Duluth Forge DFGE1008 Owner Manual

VENT-FREE GAS SYSTEM

US

OWNER'S OPERATION

AND INSTALLATION

MANUAL

MODELS

FBD400RT SERIES

This insert can be used in the following

mantel and replace systems:

FBD400RT-A-(AS,CH,TA,W)

HS400RT-MV-(WC,AS)

WARNING: If the information in this manual is not

®

followed exactly, a re or explosion may result causing property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable va-

pors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

—

Installation and service must be performed by a qualied installer, service agency or the gas supplier.

WARNING: This appliance is equipped for natural and propane/LP gas. Field conversion is not permitted other than between natural or propane/LP gases.

Questions, problems, missing parts? Before returning to your retailer, call

our customer service department at 1-866-573-0674, 7:30 am - 4:15 pm CST,

Monday through Friday or email customerservice@usaprocom.com

TABLE OF CONTENTS

Safety ........................................................ 3

Specications ............................................ 5

Qualied Installing Agency ........................ 5

Product Features ....................................... 5

Product Identication ................................. 6

Unpacking.................................................. 6

Local Codes............................................... 6

Water Vapor: A By-Product Of

Unvented Room Heaters ..................... 7

Air For Combustion and Ventilation ........... 7

Installation ................................................. 9

SAVE THIS BOOK

Operation ................................................. 17

Inspecting Burners................................... 23

Care And Maintenance ............................ 24

Troubleshooting ....................................... 26

Replacement Parts .................................. 29

Accessories ............................................. 29

Service Hints ........................................... 29

Technical Service..................................... 29

Parts ........................................................ 30

Warranty .................................................. 40

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

This is an unvented gas-red heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided.

Refer to Air for Combustion and Ventilation section on

page 7 of this manual.

WARNING: Improper installation, adjustment, al-

teration, service or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualied installer, service agency or the gas supplier.

This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with propane or natural gas. This appliance is equipped with a simple means to switch between propane and natural gas. Field conversion by any other means including the use of a kit is not permitted.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.

www.usaprocom.com

200102-01A2

SAFETY

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock and carbon monoxide poisoning. Failure

to follow these instructions will

void the warranty.

Only a qualied installer, service agent, or local gas supplier may install and service this product.

WARNING: Keep the appli-

ance area clear and free from

combustible materials, gasoline, and other ammable vapors and liquids.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchange insert or other accessory not approved for use with this heater.

WARNING: Do not allow fans

to blow directly into the heater. Avoid any drafts that alter burner ame pattern including ceiling fans. Altered burner patterns can cause sooting.

WARNING: Do not place clothing or other flammable material on or near the appliance. Never place any objects in the heater.

WARNING: Due to high temperatures, the appliance should be located out of trafc and away from furniture and draperies.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the u, with headaches, dizziness or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the inuence of alcohol and those at high altitudes.

Natural And Propane/LP Gas: Natural and Propane/LP gas are odorless. An odor-making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.

www.usaprocom.com

WARNING: Heater becomes very hot when running. Keep

children and adults away from

hot surfaces to avoid burns or clothing ignition. Heater will remain hot for a time after shutoff. Allow surfaces to cool before touching.

WARNING: Carefully supervise young children when they are in the room with the heater.

WARNING: Make sure a replace screen is in place before running heater.

3200102-01A

SAFETY

1. Do not place Propane/LP supply tank(s) inside any structure. Propane/LP supply tank(s) must be placed outdoors.

2. This heater should not be installed in a bedroom or bathroom.

3. This heater needs fresh air ventilation to run properly. This heater has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available. See Air for Combustion and Ventilation, page 7. If heater keeps shutting off, see Trouble- shooting, page 24.

4. Keep all air openings in front and bottom of heater clear and free of debris. This will ensure enough air for proper combustion.

5. If heater shuts off, do not relight until you have provided fresh, outside air. If heater keeps shutting off, have it serviced.

6. Do not run heater:

• Where ammable liquids or vapors are

used or stored.

• Under dusty conditions.

7. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

8. Always run heater with control knob at PILOT/IGN, LOW or HIGH locked positions. never set control knob between locked positions. Poor combustion and higher levels of carbon monoxide may result.

9. Do not use heater if any part has been under water. Immediately call a qualied service technician to inspect the room heater and to replace any part of the control system and any gas control which has been under water.

10. Turn off and unplug heater and let cool before servicing. Only a qualied service person should service and repair heater.

11. Operating heater above elevations of 4,500 feet could cause pilot outage.

12. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.

13. Do not use this heater as a wood-burning heater. Use only the logs provided with the heater.

14. To prevent the creation of soot, follow the instructions under Care and Maintenance page 22.

15. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of heater. After servicing, always replace screen before operating heater.

16. This log heater is designed to be smokeless. If logs ever appear to be smoking, turn off heater and call a qualied service technician. NOTE: During initial operating,

slight smoking could occur due to log curing and heater burning off manufacturing residues.

17. Solid fuels should not be burned in replace in which a vent-free log set is installed. Do not use this heater to cook food or burn paper or other objects.

18. Do not use this heater if any log is broken. Do not operate heater if a log is chipped (dime-size or larger).

www.usaprocom.com

200102-01A4

SPECIFICATIONS

MODEL FBD400RT

Gas Type Natural Propane/LP

Maximum Input Rating 32,000 BTU/Hr 32,000 BTU/Hr

Minimum Input Rating N/A N/A

Regulator Pressure Setting 4" W.C. 9" W.C.

Inlet Gas Pressure*

(inches of water)

* For purposes of input adjustment.

Ignition Electronic Piezo Ignitor Heater Dimensions (H x W x D) 29.5" x 29.1" x 15.6" Carton Dimensions (H x W x D) 31.1" x 31.5" x 18.1"

Stove Weight 69.5 lbs.

Shipping Weight 79.5 lbs.

Max. 10.5" W.C. Max. 14" W.C.

Min. 5" W.C. Min. 11" W.C.

FBD400RT

QUALIFIED INSTALLING AGENCY

Only a qualied agency should install and replace gas piping, gas utilization equipment or accessories, and repair and equipment servicing. The term “qualied agency” means any individual, rm, corporation, or company that either in person or through a representative is engaged in and is responsible for:

a) Installing, testing, or replacing gas piping

or

b) Connecting, installing, testing, repairing,

or servicing equipment; that is experienced in such work; that is familiar with all precautions required; and that has complied with all the requirement of the authority having jurisdiction.

PRODUCT FEATURES

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot shuts off the heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater is equipped with an electronic piezo control system. This system requires AAA batteries (provided).

www.usaprocom.com

THERMOSTAT HEAT CONTROL

The control automatically cycles the burner on and off to maintain a desired room tem-

perature.

2 GAS OPTIONS AVAILABLE

Your heater is equipped to operate on either Propane/LP or Natural gas. The heater is shipped from the factory ready for connecting to Propane/LP. The heater can easily be changed to Natural gas by having your qualied installer follow the instructions on page 10 and the markings on the heater.

5200102-01A

Hood

Screen

Logs

Heater Controls (Inside Panel)

PRODUCT IDENTIFICATION

Figure 1 - Vent-Free Fireplace Insert

UNPACKING

1. Remove top inner pack.

2. Tilt carton so that heater is upright.

3. Remove protective side packaging.

4. Slide heater out of carton. 5 Remove protective plastic wrap.

LOCAL CODES

Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code, ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02269-9101

6. Hold the screen, lift, and pull forward.

7. Remove log set by cutting plastic ties.

8. Carefully unwrap log.

9. Check for any shipping damage. If heater or log is damaged, promptly inform your dealer where you bought the heater.

State of Massachusetts: The installation must be made by a licensed plumber or gas tter in the Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-red supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

In the State of Massachusetts the gas cock must be a T-handle type. The State of Massachusetts requires that a exible appliance connector cannot exceed three feet in length.

www.usaprocom.com

200102-01A6

WATER VAPOR: A BY-PRODUCT OF

UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30 mL) of water for every 1,000 BTUs (0.3 KWs) of gas input per hour. Unvented room heaters are recommended as supplemental heat (a room) rather than a primary heat source (an entire house). In most supplemental heat applications, the water vapor does not create a problem. In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather.

AIR FOR COMBUSTION AND VENTILATION

The following steps will help ensure that water vapor does not become a problem.

1. Be sure the heater is sized properly for the application, including ample combustion air and circulation air.

2. If high humidity is experienced, a dehumidier may be used to help lower the water vapor content of the air.

3. Do not use an unvented room heater as the primary heat source.

WARNING: This heater shall

not be installed in a conned space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home.

Today’s homes are built more energy efcient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible. While it is good to make your home energy efcient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation. Exhaust fans, replaces, clothes dryers and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

WARNING: This heater

shall not be installed in a room or space unless the required volume of indoor combustion air is provided by the method described in the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code, or applicable local codes.

WARNING: If the area in which

the heater may be operated does not meet the required volume for indoor combustion air, combustion and ventilation air shall be provided by one of the methods described in the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code, or applicable local codes.

www.usaprocom.com

7200102-01A

AIR FOR COMBUSTION AND VENTILATION

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconned space. When ventilating to an adjoining unconned space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the oor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Air for Combustion and Ventilation for required size of ventilation

grills or ducts.

12"

Ventilation

Grills into Adjoining

Room,

Option 1

Or

Remove Door into Adjoining

Room,

Option 3

Figure 2 - Ventilation Air from Inside

Ventilation Grills

Into Adjoining Room,

12"

Building

Option 2

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the oor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation for required size

of ventilation grills or ducts. IMPORTANT: Do not provide openings

for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent. Rework worksheet, adding the space of the adjoining unconned space. The combined spaces must have enough fresh air to supply all appliances in both spaces.

Ventilated Attic

Crawl Space

Ventilated

To Attic

To

Crawl

Space

Outlet Air

Inlet Air

Outlet Air

Inlet Air

Figure 3 - Ventilation Air from Outdoors

www.usaprocom.com

200102-01A8

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualied service person must install heater. Follow all local codes.

WARNING: Before installing in a solid fuel burning replace, the chimney ue and rebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner. Creosote will ignite if highly heated. A dirty chimney ue may create and distribute soot within the house. Inspect chimney ue and rebox for damage. If damaged, repair ue before operating heater.

WARNING: Seal any fresh

air vents or ash clean-out doors located on oor or wall of replace. If not, drafting may cause pilot outage or sooting. Use a heat-resistant sealant. Do not seal chimney ue damper.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other ammable objects are less than 42" from the front, top, or sides of the heater.

• in high trafc areas

• in windy or drafty areas

CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as tobacco smoke, aromatic candles, cleaning uids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

This rebox can not be installed in a built-in replace. This rebox may only be installed in a ProCom Heating, Inc. mantel accessory approved for this product.

IMPORTANT: Vent-free heaters add moisture to the air. Although this is benecial, installing heater in rooms without enough ventilation air may cause mildew to form too much moisture. See Air for Combustion and Ventilation, page 7.

CHECK GAS TYPE

Be sure your gas supply is right for your heater. Otherwise, call dealer where you bought the heater for proper type heater.

www.usaprocom.com

9200102-01A

INSTALLATION

GAS SELECTION

This appliance is factory preset for propane/LP gas. No changes are required for connecting to propane/LP.

Only a qualified installer or service technician can perform gas selection and connecting to gas supply.

CAUTION: Two gas line in-

stallations at the same time are

prohibited. The access plate to the simple switching means shall not be opened while the heater is in operation.

CAUTION: To avoid gas leakage at the inlet of regulator, a qualied installer or service technician must use supplied hex plug with sealant.

WARNING: Do not attempt to access or change the setting of the fuel selection means.

Access to and adjustment of the fuel selection means must only be performed by a qualied service person when connecting this appliance to a specied fuel supply at the time of installation.

Change of the selector setting to other than the fuel type specied at the time of installation could damage this appliance and render it inoperable.

The installer shall replace the access cover before completing the installation and operating this appliance.

For changing from propane to

1. Remove bottom screw from cover plate

2. For NATURAL GAS, press in knob using

3. Rotate and close cover over fuel selection

4. Remove hex plug (with wrench provided)

Cover Plate for Fuel Selection Device

Fuel Selector Knob

natural gas supply:

located on back side of heater (see Figure

4). Rotate to expose fuel selection device.

a at screwdriver with a blade with thickness of a quarter and turn knob clockwise

until the knob locks into the NG position (see Figure 5). Fuel selection device must be locked in the NG position. Do not operate heater between locked positions!

device and reinstall screws.

from natural gas inlet of regulator (see Figure 5). Install gas line into NG inlet of regulator. Use thread sealant to assure there are no leaks.

Back Side of Heater

NG

LP

Gas Regulator Inlet Connections

Figure 4 - Gas Control Locations

Gas Connection Fitting

NG

LP

Hex Plug

Gas Inlet Gas esté

NG

LP

Figure 5 - Settings for Natural Gas

www.usaprocom.com

Left Side of HeaterBack of Heater

Selection

200102-01A10

Left Side of HeaterBack of Heater

INSTALLATION

For changing from natural gas

supply to propane supply:

1. Remove bottom screw from cover plate located on left side of heater (see Figure 4, page 10). Rotate to expose fuel selection device.

2. For propane gas, press in knob using a at screwdriver with a blade the thickness of a quarter and turn knob counterclockwise

until the knob locks into the LP position (see Figure 6). Fuel selection device must be locked in the LP position. Do not operate heater between locked positions.

3. Rotate and close cover over fuel selection device and reinstall screw.

4. Remove hex plug (with wrench provided) from propane/LP gas inlet of regulator (see Figure 6). Install gas line into LP inlet of regulator. Use thread sealant to assure there are no leaks.

Fuel Selector Knob

NG

Hex Plug

NG

Gas

LP

Connection Fitting

Gas Inlet Gas esté

LP

CLEARANCES TO

COMBUSTIBLES

WARNING: You must main-

tain the minimum clearances. If possible, provide greater clearances from oor, ceiling, and adjoining wall. Measure from outermost point of heater.

Note: This rebox can not be installed in an existing replace. Install this rebox only in a ProCom Heating, Inc. mantel accessory

approved for this product.

Minimum Clearances For Side

Combustible Material, Side Wall

and Ceiling

A. Clearance from the side of the replace to

any combustible material and wall should not be less than 12" (see Figure 7).

B. Clearance from the top of the replace to

the ceiling must not be less than 48".

Figure 6 - Settings for Propane/LP Gas

Selection

Figure 7 - Minimum Clearance for

Combustible to Wall and Ceiling

MANTEL

Assemble and install your mantel at this time. Mantel instructions are inside the mantel box. Mantel must be in place before you connect to the gas supply.

www.usaprocom.com

11200102-01A

INSTALLATION

CONNECTING TO GAS SUPPLY

WARNING: A qualied service technician must connect heater to gas supply. Follow all local codes.

WARNING: This appliance requires a 3/8" NPT (National Pipe Thread) inlet connection to the pressure regulator.

WARNING: Do not overtighten gas connections.

WARNING: For natural gas, Never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas.

CAUTION: For propane/ LP gas, never connect heater directly to the gas supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and propane/LP supply. Gas supplier provides external regulator for natural gas. The installer provides the external regulator for propane/LP gas.

CAUTION: Use only new, black iron or steel pipe. Internally tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of pressure will occur.

CAUTION: For natural gas, check your gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 10.5" WC. If gas line pressure is higher, heater regulator damage could occur.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting into gas piping and/or ttings.

CAUTION: Use pipe joint sealant that is resistant to gas (Propane/LP or Natural Gas).

Before installing heater, make sure you have the items listed below:

• external regulator for propane/LP unit only (supplied by installer)

• piping (check local codes)

• sealant (resistant to natural gas and propane/LP gas)

• equipment shutoff valve*

• test gauge connection*

• sediment trap

• tee joint

• pipe wrench

• exible gas hose (check local codes)

* A CSA design-certied equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design certied equipment shutoff valve from your dealer.

www.usaprocom.com

200102-01A12

INSTALLATION

Typical Inlet Pipe Diameters

Use 3/8" black iron pipe or greater. Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 8).

IMPORTANT: Install an equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

For propane/LP installations, apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.

For propane/LP gas, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must

Ground Joint Union

Tee Joint

Reducer

Test Gauge Connection*

Sediment

Trap

Bushing to 1/8" NPT

1/8" NPT Plug Tap

Tee Joint

Pipe Nipple

Gap

3" Minimum

reduce incoming gas pressure to between 11" and 14" of water. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 9. Pointing the vent down protects it from freezing rain or sleet.

Install sediment trap in supply line as shown in Figure 8. Place sediment trap where it is within reach for cleaning. Place sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once (see page 14).

3/8" NPT

Pipe Nipple

Equipment Shutoff Valve

Natural Gas

From Gas Meter (5" W.C.** to

10.5" W.C. Pressure)

Propane/LP

From External Regulator (11" W.C.** to 14" W.C. Pressure)

Propane/LP Supply Tank

External Regulator with Vent Pointing Down

* Purchase the optional CSA design-certied equipment

Figure 8 - Gas Connection

shutoff valve from your dealer.

www.usaprocom.com

Figure 9 - External Regulator

with Vent Pointing Down

13200102-01A

INSTALLATION

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections, internal and

external to unit, for leaks after installing or servicing. Correct all leaks at once.

WARNING: Never use an open ame to check for a leak. Apply a noncorrosive leak detection uid to all joints. If bubbles form, there is a leak. Correct all leaks at once.

PRESSURE TESTING GAS SUPPLY

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect heater with its appliance main

2. Cap off open end of gas pipe where equip-

3. Pressurize supply piping system by either

4. Check all joints of gas supply piping sys-

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff

Test Pressures Equal To or Less Than

1.

2. Pressurize supply piping system by either

3. Check all joints from gas meter to equip-

4. Correct all leaks at once.

PIPING SYSTEM

gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 PSIG will damage heater regulator.

ment shutoff valve was connected.

opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.

tem. Apply noncorrosive leak detection uid to all joints. If bubbles form, there may be a leak.

valve to gas supply. Check reconnected ttings for leaks.

1/2 PSIG (3.5 kPa)

Close equipment shutoff valve (see Figure 10).

opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.

ment shutoff valve for natural gas or propane/LP supply to equipment shutoff valve for propane/LP (see Figure 11 or 12). Apply a noncorrosive leak detection uid to all joints. Bubbles forming show a leak.

www.usaprocom.com

Equipment Shutoff Valve

Figure 10 - Equipment Shutoff Valve

Propane/LP Supply Tank

External Regulator

Figure 11 - Checking Gas Joints for

Gas Meter

Equipment Shutoff Valve

Figure 12 - Checking Gas Joints for

PRESSURE TESTING HEATER GAS

1. Open equipment shutoff valve (see Figure 10).

2. Open main gas valve located on or near gas meter for natural gas or open propane/LP supply tank valve.

3. Make sure control knob of heater is in the OFF position.

4. Check all joints from equipment shutoff valve to control valve (see Figure 11 or 12). Apply a noncorrosive leak detection uid to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light heater (see Lighting Instructions on page 17). Check all other internal joints for leaks.

7. Turn off heater (see To Turn Off Gas Ap- pliance, page 18).

Equipment Shutoff Valve

Propane/LP Gas

Natural Gas

CONNECTIONS

Open

Closed

Control Valve Location

200102-01A14

INSTALLATION

INSTALLING LOGS

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specically approved with this heater may result in property damage or personal injury.

CAUTION: After installation and periodically thereafter, check to ensure that no yellow ame comes in contact with any log. With the heater set to High, check to see if yellow ames contact any log. If so, reposition logs according to the log

installation instructions in this

manual. Yellow ames contacting logs will create soot.

It is very important to install the logs exactly as instructed. Do not modify logs. Use only logs supplied with heater. Each log is marked with a number. This number will help you to identify the logs when installing. After installing logs, add decorative cinders around the grate base, do not place any decorative cinders on logs or burner.

1. Install pins on log #1 into the two slots in the bracket attached to rear wall (see Figure 13).

2. Install pins on log #2 into the two slots in left side of the middle bracket (see Figure 13 and Figure 14).

3. Install pins on log #3 into the two slots in right side of the middle bracket (see Figure 13 and Figure 14).

4. Install pins on log #4 onto the two slots in the front bracket (see Figure 14 and Figure 15, page 16).

5. Insert the recessed hole on the bottom of log #5 onto the pin on log #2 (see Figures 15 and 16, page 16).

6. Insert the pin on log #6 into the hole on log #3 (see Figures 15 and 16, page 16).

IMPORTANT: Make sure logs do not cover any burner ports. It is very important to install the logs exactly as instructed. Do not modify logs. Use only logs supplied with heater.

Slots in Rear Plate

Log #1

Slots for Log #2

Figure 13 - Installing Log #1

Log #2

Slots for Log #4

Figure 14 - Installing Logs #2 and #3

Slots for Log #3

Log #3

www.usaprocom.com

15200102-01A

INSTALLATION

Pin for Log #5

Hole for Log #6

Log #4

Figure 15 - Installing Log #4

INSTALLING BATTERIES

CAUTION: Do not mix old and new batteries. Do not mix alkaline, standard (carbon - zinc), or rechargeable (nickel - cadmium) batteries. Do not dispose of batteries in re, batteries may explode or leak.

• Batteries are included.

• Remove batteries when depleted.

• Install/replace the batteries according to the type and quantity stated in table below.

• Do not mix old and new batteries. New batteries should be the same brand for best results.

• Be sure to observe proper polarity (+/-) when installing or replacing the batteries. Damage due to improper battery installation may void the warranty on the product.

• For remote control systems, maximize battery life by turning off the receiver when it is not in use.

• For long periods of non-operation, remove batteries from all components for safety.

Component Type of Battery Qty.

Ignitor AAA 1

Remote Control AAA 2 or 3*

Remote Receiver AA 4

*Note: Quantity depends on model of remote

control.

Unscrew ignitor cap and install a AAA battery with the + pointing out. Replace cap.

Ignitor

www.usaprocom.com

Log #5

Log #6

Figure 16 - Installing Log #5 and #6

AAA

Battery

Positive

UP

Figure 17 - Installing Battery in Ignitor

Receiver and Remote Control

Batteries are required in both the Remote Control (Transmitter) (2 AAA size) and Receiver (4 AA size) (see Figure 18).

Note: Be sure batteries are placed correctly.

Reversing the batteries can cause damage to the receiver and remote. Replace all batteries

on a yearly basis or sooner.

Position the slide switch on the front of the receiver box in the ON position before installing batteries. Once the batteries are installed you will hear a single beep which indicates the batteries are charged. If you do not hear a beep, replace with new batteries.

AA

LEARN

Receiver

OFF

REMOTE

ON

AAA

Remote Control (Transmitter)

Figure 18 - Installing Batteries in Remote

Control and Receiver

200102-01A16

OPERATION

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not fol-

low these instructions exactly,

a re or explosion may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must

be lighted by hand. When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to smell next to the oor because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

LIGHTING INSTRUCTIONS

WARNING: You must oper-

ate this heater with the screen

in place. Make sure screen is installed before running heater.

NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange ame will also be present. Open damper or window to vent smell. This will only last a few hours.

1. STOP! Read the safety information above.

2. Open screen.

3. Make sure equipment shutoff valve is fully

open.

4. Push in control knob slightly and turn

clockwise to the OFF position (see Figure 19).

5. Wait ve (5) minutes to clear out any gas.

Then smell for gas around heater and near the oor. If you smell gas, STOP! Follow "B" in the safety information above. If you do not smell gas, go to the next step.

not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualied service technician. Force or attempted repair may result in a re or explosion.

D. Do not use this appliance if any part

has been under water. Immediately call a qualied service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

6. Push in control knob slightly and turn counterclockwise to the PILOT position. Press in control knob for ve (5) seconds.

Note: The rst time that the heater is

operated after connecting the gas supply,

the control knob should be pressed for

about thirty (30) seconds. This will allow air to bleed from the gas system. If pilot does not stay lit, refer to Troubleshooting,

pages 24 though 26. Also contact a quali-

ed service technician or gas supplier for

repairs. Until repairs are made, light pilot

with match.

• If control knob does not pop up when

released, contact a qualified service technician or gas supplier for repairs.

Remote Receiver

Figure 19 - Heater Control Locations

Ignitor

Control Knob

www.usaprocom.com

17200102-01A

OPERATION

8. With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the rear of the burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, refer to

Troubleshooting, pages 24 though 26.

Also contact a qualied service technician

or gas supplier for repairs. Until repairs

are made, light pilot with match. To light pilot with match, see Manual Lighting

Procedure.

9. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

Note: If pilot goes out, repeat steps 4

through 9. This heater has a safety interlock system. Wait one (1) minute before

lighting pilot again.

10. Be sure the slide switch on the front of the receiver box is in the ON position.

11. Turn control knob counterclockwise to the ON position. The main burner should light.

TO TURN OFF GAS TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise to the OFF position.

Note: If burner does not light, push the

slide switch on the receiver box to the OFF

position, then back to the ON position.

Note: Please wait one minute after shut-

ting off heater to allow the control valve

to reset before starting again.

13. Make sure heater screen is in place before operating heater.

14. If heater will not operate, follow the instructions To Turn Off Gas To Appliance, and call your service technical or gas supplier.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

WARNING: If input gas type is NG, make sure NG pilot burner ignites. If input gas type is LP, make sure LP pilot burner ignites. See Figure 31, page 25.

Shutting Off Burner Only (pilot

stays lit)

Turn control knob clockwise to the PILOT position.

MANUAL LIGHTING PROCEDURE

1. Open screen.

2. Follow steps 1 through 7 under Lighting Instructions, page 17.

3. With control knob in the PILOT position, strike a match, and hold near pilot. Press in control knob; pilot should light.

www.usaprocom.com

4. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

5. Make sure the heater screen is in place before operating heater.

200102-01A18

OPERATION

REMOTE CONTROL SYSTEM

Programming the Remote and Receiver

The remote and receiver must be “learned” to one another.

To prepare the receiver box for learning, use a pen or small screwdriver to gently press and hold the learn button until you hear 3 series of beeps.

1. Place the slide switch on the receiver in the remote position (see Figure 21).

2. Turn control knob on the heater to the ON position.

3. Use a pen or small screwdriver to gently press and hold the recessed LEARN button on the face of the receiver for 2-3 seconds. You will hear a beep.

4. Press the ON button on the remote control to light the burner (see Figure 21). You will hear a series of beeps. This will also "learn", or program, the remote and the receiver.

Note: Remote must be at least 5 feet

away from the receiver during the learning

process.

Note: If the remote control is lost or dam-

aged, the slide switch on the receiver can

be used to operate the heater.

Note: When batteries are replaced the

learning process above must be repeated.

Learn Button

LEARN

REMOTE OFF

ON

ON - Operates unit to on position, manually

Key Settings

operated solenoid ON. OFF - Operates unit to off position, manually

operated solenoid OFF. MODE - Changes unit from manual mode to

thermo mode. SET - Sets temperature in thermo mode.

TEMP

Figure 21 - Remote Control

LCD Liquid Crystal Display

1. DISPLAY Indicates CURRENT room temperature.

2. °F or °C Indicates degrees Fahrenheit or Celsius.

3. FLAME Indicates burner/valve in operation.

4. ROOM Indicates remote is in THERMO

operation.

5. TEMP Appears during manual operation.

6. SET Appears during time the of setting

the desired temperature in the thermo operation.

Slide Switch

Figure 20 - Receiver

Remote Control Operation

This appliance must not be used with glass doors in the closed position. This can lead to pilot outages and severe sooting outside the replace.

The transmitter operates on 2 AAA batteries.

www.usaprocom.com

1

2

3

4

ROOM SET TEMP

5

6

Figure 22 - Remote Control Display

19200102-01A

OPERATION

TEMP

The factory setting for temperature is °F. To

Setting°F/°C Scale

change this setting to °C, press the ON key and the OFF key on the remote control at the same time (see Figure 21, page 19). This will change from °F to °C. Follow this same procedure to change from °C back to °F.

Manual Function

To operate the system in the manual “MODE” do the following.

ON OPERATION

Press the ON key and the appliance ame will come on. During this time the LCD screen will show ON (see Figure 23).

After 3 seconds the LCD screen will default to display room temperature and the word TEMP will show (see Figure 23). The ame icon will appear on LCD screen in manual on mode.

TEMP

Figure 23 - Manual Mode in ON Operation

OFF OPERATION

Press the OFF key and the appliance ame will shut off. During this time the LCD screen will show OF (see Figure 24).

After 3 seconds the LCD screen will default to display room temperature and the word TEMP will show (see Figure 24).

TEMP

Figure 24 - Manual Mode in OFF Operation

THERMOSTAT FUNCTION

Setting Desired Room Temperature

The remote control system can control the thermostat when the transmitter is in the THERMO mode. The word ROOM must be displayed on the screen.

To set the THERMO MODE and desired room temperature:

1. Press the MODE key until the LCD screen shows the word ROOM. The remote is now in the thermostatic mode.

2. Press and hold the SET key until the desired set temperature is reached. The LCD screen set numbers will increase from 45° to 99° and then restart over at 45°.

3. Release the SET key. The LCD screen will display the set temperature for 3 seconds, then ash the set temperature for 3 seconds, then LCD screen will default to display the room temperature.

To Change The Set Temperature

1. Press and hold the SET key until the desired set temperature is reached. The LCD screen set numbers will increase from 45° to 99° then restart over at 45°.

2. Release the SET key. The LCD screen will display the set temperature for 3 seconds, then ash the set temperature for 3 seconds, then the LCD screen will default to display the room temperature.

3. Press the MODE key to disengage the thermo mode. The word ROOM on the LCD screen will not show when the thermo is not in operation.

Note: The highest SET temperature is

99°F (32 °C) and the lowest temperature is 45°F (6°C).

REMOTE CONTROL OPERATION

NOTES

The Thermo Feature on the transmitter operates the appliance whenever the ROOM TEMPERATURE varies a certain number of degrees from the SET TEMPERATURE.

This variation is called the “swing” or temperature differential. The normal operating cycle of an appliance may be 4 times per hour depending on how well the room or home is insulated from the cold or drafts. The factory setting for the “swing number” is

2. This represents a temperature variation of

+/-2°F (1°C) between SET temperature and ROOM temperature, which determines when the replace will be activated. The transmitter has ON and OFF manual functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed the word ON or OF will appear on the LCD screen to show while the signal is being sent. Upon initial use, there may be a delay of three seconds before the remote receiver will respond to the transmitter. This is part of the system’s design.

www.usaprocom.com

200102-01A20

INSPECTING BURNERS

Approx. 3"-6" Above Top of Logs

IMPORTANT: Owner’s should check pilot ame pattern and burner ame pattern often. Incorrect ame patterns indicate the need for cleaning (see Care and Maintenance,

page 22) or service.

WARNING: Only a qualied service person should service and repair heater. This includes maintenance requiring replacement or alteration of components.

PILOT FLAME PATTERN

Figure 25 shows a correct pilot ame pattern. Figure 26 shows an incorrect pilot ame pattern. The incorrect pilot ame is not touching the thermocouple. This will cause the thermocouple to cool, which shuts the heater off.

If pilot ame pattern is incorrect, as shown in Figure 26

• turn heater off (see To Turn Off Gas to Ap- pliance, page 18)

• see Troubleshooting pages 25 through 26.

WARNING: If yellow tipping

occurs, your heater could pro-

Notice: Do not mistake orange ames with yellow tipping. Dirt or other ne particles enter

the heater and burn causing brief patches of

orange ame.

Figure 25 - Correct Pilot Flame Pattern

(Natural Gas shown)

duce increased levels of carbon monoxide. If the burner ame pattern shows yellow tipping, follow instructions at bottom of this page.

Figure 27 shows a correct burner ame pattern. Figure 28 shows an incorrect burner ame pattern. If burner ame pattern is incorrect then:

• turn heater off (see To Turn Off Gas to Appliance, page 18).

• see Troubleshooting pages 24 through 26.

Figure 27 - Correct Burner Flame Pattern

Air is drawn into the burner through the holes in the tting at the entrance to the burner. These holes may become blocked with dust or lint. Periodically inspect these holes for any blockage and clean as necessary. Blocked air holes will create soot.

Figure 26 - Incorrect Pilot Flame Pattern

(Natural Gas shown)

BURNER FLAME PATTERN

More Than 8" Above Top of Logs

Figure 28 - Incorrect Burner Flame

BURNER PRIMARY AIR HOLES

www.usaprocom.com

Pattern

21200102-01A

CARE AND MAINTENANCE

WARNING: Turn off heater and let cool before servicing.

CAUTION: You must keep control areas, burner, and circulating

air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualied service technician. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

WARNING: Failure to keep the primary air opening(s) of the

burner(s) clean may result in sooting and property damage.

MAIN BURNER

Periodically inspect all burner ame holes with the heater running. All slotted burner ame holes should be open with yellow ame present. All round burner ame holes should be open with a small blue ame present. Some

BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE

We recommend that you clean the unit every 2,500 hours of operation or every three months. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSl. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can, you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow

the unit to cool for at least thirty minutes.

2. Inspect burner, pilot and primary air inlet

holes on injector for dust and dirt (see Figure 29).

3. Blow air through the ports/slots and holes

in the burner. Also clean the pilot assembly.

burner ame holes may become blocked by debris or rust, with no ame present. If so, turn off the heater and let it cool, and remove blockage or replace burner. Blocked burner ame holes will create soot.

4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the injector holder.

6. In case any large clumps of dust have now been pushed into the burner. Repeat steps 3 and 4.

Burner Tube

Primary Air Inlet Holes

Figure 29 - Burner and Injector Holder

Injector

www.usaprocom.com

200102-01A22

CARE AND MAINTENANCE

ODS/PILOT

Ignitor

CAUTION: Never use a wire,

needle, or similar object to clean

Natural Gas Burner

ODS/pilot. This can damage ODS/ pilot unit.

Use a vacuum cleaner, pressurized air, or a small, soft bristled brush to clean.

A yellow tip on the pilot ame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about 2" from where the pilot ame comes out of the pilot assembly (see Figure 30). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Air Passageways

Use a vacuum cleaner or pressurized air to clean.

• If you remove logs for cleaning, refer to Installing Logs, page 15, to properly replace logs.

• Replace log(s) if broken or chipped (dime-size or larger).

Pilot Air Inlet Hole

Figure 30 - Pilot Inlet Air Hole

CABINET

• Use a soft cloth dampened with a mild soap

and water mixture.

• Wipe the cabinet to remove dust.

LOGS

Electrode

Pilot Air Inlet Hole

Exterior

Thermocouple

Propane/LP Gas Burner

www.usaprocom.com

23200102-01A

TROUBLESHOOTING

WARNING: If you smell gas:

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

WARNING: Only a qualied service technician should service and repair heater. Make sure that power is turned off before proceeding. Turn off and let cool before servicing.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors.

Note: All troubleshooting items are listed in order of operation.

Problem Possible Cause Corrective Action

When ignitor button is pressed in, there is no spark at ODS/pilot.

When ignitor button is pressed in there is a spark at ODS/pilot but no ignition.

1. Ignitor electrode is positioned wrong. Ignitor electrode is broken.

2. Ignitor electrode is not connected to ignitor cable.

3. Ignitor cable is pinched or wet.

4 Broken ignitor cable.

5. Bad piezo ignitor.

6. Low battery.

1. Gas supply is turned off or equipment shutoff valve is closed.

2. Control knob not fully pressed in while pressing ignitor button.

3. Air in gas lines (new installation or recent gas interruption).

4. ODS / pilot is clogged.

5. Incorrect inlet gas pressure or inlet regulator is damaged.

6. Control knob not in PILOT position.

7. Depleted gas supply (propane).

1. Replace electrode.

2. Replace ignitor cable.

3. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry.

4. Replace ignitor cable.

5. Replace piezo ignitor.

6. Replace battery.

1. Turn on gas supply or open equipment shutoff valve.

2. Fully press in control knob while pressing ignitor button.

3. Continue holding down control knob. Repeat igniting operation until air is removed.

4.

Clean ODS/pilot (see Care and Maintenance, page 22) or

replace ODS/pilot assembly.

5. Check inlet gas pressure or replace inlet gas regulator.

6. Turn control knob to PILOT position.

7. Contact local propane/LP gas company.

www.usaprocom.com

200102-01A24

TROUBLESHOOTING

Problem Possible Cause Corrective Action

ODS/pilot lights but ame goes out when control knob is released.

Burner does not light after ODS/pilot is lit.

Delayed ignition of burner.

Burner backring during combustion.

High yellow ame during burner combustion.

Gas odor during combustion.

1. Control knob is not fully pressed in.

2. Control knob is not pressed in long enough.

3. Equipment shutoff valve is not fully open.

4. Thermocouple connection is loose at control valve.

5. Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot ame to go out. This problem could be caused by one or both of the following:

A) Low gas pressure B) Dirty or partially clogged

ODS/pilot

6. Thermocouple damaged.

7. Control valve damaged.

1. Burner orice is clogged.

2. Burner orice diameter is too small.

3. Inlet gas pressure is too low.

1. Manifold pressure is too low.

2. Burner orice is clogged.

1. Burner orice is clogged or damaged.

2. Burner is damaged.

3. Gas regulator is damaged.

1. Not enough air.

2. Gas regulator is defective.

3. Inlet gas pressure is too low.

1. Foreign matter between control valve and burner.

2. Gas leak. (See Warning Statement at top of page 26).

1. Press in control knob fully.

2. After ODS/pilot lights, keep control knob pressed in 30 seconds.

3. Fully open equipment shutoff valve.

4. Hand tighten until snug, and then tighten 1/4 turn more.

5. A) Contact local natural or propane/LP gas company

B) Clean ODS/pilot (see

Care and Maintenance, page 22) or replace ODS/ pilot assembly

6. Replace thermocouple.

7. Replace control valve.

1. Clean burner orifice (see Care and Maintenance, page 22) or replace burner orice.

2. Replace burner orice.

3. Contact local gas supplier.

1. Contact local gas supplier.

2. Clean burner (see Care and Maintenance, page 22) or replace burner orice.

1. Clean burner orifice (see Care and Maintenance, page 22) or replace burner orice.

2. Replace burner.

3. Replace gas regulator.

1. Check burner for dirt and debris. If found, clean burner (see Care and Maintenance, page 22).

2. Replace gas regulator.

3. Contact local gas supplier.

1. Contact a qualied service technician to remove foreign matter.

2. Locate and correct all leaks (see Checking Gas Connec- tions, page 14).

www.usaprocom.com

25200102-01A

TROUBLESHOOTING

Problem Possible Cause Corrective Action

Slight smoke or odor during initial operation.

Heater produces a whistling noise when burner is lit.

Heater produces a clicking/ticking noise just after burner is lit or shut off.

White powder residue forming within burner box or on adjacent walls or furniture.

Heater produces unwanted odors.

Heater shuts off in use (ODS operates).

Gas odor exists even when control knob is in OFF position.

Moisture/condensation noticed on windows.

1. Residues from manufacturing process.

1. Turning control knob to high position when burner is cold.

2. Air in gas line.

3. Air passageways on heater are blocked.

4. Dirty or partially clogged burner orice.

1. Metal is expanding while heating or contracting while cooling.

1. When heated, the vapors from furniture polish, wax, carpet cleaners, etc., turn into white powder residue.

1. Heater is burning vapors from paint, hair spray, glues, etc. See IMPORTANT statement, page 26.

2. Gas leak. See Warning State- ment at the top of page 26.

3 Low fuel supply.

1. Not enough fresh air is available.

2. Low line pressure.

3. ODS/pilot is partially clogged.

1. Gas leak. See Warning Statement at top of page 26.

2. Control valve is defective.

1. Not enough combustion/ ventilation air.

1. Problem will stop after a few hours of operation.

1. Turn control knob to low position and let warm up for a minute.

2. Operate burner until air is removed from line. Have gas line checked by local gas supplier.

3 Observe minimum installa-

tion clearances (Figure 7, page 11).

4 Clean burner (see Care and

Maintenance, page 22) or replace burner orice.

1. This is common with most heaters. If noise is excessive, contact qualied service technician.

1. Turn heater off when using furniture polish, wax, carpet cleaner or similar products.

1. Open a window to ventilate room. Stop using odor causing products while heater is running.

2. Locate and correct all leaks (see Checking Gas Connec- tions, page 14).

3. Rell supply tank (Propane/ LP models).

1. Open window and/or door for ventilation.

2. Contact local gas supplier.

3. Clean ODS/pilot (see Care and Maintenance, page 22).

1. Locate and correct all leaks (see Checking Gas Connec- tions, page 14).

2. Contact customer service.

1. Refer to Air for Combus- tion and Ventilation requirements, page 7.

www.usaprocom.com

200102-01A26

REPLACEMENT PARTS

Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement parts, call Customer Service toll free at 1-866-573-0674 for referral information.

When calling Customer Service or your dealer, have ready:

• Your name

• Your address

• Model and serial number of your heater

• How heater was malfunctioning

• Type of gas used (Propane/LP or Natural gas/NG)

• Purchase date

• Usually, we will ask you to return the defective part to the factory

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s) call Customer Service toll free at 1-866-573-0674 for referral information.

When calling Customer Service have ready:

• Model number of your heater

• The replacement part number

ACCESSORIES

Purchase these heater accessories from your local dealer. If they can not supply these accessories, contact ProCom Heating, Inc. at 1-866-573-0674 for information.

EQUIPMENT SHUTOFF VALVE

For all models. Equipment shutoff valve with 1/8" NPT tap.

SERVICE HINTS

• pilot will not stay lit

• burners will have delayed ignition

• replace will not produce specied heat

• propane/LP gas supply might be low (propane/LP units only) You may feel your gas pressure is too low. If so, contact your local gas supplier.

When Gas Pressure Is Too Low

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. If so, contact ProCom Heating, Inc. at 1-866-573-0674.

When calling, please have your model and serial numbers of your heater ready.

www.usaprocom.com

27200102-01A

PARTS

11

MODELS FBD400RT

21

1

5

19

3

4

PILOT

OFF

7

2

ON

18

14

LEARN

ON

REMOTE

OFF

15

20

6

TEMP

8

9

10

16

17

12

13

www.usaprocom.com

200102-01A28

PARTS

MODELS FBD400RT

This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 27 of this manual.

ITEM

10 HL043-01

12 HL045-01 Log 5 1

13 HL045-02 Log 6 1

14 YDF06 Fuel Selection Device Assembly 1

15 MDL304B Fuel Selection Device Knob 1

16 RG04-1M Receiver 1

17 RG04-1T Remote Control 1

18 MRT-01 Control Valve 1

19 ML073-04 Ignitor Cable 1

20 PF120820 Regulator Plug 2

21 BL016-07-01 Blower Access Panel 1

FBD400RT-A DESCRIPTION

1 FHL008-02D Hood 1

2 FBB102 Louver 1

3 FBB104BL Left Door Assembly 1

4 FBB104BR Right Door Assembly 1

5 NDD308-400 ODS Pilot 1

6 RV83FI-4/9 Regulator 1

7 PIMSC1-01 Ignitor 1

8 HL041-01 Log 1 1

9 HL042-01 Log 2 1

Log 3

11 HL044-01 Log 4 1

PARTS AVAILABLE - NOT SHOWN

HP007 Hardware Package 1

ML064-01 Accessory Set 1

PCAM-012 AAA Battery 1/3

PCAM-018 AA Battery 4

FB28D20 Hex Wrench 1

QTY

1

www.usaprocom.com

29200102-01A

NOTES

________________________________________________________________________

www.usaprocom.com

200102-01A30

NOTES

________________________________________________________________________

www.usaprocom.com

31200102-01A

WARRANTY

KEEP THIS WARRANTY

Model _______________________________

Serial No. ____________________________

Date Purchased _______________________

Keep receipt for warranty verication.

REGISTER YOUR PRODUCT AT WWW.USAPROCOM.COM

IMPORTANT: We urge you to register your product within 10 days of date of installation, complete with entire serial number which can be found on the rating plate. Please ll out the warranty information above for your personal records. Retain this manual for future reference.

Always specify model and serial numbers when communicating with customer service.

We reserve the right to amend these specications at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

ProCom Heating, Inc. warrants this product to be free from defects in materials and components for TWO (2) years from the date of rst purchase, provided that the product has been properly installed by a qualied installer in accordance with all local codes and instructions furnished with the unit, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty, the Bill of Sale or cancelled check must be presented.

RESPONSIBILITY OF OWNER

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating condition. Warranty part(s) MUST be obtained through ProCom Heating, Inc. who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualied installer in accordance with all local codes and instructions furnished with the unit.

WHAT IS NOT COVERED

This warranty does not apply to parts that are not in original condition because of normal wear and tear or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT, THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES. INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE. PROCOM HEATING, INC.'S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND PROCOM HEATING, INC. SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT. INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of accidental or consequential damages, the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specic legal right, and you may also have other rights that vary from state to state.

ProCom Heating, Inc. Bowling Green, KY 42101 www.usaprocom.com 1-866-573-0674

200102-01 Rev. A 04/14