Dukane 8950WU User Manual

LCD Projector

8945WU / 8950WU

User's Manual (detailed) Operating Guide

Th a n k y o u f o r p u r c h a s i n g t h i s p r o j e c t o r .

WARNING

►Before using this product, please read all manuals for this product. Be sure to read S a f e t y G u i d e rst. After reading them, store them in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING

CAUTION

NOTICE This entry notices of fear of causing trouble.

NOTE

• The information in this manual is subject to change without notice.

• The illustrations in this manual are for illustrative purposes. They may differ slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Tr a d e m a r k a c k n o w l e d g m e n t

• VESA and DDC are trademarks of the Video Electronics Standard Association.

• Mac

, OS X® and macOS® are registered trademarks of Apple Inc. in the U.S. and/or

other countries.

•

HDMITM, the HDMI logo, and High-Denition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC in the United States and other countries.

• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.

• DICOM for its standards publications relating to digital communications of medical information.

• trademarks of MHL, LLC in the United States and other countries.

All other trademarks are the properties of their respective owners.

is the registered trademark of the National Electrical Manufacturers Association

MHL®, the MHL logo, and Mobile High-Denition Link are trademarks or registered

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



8945WU_8950WU_User_anual-00

Contents



Introduction ............... 3

Features ......................3

Checking the contents of package

Part names ....................4

Projector, Control panel, Ports, Remote control

Setting up ................. 7

Arrangement ...................7

Connecting with your devices Connecting to a power supply Fastening the cable

.............1 5

Fastening the adapter cover ......

Using the security bar and slot ....1 6

Remote control ............ 17

Installing the batteries ...........1 7

About the remote control signal ...1 8 Changing the frequency of remote

control signal ..................1 8

Using as a simple PC mouse & keyboard

Power on/off .............. 20

Turning on the power ...........2 0

Turning off the power ...........2 1

Operating ................ 22

Adjusting the volume ............2 2

Temporarily muting the sound .....2 2

Selecting an input signal .........2 3

Selecting an aspect ratio .........2 3

Adjusting the projector's elevator

Adjusting the zoom and focus .....2 4

Using the automatic adjustment feature

Correcting the distortion ......... 2 6

Using the magnify feature ........2 9

Temporarily freezing the screen ...3 0 Temporarily blanking the screen ...3 0

Using the menu function .........3 1

Indication in OSD, Containing items of each menu

EASY MENU. . . . . . . . . . . . . . . 34

PICTURE menu ............ 36

IMAGE menu .............. 40

INPUT menu .............. 42

SETUP menu .............. 46

AUDIO menu .............. 52

SCREEN menu ............. 53

OPTION menu ............. 59

....3

.....1 0

.....1 5

1 6

. . 1 9

....2 4

. . 2 5



NETWORK menu ........... 72

SECURITY menu ........... 73

Presentation tools ......... 79

PC-LESS Presentation. .........7 9

Maintenance .............. 88

Replacing the lamp .............8 8

Cleaning and replacing the air lter . . 9 0 Replacing the internal clock battery

. .

.92

Other care ....................9 3

Troubleshooting ........... 94

Related messages .............9 4

Regarding the indicator lamps ....9 6

Resetting all settings ............9 8

Phenomena that may be easy to be mistaken for machine defects

...9 9

Specications ............ 104

Introduction

Features

The projector provides you with the broad use by the following features. ü This projector has a variety of I/O ports that supposedly cover for any

business scene. An HDMITM port can support various image equipment which have digital interface to get clearer pictures on a screen. This model has two HDMITM ports.

ü If you insert a USB storage device, such as a USB memory, into the US B

TY PE A port and select the port as the input source, you can view images

stored in the device.

ü This projector can be controlled and monitored via LAN connection.

Furthermore, you can use the designated USB wireless adapter (optional) to establish wireless LAN connection.

ü The built-in 16W speaker can deliver sufcient sound volume in a large space

like a classroom without external speakers.

ü Has an HDCR and an ACCENTUALIZER features which are original image

stabilizer for a clearer image.

ü Equipped with IMAGE OPTIMIZER which is original function to maintain

visibility by automatic image correction in accordance with lamp deterioration.

Checking the contents of package

Please see the C o n t e n t s o f p a c k a g e section in the Us e r ’ s M a n u a l ( c o n c i s e ) which is a book. Your projector should come with the items shown there. Require of your dealer immediately if any items are missing.

WARNING

not to put in the mouth. If swallowed, consult a physician immediately for emergency treatment.

NOTE

to use the original packing materials when moving the projector. Use special caution for the lens.

• The projector may make a rattling sound when tilted, moved or shaken, since a ap to control the air ow inside of the projector has moved. Be aware that this is not a failure or malfunction.

• Keep the original packing materials, for future reshipment. Be sure

►Keep small parts away from children and pets. Take care

Introduction

Part names

Projector

(1) Lamp cover (98)

The lamp unit is inside. (2) Speaker (22, 55) (3) Filter cover (100)

The air lter and intake vent are inside. (4) Elevator feet (x2) (25) (5) Elevator button (25) (6) Remote sensor (18) (7) Lens (103) (8) Lens cover (9) Intake vents (10) Control panel (5) (11) F O C US ring (25) (12) Z O O M ring (25) (13) A C (AC inlet) (15) (14) Exhaust vent (15) Ports (5)

(8)

(4)

(10)

(15)

(6)

(11)

(13)

(7)

(12)

(9)

(2)

(3)

(9)

(4)(5)

(5)

(1)

(14)

WARNING

►Do not open or remove any portion of the product, unless the manuals direct it. ►Do not subject the projector to unstable conditions. ►Do not apply a shock or pressure to this product. ►Do not look into the lens and the openings on the projector while the lamp is on, since the projection ray may cause a trouble on your eyes. ►Keep any object away from concentrated projection light beam. Blocking the beam by something causes high temperature and could result in re or smoke.

CAUTION

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Do not attach anything onto the lens because it could damage the lens, such as melting the lens. ►Do not attach anything onto the lens except the lens cover of this projector because it could damage the lens, such as melting the lens.

(continued on next page)

Part names (continued)

Control panel

(1) S TA ND B Y / O N button (

20) (2) INPUT button (23) (3) M E NU button (32) (4) L A M P indicator (106) (5) TE M P indicator (106) (6) PO W E R indicator (106)

Introduction

(4)(5)

(1) (3)(2) (6)

Ports(

10 ~ 14)

(1) L A N port (2) US B TY PE A port (x2) (3) US B TY PE B port (4) H D M I1 port (5) H D M I2 / M H L port (6) A UD IO IN1 port (7) A UD IO IN2 port (8) A UD IO IN3 (R , L ) ports (9) A UD IO O UT port (10) C O M PUTE R IN1 port

(1)

(11) C O M PUTE R IN2 / M O NITO R O UT port (12) C O NTR O L port (13) V ID E O port (14) Security slot (

16)

(15) Security bar (16)

(3)(2)

(4)

(5)

(10)

(11)

(9)

(14)

(continued on next page)

(12)

(8)

(13)

(6)

(7)

(15)

Introduction

Part names (continued)

Remote control

(1) INPUT button (23) (2) M Y B UTTO N- 1 button ( (3) M Y B UTTO N- 2 button ( (4) S TA ND B Y / O N button ( (5) A S PE C T button (

64, 65) 64, 65)

20)

24)

(6) Pb y P button * (7) A UTO button

(26)

(8) F R E E Z E button (31) (9) M A G NIF Y O N button (

30) (10) F O C US + button * (11) Z O O M + button * (12) V O L UM E + button ( (13) M A G NIF Y O F F

22)

button

(30) (14) F O C US - button * (15) Z O O M - button * (16) V O L UM E - button ( (17) PA G E UP button ( (18) G E O M E TR Y button (

22)

19)

27)

(19) PIC TUR E button (20) M UTE button ( (21) PA G E D O W N button (

22)

19)

(22) INTE R A C TIV E button * (23) NE TW O R K button (24) B L A NK button ( (25) E S C button ( (26) M E NU button ( (27) E NTE R button (

31)

19)

32)

(28) O S D M S G button (29) R E S E T button (

32) (30) ▲/▼/◄/►cursor buttons ( (31) Battery cover (

17)

32)

(2) (1) (6) (5)

(10)

(9)

(14) (13)

(17) (18) (21) (22) (25) (30) (28)

MYBUTTON

INPUT

1 2

AUTO

ASPECT

PbyP

MAGNIFY

FOCUS

ZOOM

OFF

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

NETWORK

ENTER

PAGE

ESC MENU

OSD MSG

FREEZE

VOLUME

BLANK

RESET

(3) (4) (7) (8) (11)

(12) (15)

(16) (20) (19) (24) (23) (26) (27) (29)

(31)

NOTE

Back of

the remote control

• Any button marked with “*” is not supported on this projector (105).

Setting up

Install the projector according to the environment and manner the projector will be used in.

For the case of installation in a special state such as ceiling mount, the specied mounting accessories ( service may be required. Before installing the projector, consult your dealer about your installation.

Specications in the Us e r ’ s M a n u a l ( c o n c i s e ) ) and

Arrangement

Refer to tables T- 1 to T- 3 and gures F - 1 and F - 2 at the end of User’s Manual (concise) to determine the screen size and projection distance. The values shown in the table are calculated for a full size screen.

a Screen size (diagonal) b Projection distance (±10%, from the projector’s end) c1 , c2 Screen height (±10%)

• If the projector is used at an altitude of about 1600 m (5250 feet) or higher, set ALTITUDE of the SERVICE item in the OPTION menu to HIGH ( Otherwise, set it to NORMAL. If the projector is used with a wrong setting, it may cause damage to the projector itself or the parts inside.

NOTE

suspended from the ceiling or other location due to the exibility of the plastic projector body. If readjustment is necessary, consult with your dealer or service personnel.

(continued on next page)

• The screen position may shift after installation if the projector is

69).

Setting up

Arrangement (continued)

WARNING

►In s t a l l t h e p r o j e c t o r w h e r e y o u c a n a c c e s s t h e p o w e r

o u t l e t e a s i l y . If an abnormality should occur, unplug the projector urgently.

Otherwise it could cause a re or electric shock. ►D o n o t s u b j e c t t h e p r o j e c t o r t o u n s t a b l e c o n d i t i o n s . If the projector falls or topples over, it could result in injury or damage to the projector and the surrounding things. Using a damaged projector could result in a re and an electric shock.

• Do not place the projector in unstable places, such as an inclined surface, places subject to vibration, on top of a wobbly table or cart, or a surface that is smaller than the projector.

• Do not put the projector on its side, front or rear position.

• Do not attach nor place anything on the projector unless otherwise specied in the manual.

• Do not use any mounting accessories except the accessories specied by the manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your dealer beforehand.

Do not install the projector near thermally conductive or ammable

► t h i n g s . Such things when heated by the projector could result in a re and burns.

• Do not place the projector on a metal stand.

►D o n o t p l a c e t h e p r o j e c t o r w h e r e a n y o i l s , s u c h a s c o o k i n g o r m a c h i n e o i l , a r e u s e d . Oil may harm the product, resulting in malfunction, or falling from the mounted position. Do not use adhesive such as threadlocker, lubricant and so on. ►D o n o t p l a c e t h e p r o j e c t o r i n a p l a c e w h e r e i t m a y g e t w e t . Getting the projector wet or inserting liquid into the projector could cause a re and an electric shock, and damage the projector.

• Do not place the projector near water, such as in a bathroom, kitchen, or poolside.

• Do not place the projector outdoors or by the window.

• Do not place anything containing liquid near the projector.

(continued on next page)

Arrangement (continued)

Setting up

CAUTION

►Place the projector in a cool place with sufcient v e n t i l a t i o n . The projector may shutdown automatically or may malfunction if its internal temperature is too high. Using a damaged projector could result in a re and an electric shock.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

• Do not place the projector where the air from an air conditioner or similar unit

will blow on it directly.

• Keep a space of 30 cm or more between a side of the projector and other

objects such as walls.

• Do not place the projector on carpet, cushions or bedding.

• Do not stop up, block nor cover the projector's vent holes. Do not place

anything around the projector that could be sucked in or stuck to the projector's intake vents.

• Do not place the projector at places that are exposed to magnetic elds, doing

so can cause the cooling fans inside the projector to malfunction. ►A v o i d p l a c i n g t h e p r o j e c t o r i n s m o k y , h u m i d o r d u s t y p l a c e . Placing the projector in such places could cause a re, an electric shock and malfunction of the projector.

• Do not place the projector near humidiers. Especially for an ultrasonic

humidier, chlorine and minerals contained in tap water are atomized and could

be deposited in the projector causing image degradation or other problems.

NOTICE

• Do not place the projector in a smoking area, kitchen, passageway

or by the window.

• Position the projector to prevent light from directly hitting the projector's remote sensor.

• Positional deviation or distortion of a projected image, or shift of the focus may occur due to ambient conditions, and so on. They tend to occur until the operation becomes stable, especially within about 30 minutes after the lamp is turned on. Check and readjust them as necessary.

• Do not place the product in a place where radio interference may be caused.

• Check and correct the setting for ALTITUDE of SERVICE in the OPTION menu according to the usage environment (

69). If the projector is used with a wrong

setting, it may cause damage to the projector itself or the parts inside.

• Keep heat-sensitive things away from the projector. Otherwise, they may be damaged by the heat from the projector.

Setting up

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to conrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. After making sure that the projector and the devices are turned off, perform the connection, according to the following instructions. Refer to the gures in subsequent pages. Before connecting the projector to a network system, be sure to read Ne t w o r k G u i d e too.

WARNING

cause a re or damage the projector and devices.

• Use only the accessories specied or recommended by the projector’s

manufacturer. It may be regulated under some standard.

• Neither disassemble nor modify the projector and the accessories.

• Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

CAUTION

w i t h t h e c o r e t o t h e p r o j e c t o r . That may be required by EMI regulations.

►Us e o n l y t h e a p p r o p r i a t e a c c e s s o r i e s . Otherwise it could

►F o r a c a b l e w i t h a c o r e a t o n l y o n e e n d , c o n n e c t t h e e n d

NOTE

• Do not turn on or off the projector while connected to a device in operation, unless that is directed in the manual of the device. Otherwise it may cause malfunction in the device or projector.

• The function of some input ports can be selected according to your usage requirements. Check the reference page indicated beside each port in the following illustration.

• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of

the projector are recessed.

About Plug-and-Play capability

• Plug-and-Play is a system composed of a computer, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the

C O M PUTE R IN 1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

- Please use the standard drivers in your computer as this projector is a Plug-

and-Play monitor.

(continued on next page)

1 0

Connecting with your devices (continued)

C o m p u t e r

Setting up

NOTE

• Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with a resolution up to UXGA

(1600x1200) or up to W-UXGA (1920x1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

• If you connect this projector and a notebook computer, you need output the display to an external monitor, or output simultaneously to the internal display and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (25).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display device. You may be able to see the dialog and set an appropriate display resolution.

(continued on next page)

1 1

Setting up

Connecting with your devices (continued)

US B

w i r e l e s s

a d a p t e r

(optional)

CAUTION

C o m p u t e r

A c c e s s

p o i n t

US B

s t o r a g e

d e v i c e

► Before connecting the projector to a network system be sure

E x t e r n a l d e v i c e

to obtain the consent of the administrator of the network. ►Do not connect the L A N port to any network that might have the excessive voltage. ►The designated USB wireless adapter that is sold as an option is required to use the wireless network function of this projector. ►Before removing the USB storage device from the port of the projector, be sure to use the REMOVE USB function on the thumbnail screen to secure your data (82). ►Do not use any extension cable or device when connecting the adapter to the projector. Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet. Do not touch the USB wireless adapter while the projector is receiving AC power. ►To connect both the LAN cable and USB device to the projector, use a LAN cable that is  at on the side where the plug’s wire is visible. Otherwise, both of them cannot be connected correctly, or the wire may break (malfunction).

NOTE

• If an oversized USB storage device blocks the L A N port, use a USB extension cable to connect the USB storage device.

(continued on next page)

1 2

Connecting with your devices (continued)

V C R / D V D / B l u - r a y D i s cTM p l a y e r

Setting up

NOTE

• The HDMITM port of this model is compatible with HDCP (Highbandwidth Digital Content Protection) and therefore capable of displaying a video signal from HDCP compatible DVD players or the like.

- The HDMITM port supports the following signals.

Video signal : 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60,

1080i@50/60, 1080p@50/60

Audio signal : Format Linear PCM

Sampling frequency 48kHz / 44.1kHz / 32kHz

- This projector can be connected with another equipment that has HDMITM

connector, but with some equipment the projector may not work properly, something like no video.

- Be sure to use an HDMITM cable that has the HDMITM logo.

- Use a Category 2-certi ed HDMITM cable to input 1080p@50/60 signal to the

projector.

- When the projector is connected with a device having DVI connector, use a

DVI to HDMITM cable to connect with the HDMITM input.

- The MHL supports the following signals. For Video signals, refer to User’s

Manual (detailed) Operating Guide –Technical. Audio signal : Format Linear PCM

Sampling frequency 48kHz / 44.1kHz / 32kHz

- Be sure to use an MHL® cable that has the MHL logo.

(continued on next page)

1 3

Setting up

Connecting with your devices (continued)

S p e a k e r s

(with an ampli er)

M o n i t o r

RGB IN

Note: The Dukane model described in this document is manufactured by Hitachi

and uses the same rmware, software programs, control code, and accessory parts. The equivalent Dukane to Hitachi models is 8945WU (CP-EU4501WN) , 8950WU (CP-EU5001WN) , and 8950W (CP-EW5001WN).

1 4

Connecting to a power supply

Put the connector of the power cord into the

A C (AC inlet) of the projector. Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the power supply connection, the PO W E R indicator will light up in steady orange.

Please remember that when the DIRECT POWER ON function activated (63), the connection of the power supply make the projector turn on.

Setting up

A C

Po w e r c o r d

WARNING

incorrect or faulty connections may result in re and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload the outlet and connectors, loosen the connection, or result in re, electric shock or other accidents.

• Connect the ground terminal for the AC inlet of this unit to the ground terminal of the building using an appropriate power cord (bundled).

NOTICE

phase voltage of 220 to 240 V.

►Please use extra caution when connecting the power cord, as

►This product is also designed for IT power systems with a phase-to-

Fastening the cable

Use the supplied cable tie to fasten the cable.

C a b l e t i e

1 5

Setting up

Fastening the adapter cover

Use the supplied adapter cover to prevent the USB wireless adapter from coming off easily.

Loosen the screw (marked with

triangle) on the bottom left of the

US B TY PE A port.

Insert the tab of the cover into the

hole at the upper right of the US B TY PE A port in the direction of the arrow.

Align the screw holes on the projector

and the cover. Then insert the screw removed from the projector into the hole and tighten the screw.

Tab

WARNING

to put in the mouth. Heat may build up in the USB wireless adapter, to avoid possible burns disconnect the projector power cord for more than 10 minutes before touching it.

Using the security bar and slot

A commercially available anti-theft chain or wire can be attached to the security bar on the projector. Refer to the  gure to choose an anti-theft chain or wire. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool.

WARNING

from falling down, since it is not designed for it.

CAUTION

It may become too hot.

NOTE

measures. It is intended to be used as supplemental theft prevention measure.

• The security bar and slot is not comprehensive theft prevention

►Keep small parts away from children and pets. Take care not

S e c u r i t y s l o t

1 2 . 2 m m

1 8 . 6 m m

1 8 . 0 m m

A n t i - t h e f t

c h a i n o r w i r e

►Do not use the security bar and slot to prevent the projector

►Do not place anti-theft chain or wire near the exhaust vents.

S e c u r i t y b a r

1 6

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Remove the battery cover.

Align and insert the two AA batteries

according to their plus and minus terminals as indicated in the remote control. (Use the appropriate AA carbon-zinc or alkaline batteries (non-rechargeable) in accordance with laws and regulations.)

Put the battery cover back to the former state.

WARNING

directed. Improper use may result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

• Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

• Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

►Always handle the batteries with care and use them only as

1 7

Remote control

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

(approx.)

NOTE

•

The remote control signal re ected in the screen or the like may be available.

If it is dif cult to send the signal to the sensor directly, attempt to make the signal re ect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter  uorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency. In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds.

(1) Set to Mode 1:NORMAL

V O L UM E - and R E S E T buttons

(2) Set to Mode 2:HIGH

M A G NIF Y O F F and E S C buttons

M A G NIF Y

O F F button

E S C

button

Please remember that the REMOTE FREQ. in the SERVICE item of the OPTION menu

(

68) of the projector to be

controlled should be set to the same mode as the remote control.

(2)

MYBUTTON

INPUT

1 2

ASPECT

PbyP

MAGNIFY

FOCUS

OFF

PAGE

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

ESC MENU

ENTER

OSD MSG

AUTO

FREEZE

(1)

VOLUME

ZOOM

V O L UM E -

NETWORK

button

BLANK

R E S E T

RESET

button

1 8

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse and keyboard of the computer, when the projector’s US B TY PE B port and the computer’s type A USB port are connected.

Remote control

(1) PA G E UP k e y : Press PA G E UP button. (2) PA G E D O W N k e y : Press PA G E D O W N button. (3) M o u s e l e f t b u t t o n : Press E NTE R button. (4) M o v e p o i n t e r : Use the cursor buttons ▲, ▼, ◄ and ►. (5) E S C k e y : Press E S C button. (6) M o u s e r i g h t b u t t o n : Press R E S E T button.

NOTICE

►Improper use of the simple mouse & keyboard function could damage your equipment. While using this function, please connect this product only to a computer. Be

US B TY PE B port

(1) (2)

(5)

(3)

MYBUTTON

INPUT

1 2

AUTO

ASPECT

PbyP

MAGNIFY

FOCUS

ZOOM

OFF

PAGE

GEOMETRY PICTURE MUTE

NETWORK

INTERACTIVE

DOWN

ESC MENU

ENTER

OSD MSG

FREEZE

VOLUME

BLANK

RESET

sure to check your computer’s manuals before connecting this product to the computer.

NOTE

When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

• When a USB cable connects this projector with a computer having a built-in pointing device (e.g. track ball) like a laptop computer, open BIOS setup menu, then select the external mouse and disable the built-in pointing device, because the built-in pointing device may have priority to this function.

Windows Vista® or higher is required for this function. And also this function may not work

• depending on the computer’s congurations and mouse drivers. This function can work with the computer which can operate general USB mouse or keyboard.

• You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

This function is activated only when the projector is working properly. This function is not

• available in any of the following cases:

- While the lamp is warming up. (The PO W E R indicator blinks in green.)

- When US B TY PE A port is selected.

- While displaying BLANK

, TEMPLATE

(57)

or MY IMAGE screen.

(53)

- When any menu is displayed on the screen. While using the cursor buttons to operate the sound or screen functions such as adjusting the

sound volume, correcting the keystone, correcting the picture position and magnifying the screen.

(4)

(6)

1 9

Power on/off

Turning on the power

Make sure that the power cord is

rmly and correctly connected to the

S TA ND B Y / O N button

PO W E R indicator

projector and the outlet.

Make sure that the PO W E R indicator is

lighted in steady orange (96). Then remove the lens cover.

Press the S TA ND B Y / O N button on the

projector or the remote control.

MYBUTTON

INPUT

1 2

ASPECT

PbyP

MAGNIFY

FOCUS

OFF

PAGE

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

ESC MENU

ENTER

OSD MSG

FREEZE

AUTO

VOLUME

ZOOM

NETWORK

BLANK

RESET

The projection lamp will light up and PO W E R indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green (96).

To display the picture, select an input signal according to the section S e l e c t i n g a n i n p u t s i g n a l (

23).

The INITIAL SETTING Menu will be displayed by factory default upon startup. Once the INITIAL SETTING Menu is set, it will not appear until FACTORY RESET (71) is executed. If you wish to change the settings, refer to the LANGUAGE (53) and ALTITUDE (67) menu.

(1) LANGUAGE: Use the ▲/▼/◄/►buttons to

select the desired language and press the

E NTE R button of the remote control or the INPUT button of the projector to execute.

(2) ALTITUDE: Use the ▲/▼ buttons to select

NORMAL for altitude below 1600 m (5250 feet), otherwise select HIGH and press the E NTE R button of the remote control or the INPUT button of the projector to execute.

(continued on next page)

2 0

Power on/off

Turning off the power

Press the S TA ND B Y / O N button on the projector or the remote control.

The message “Power off?” will appear on the screen for about 5 seconds.

Press the S TA ND B Y / O N button again while the message appears.

The projector lamp will go off, and the PO W E R indicator will begin blinking in orange. Then the PO W E R indicator will stop blinking and light in steady orange when the lamp cooling is completed (96).

Attach the lens cover, after the PO W E R indicator turns to steady orange.

Do not turn the projector on for about 10 minutes or more after turning it off. Also, do not turn the projector off shortly after turning it on. Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

WARNING

Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings since the projection ray may cause a trouble on your eyes. ►Keep any object away from concentrated projection light beam. Blocking the beam by something causes high temperature and could result in re or smoke. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE

prior to the connected devices.

• This projector has the function that can make the projector automatically turn

on/off. Please refer to the DIRECT POWER ON (60), AUTO POWER ON (60) and AUTO POWER OFF (60) items of the OPTION menu.

• Turn the power on/off in right order. Please power on the projector

►A strong light is emitted when the projector’s power is on.

2 1

Operating

FREEZE

VOLUME

Operating

Adjusting the volume

Use the V O L UM E + / - buttons to adjust the volume. A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds.

INPUT

ASPECT

PbyP

MAGNIFY

FOCUS

OFF

PAGE

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

ESC MENU

OSD MSG

VOLUME

MYBUTTON

1 2

AUTO

ZOOM

NETWORK

ENTER

FREEZE

VOLUME

BLANK

RESET

V O L UM E

buttons

+ / -

NOTE

When is selected for current picture input port, the volume

•

adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (52).

• Even if the projector is in the standby mode, the volume is adjustable when

both of the following conditions are true:

- An option other than is selected for AUDIO OUT in the STANDBY

OUTPUT item of the SETUP menu (51).

- NORMAL is selected in the STANDBY

MODE item of the SETUP menu

(49).

Temporarily muting the sound

Press M UTE button on the remote control. A dialog will appear on the screen indicating that you have muted the sound. To restore the sound, press the M UTE , V O L UM E + or V O L UM E - button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

NOTE

• When is selected for current picture input port, the sound is always muted. Please see AUDIO SOURCE item of AUDIO menu (52).

• C.C. (Closed Caption) is automatically activated when sound is muted and an input signal containing C.C. is received. This function is available only when the signal is NTSC for V ID E O or 480i@60 for C O M PUTE R IN1 or C O M PUTE R IN2 , and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (58).

INPUT

1 2

ASPECT

PbyP

MAGNIFY

FOCUS

OFF

PAGE

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

ESC MENU

OSD MSG

MYBUTTON

FREEZE

AUTO

VOLUME

ZOOM

MUTE

NETWORK

BLANK

ENTER

RESET

M UTE button

2 2

Operating

MYBUTTON

1 2

AUTO

FREEZE

INPUT

MYBUTTON

1 2

PbyP

Selecting an input signal

INPUT

Press INPUT button on the projector or the

remote control. Select a desirable input referring

button

to the displayed input list.

MYBUTTON

1 2

INPUT

FREEZE

AUTO

PbyP

ASPECT

INPUT

button

VOLUME

ZOOM

FOCUS

MAGNIFY

OFF

PAGE

GEOMETRY PICTURE MUTE

BLANK

NETWORK

INTERACTIVE

DOWN

ESC MENU

ENTER

RESET

OSD MSG

● While ON is selected for AUTO SEARCH item in OPTION menu (59), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

Selecting an aspect ratio

Press A S PE C T button on the remote control. Each time you press the button, the projector switches the mode for aspect ratio in turn.

NORMAL  4:3  16:9  16:10  14:9  ZOOM  NATIVE

NOTE

• A S PE C T button does not work when no proper signal is input.

• NORMAL mode keeps the original aspect ratio setting.

INPUT

1 2

ASPECT

PbyP

MAGNIFY

FOCUS

OFF

PAGE

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

ESC MENU

OSD MSG

ASPECT

MYBUTTON

AUTO

FREEZE

BLANK

RESET

A S PE C T button

VOLUME

ZOOM

NETWORK

ENTER

2 3

Operating

Adjusting the projector’s elevator

When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a

suitable angle to the screen, elevating the front side of the projector within 11 degrees.

This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable while pushing the elevator button on the same side as it.

Holding the projector, push the elevator buttons to loose the elevator feet.

Position the front side of the projector to the desired height.

Release the elevator buttons in order to lock the elevator feet.

After making sure that the elevator feet are locked, put the projector down

gently.

If necessary, the elevator feet can be manually twisted to make more precise

adjustments. Hold the projector when twisting the feet.

1 1

To loose an elevator foot, push the elevator button on the same side as it.

CAUTION ►Do not handle the elevator buttons without holding the projector, since the projector may drop down. ►Do not tilt the projector other than elevating its front within 11 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself.

Adjusting the zoom and focus

Use the Z O O M ring to adjust the screen size.

Use the F O C US ring to focus the picture.

2 4

To  nely adjust, twist the foot.

Z O O M ring F O C US ring

Using the automatic adjustment feature

FREEZE

Press A UTO button on the remote control. Pressing this button performs the following.

 F o r a c o m p u t e r s i g n a l

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted.

INPUT

ASPECT

MAGNIFY

OFF

PAGE UP

DOWN

ESC MENU

OSD MSG

Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

 F o r a v i d e o s i g n a l

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for

42).

the VIDEO FORMAT item in the INPUT menu (

The vertical position and

horizontal position will be automatically set to the default.

 F o r a c o m p o n e n t v i d e o s i g n a l

The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

MYBUTTON

1 2

PbyP

FOCUS

GEOMETRY PICTURE MUTE

INTERACTIVE

AUTO

FREEZE

VOLUME

ZOOM

NETWORK

BLANK

ENTER

RESET

A UTO button

Operating

NOTE

• The automatic adjustment operation requires approx. 10 seconds. Also

please note that it may not function correctly with some input.

• When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

• When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the computer model.

The items adjusted by this function may vary when the FINE or DISABLE is selected

• for the AUTO ADJUST item of the SERVICE item in the OPTION menu (

67).

2 5

Operating

AUTO

FREEZE

FOCUS

ZOOM

MYBUTTON

1 2

PbyP

VOLUME

PICTURE MUTE

Correcting the distortion

To correct the distortion of projected screen, you can select either KEYSTONE or PERFECT FIT. First press the G E O M E TR Y button to display the GEOMETRY CORRECTION menu, and point at one of the items with the ▲/▼ buttons.

MYBUTTON

INPUT

1 2

AUTO

FREEZE

ASPECT

PbyP

MAGNIFY

VOLUME

FOCUS

ZOOM

GEOMETRY

OFF

KEYSTONE: allows you to adjust the vertical and

horizontal keystone.

PERFECT FIT:

allows you to adjust each of the screen

PAGE

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

ESC MENU

OSD MSG

NETWORK

BLANK

ENTER

RESET

corners and sides to correct the distortion.

Use KEYSTONE / PERFECT FIT for adjustment. When one of them is selected, the other item is not available.

Then follow the procedure shown below for the item you selected.

G E O M E TR Y

button

NOTE

• The menu or dialog will automatically disappear after several seconds of inactivity. Press the G E O M E TR Y button again, or point the cursor at EXIT in the dialog and press the ►or E NTE R button to end the operation and close the menu or dialog.

K E Y S TO NE :



When KEYSTONE is pointed at, pressing the ► or E NTE R button displays the KEYSTONE dialog.

Select MANUAL with the ▲/▼ buttons and press

the ► or E NTE R button.

Select the vertical or horizontal keystone (

/ ) with the ▲/▼ buttons

and adjust the keystone distortion with the ◄/► buttons.

(continued on next page)

2 6

Correcting the distortion (continued)

Select AUTO with the ▲/▼ buttons and press the ► or E NTE R button.

Select EXECUTE with the ▲/▼ buttons and press the ► button for

2.1

automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.This function will be executed only once when selected in the menu. When the slant of the projector is changed, execute this function again.

Select ON/OFF with the ▲/▼ buttons and press the ► or E NTE R button.

2.2

ON: Automatic keystone distortion correction will be executed whenever

changing the slant of the projector.

This function is disabled. Please execute the AUTO

OFF:

automatic keystone distortion correction.

(27)

Operating

for

NOTE

• When REAR / CEILING or FRONT / CEILING is selected for the INSTALLATION item in the SETUP menu, the automatic vertical keystone correction function may not work correctly if the projector screen is slanted or tilted downwards.

• When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

• When the projector is placed on the level (about ±4°), the automatic keystone distortion correction may not work.

• When the projector is inclined to near ±30 degree or over, this function may not work well.

• This function will be unavailable when the TRANSITION DETECTOR is on (

76

• The display will be dark for a split second while switching the KEYSTONE, but this is not a malfunction.



When PERFECT FIT is pointed at, pressing the ► or E NTE R button displays the PERFECT FIT dialog.

This projector is equipped with a test pattern for PERFECT FIT. Select PATTERN with the buttons, then press the pattern.

• The adjustable range of this function will vary among inputs. For

some input,this function may not work well.

PE R F E C T F IT:

▲/▼

◄/►

buttons to select

(continued on next page)

2 7

Operating

Correcting the distortion (continued)

Select SETUP with the ▲/▼ buttons and press the ► or E NTE R button.

Select one of the corners or sides to be adjusted with the ▲/▼/◄/►

buttons and press the E NTE R or button.

Adjust the selected part as below.

● For adjusting a corner, use the ▲/▼/◄/► buttons to adjust the position of the corner.

● For adjusting the upper or lower side, use the ▲/▼ buttons to adjust the distortion of the side.

● For adjusting the left or right side, use the ◄/► buttons to adjust the distortion of the side.

● To adjust another corner or side, press the E NTE R or the procedure from step 2.

This projector is equipped with a memory feature for PERFECT FIT

adjustment. Up to 3 sets of adjustments can be stored.

● S A V E :

To store the current PERFECT FIT adjustment, select one of the "SAVE" options numbered 1 to 3 (number of the memory) with the ▲/▼ buttons and press the ►, E NTE R or Remember that the current data being stored of a memory will be lost by saving new data into the memory.

● L O A D :

To recall stored adjustments, select one of the "LOAD" options numbered 1 to 3 (number of the memory) with the ▲/▼ buttons and press the ►, E NTE R or Remember that the current adjusted condition will be lost by loading data. If you want to keep the current adjustment, please save it before performing a LOAD function.

button.

button and follow

NOTE

• There may be some noise and the screen may icker for a moment when loading data. This is not malfunction.

2 8

• The LOAD functions whose linked memory has no data are skipped.

Using the magnify feature

ASPECT

AUTO

FREEZE

FOCUS

ZOOM

INPUT

MYBUTTON

1 2

PbyP

VOLUME

MAGNIFY

Press the M A G NIF Y O N button on the remote

control. The picture will be magnied, and the MAGNIFY dialog will appear on the screen. When the

INPUT

ASPECT

MAGNIFY

OFF

PAGE

DOWN

ESC MENU

OSD MSG

M A G NIF Y O N button is pressed for the rst time after the projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to show each direction will be displayed.

The display magnication of the projector switches in order

with every press of the M A G NIF Y O N button.

1.5 times  2 times  3 times  4 times  1 time

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor

buttons to shift the magnifying area.

Press the M A G NIF Y O F F button on the remote control to exit magnication.

MYBUTTON

1 2

PbyP

FOCUS

GEOMETRY PICTURE MUTE

INTERACTIVE

ENTER

AUTO

FREEZE

ZOOM

VOLUME

NETWORK

BLANK

RESET

M A G NIF Y O N/ O F F

OFF

button

Operating

NOTE

• The MAGNIFY dialog will automatically disappear in several seconds with no operation. The dialog will appear again if the M A G NIF Y O N button is pressed when the dialog has automatically disappeared.

• The magnication is automatically disabled when the displaying signal or its display condition is changed.

• While the magnication is active, the keystone distortion condition may vary. It will be restored when the magnication is disabled.

• Some horizontal stripes might be visible on the image while magnication is active.

• This function is not available in the following cases:

- A sync signal in the range not supported is input.

- There is no input signal.

2 9

Operating

FREEZE

VOLUME

Temporarily freezing the screen

Press the F R E E Z E button on the remote control. The “FREEZE” indication will appear on the screen (however, the indication will not appear when SILENT is selected for the OSD MESSAGE item in the SETUP (51)), and the projector will go into the

INPUT

ASPECT

PbyP

MAGNIFY

FOCUS

OFF

PAGE

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

ESC MENU

OSD MSG

MYBUTTON

1 2

AUTO

ZOOM

NETWORK

ENTER

FREEZE

VOLUME

BLANK

RESET

F R E E Z E

button

FREEZE mode, which the picture is frozen. To exit the FREEZE mode and restore the screen to normal, press the F R E E Z E button again.

NOTE

• The projector automatically exits from the FREEZE mode when some control buttons are pressed.

• If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

• Images might appear degraded when this function is operated, but it is not a malfunction.

Temporarily blanking the screen

Press B L A NK button on the remote control. The BLANK screen will be displayed instead of the screen of input signal. Please refer to BLANK item in SCREEN menu (53). To exit from the BLANK screen and return to the input signal screen, press B L A NK button again.

INPUT

ASPECT

PbyP

FOCUS

MAGNIFY

OFF

PAGE

GEOMETRY PICTURE MUTE

INTERACTIVE

DOWN

ESC MENU

OSD MSG

MYBUTTON

1 2

AUTO

FREEZE

ZOOM

VOLUME

NETWORK

ENTER

BLANK

RESET

B L A NK

button

• The projector automatically exits from the BLANK mode when some control

buttons are pressed.

CAUTION

►If you wish to have a blank screen while the projector's lamp is on, use the BLANK function above. Taking any other action may cause the damage on the projector.

NOTE

• The sound is not connected with the BLANK screen function. If

necessary, set the volume or mute rst.

3 0

+ 74 hidden pages