - NOT SHOWN
FBD32D001 Hardware Package 1
PCAM-012 AAA Battery 3
PCAM-018 AA Battery 4
SERVICE HINTS
When Gas Pressure Is Too Low
• pilot will not stay lit
• burners will have delayed ignition
• replace will not produce specied heat
• propane/LP gas supply might be low (propane/LP units only) You may feel your gas pressure is too low. If so, contact your local gas supplier.
TECHNICAL SERVICE
You may have further questions about installation, operation, or troubleshooting. If so, contact Factory Buys Direct at 1-855-607-6557.
When calling, please have your model and serial numbers of your heater ready.
Page 32
200245-01 Rev. A 05/15
WARRANTY
KEEP THIS WARRANTY
Model _______________________________
Serial No. ____________________________
Date Purchased _______________________
Keep receipt for warranty verication.
REGISTER YOUR PRODUCT AT WWW.FACTORYBUYSDIRECT.COM
FACTORY BUYS DIRECT LIMITED WARRANTIES
New Products
Standard Warranty: Factory Buys Direct warrants this new product and any parts thereof to be free from defects in material and workmanship for a period of one (1) year from the date of rst purchase from an authorized dealer provided the product has been installed, maintained and operated in accordance with Factory Buys Direct’s warnings and instructions.
For products purchased for commercial, industrial or rental usage, this warranty is limited to 90 days from the date of rst purchase.
Factory Reconditioned Products
Limited Warranty: Factory Buys Direct warrants factory reconditioned products and any parts thereof to be free from defects in material and workmanship for a period 30 days from the date of rst purchase from an authorized dealer provided the product has been installed, maintained and operated in accordance with Factory Buys Direct’s warnings and instructions. No return will be authorized. Parts will be provided to repair the product.
Terms Common to All Warranties
The following terms apply to all of the above warranties:
Always specify model number and serial number when contacting the manufacturer. To make a claim under this warranty, the bill of sale or other proof of purchase must be presented.
This warranty is extended only to the original retail purchaser when purchased from an authorized dealer, and only when installed by a qualied installer in accordance with all local codes and instructions furnished with this product.
This warranty covers the cost of part(s) required to restore this product to proper operating condition and an allowance for labor when provided by a Factory Buys Direct Authorized Service Center or a provider ap­proved by Factory Buys Direct. Warranty parts must be obtained through authorized dealers of this product and/or Factory Buys Direct who will provide original factory replacement parts. Failure to use original factory replacement parts will void this warranty.
Traveling, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty repairs, unless expressly covered by this warranty, are not reimbursable under this warranty and are the responsibility of the owner.
Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents, improper installation, lack of proper maintenance, tampering or alteration(s).
This is Factory Buys Direct’s exclusive warranty, and to the full extent allowed by law; this express warranty excludes any and all other warranties, express or implied, written or verbal and limits the duration of any and all implied warranties, including warranties of merchantability and tness for a particular purpose to one (1) year on new products and 30 days on factory reconditioned products from the date of rst purchase.
Factory Buys Direct makes no other warranties regarding this product.
Factory Buys Direct’s liability is limited to the purchase price of the product and Factory Buys Direct shall not be liable for any other damages whatsoever under any circumstances including direct, indirect, incidental, or consequential damages.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
Factory Buys Direct 500 Brown Industrial Parkway Canton, GA 30114 1-855-607-6557
Loading...