Dukane 8925H-RJ, 8926H-RJ, 8927HW-RJ User Manual

LCD Data Video Projector

General User’s Manual

MODELS 8925H-RJ,

8926H-RJ, 8927HW-RJ, 8956H-RJ

Information in this Guide may change due to product improvements. To obtain the latest manuals, literature, and software please visit the Dukane web site at; www.dukane.com/av

and look at the specic model SUPPORT or DOWNLOADS section.

DUKANE CORP AV SERVICE DEPT

2900 Dukane Drive St Charles, IL 60174 800-676-2487 / 630-762-4032 Fax 630-584-5156 avservice@dukane.com www.dukane.com/av

403-8925H-RJ-PLUS-GENERAL-00

Projector

+5-+5-/ +:5-+5-

User's Manual (detailed) Operating Guide

Thank you for purchasing this projector.

WARNING

product. Be sure to read Safety Guide rst. After reading them, store them in a safe place for future reference.

►Before using this product, please read all manuals for this

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING

CAUTION

NOTICE This entry notices of fear of causing trouble.

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

• Mac® is a registered trademark of Apple Inc.

• Windows in the U.S. and/or other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

•

HDMI, the HDMI logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

• Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.

• Blu-ray Disc

All other trademarks are the properties of their respective owners.

• The information in this manual is subject to change without notice.

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



, DirectDraw® and Direct3D® are registered trademarks of Microsoft Corporation

is a trademark.

Contents



Introduction . . . . . . . . . . . . . . . 3

Features . . . . . . . . . . . . . . . . . . . . . . 3

Checking the contents of package

Part names . . . . . . . . . . . . . . . . . . . . 4

Setting up . . . . . . . . . . . . . . . . . 7

Arrangement ...................7

Connecting with your devices Connecting to a power supply

.....10

.....15

Fastening the adapter cover ......

Using the security bar and slot . . . . 16

Remote control ............17

Installing the batteries ...........17

About the remote control signal . . . 17 Changing the frequency of remote control signal Using as a simple PC mouse & keyboard

. . 18

Power on/off . . . . . . . . . . . . . . 19

Turning on the power . . . . . . . . . . . 19

Turning off the power . . . . . . . . . . . 19

Operating . . . . . . . . . . . . . . . . 20

Adjusting the volume ............20

Temporarily muting the sound .....20

Selecting an input signal .........21

Searching an input signal . . . . . . . . 22

Selecting an aspect ratio .........22

Adjusting the projector's elevator . . 23

Adjusting the zoom and focus .....23

Using the automatic adjustment feature

...24

Adjusting the position . . . . . . . . . . . 24

Correcting the keystone distortions

Using the magnify feature ........26

Temporarily freezing the screen . . . 27 Temporarily blanking the screen . . 27

Using the menu function . . . . . . . . 28

EASY MENU. . . . . . . . . . . . . . . 30

As p e c t , Au t o k e y s t o n e , k pi c t u r e m o d e , F

i l t e r t i m e , lA n g u A g e , A d v A n c e d m e n u , ex i t

ec o m o d e , mi r r o r , re s e t ,

e y s t o n e

PICTURE menu . . . . . . . . . . . . 32

Br i g h t n e s s , co n t r A s t , gA m m A , co l o r t e m p , co l o r , ti n t , sh A r p n e s s , A c t i v e i ri s , my m e m o r y

IMAGE menu . . . . . . . . . . . . . . 35

As p e c t , ov e r s c A n , v p o s i t i o n , h p o s i t i o n , h

p h A s e , h s i z e , Au t o A d j u s t e x e c u t e

INPUT menu . . . . . . . . . . . . . . 38

pr o g r e s s i v e , vi d e o n r , co l o r s p A c e , c

o m p o n e n t , vi d e o F o r m A t , hd m i F o r m A t ,

d m i r A n g e , co m p u t e r i n , Fr A m e l o c k ,

e s o l u t i o n

SETUP menu ..............42

...3

AUDIO menu . . . . . . . . . . . . . . 45

SCREEN menu .............47

OPTION menu . . . . . . . . . . . . . 53

. . 18

NETWORK menu ...........63

SECURITY menu ...........74

Presentation tools . . . . . . . . . 80

. . 25

Maintenance ..............94

Troubleshooting . . . . . . . . . . . 99

Specications ............108



Au t o k e y s t o n e , e

c o m o d e ,

o n i t o r o u t

vo l u m e , sp e A k e r , Au d i o s o u r c e , h

d m i A u d i o , mi c l e v e l , mi c v o l u m e

lA n g u A g e , me n u p o s i t i o n , Bl A n k , s

t A r t u p ,

e s s A g e , so u r c e n A m e , te m p l A t e , c.c.

Au t o s e A r c h , Au t o k e y s t o n e , d

i r e c t p o w e r o n , Au t o p o w e r o F F ,

s B t y p e B, lA m p t i m e , Fi l t e r t i m e ,

y B u t t o n , my s o u r c e , se r v i c e

wi r e l e s s s e t u p , wi r e l e s s i n F o r m A t i o n , w

i r e d s e t u p , wi r e d i n F o r m A t i o n ,

r o j e c t o r n A m e , my i m A g e ,

m x d.d., pr e s e n t A t i o n , se r v i c e

se c u r i t y p A s s w o r d c h A n g e ,

y s c r e e n p A s s w o r d , pi n l o c k ,

r A n s i t i o n d e t e c t o r , my t e x t p A s s w o r d ,

y t e x t d i s p l A y , my t e x t w r i t i n g

PC-LESS Presentation

Thumbnail Mode, Full Screen Mode, Slideshow mode, Playlist

USB Display

Starting USB Display, Right-Click menu, Floating menu, Options window

e y s t o n e , A u t o e c o m o d e ,

mi r r o r , st A n d B y m o d e ,

yScreen

, M

yScreen Lock

. . . . . . . 80

..................

Replacing the lamp .............94

Cleaning and replacing the air lter . . 96

Other care ....................98

Related messages . . . . . . . . . . . . . 99

Regarding the indicator lamps . . . 101

Resetting all settings ...........103

Phenomena that may be easy

to be mistaken for machine defects

. 103

Introduction

Features

The projector provides you with the broad use by the following features. ü This projector has a variety of I/O ports that supposedly cover for any

business scene. The HDMI port can support various image equipment which have digital interface to get clearer pictures on a screen.

ü If you insert a USB storage device, such as a USB memory, into the USB

TYPE A port and select the port as the input source, you can view images

stored in the device.

ü This projector can be controlled and monitored via LAN connection.

Furthermore, you can use the designated USB wireless adapter (optional) to establish wireless LAN connection.

ü The built-in 16W speaker can deliver sufcient sound volume in a large space

like a classroom without external speakers.

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise) which is a book. Your projector should come with the items shown there. Require of your dealer immediately if any items are missing.

WARNING

not to put in the mouth. If swallowed, consult a physician immediately for emergency treatment.

NOTE

to use the original packing materials when moving the projector. Use special caution for the lens.

• The projector may make a rattling sound when tilted, moved or shaken, since a ap to control the air ow inside of the projector has moved. Be aware that this is not a failure or malfunction.

• Keep the original packing materials, for future reshipment. Be sure

►Keep small parts away from children and pets. Take care

Introduction

Part names

Projector

(11)

(12)

(1) Lamp cover (94)

The lamp unit is inside. (2) Speaker (20, 45) (3) Filter cover (96)

(9)

The air lter and intake vent are inside. (4) Elevator feet (x2) (23) (5) Elevator buttons (x2) (23) (6) Remote sensor (17) (7) Lens (98) (8) Lens cover

(4)

(10)

(8)

(7)

(3)

(6)

(5)

(4)

(1)

(9) Intake vents (10) Control panel (5) (11) FOCUS ring (23) (12) ZOOM ring (23) (13) AC IN (AC inlet) (15) (14) Exhaust vent (15) Rear panel (5)

WARNING

►Do not open or remove any portion of the product, unless the

(15)

(14)

(13)

manuals direct it. ►Do not subject the projector to unstable conditions. ►Do not apply a shock or pressure to this product. ►Do not look into the lens and the openings on the projector while the lamp is on.

CAUTION

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Do not attach anything onto the lens except the lens cover of this projector because it could damage the lens, such as melting the lens.

(2)

(5)

(continued on next page)

Part names (continued)

Control panel

(1) STANDBY/ON button (

19) (2) INPUT button (21) (3) MENU button (28) (4) LAMP indicator (101) (5) TEMP indicator (101) (6) POWER indicator (101)

Introduction

(4)(5)

(1) (3)(2) (6)

Rear panel (

10 ~ 14)

(1) LAN port (2) USB TYPE A port (3) HDMI port (4) USB TYPE B port (5) MIC port (

14) (6) AUDIO IN1 port (7) AUDIO IN2 port (8) AUDIO IN3 (R,L) ports (9) AUDIO OUT (R,L) ports (10) COMPUTER IN1 port

(1)

(6)

(5)

(11) COMPUTER IN2 port (12) MONITOR OUT port (13) CONTROL port (14) COMPONENT ports (Y, Cb/Pb, Cr/Pr) (15) VIDEO port (16) S-VIDEO port (17) Security slot (16) (18) Security bar (16)

(11)(10)(4)(3)(2)

(17)

(continued on next page)

(8)

(16)(7) (9) (14) (13) (12)

(15)(18)

Introduction

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

Part names (continued)

Remote control

(1) VIDEO button (

21) (2) COMPUTER button (21) (3) SEARCH button (22) (4) STANDBY/ON button (19) (5) ASPECT button (22) (6) AUTO button (24) (7) BLANK button (27) (8) MAGNIFY - ON button (26) (9) MAGNIFY - OFF button (26) (10) MY SOURCE/DOC.CAMERA button

(21, 57) (11) VOLUME - button (20) (12) PAGE UP button (18) (13) PAGE DOWN button (18) (14) VOLUME + button (20) (15) MUTE button (20) (16) FREEZE button (27) (17) MY BUTTON - 1 button (56, 57) (18) MY BUTTON - 2 button (56, 57) (19) KEYSTONE button (26) (20) POSITION button (24, 29) (21) MENU button (28) (22) ▲/▼/◄/► cursor buttons (28) (23) ENTER button (28) (24) ESC button (28) (25) RESET button (29) (26) Battery cover (17)

(2) (1) (6) (5) (16) (8) (9) (19) (17) (20) (22)

(24)

the remote control

(10) (4) (3) (7) (12) (14) (11) (13) (15) (18) (21) (23) (25)

Back of

(26)

Setting up

Install the projector according to the environment and manner the projector will be used in.

For the case of installation in a special state such as ceiling mount, the speci ed mounting accessories (

Speci cations in the User’s Manual (concise)) and service may be required. Before installing the projector, consult your dealer about your installation.

Arrangement

Refer to tables T-1 and T-2 at the back of User's Manual (concise) as well as the following to determine the screen size and projection distance. The values shown in the table are calculated for a full size screen.

Ⓗ×Ⓥ :

Screen size

ⓐ :

Projection distance (from the projector's end)

ⓑ,ⓒ

: Screen height

(continued on next page)

Projector top

Projector bottom

Setting up

Arrangement (continued)

WARNING

►Install the projector where you can access the power

outlet easily. If an abnormality should occur, unplug the projector urgently.

Otherwise it could cause a re or electric shock. ►Do not subject the projector to unstable conditions. If the projector falls or topples over, it could result in injury or damage to the projector and the surrounding things. Using a damaged projector could result in a re and an electric shock.

• Do not place the projector in unstable places, such as an inclined surface, places subject to vibration, on top of a wobbly table or cart, or a surface that is smaller than the projector.

• Do not put the projector on its side, front or rear position.

• Do not attach nor place anything on the projector unless otherwise specied in the manual.

• Do not use any mounting accessories except the accessories specied by the manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your dealer beforehand.

►

Do not install the projector near thermally conductive or ammable

things. Such things when heated by the projector could result in a re and burns.

• Do not place the projector on a metal stand.

►Do not place the projector where any oils, such as cooking or machine oil, are used. Oil may harm the product, resulting in malfunction, or falling from the mounted position. ►Do not place the projector in a place where it may get wet. Getting the projector wet or inserting liquid into the projector could cause a re and an electric shock, and damage the projector.

• Do not place the projector near water, such as in a bathroom, kitchen, or poolside.

• Do not place the projector outdoors or by the window.

• Do not place anything containing liquid near the projector.

(continued on next page)

Arrangement (continued)

Setting up

CAUTION

►Place the projector in a cool place with sufcient ventilation. The projector may shutdown automatically or may malfunction if its internal temperature is too high. Using a damaged projector could result in a re and an electric shock.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

• Do not place the projector where the air from an air conditioner or similar unit

will blow on it directly.

• Keep a space of 30 cm or more between a side of the projector and other

objects such as walls.

• Do not place the projector on carpet, cushions or bedding.

• Do not stop up, block nor cover the projector's vent holes. Do not place

anything around the projector that could be sucked in or stuck to the projector's intake vents.

• Do not place the projector at places that are exposed to magnetic elds, doing

so can cause the cooling fans inside the projector to malfunction. ►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause a re, an electric shock and malfunction of the projector.

• Do not place the projector near humidiers. Especially for an ultrasonic

humidier, chlorine and minerals contained in tap water are atomized and could

be deposited in the projector causing image degradation or other problems.

• Do not place the projector in a smoking area, kitchen, passageway or by the

window.

NOTICE

• Position the projector to prevent light from directly hitting the

projector's remote sensor.

• Do not place the product in a place where radio interference may be caused.

• Check and correct the setting for FAN SPEED of SERVICE in the OPTION menu according to the usage environment (

57). If the projector is used with a

wrong setting, it may cause damage to the projector itself or the parts inside.

• Keep heat-sensitive things away from the projector. Otherwise, they may be damaged by the heat from the projector.

Setting up

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to conrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. After making sure that the projector and the devices are turned off, perform the connection, according to the following instructions. Refer to the gures in subsequent pages. Before connecting the projector to a network system, be sure to read Network Guide too.

WARNING

►Use only the appropriate accessories. Otherwise it could

cause a re or damage the projector and devices.

• Use only the accessories specied or recommended by the projector’s

manufacturer. It may be regulated under some standard.

• Neither disassemble nor modify the projector and the accessories.

• Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

CAUTION

►For a cable with a core at only one end, connect the end

with the core to the projector. That may be required by EMI regulations.

NOTE

• Do not turn on or off the projector while connected to a device in operation, unless that is directed in the manual of the device. Otherwise it may cause malfunction in the device or projector.

• The function of some input ports can be selected according to your usage requirements. Check the reference page indicated beside each port in the following illustration.

• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of

the projector are recessed.

About Plug-and-Play capability

• Plug-and-Play is a system composed of a computer, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the

COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

- Please use the standard drivers in your computer as this projector is a Plug-

and-Play monitor.

(continued on next page)

Connecting with your devices (continued)

Computer

(39)

(54)

(45)

Setting up

(40) (40)

NOTE

• Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600x1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

• If you connect this projector and a notebook computer, you need output the display to an external monitor, or output simultaneously to the internal display and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (40).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display device. You may be able to see the dialog and set an appropriate display resolution.

(continued on next page)

Setting up

Connecting with your devices (continued)

Access point

USB wireless adapter

(optional)

(63)

USB storage device

(80)

CAUTION

Computer

(54)

(63)

► Before connecting the projector to a network system be sure

External device

(59)

to obtain the consent of the administrator of the network. ►Do not connect the LAN port to any network that might have the excessive voltage. ►The designated USB wireless adapter that is sold as an option is required to use the wireless network function of this projector. ►Before removing the USB storage device from the port of the projector, be sure to use the REMOVE USB function on the thumbnail screen to secure your data (83). ►Do not use any extension cable or device when connecting the adapter to the projector. Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet. Do not touch the USB wireless adapter while the projector is receiving AC power. ►To connect both the LAN cable and USB device to the projector, use a LAN cable that is at on the side where the plug’s wire is visible. Otherwise, both of them cannot be connected correctly, or the wire may break (malfunction).

NOTE

• If an oversized USB storage device blocks the LAN port, use a USB extension cable to connect the USB storage device.

(continued on next page)

Connecting with your devices (continued)

VCR/DVD/Blu-ray Disc

player

Setting up

NOTE

(39)

(45)

• The HDMI port of this model is compatible with HDCP (High-band-

(40) (40)

(39)

(38)

width Digital Content Protection) and therefore capable of displaying a video signal from HDCP compatible DVD players or the like.

- The HDMI supports the following signals.

Video signal : 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60,

1080i@50/60, 1080p@50/60

Audio signal : Format Linear PCM

Sampling frequency 48kHz / 44.1kHz / 32kHz

- This projector can be connected with another equipment that has HDMITM

connector, but with some equipment the projector may not work properly, something like no video.

- Be sure to use an HDMITM cable that has the HDMITM logo.

- Use a Category 2-certied HDMITM cable to input 1080p@50/60 signal to the

projector.

- When the projector is connected with a device having DVI connector, use a

DVI to HDMITM cable to connect with the HDMI input.

(continued on next page)

Setting up

Connecting with your devices (continued)

Speakers

(with an amplier)

Microphone

system

(45)

(46)

NOTE

• If a loud feedback noise is produced from the speaker, move the microphone away from the speaker.

Monitor

(44)

Microphone function

•

You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug. In that case, the built-in speaker outputs the sound from the microphone, even while the sound from the projector is output. You can input line level signal to the MIC port from equipment such as wireless microphone. Select HIGH in the MIC LEVEL item of the AUDIO menu when you input line level audio signal to the MIC port. In the normal mode, the volume of the microphone can be adjusted separately from the volume of the projector using the menu (46). In the standby mode, the volume of the microphone is adjustable with the VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector (20). Even when the sound of projector is set to mute mode by the AUDIO SOURCE function (45), the volume of the microphone is adjustable. In both modes (standby or normal), the MUTE button on the remote control works on the sounds of the microphone and the projector (20).

• This projector doesn't support plug-in power for the microphone.

Connecting to a power supply

Put the connector of the power cord into the

AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

Please remember that when the DIRECT POWER ON function activated (53), the connection of the power supply make the projector turn on.

Setting up

AC IN

Power cord

WARNING

incorrect or faulty connections may result in re and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload the outlet and connectors, loosen the connection, or result in re, electric shock or other accidents.

• Connect the ground terminal for the AC inlet of this unit to the ground terminal of the building using an appropriate power cord (bundled).

NOTICE

phase voltage of 220 to 240 V.

►Please use extra caution when connecting the power cord, as

►This product is also designed for IT power systems with a phase-to-

Setting up

Fastening the adapter cover

Use the supplied adapter cover to prevent the USB wireless adapter from coming off easily.

Loosen the screw (marked with

triangle) on the bottom left of the

USB TYPE A port.

Insert the tab of the cover into the

hole at the upper right of the USB TYPE A port in the direction of the arrow.

Align the screw holes on the

projector and the cover. Then insert the screw removed from the projector into the hole and tighten the screw.

WARNING

to put in the mouth.

►Keep small parts away from children and pets. Take care not

Using the security bar and slot

A commercially available anti-theft chain or wire can be attached to the security bar on the projector. Refer to the gure to choose an anti-theft chain or wire. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool.

Tab

Security slot

11.7mm

17.5mm

20.3mm

Anti-theft

chain or wire

WARNING

from falling down, since it is not designed for it.

CAUTION

It may become too hot.

NOTE

measures. It is intended to be used as supplemental theft prevention measure.

• The security bar and slot is not comprehensive theft prevention

►Do not use the security bar and slot to prevent the projector

►Do not place anti-theft chain or wire near the exhaust vents.

security bar

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery

cover, remove it. Align and insert the two AA batteries

(HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control. Replace the battery cover in the direction of the arrow and snap it back into place.

21 3

WARNING

directed. Improper use may result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

•

If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

►Always handle the batteries with care and use them only as

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

•

NOTE

If it is difcult to send the signal to the sensor directly, attempt to make the signal reect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter uorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

The remote control signal reected in the screen or the like may be available.

(approx.)

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

Remote control

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency. In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds.

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons

(2)

(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons Please remember that the REMOTE FREQ. in the SERVICE item of

the OPTION menu

(58)

of the projector to be controlled should be

set to the same mode as the remote control.

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse and keyboard of the computer, when the projector’s USB TYPE B port and the computer’s type A USB port are connected and MOUSE is selected for the USB TYPE B item in the OPTION menu (

(1) PAGE UP key: Press PAGE UP button. (2) PAGE DOWN key: Press PAGE DOWN button. (3) Mouse left button: Press ENTER button. (4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►. (5) ESC key: Press ESC button. (6) Mouse right button: Press RESET button.

54).

USB TYPE B port

(1)

(2)

NOTICE

►Improper use of the simple mouse & keyboard function could damage your equipment. While using this function, please connect this product only to a computer. Be sure to check your computer’s manuals before connecting this product to the computer.

NOTE

When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

• When a USB cable connects this projector with a computer having a built-in pointing device (e.g. track ball) like a laptop PC, open BIOS setup menu, then select the external mouse and disable the built-in pointing device, because the built-in pointing device may have priority to this function.

Windows 95 OSR 2.1 or higher is required for this function. And also this function may not work

• depending on the computer’s congurations and mouse drivers. This function can work with the computer which can operate general USB mouse or keyboard.

• You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

This function is activated only when the projector is working properly. This function is not

• available in any of the following cases:

- While the lamp is warming up. (The POWER indicator blinks in green.)

- When either USB TYPE A or USB TYPE B port is selected.

- While displaying BLANK

- When any menu is displayed on the screen. While using the cursor buttons to operate the sound or screen functions such as adjusting the

- sound volume, correcting the keystone, correcting the picture position and magnifying the screen.

(47)

, TEMPLATE

(51)

or MY IMAGE

(3)

(5)

(71)

(4)

(6)

screen.

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

Power on/off

Turning on the power

Make sure that the power cord is rmly and

correctly connected to the projector and the

STANDBY/ON button

POWER indicator

outlet. Make sure that the POWER indicator is

steady orange (101). Then remove the lens cover.

Press STANDBY/ON button on the

projector or the remote control. The projection lamp will light up and POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green (101).

To display the picture, select an input signal according to the section Selecting an input signal (21).

Turning off the power

Press the STANDBY/ON button on the projector or the remote control.

The message “Power off?” will appear on the screen for about 5 seconds. Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (101).

Attach the lens cover, after the POWER indicator turns in steady orange.

Do not turn the projector on for about 10 minutes or more after turning it off. Also, do not turn the projector off shortly after turning it on. Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

WARNING

►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE

• Turn the power on/off in right order. Please power on the projector

prior to the connected devices.

•

This projector has the function that can make the projector automatically turn on/ off. Please refer to the DIRECT POWER ON items of the OPTION menu.

(53)

and AUTO POWER OFF

(54)

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





Operating

Adjusting the volume

Use the VOLUME +/VOLUME - buttons to adjust the volume.

A dialog will appear on the screen to aid you in adjusting the

VOLUME +/- button

volume. If you do not do anything, the dialog will automatically disappear after a few seconds.

● When

is selected for current picture input port, the volume adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (45).

● Even if the projector is in the standby mode, the volume is adjustable when both of the following conditions are true:

- An option other than is selected for STANDBY in the AUDIO SOURCE item of the AUDIO menu (45).

NORMAL is selected in the STANDBY MODE item of the SETUP menu

● In the standby mode, the volume of the microphone is adjustable with the VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector.

Temporarily muting the sound

Press MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted

MUTE button

the sound. To restore the sound, press the MUTE, VOLUME + or VOLUME - button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

(44).

● When is selected for current picture input port, the sound is always muted. Please see AUDIO SOURCE item of AUDIO menu (45).

● C.C. (Closed Caption) is automatically activated when sound is muted and an input signal containing C.C. is received. This function is available only when the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPONENT, COMPUTER IN1 or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (52).

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





Selecting an input signal

Press INPUT button on the projector.

Each time you press the button, the projector switches its

INPUT button

input port from the current port as below.

COMPUTER IN1  COMPUTER IN2  LAN

VIDEO USB TYPE A

S-VIDEO USB TYPE B

COMPONENT (Y, Cb/Pb, Cr/Pr)  HDMI

● While ON is selected for AUTO SEARCH item in OPTION menu (53), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

● It may take several seconds to project the images from the USB TYPE B port.

Press COMPUTER button on the remote control.

Each time you press the button, the projector switches its

COMPUTER button

input port from the current port as below.

COMPUTER IN1  COMPUTER IN2  LAN USB TYPE B  USB TYPE A

●

While ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (53). If COMPUTER button is pressed when VIDEO, S-VIDEO, COMPONENT or HDMI port is selected, the projector will check COMPUTER IN1 port rst.

●

It may take several seconds to project the images from the USB TYPE B port.

Press VIDEO button on the remote control.

Each time you press the button, the projector switches its

VIDEO button

input port from the current port as below. HDMI  COMPONENT  S-VIDEO  VIDEO

● While ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (

53). If VIDEO button is pressed when COMPUTER IN1,

COMPUTER IN2, LAN, USB TYPE A or USB TYPE B port is selected, the

projector will check HDMI port rst.

Press the MY SOURCE / DOC. CAMERA button on

the remote control. The input signal will be changed

MY SOURCE / DOC. CAMERA button

into the signal you set as MY SOURCE (57).

● This function also can use for document camera. Select the input port that connected the document camera.

Operating

Searching an input signal

Press SEARCH button on the remote control.

The projector will start to check its input ports as below in order to nd any input signals. When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER IN1  COMPUTER IN2  LAN

SEARCH button

VIDEO

COMPUTER

DOC.CAMERA

ASPECT

AUTO

FREEZE

MAGNIFY

OFF

MY BUTTON

KEYSTONE



POSITION

VIDEO USB TYPE A

S-VIDEO USB TYPE B

COMPONENT  HDMI

ESC

● While ON is selected for AUTO SEARCH item in OPTION menu (53), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

●

It may take several seconds to project the images from the USB TYPE B port.

Selecting an aspect ratio

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

 For a computer signal

8925H-RJ, 8926H-RJ, 8956H-RJ: NORMAL  4:3  16:9  16:10

CP-8927HW-RJ: NORMAL  4:3  16:9  16:10  NATIVE

 For an HDMITM signal

8925H-RJ, 8926H-RJ, 8956H-RJ: NORMAL  4:3  16:9  16:10  14:9

CP-8927HW-RJ: NORMAL  4:3  16:9  16:10  14:9  NATIVE

 For a video signal, s-video signal or component video signal

8925H-RJ, 8926H-RJ, 8956H-RJ: 4:3  16:9  14:9

CP-8927HW-RJ: 4:3  16:9  16:10  14:9  NATIVE

 For an input signal from the LAN, USB TYPE A or USB TYPE B port, or

if there is no signal

8925H-RJ, 8926H-RJ, 8956H-RJ: 4:3 (xed) 8927H-RJ: 16:10 (xed)

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

ASPECT button

VIDEO

ASPECT

MAGNIFY

OFF

KEYSTONE

POSITION

COMPUTER

DOC.CAMERA

AUTO

FREEZE

MY BUTTON



ESC

MY SOURCE/

PAGE

DOWN

MY SOURCE/

PAGE

DOWN

BLANK

VOLUME

㧗

࡯

MUTE



RESET

BLANK

VOLUME

㧗

࡯

MUTE



RESET

Adjusting the projector’s elevator

14°

When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 14 degrees. This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable while pushing the elevator button on the same side as it.

Holding the projector, push the elevator buttons to

loose the elevator feet. Position the front side of the projector to the desired

height. Release the elevator buttons in order to lock the

elevator feet. After making sure that the elevator feet are locked,

put the projector down gently. If necessary, the elevator feet can be manually

twisted to make more precise adjustments. Hold the projector when twisting the feet.

Operating

To loose an elevator foot, push the elevator button on the same side as it.

To nely adjust, twist the foot.

CAUTION

projector, since the projector may drop down. ►Do not tilt the projector other than elevating its front within 14 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself.

Adjusting the zoom and focus

Use the ZOOM ring to adjust the screen size.

Use the FOCUS ring to focus the picture.

►Do not handle the elevator buttons without holding the

ZOOM ring FOCUS ring

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





Using the automatic adjustment feature

Press AUTO button on the remote control.

Pressing this button performs the following.

 For a computer signal

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

 For a video signal and s-video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for

39).

the VIDEO FORMAT item in the INPUT menu (

The vertical position and

horizontal position will be automatically set to the default.

 For a component video signal

The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

● The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

● When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

● When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model. The items adjusted by this function may vary when the FINE or DISABLE is selected

● for the AUTO ADJUST item of the SERVICE item in the OPTION menu (

AUTO button

57).

Adjusting the position

Press POSITION button on the remote control when no menu is

indicated. The “POSITION” indication will appear on the screen.

Use the ▲/▼/◄/► cursor buttons to adjust the picture position.

When you want to reset the operation, press RESET button on the remote control during the operation. To complete this operation, press POSITION button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

When this function is performed on a video signal or an s-video signal, some image

● such as an extra-line may appear at outside of the picture.

● When this function is performed on a video signal or s-video signal, the range of this adjustment depends on OVER SCAN in IMAGE menu ( possible to adjust when OVER SCAN is set to 10.

● If POSITION button is pressed when a menu is indicated on screen, the displayed picture does not move its position but the menu does.

● This function is unavailable for a signal from the LAN, USB TYPE A, USB TYPE B or HDMI port.

POSITION button

35) setting. It is not

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





Correcting the keystone distortions

Press KEYSTONE button on the remote

control. A dialog will appear on the screen

KEYSTONE button

to aid you in correcting the distortion.

Use the ▲/▼ cursor buttons to select AUTO or MANUAL

operation, and press the ► button to perform the following. (1) AUTO executes automatic vertical keystone correction.

(2) MANUAL displays a dialog for keystone correction.

Use the ◄/► buttons for adjustment.

To close the dialog and complete this operation, press KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● The menu or dialog will automatically disappear after several seconds of inactivity. Pressing the KEYSTONE button again nishes the operation and closes the menu or dialog.

● The adjustable range of this function will vary among inputs. For some input, this function may not work well.

● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, automatic vertical keystone correction may not work correctly.

● When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

● When the projector is placed on the level (about ±4°), the automatic keystone distortion correction may not work.

● When the projector is inclined to near ±30 degree or over, this function may not work well.

● This function will be unavailable when the Transition Detector is on (

77).

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





Using the magnify feature

Press the MAGNIFY ON button on the remote control.

The picture will be magnied, and the MAGNIFY dialog

MAGNIFY ON/OFF button

will appear on the screen. When the MAGNIFY ON button is pressed for the rst time after the

projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to show each direction will be displayed.

The display magnication of the projector switches in order with every press

of the MAGNIFY ON button.

 For computer signals, HDMI

(RGB) signals, input signals from the

LAN, USB TYPE A or USB TYPE B port

1.5 times  2 times  3 times  4 times  1 time

 For video signals, s-video signals, component video signals or

HDMI

(Component) signals

1.5 times  2 times  1 time

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor

buttons to shift the magnifying area.

Press the MAGNIFY OFF button on the remote control to exit magnication.

● The MAGNIFY dialog will automatically disappear in several seconds with no operation. The dialog will appear again if the MAGNIFY ON button is pressed when the dialog has automatically disappeared.

● The magnication is automatically disabled when the displaying signal or its display condition is changed.

● While the magnication is active, the keystone distortion condition may vary. It will be restored when the magnication is disabled.

● Some horizontal stripes might be visible on the image while magnication is active.

● This function is not available in the following cases:

- A sync signal in the range not supported is input.

- There is no input signal.

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





Operating

Temporarily freezing the screen

Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however,

FREEZE button

the indication will not appear when the OFF is selected for the MESSAGE item in the SCREEN menu (49)), and the projector will go into the FREEZE mode, which the picture is frozen. To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.

● The projector automatically exits from the FREEZE mode when some control buttons are pressed.

● If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

● Images might appear degraded when this function is operated, but it is not a malfunction.

Temporarily blanking the screen

Press BLANK button on the remote control.

The BLANK screen will be displayed instead of the screen of input signal. Please refer to BLANK item in SCREEN menu (47). To exit from the BLANK screen and return to the input signal screen, press BLANK button again.

BLANK button

● The projector automatically exits from the

BLANK

some control buttons are pressed.

CAUTION

►If you wish to have a blank screen while the projector's lamp is on, use the BLANK function above. Taking any other action may cause the damage on the projector.

•

NOTE

The sound is not connected with the BLANK screen function. If necessary, set the volume or mute rst. To display the BLANK screen and mute the sound at one time, use AV MUTE function

(57).

mode when

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

POSITION

ESC

RESET

ENTER

Operating

Using the menu function

This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, SECURITY and EASY MENU. EASY MENU consists of functions often used, and the other menus are classied into each purpose and brought together as the ADVANCED MENU. Each of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. The basic operations of these menus are as follows.

POSITION button

To start the MENU, press the MENU button. The MENU you last used (EASY

or ADVANCED) will appear. EASY MENU has priority to appear just after powered on.

In the EASY MENU

(1) Use the ▲/▼ cursor buttons to select an item to

operate. If you want to change it to the ADVANCED MENU, select the ADVANCED MENU.

(2) Use the ◄/► cursor buttons to operate the item.

In the ADVANCED MENU

(1) Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU, select the EASY MENU. The items in the menu appear on the right side.

(2) Press the ► cursor button or ENTER button to

move the cursor to the right side. Then use the ▲/▼ cursor buttons to select an item to operate and press the ► cursor button or ENTER button to progress. The operation menu or dialog of the selected item will appear.

(3) Use the buttons as instructed in the OSD to operate the item.

(continued on next page)

ENTER button

ESC button

MENU button

(Cursor buttons)

Cursor buttons

RESET button

+ 80 hidden pages