Dukane 8934 User Manual

Projector

8934

User's Manual (detailed) Network Guide

Thank you for purchasing this product.

This manual is intended to explain only the network function. For proper use of this product, please refer to this manual and the other manuals for this product.

WARNING

►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

Features

This projector has the network function that brings you the following main features.

ü Web Control : allows you to monitor and control the projector through a network from a

computer. (

ü Network Bridge : allows you to control an external device through the projector from a

computer. (

NOTE

• The illustrations in this manual are for illustrative purposes. They may differ

slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

Trademark acknowledgment

•

Microsoft®, Internet Explorer®, Windows®, Windows Vista®, Windows 7®, Windows 8® and

Aero

• Adobe® and Flash® are registered trademarks of Adobe Systems Incorporated.

• Pentium

• JavaScript

• HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

• Crestron

trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and other countries.

• Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.

All other trademarks are the properties of their respective owners.

&9)

&40)

• The information in this manual is subject to change without notice.

are registered trademarks of Microsoft Corporation in the U.S. and/or other countries.

is a registered trademark of Intel Corporation.

is a registered trademark of Sun Microsystems, Inc.

, Crestron e-Control®, e-Control®, Crestron RoomView® and RoomViewTM are

430-8934-Net-00

Contents

1. Connection to the network ...................................................... 4

1.1 System requirements ................................................................................. 4

1.1.1 Required equipment preparation ..................................................................................... 4

1.1.2 Hardware and software requirement for computer .......................................................... 4

1.2 Manual network connection setting - Wired LAN -. ..................................... 5

1.2.1 Equipments connection .................................................................................................... 5

1.2.2 Network settings .............................................................................................................. 5

1.2.3 “Internet Option” setting ................................................................................................... 8

2. Web Control .............................................................................. 9

2.1 Projector Web Control ............................................................................... 10

2.1.1 Logon ............................................................................................................................. 10

2.1.2 Network Information ....................................................................................................... 11

2.1.3 Network Settings ............................................................................................................ 12

2.1.4 Port Settings .................................................................................................................. 14

2.1.5 Mail Settings .................................................................................................................. 16

2.1.6 Alert Settings .................................................................................................................. 17

2.1.7 Schedule Settings .......................................................................................................... 19

2.1.8 Date/Time Settings ......................................................................................................... 21

2.1.9 Security Settings ............................................................................................................ 23

2.1.10 Projector Control .......................................................................................................... 24

2.1.11 Remote Control ............................................................................................................ 29

2.1.12 Projector Status ........................................................................................................... 30

2.1.13 Network Restart ........................................................................................................... 31

2.2 Crestron e-Control® .................................................................................. 32

2.2.1 Main window .................................................................................................................... 33

2.2.2 Tools window ................................................................................................................... 35

2.2.3 Info window ..................................................................................................................... 37

2.2.4 Help Desk window ........................................................................................................... 38

2.2.5 Emergency Alert .............................................................................................................. 39

3. Network Bridge Function ....................................................... 40

3.1 Connecting devices .................................................................................. 40

3.2 Communication setup ............................................................................... 41

3.3 Communication port ................................................................................. 41

3.4 Transmission method ............................................................................... 42

3.4.1 HALF-DUPLEX .............................................................................................................. 42

3.4.2 FULL-DUPLEX ............................................................................................................... 43

Contents

4. Other Functions ...................................................................... 44

4.1 E-mail Alerts ............................................................................................. 44

4.2 Event Scheduling ..................................................................................... 46

4.3 Command Control via the Network .......................................................... 49

4.4 Crestron RoomView

................................................................................. 54

5. Troubleshooting ..................................................................... 55

6. Warranty and after-sales service .......................................... 56

1. Connection to the network

1.1 System requirements

1.1.1 Required equipment preparation

The following equipments are required to connect the projector to your computer through the network.

■ Common The projector: 1 unit, Computer : minimum 1 set

■ Depending on how you want to connect

LAN cable (CAT-5 or greater): 1 piece *1

*1: The system for using the network function of the projector requires

communication environment conforming 100Base-TX or 10Base-T.

1.1.2 Hardware and software requirement for computer

To connect your computer to the projector and use the network function of the projector, your computer needs to meet the following requirements.

ü OS: One of the following.

Windows Windows Vista® Home Basic /Home Premium /Business /Ultimate /Enterprise (Service Pack 1 or later) Windows® 7 Starter /Home Basic /Home Premium /Professional /Ultimate / Enterprise Windows ® 8 Windows ® 8 Pro/Enterprise

ü CPU: Pentium 4 (2.8 GHz or higher) ü Graphic card: 16 bit, XGA or higher ü Memory: 512 MB or higher ü Hard disk space: 100 MB or higher ü Web browser: Internet Explorer

XP Home Edition /Professional Edition

6.0 or higher

NOTE

• The network communication control is disabled while the projector is in standby mode if the STANDBY MODE item is set to SAVING. Please connect the network communication to the projector after setting the STANDBY MODE to NORMAL. (&SETUP menu in the Operating Guide)

1. Connection to the network

1.2 Manual network connection setting - Wired LAN -

This section explains how to set it up manually.

1.2.1 Equipments connection

Connect the projector and a computer with a LAN cable. * Before connecting with an existing network, contact the network administrator.

Next, check the following computer settings.

1.2.2 Network settings

This is an explanation of network connection settings for Windows

1) Log on to Windows

7 as administrator authority. Administrator authority is the

account, which can access to all functions.

2) Open “Control Panel” from “Start” menu.

3) Open “View network status and tasks” in “Network and Internet”. With the icons in the "Control Panel" window displayed, click "Network and

Sharing Center".

4) Click "Change adapter settings" in the menu

on the left side of the "Network and Sharing

Center" window.

(continued on next page)

1. Connection to the network

1.2 Manual network connection setting - Wired LAN - (continued)

5) Right-click "Local Area Connection" to open the menu, and select "Properties".

6) Select "Internet Protocol Version 4 (TCP/IPv4)" and click [Properties].

7) Select "Use the following IP address" and congure the IP address, Subnet mask and Default gateway for the computer accordingly. If a DHCP server exists in the network, you can select "Obtain an IP address automatically" and the IP

address will be assigned automatically. After setting is complete, click [OK] to close the window.

(continued on next page)

1. Connection to the network

1.2 Manual network connection setting - Wired LAN - (continued)

[About IP address]

■ Setting manually

The Network address portion of the IP address setting on your computer must be the same as the setting on the projector. Also, the entire IP address on the computer must not overlap with that of the other devices on the same network,

including the projector.

For example

The projector’s settings are as follows.

IP address: 192.168.1.254

Subnet mask: 255.255.255.0

(Network address: 192.168.1 in this case)

Therefore, specify the computer’s IP address as follows.

IP address: 192.168.1.xxx (xxx shows decimal number.)

Subnet mask: 255.255.255.0

(Network address: 192.168.1 in this case)

Select from 1 to 254 for “xxx” not duplicating with any other equipments.

In this case, since the IP address of the projector is “192.168.1.254”, specify a

setting between 1 to 253 for the computer.

NOTE

• “0.0.0.0” cannot be set to the IP address.

• The projector’s IP address can be changed by using the conguration utility via a web browser. (&12)

• If the projector and the computer exist in the same network (i.e., same network address), you can leave the default gateway eld blank.

• When the projector and the computer exist in different networks, the default

gateway must be set. Consult to the network administrator in detail.

■ Setting automatically

When a DHCP server exists in the connected network, it is possible to assign an IP address to the projector and computer automatically.

* DHCP is abbreviation for “Dynamic Host Conguration Protocol” and has

the function to provide necessary setting for network like IP address from

server to client. A server that has DHCP function is called DHCP server.

(continued on next page)

1. Connection to the network

1.2 Manual network connection setting - Wired LAN - (continued)

1.2.3 “Internet Option” setting

1) Click “Internet Options” in “Network and

Sharing Center” window to open “Internet

Properties” window.

2) Click “Connections” tab and then click [LAN settings] button to open “Local Area Network (LAN) Settings”.

3) Uncheck all boxes in “Local Area Network (LAN) Settings”

window. After setting is complete, click [OK] to close the window.

2. Web Control

You can adjust or control the projector via a network from a web browser on a

computer that is connected to the same network.

NOTE

• Internet Explorer® 6.0 or later is required.

• If JavaScript® is disabled in your web browser conguration, you must enable JavaScript® in order to use the projector web pages properly. See the Help les for your web browser for details on how to enable JavaScript®.

• It is recommended that all web browser updates are installed.

Refer to the following for conguring or controlling the projector via a web browser. Make sure that your computer and the projector is connected via network, and

then start Web browser.

Enter the projector's IP address into URL input box of the Web browser as the

example below, and then press the Enter key or button. Example: If the IP address of the projector is set to 192.168.1.10:

Enter “http://192.168.1.10/” into the address bar of the web browser and press the Enter key or click

button.

If a correct URL is input, and the

projector and your computer are connected to the same network correctly, the selection window as shown on the right will be displayed.

You can choose to use Projector Web Control or Crestron e-Control® as a tool

for controlling the projector. Click one of them. For more details, refer to 2.1 Projector

Web Control (&10) or 2.2 Crestron e-Control® (&32).

NOTE

• If Crestron e-Control in the Network Settings (&12) is set to Disable, the selection window above does not appear, but the Logon window of the Projector Web Control is displayed.

• Crestron e-Control® is created using Flash®. You need to install Adobe® Flash® Player on your computer to use Crestron e-Control®.

2. Web Control

2.1 Projector Web Control

2.1.1 Logon

To use the Projector Web Control function, you need

to logon with your user name and password.

Below are the factory default settings for user

name and password.

User name Administrator

Logon window

Password <blank>

Enter your user name and password, and then click the [OK]. If you logon successfully, the screen below will be displayed.

Main menu

Click the desired operation or conguration item on the main menu.

NOTE

• The language used on the Projector Web Control screen is the same as that of the OSD on the projector. If you want to change it, you need to change the OSD language on the projector. (&SCREEN menu in the

Operating Guide)

2.1 Projector Web Control (continued)

2.1.2 Network Information

Displays the projector’s current network conguration settings.

Item Description

Projector Name Displays the projector name settings.

DHCP Displays the DHCP setting.

IP Address Displays the IP address. Subnet Mask Displays the subnet mask.

Default Gateway Displays the default gateway. DNS Server Address Displays the DNS server address.

MAC Address Displays the MAC address.

2. Web Control

2.1 Projector Web Control (continued)

2.1.3 Network Settings

Displays and congures network settings.

Item Description

Congures the name of the projector. The length of the Projector Name can be up to 64 alphanumeric

Projector Name

IP Conguration Congures network settings.

DHCP ON Enables DHCP. DHCP OFF Disables DHCP.

IP Address Congures the IP address when DHCP is disabled. Subnet Mask Congures the subnet mask when DHCP is disabled.

Default Gateway Congures the default gateway when DHCP is disabled.

DNS Server Address Congures the DNS server address.

AMX D.D. (AMX Device Discovery)

Crestron e-Control

characters. Only alphabets, numbers and following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space. Particular projector name is pre-assigned by default.

Congures the AMX Device Discovery setting to detect the projector from the controllers of AMX connected to the same network. For the details of AMX Device Discovery, visit the AMX

web site.

URL: http://www.amx.com

Set whether to or not to use Crestron e-Control If you choose Disable, the Logon window of Projector Web Control will be displayed at rst, but the selection window will

not appear.

Click the [Apply] button to save the settings.

2.1 Projector Web Control (continued)

2. Web Control

NOTE

• The new conguration settings are activated after restarting the network connection. When the conguration settings are changed, you must restart the network connection. You can restart the network connection by

clicking [Network Restart] on the main menu (&31).

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

2. Web Control

2.1 Projector Web Control (continued)

2.1.4 Port Settings

Displays and congures communication port

settings.

Item Description

Network Control Port1

(Port:23)

Port open Click the [Enable] check box to use port 23.

Authentication

Network Control Port2

(Port:9715)

Port open Click the [Enable] check box to use port 9715.

Authentication

PJLink

Port

(Port:4352)

Port open Click the [Enable] check box to use port 4352.

Authentication

Congures command control port 1 (Port:23).

Click the [Enable] check box when authentication is required for this port.

Congures command control port 2 (Port:9715).

Click the [Enable] check box when authentication is required for this port.

Congures the PJLink

port (Port:4352).

Click the [Enable] check box when authentication is required for this port.

(continued on next page)

2.1 Projector Web Control - Port Settings (continued)

Item Description

Network Bridge Port Congures the Bridge port number.

Input the port number.

Port number

Except for 41794, 9715, 9716, 9719, 9720, 5900, 5500, 4352 between 1024 and 65535 can be set up. It is set to 9717 as the default setting.

Click the [Apply] button to save the settings.

2. Web Control

NOTE

clicking the [Network Restart] on the main menu(&31).

2. Web Control

2.1 Projector Web Control (continued)

2.1.5 Mail Settings

Displays and congures e-mail addressing

settings.

Item Description

Send Mail

SMTP Server Address

Sender E-mail address

Recipient E-mail address

Click the [Enable] check box to use the e-mail function. Congure the conditions for sending e-mail under the Alert

Settings.

Congures the address of the mail server in IP format.

• The address allows not only IP address but also domain name if the valid DNS server is setup in the Network

Settings. The maximum length of host or domain name is up to 255 characters.

Congures the sender e-mail address. The length of the sender e-mail address can be up to 255

alphanumeric characters.

Congures the e-mail address of up to ve recipients. You

can also specify the [to] or [cc] for each address. The

length of the recipient e-mail address can be up to 255

alphanumeric characters.

Click the [Apply] button to save the settings.

NOTE

• You can conrm whether the mail settings work correctly using the

[Send Test Mail] button. Please enable Send mail setting before clicking the [Send Test Mail].

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

2.1 Projector Web Control (continued)

2.1.6 Alert Settings

Displays and congures failure & alert settings.

Item Description

Cover Error The lamp cover has not been properly xed.

Fan Error The cooling fan is not operating.

Lamp Error

Temp Error

Air Flow Error The internal temperature is rising.

Cold Error

Filter Error Filter time over.

Other Error

Schedule Execution Error

Lamp Time Alarm Lamp time over Alarm Time setting. Filter Time Alarm Filter time over Alarm Time setting.

The lamp does not light, and there is a possibility that interior portion has become heated.

There is a possibility that the interior portion has become heated.

There is a possibility that the interior portion has become

overcooled.

Other error. If displaying this error, please contact your dealer.

Schedule Execution error. (

&19

)

2. Web Control

Refer to &Troubleshooting in the Operating Guide for further detailed explanation of Error except Other Error and Schedule Execution Error.

+ 39 hidden pages