Dukane 8965WUSS User Manual

User's Manual

Projector

8965WUSS

Thank you for purchasing this product. Please read this manual before using the product. Store it for future reference.

USS-user-manual-00

8965W

INDEX

Warning, Notices and Safety Instructions 4

Projector parts and functions 17

Front view 17

LED Indicator 17

Rear view 18

Projector keypad 18

I/O Port (Input / Output) 19

Bottom view 20

Remote control 21

Range of effective remote control signal reception 23 Installing batteries in the remote control 23

Projector installation 25

Throw distance 25

Modes of installation 25

Projection 25

Horizontal and vertical lens shift 27

Lens shift 27

Moving the lens vertically 29

Moving the lens horizontally 29

Connecting the projector 30

HDMI / MHL / DVI connection 30

RGB connection 31

HDBaseT connection 32

RJ45 connection 33

USB POWER (5V/1.5A) connection 33

3D SYNC connection 34

VIDEO connection 34

SERVICE connection 35

RS232C connection 35

Audio IN (L/R) connection 36

Audio OUT (Mini jack) connection 36

Audio IN (Mini jack) connection 37

Powering the projector on or off 38

Powering on the projector 38

Connect the power cord to the projector 38

Turning off the projector 38

Selecting an input source 39 Setting an access password (security lock) 40 Choosing a location 42 Adjusting the projector's angle 43 Adjusting the projector’s zoom and focus 43

Zoom 43

Focus 44

Correcting keystone 45

OSD menu tree 46

OSD description 50

Image 50

Display Mode 50

Brightness 51

Contrast 51

Computer 52

Auto Image 53

Advanced 53

Color Manager 55

Settings 1 56

Source 56

Projection 56

Aspect Ratio 57

Keystone 57

Digital Zoom 57

Audio 57

Advanced 1 58

Advanced 2 59

4 Corner 59

Settings 2 60

Auto Source 60

No Signal Power Off 60

Auto Power On 60

Laser Mode 60

Reset All 61

Stat us 61

Advanced 1 61

Advanced 2 70

Custom Light 70

Cleaning 71

Cleaning the cabinet 71 Cleaning the lens 71

Using the Kensington® lock 72

Simple troubleshooting 73

LED status 74

Specications 76

Supported signal input modes 77 MHL timing format 79 3D timing format 79 Dimensions 80

English-2

Communication settings 81

RS-232 communication 81

Connection 81

Command control via the network 83

Connection 83

Communication port 83

Command control settings 84

Communication command table 84 PJLink command 96 Projection distance vs projection size table 97

Trademark 98

Warranty and after-service 98

English-3

Warning, Notices and Safety Instructions

Notice

This product is intended for the adults who have the ability to operate this machine.

Please write down your projector model number and serial number and keep the information for maintenance purposes in the future. Should the equipment be lost or stolen, the information could also be used for the police report.

Model number: Serial number:

Please check the accessories that come with the projector with the following list. Should you nd any

missing accessory, contact your dealer immediately.

1. AC Power Cord

2. Remote control

3. AAA battery 2pcs

Do not open

4. RGB c

5. 3D Sync cable 1pcs

able

About Electro-Magnetic Interference

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts.

Description pertaining to FCC Rules Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. Operation of this equipment in a residential area is likely to cause harmful interference in which case.

English-4

Warning, Notices and Safety Instructions

The user will be required to correct the interference at his own expense.

Caution: Changes or modications not expressly approved by the manufacturer void the user’s

authority to operate the equipment.

CAN ICES-3(A) / NMB-3(A)

Information for users applicable in European Union countries

Disposal of Old Equipment and Batteries Only for European Union and countries with recycling systems

The above mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries as unsorted municipal waste, but use the return and collection systems available. If the batteries or accumulators included with this equipment display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury, or more than 0.002% Cadmium or more than 0.004% Lead.

Note for the battery symbol (bottom symbol):

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

Sun light Warning

Avoid using this projector in direct sun light. Sunlight may cause serious damage to the digital mirror device (DMD™) at the back of the projector

lens.

Never look into the projector light source directly

When turn on the projector, make sure nobody's eye will effects by the projection of light.

Always avoid to let eyes contact to the light. As with any bright source, do not stare into the direct beam, RG2 IEC 62471-

5:2015.

Key any object away from concentrated projection light beam

Blocking the beam by something causes high temperature and could result in

re or smoke.

English-5

Warning, Notices and Safety Instructions

Electric shock

To protect your projector, avoid turning on the projector during lightning storms and unplug it from the wall outlet. This will prevent sudden electrical surges caused by the lightning from damaging the projector.

Do not overload wall outlets/extension cords

Pay attention to the current load of the outlet and cord you are using to prevent re or electrical shock.

Cleaning

When cleaning the projector, be sure to unplug it from the wall outlet to prevent electric shock. Do not use liquid or aerosol cleaners. Use a dry/damp cloth with excessive moisture removed for

cleaning. Be sure to use cleaning cloth designed to clean monitors for the projector to prevent damages to the projector casing due to abrasion.

Dampness, smoke, steam, dust, high temperature and direct exposure to sunlight

Do not operate the projector in environments where it could be expose to dampness, smoke, steam, dust, high temperature or direct sunlight. For example: bathroom, kitchen, adjacent to washing machine, damp basement rooms, electric heaters or similar environments. Keeping or operating the projector in the above-mentioned environment could lead to discoloration, mold formation, grease or damages to the projector.

Do not place the projector where any oils, such as cooking or machine oil, are used. Oil may harm the product, resulting in malfunction, or falling from the mounted position. Do not use adhesive such as threadlocker, lubricant and so on.

Ventilation

The projector case is designed with slots and openings to remove the heat inside the projector so that it will not overheat and damage the components. Be sure to operate the projector in an environment with ideal ventilation and don't operate it on a sofa, rug or other closed-in environments that could obstruct ventilation.

Intrusion of foreign objects

Be sure to keep all foreign objects away from entering the projector because it could be exposed to

hazardous voltages and cause parts to short circuit. This could in turn lead to re hazard or electric

shock. Examples of foreign objects include: cockroach, screws, liquid and so forth. In addition, never spill liquid into the projector.

Carrying the projector

The projector net weight is approximately 11.4 kg . When moving the projector on a cart, be sure to handle the cart with care as abrupt stops, jolts of excessive force or uneven ground could lead the projector to topple.

English-6

Warning, Notices and Safety Instructions

Please install the projector on an even and stable surface

Avoid placing the projector on unstable cart, tripod, table and so forth to prevent the projector from falling, becoming damaged or causing injuries.

Servicing

Should you encounter problem with the projector, please seek assistance from your local dealer or

qualied service personnel. Do not attempt to service the projector by yourself so that you would not

be exposed to high voltage or other potential hazards.

No service is allowed except by authorized personnel.

Should you encounter any of the following situation, please unplug your projector from the wall outlet

and contact a qualied service personnel for assistance:

• Damaged power cord or power plug.

• If a foreign object has fallen into the projector or if you have spilled water or other liquid into the projector.

• If the projector has been dropped accidentally or damaged.

• If you experience noticeably poor performance or malfunctioning with the projector despite having followed instructions for normal operation.

Changing parts

Should any part of the projector be damaged, check with your servicing personnel that only

manufacturer certied parts were used for replacement. Used of non-certied parts may result in damages to the projector or hazards such as re or electric shock. After changing parts, be sure to

remind the servicing personnel to perform safety inspections to ensure that the projector operates nor m ally.

No maintenance allowed by end user, Do not open the cabinet. No user serviceable part inside.

English-7

Warning, Notices and Safety Instructions

Power cord

Don't place the projector where the cord can be walked on. This may result in fraying or damage to the power cord, especially at the plug and the point of connection between the power cord and the projector.

Please use the power cord that comes with the projector or the type of power cord specied for

the projector (refer to the descriptions printed on the power cord). If you are not sure of the power available at the region you are in, consult your local power company to prevent damages to the

projector due to the use of wrong power cord or potential re hazards due to current overload.

Depending on the country and region you are in, the voltage and type of socket of the wall outlet may

be different from the projector. If you are unable to t the power plug into the wall outlet, contact your local dealer and do not remove the extra pin on the power plug to forcibly t it to the socket at the risk

of your own safety. Connect the ground terminal for the AC inlet of this unit to the ground terminal of the building using

an appropriate power cord (bundled).

Install the projector where you can access the power outlet easily.

Safety mark

ENGLISH FRANÇAIS DEUTSCH ES PAÑO L PORTUGUÊS

Descriptions of the symbols displayed on the projector

Alternating Current Courant Alternatif Wechselstrom Corriente alterna Corrente alternada

Les descriptions de ces

symboles sont afchées

sur le projecteur

Beschreibungen der am Projektor angezeigten Symbole

Descripciones de los símbolos mostrados en el proyector

Descrições dos símbolos apresentados no projector

Standby (Power) Veille (Alimentation)

On (Power) Marche (Alimentation) Ein (Stromversorgung) Encendido (Alimentación) Ligado (Alimentação)

Off (Power) Arrêt (Alimentation) Aus (Stromversorgung) Apagado (Alimentación) Desligue (Alimentação)

WARNING / CAUTION

HIGH TEMPERATURE

HI GH VOLTAGE HAUTE TENSION HOCHSPANNUNG ALT O VOLTA JE VOLTAGEM ALTA

HIGH PRESSURE HAU TE PRESSION HOCHDRUCK ALTA P RESIÓN PR ESSÃO A LTA

PROJECTOR NOT FOR CONSUMER USE

OPTICAL R ADIATION WARNING

Kensington Kensington Kensington Kensington Kensington

AVERTISSEMENT / ATTENTION

HAU TE TEMPERATURE

PROJECTEUR DESTINÉ À UN USAGE PROFESSION NEL

ATTENTION RAYON NEM ENT LASER

Bereitschaft (Stromversorgung)

WARNUNG / VORSICH T

HOHE TEMPERATUR ALTA TEMPERATURA TEMPERATURA ALTA

PROJEKTOR NICHT FÜR DEN PRIVATEN GEBRAUCH

WARNUNG! OPTISCHE STRA HLUNG

En espera (Alimentación) Em espera (Alimentação)

ADVERTENCIA / PRECAUCIÓN

PROYECTOR NO DESTINADO A USO POR PARTE DE CONSUMIDORES

ADVERTENCIA SOBRE LA RADIACIÓN ÓPTICA

AVISO / PRECAUÇÃO

PROJECTOR NÃO DESTINADO AO USO DE CONSUMIDORES

AVISO DE RADIAÇÃO ÓPTICA

English-8

MERCU RY CONTAINED

CONTIENT DU MERCUR E

QUECKSILBERHALTIG CONTIEN E MERCURIO CONTÉM MERCÚRIO

Warning, Notices and Safety Instructions

ENGLISH FRANÇAIS DEUTSCH ES PAÑO L PORTUGUÊS

Descriptions of the symbols displayed on the projector

RG2 caution ATTENT ION: RG2 Achtung! RG2 Precaución sobre RG2 Atenção RG2

Les descriptions de ces

symboles sont afchées

sur le projecteur

Beschreibungen der am Projektor angezeigten Symbole

Descripciones de los símbolos mostrados en el proyector

Descrições dos símbolos apresentados no projector

DO NOT LOOK INTO THE BEAM

DO NOT SHADE THE LIGHT

Lase r Wa rni ng

中文 한국어

投影机上显示的标志符号说明

交流电 교류 전류

待机（电源） 스탠바이(전원)

开启（电源） 온(전원)

关闭（电源） 끄기 (전원)

警告 / 注意事项 경고 / 주의

小心高温 고온 주의

小心触电 감전 주의

NE PAS REGARDER DANS LE FAISCEAU

NE PAS COUVR IR LA LUMIÈRE

Avertissement Relatif au Laser

프로젝터에 표시되 어 있는 기호에 대 한 설명

NICHT IN DEN STRAHL BLICKEN

LICHTWEG NICHT BLOCKIEREN

Warnhinweis zum Laser

РУСС КИЙ

Описания символов, отображаемых на проекторе

Переменный ток

Ожидание (питание)

Включено (питание)

выключено (питание)

ПРЕДУПРЕЖДЕНИЕ / ВНИМАНИЕ

ВЫСОКАЯ ТЕМ ПЕРАТУРА

ВЫСОКОЕ НАПРЯЖЕНИЕ

NO MIRE AL HAZ

NO TAPE LA LUZ NÃO BLOQUEIE A LUZ

Advertencia Relacionada con el Láser

日本語

機器上に表示しているシンボル説明

交流電流

スタンバイ（電源）

オン(電源)

オフ (電源)

注意 / 警告

高温注意

感電注意

NÃO OLHE PARA O FEIXE

Aviso Relativo ao Laser

小心破裂 파열 주의

该投影机非普通消费者使用

光辐射警告 광 방사 경고

Kensington Kensington

含水银 수은 함유

小心RG2 RG2 주의

禁止直视光束

小心不要遮挡投影机发出的光

激光警告 레이저 경고

비소비자용 프로젝 터

빔을 들여다 보지 마십시오

램프를 가리지 마십시오

ВЫСОКОЕ ДАВЛЕНИЕ

ПРОЕКТОР НЕ ПРЕДНАЗНАЧЕН ДЛЯ ПОТРЕБИТЕЛЬСКОГО ИСПОЛЬЗОВАНИ Я

ПРЕДУПРЕЖДЕНИЕ ОБ ОПТИЧЕСКОМ ИЗЛУЧЕНИИ

Kensington

РТУТОСОД ЕРЖАЩИЙ

Внимание RG2

НЕ СМОТРИТЕ НА ЛУЧ

НЕ ЗАТЕНЯЙТЕ СВЕТ

Предупреждение o Лазерноем Излучении

破裂注意

民生用では無い機器

光放射警告

Kensington

水銀含有

RG2 注意 (覗き込み禁止)

覗き込み禁止

光を遮るな注意

レーザーに関する警告

English-9

Warning, Notices and Safety Instructions

Notices you should read prior to the installation of the projector

Take frequent breaks to let your eyes rest

Prolonged viewing of the projector screen could strain your eyes. Please be sure to rest your eyes ade quately.

Installation environment for the projector

You should avoid installing the projector at place of excessive dampness, dust or smoke. If installation in such environment is unavoidable, be sure to have the interior of the projector.

Cleaned routinely to prolong the projector's lifecycle. Cleaning of the projector's interior should only

be performed by qualied service personnel dispatched by your local dealer and you should not

attempt to clean the inside of the projector by yourself. If other light source is directly projected onto the projector screen, the color of the picture from the

projector will appear to be pale and the picture quality will be lower. In addition, your eyes would be more prone to fatigue. Therefore, it is recommended that the projector be installed in places without direct exposure to sunlight or other sources of intense light.

The ideal operating temperature range for the projector is between 0°C ~ 40°C (32°F ~ 104°F) The ideal storage temperature range for the projector is between -20°C~ 60°C (4°F ~ 140°F)

Congurationsforprojectoroperationathighaltitudes

When operating the projector at higher altitudes, be sure to manually set the fan mode to "High" or

it could shorten the life of the optical system in the projector. High altitude is dened as places being

1520 meters (5000 feet) or higher. Please refer to Page 62 and Page 76.

Protect the projector with care

When placing the projector at a high position, be sure to secure the projector rmly so that it would

not fall and cause injuries. Take care to protect the projector's lens from collision, abrasion or other damages. Be sure to close the lens cover or cover the projector with a dust cover if you need to store the projector or if it will not be used for an extended time.

Keep the projector's ventilation inlets and outlets free from obstructions

Note the direction of air ow at the designated spot of installation. Do not let the hot air released from the outlet ow back to the inlet as it will prevent proper cooling and lead to damage of the projector's

internal structure. In the event of high temperature due to malfunctioning of the internal cooling fan caused by clogging

at the ventilation inlets and outlets, the projector will activate its automatic protection mode and shutdown. When this happens, it does not necessary mean that the equipment is malfunctioning. Try to unplug the power cord from the wall outlet and wait for approximately 15 minutes before operating the projector again (remember to remove the objects that have caused poor ventilation so that the projector will not go into the protection mode again).

English-10

Warning, Notices and Safety Instructions

Description: The regulation of temperature inside the projector by the cooling fan is automatic. And as such, the sound of cooling fan changing its operating speed does not imply that a problem has occurred with the projector.

Positioning precautions

This projector can be installed 360° range. But life of optical parts will be shorten as portrait situation:

English-11

Warning, Notices and Safety Instructions

Caution for 3D

• Don't let children view the 3D by themselves , please always be accompanied by an adult.

• Although more than six years old can view the 3D. But children may not tell you if they are feeling unwell when viewing 3D content, so always be sure to check with the child.

• When viewing 3D content, be sure you are at an appropriate distance from the front of the screen. Suggest keep at least three times the height of the screen away from the screen.

• Check that the settings are correct and that the 3D effect is being correctly applied. If the image is inversed and the left and right eye images are swapped, the 3D effect does not work, which could cause eye strain or cause you to feel unwell.

3D content not suitable for below situation, it could aggravate their pre-existing conditions.

• People with a history of photosensitive epilepsy.

• People has heart disease.

• Pregnant women.

• People with serious illnesses.

• People with a history of epileptic seizures.

Suggest stop to view the 3D, if has below situation:

• When you feel unwell , tired, sleep deprived, fatigued or inebriated.

• The 3D image doubled or not clear.

• Enjoying 3D content that rotates, rolls, or shakes, some person may feel they are moving and trigger a form of “sea sickness”.

• Take too long time for viewing 3D content, be sure to take regular breaks to avoid cause eyestrain.

English-12

LASER WARNING

This symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely followed.

CLASS 3R LASER PRODUCT

This Laser Product is designated as Class 3R during all procedures of operation. LASER LIGHT - AVOID DIRECT EYE EXPOSURE.

Do not point laser or allow laser light to be directed or reected toward other people or reective objects.

Direct or scattered light can be hazardous to eyes and skin. There is a potential hazard of eye exposure to laser radiation if the included instructions

are not followed. Caution – use of controls or adjustments or performance of procedures other than those

specied herein may result in hazardous radiation exposure.

Laser parameters

Warning, Notices and Safety Instructions

Wavelength Mode of operation Pulse width Pulse repetition rate Maximum laser energy Total internal power Apparent source size Divergence

450nm - 460nm (Blue) Pulsed, due to frame rate

1.34ms 120Hz

0.698mJ >100W >10mm, at lens stop >100 mili Radian

English-13

Warning, Notices and Safety Instructions

Product labels

Below drawing show the label's location.

a. Serial No. b. MAC Label

English-14

Warning, Notices and Safety Instructions

a. Hazard Warning Symbol b. Aperture Label

c. Certication Statement Label

d. Explanatory Label

English-15

Warning, Notices and Safety Instructions

Location of laser aperture

Following drawing shows the laser aperture location. Be careful not to see the light directly.

Interlock switches

This machine has interlock switches to protect the laser light leakage.

Switch will power-off the system when the Top cover is opened.

Note: The Dukane model described in this document is manufactured by

Hitachi and uses the same rmware, software programs, control code, and accessory parts. The equivalent Dukane to Hitachi models is 8965WUSS (LP-WU6500).

English-16

Projector parts and functions

Front view

Projector parts and functions

1. LENS SHIFT

Adjust the projected image position.

2. Ventilation outlet

The hot air generated inside the projector is dispersed through the ventilation slot. Make sure the ventilation slot is free from obstruction.

3. Zoom

Zoom in or zoom out the projected image

4. Infrared receiver

5. Adjustable foot

Adjust the height and angle of the projector with the adjustable foot.

LED Indicator

1. POWER

The indicator shows the power status. The indicator lights when the projector is

in standby state. The indicator blinks once every 5 seconds when the projector is an ON state.

6. LED Indicator

7. Projector keypad

8. Ventilation inlet

The internal cooling fan draws cool air from the ventilation inlet into the projector.

9. Speaker

10. Focus

Adjust the projected image’s focus.

11. Lens

2. LIGHT

The indicator shows the light source and system error status.

3. T EMP.

The indicator shows the thermal error message.

English-17

Projector parts and functions

Rear view

1. I/O port

2. Power inlet

3. Infrared sensor

4. Security bar

Projector keypad

1. ▲/

Use this button to make your selection

or congure, adjust conguration on the

menu. Keystone can be adjusted when no other

menu is displayed.

2. AUTO

Auto adjust the signal synchronization.

3. ◄/

Use this button to make your selection

or congure, adjust conguration on the

menu. Keystone can be adjusted when no other

menu is displayed.

Press to turn on or off the projector.

5. ▼/

Use this button to make your selection

or congure, adjust conguration on the

menu. Keystone can be adjusted when no other

menu is displayed.

5. Speaker

6. Ventilation outlet

7. Kensington® lock

6. ENTER

Press to select items in the menu or

conrm the settings you have changed.

7. SOURCE

Select input signal source.

8. ►/ Use this button to make your selection

or congure, adjust conguration on the

menu. Keystone can be adjusted when no other

menu is displayed.

9. MENU Displays or hides the menu.

English-18

I/O Port (Input / Output)

Projector parts and functions

1. HDMI 1 (Digital audio/video connector)

Connect to HDMI or DVI source.

2. RJ45

Connect a LAN cable from Ethernet.

3. HDMI 2 (Digital audio/video connector)

Connect to HDMI or DVI source.

4. HDBaseT (RJ- 45 jack)

Connect to HDBaseT source via LAN cable.

5. HDMI 3 / MHL (Digital audio/video

connector) Connect to a HDMI or MHL-compatible

device.

6. MONITOR OUT (D-sub 15-pin mini

shrink jack) Connect to a monitor. Loop through only for COMPUTER.

7. COMPUTER (D-sub 15-pin mini shrink

jack) Connect to a PC.(Support RGB and

component video signal input).

8. VIDEO (RCA jack)

Connect to the composite video device.

9. 3D SYNC (VESA 3-pin)

Connect to 3D IR glasses receiver unit.

10. SERVICE

For service personnel only.

11. USB POWER (USB A type jack)

Connect a USB device. (Support 5V/1.5A output while the projector Power On.)

12. AC Connect a POWER cable.

13. RS-232C (9-pin D-sub socket) (Cross cable)

Connect your PC or system control equipment.

14. AUDIO OUT (3.5 mm, mini jack)

Connector to an audio amplier device.

15. AUDIO IN (3.5 mm, mini jack) Connect an audio source input. (Available

for Computer, BNC, DVI-D source.)

16. AUDIO IN (L/R) (RCA jack) Connect an audio source. (Available for

Video signal input.)

English-19

Projector parts and functions

Bottom view

135.0 135.0

130.0 160.0

English-20

Remote control

1. IR transmitter

2. ON

This button is used to turn on the projector.

3. PC

Displays the VGA (COMPTER IN) / BNC (R/B/G/H/V) source selection (toggle).

4. HDMI

Displays the HDMI 1/HDMI 2/DVI source selection (toggle).

5. H DBaseT

Displays the HDBaseT source selection.

6. USB

Not available for this projector.

7. ▲/ Use this button to make your selection

or congure, adjust conguration on the

menu. Keystone can be adjusted when no other

menu is displayed.

8. MENU Displays or hides the menu.

9. (ENTER)

Press to select items in the menu or conrm

the settings you have changed.

10. ◄/ Use this button to make your selection

or congure, adjust conguration on the

menu. Keystone can be adjusted when no other

menu is displayed.

11. ▼/ Use this button to make your selection

or congure, adjust conguration on the

menu. Keystone can be adjusted when no other

menu is displayed.

12. Keystone Press to open keystone adjustment menu.

13. Play or pause video/music for MHL.

14. Play the previous item on the programming

list for MHL.

15. Stop video/music playing for MHL.

16. Reverse in set increments for MHL.

English-21

Remote control

17. Source

Select input source. Combo key function for Remote Control ID

settings (Press ID button + Number for 3 seconds).

18. Auto / 0

This button is used to Resync the picture; when the picture signal becomes unstable or picture quality deteriorates simply press this button and the projector will automatically adjust the screen dimension, phase, timing and so forth.

Number for Remote ID setting used.

19. Brightness

Displays the brightness setting bar.

20. Contrast / 2

Displays the Contrast settings bar. Number for Remote ID setting used.

21. Light

Displays the light power adjustment menu.

22. Zoom / 4

Displays the digital zoom settings bar. Number for Remote ID setting used.

23. Freeze

Freeze/unfreeze the picture on the screen.

24. Blank / 6

Makes the screen blank. Number for Remote ID setting used.

25. STANDBY

This button is used to turn off the projector.

26. Video / S-Video

Displays the Video source selection.

27. Network

Open the Network menu.

28. EXIT

Press this button to exit menu or return to previous menu level.

29. ►/ Use this button to make your selection or

congure, adjust conguration on the menu.

Keystone can be adjusted when no other menu is displayed.

30. MHL Change MHL / Projector mode.

31. Play the following item on the programming

list for MHL.

32. Forward in set increments for MHL.

33. Volume / 1 Displays the Volume setting bar. Number for Remote ID setting used.

34. Mute /3 Mutes the built-in speaker. Number for Remote ID setting used.

35. 3D / 5 Open the 3D Setting menu. Number for Remote ID setting used.

36. Status / 7 Opens the Status menu (the menu only

opens when an input device is detected). Number for Remote ID setting used.

Note:

Remote Combo Key Settings: ID+0: Reset Remote Control ID to default settings. ID+1: Set Remote Control ID to "1".

ID+7: Set Remote Control ID to "7". Projector also need setting ID for unique control. Refer to Page 62 : "Remote ID".

Note: When the projector is under MHL

mode, the keypad on projector should be same denition of the key on remote control. With MHL function: MENU for App settings, ▲ Up, ▼ Down, ◄ Left and ► Right are used as directional arrows, also included

ENTER and EXIT. Controlling your smart device with the remote control:

When the projector displays the content from your MHL compatible smart device, you can use the remote control to control your smart device. To enter the MHL mode, the following buttons are available for controlling your smart device, Arrow keys (▲ Up, ▼ Down, ◄ Left, ► Right), MENU, EXIT, MHL control buttons.

English-22

Remote control

Range of effective remote control signal reception

The diagram below illustrates the range of effective remote control signal reception (Unused new battery).

Note: Avoid placing the remote control at places of high temperature or humidity as it could

cause the remote control to malfunction.

Note: If the infrared receiver is exposed to uorescent lamp or strong sunlight, the remote

control may not operate normally.

Installing batteries in the remote control

1. Remove the cover by sliding it in the direction indicated by the arrow.

2. Insert two new AAA batteries (check the polarity).

3. Replace the cover.

Note: Always handle the batteries with care and use them only as directed. Improper use may

result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding.

Note: Keep a battery away from children and pets.

English-23

Remote control

Note: Do not recharge, short circuit, solder or disassemble a battery.

Note: Be sure to insert the batteries in the corresponding orientations to match the polarities.

Note: Do not mix new battery with used one as it would shorten the life of new one or cause

leakage.

Note: Use AAA batteries as instructed; do not attempt to insert different types of batteries into

the remote control.

Note: If you will not use the remote control for long period, remove the batteries from the remote

control and store them in a safe place.

Note: The liquid contents in the batteries is harmful to the skin; do not touch the leakage with

your bare hands directly. When installing fresh batteries, be sure to clean up the leakage thoroughly.

Note: If the range of effective remote control signal reception decreases or if the remote control

stops working, replace the batteries.

Note: Refer to the regulations enforced by your local government on the disposal of used

batteries; improper disposal could damage the environment.

Caution: RISK OF THE EXPLOSION IF BATTERY IS REPLACED BY ANY INCORRECT

TYPE.

Caution: DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

English-24

Projector installation

Throw distance

Throw Distance (TD) = Screen Width (W) x Throw Ratio (TR)

Projector offers the following throw ratios:

• 1.15~1.9 : 1, 36.7~201.9inch

Modes of installation

• Install the projector in an environment from 0°C (32°F) to 40°C (104°F). The projector should be kept away from sources of heat and / or ventilation openings of air conditioner.

Note: The temperature also depends on altitude. Please refer to Page 62 and Page 76.

• The projector should be kept away from devices that emit electromagnetic energy, such as motors or transformers. Common devices that emit electromagnetic energy include slideshow system,

speakers, power ampliers and elevators.

• If you choose to install the projector from the ceiling, be sure to use the ceiling installation

components veried safety. For details, please contact your local dealer.

Projection

Normal

Advantages: easy to install can be easily moved

or adjusted easy to operate.

Disadvantage: occupies oor space and limits

seating capacity.

English-25

Projector installation

Ceiling

Refer to Page 42 : “Ceiling”

Advantage: does not occupy oor space does not

draw attention to it. Eliminates the possibility that someone would accidentally move the projector.

Disadvantage: stricter installation requirements

and conditions; care should be taken during the installation to ensure the projector has been securely mounted. Operation of the projector becomes inconvenient without the remote control.

Rear

Refer to Page 42 : “Rear” Advantage: the projector is completely hidden

from plain view the projector can be easily operated this setup usually offers better reduction of ambient noise.

Disadvantage: requires an additional room for

installation relatively higher costs for installation.

Rear + Ceiling

Refer to Page 43 : “Rear + Ceiling” Advantage: the projector is completely hidden

from plain view this setup usually offers better reduction of ambient noise.

Disadvantage: requires an additional room for

installation. Stricter installation requirements and conditions; care should be taken during the installation to ensure the projector has been securely mounted. Operation of the projector becomes inconvenient without the remote control.

Rear with a Mirror

If you wish to have a rear projection setup with limited space to the rear of the projector, you can

use a mirror to reect the light path.

However, both the projector and the mirror have to be precisely located. If you are considering such installation, please contact your dealer for assistance.

Advantage: the projector is completely hidden

from plain view this setup usually offers better reduction of ambient noise.

Disadvantage: requires an additional room for

installation relatively higher costs for installation.

English-26

Projector installation

Horizontal and vertical lens shift

In addition to using the adjustable feet to adjust projection angle, you can also use the Lens Shift function to adjust the projected picture.

Lens shift

1. Turn the VERTICAL adjuster fully counter clockwise. Then turn it clockwise and adjust the

vertical lens position upward.

2. Turn the HORIZONTAL adjuster clockwise or counter clockwise to adjust the horizontal lens

position.

Note for adjusting the lens shift

1. Adjust the lens shift / zoom / focus after 30 minutes since the projector was turned on.

2. Slight changes of the image position and/or focus may occur within 30 minutes after the

projector was turned on. If the room temperature and humidity have changed after adjusting the lens shift / zoom / focus, readjust them as necessary.

3. Set the image size including the margin from the screen edge in anticipation of the changes

after installation.

4. When adjusting the lens shift vertically, nish adjusting lens shift by moving the projected

screen upward. If you nish adjusting the lens shift by moving the projected screen downward,

the projected screen may be misaligned slightly downward over time.

English-27

Projector installation

Note for adjusting the lens shift

1. You can feel the rotational resistance of the lens adjuster increasing if the lens shift exceed its

range. Do not turn the lens adjuster further. If the lens adjuster is turned excessively, it runs idle by a clutch mechanism inside the adjuster. Although it makes a clicking sound, it is not a malfunction. Turn the lens adjuster to the opposite direction to adjust the lens shift.

2. Keep turning the lens adjuster while pressing it downward if the adjuster is turned to the

opposite direction with a clicking sound and the lens shift does not work after the adjuster has been turned exceeding the lens shift range. You need to turn the lens adjuster for a while until the lens shift starts.

3. Do not turn the lens adjuster while pressing it downward out of the lens shift range. The lens

shift may be locked because a clutch mechanism does not work. In such a case, keep turning the lens adjuster while pressing it downward like in step2.

4. When adjusting the lens shift to the maximal oblique direction, the periphery of the projected

screen may be dark or a shadow may be cast.

Caution: Operate the lens adjusters gently as the lens may malfuction when subjected to shocks.

English-28

Projector installation

Moving the lens vertically

The distance of vertical lens movement is 12% of the screen height directions (The offset range is about 63% to 75%). For instance, if you are using a 2.15m × 1.35m (100”) screen, you will be able to move the picture upwards no more than 13.5cm(10%) and downwards no more than 2.7cm(2%) from

default position. (Please conrm the default position in Page 97 ).

This illustration shows normal vertical lens shift without the use of special specication lens or

projector.

Note: Please make sure the center of lens is rectangular to the center of the screen.

Moving the lens horizontally

The distance of horizontal lens movement is 2.5% of the screen width in both directions. For instance, if you are using a 2.15m × 1.35m (100”) screen, you will be able to move the picture left or right by no more than 5.4cm.

This illustration shows normal horizontal lens shift without the use of special specication lens or

projector.

Note: Please make sure the center of lens is rectangular to the center of the screen.

Note: Although the lens shift position can be moved beyond the specication, please use it in the

position within the specication. When used at a position outside specications, the corner of the screen becomes shade or color unevenness becomes large, and sufcient optical performance can not be obtained.

English-29

Projector installation

Connecting the projector

HDMI / MHL / DVI connection

Signals from picture source offer the best projection picture quality when sent through HDMI/DVI. Therefore, try to use input devices with HDMI/DVI output as the source of picture.

English-30

+ 68 hidden pages