Dukane 8120WIA, 8121WIA User Manual

Projector

8120WIA/8121WIA

User's Manual (detailed) Operating Guide

Thank you for purchasing this projector.

WARNING

product. Be sure to read “Safety Guide” rst. After reading them, store them in a safe place for future reference.

►Before using this product, please read all manuals for this

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING

CAUTION

NOTICE This entry notices of fear of causing trouble.

NOTE

• The illustrations in this manual are for illustrative purposes. They may differ slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

• The information in this manual is subject to change without notice.

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



430-8120WIA-8121WIA-General-00

Contents



Introduction ...............3

Features ...................... 3

Checking the contents of package

Part names ....................4

Setting up .................9

Arrangement ...................9

Connecting with your devices Connecting to a power supply

Using the security bar and slot ....18

Using the cable cover ...........19

Remote control ............20

Interactive pen ............23

Power on/off ..............24

Operating ................27

Adjusting the volume ............27

Temporarily muting the screen and

audio output ..................27

Selecting an input signal .........28

Selecting an aspect ratio .........28

Selecting an Interactive Function . . 29

Calibration ....................29

Adjusting the projector's elevator . . 30

Adjusting the zoom and focus .....30

Using the automatic adjustment feature

Using the TEMPLATE feature .....32

Other buttons .................32

Adjusting the position ........... 33

Correcting the keystone/perfect t distortions

....................33

Using the magnify feature ........34

Temporarily freezing the screen ...35

Using the menu function ........36

EASY MENU. . . . . . . . . . . . . . . 38

Iwb calIbrate, aspect,

Keystone,

Keystone, perfect fIt

eco moDe, InstallatIon, reset, fIlter tIme, l

anguage, aDvanceD menu, exIt

D-zoom,

, pIcture moDe,

IWB menu ................41

PICTURE menu ............42

brIghtness, contrast, hDcr, a

ccentualIzer, gamma, color temp,

color, tInt, sharpness, actIve IrIs, my memory

IMAGE menu ..............46

aspect, over scan, v posItIon, h posItIon, h phase, h sIze, auto aDjust execute

...3

.....12

.....18

...31



INPUT menu ..............49

progressIve, vIDeo nr, color space, vIDeo format, DIgItal format, DIgItal

range, computer In, frame locK,

esolutIon, mhl stanDby pwr.

SETUP menu ..............54

D-zoom, D-shIft, pIct.posIt.h,

Keystone, perfect fIt

amp & fIlter, Image optImIzer, InstallatIon

l stanDby moDe

Keystone,

, setup memory,

AUDIO menu ..............61

volume, speaKer, auDIo source, mIc level,mIc volume

SCREEN menu .............63

language, menu posItIon, blanK, auto blanK, start up,

yScreen Lock

template, c.c.

, message, source name,

yScreen

OPTION menu .............69

auto search, DIrect power on, auto power off, my button, scheDule, s

ervIce

NETWORK menu ...........83

SECURITY menu ...........84

securIty passworD change,

my text passworD, my text DIsplay, my text wrItIng, clonIng locK

passworD, pIn locK,

yScreen

Presentation tools .........89

Interactive function ...............89

PC-LESS Presentation USB Display (Windows® computer) USB Display (Mac computer)

..........116

. 126

......131

Maintenance .............135

Replacing the lamp ............135

Cleaning and replacing the air lter . 137

Caring for the projection window and camera lens

Replacing the internal clock battery

...................139

...

140

Other care ...................141

Troubleshooting ..........142

Related messages ............142

Regarding the indicator lamps ...144

Resetting all settings ...........147

Phenomena that may be easy to

be mistaken for machine defects

. . 147

Specications ............159

Introduction

Features

The projector provides you with the broad use by the following features.

ü The unique optics system produces a large projected image in a short

distance, which provides you with various ways of use.

ü This projector has a variety of I/O ports that supposedly cover for any

business scene.

ü The HDMI/MHL port can support various image equipment which have digital

interface to get clearer pictures on a screen.

ü Has HDCR and ACCENTUALIZER features which are Dukane's original

image stabilizer for a clearer image.

ü Has DICOM

mode.This mode simulates the DICOM standard, which is a standard applicable to digital communications in medicine.

ü This projector can be controlled and monitored via LAN connection.

Furthermore, you can use the designated USB wireless adapter (optional) to establish wireless LAN connection.

ü The built-in 16W speaker can deliver sufcient sound volume in a large

space like a classroom without external speakers.

ü This projector's network supports the PJLink™ standard.PJLink™ is a unied

standard for operating and controlling data projectors.For specications of PJLink™, see the web site of the PJLink™.

ü Equipped with IMAGE OPTIMIZER which is Dukane's original function to

maintain visibility by automatic image correction in accordance with lamp deterioration.

ü The Interactive Pen included with the projector allows you to write or draw

directly on the projected image. Also, you can control the connected computer on the screen in the same way as using a mouse.

("Digital Imaging and Communication in Medicine") simulation

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise) which is a book. Your projector should come with the items shown there. Require of your dealer immediately if any items are missing.

NOTE

to use the original packing materials when moving the projector. Use special caution for the lens.

• Keep the original packing materials, for future reshipment. Be sure

Introduction

Part names

Projector

(1) Lamp cover (135)

The lamp unit is inside. (2) Control panel (5) (3) Elevator feet (x 2) (30) (4) Remote sensor (x 2)(21) (5) Projection window (139) (6) Intake vents (7) Filter cover (137)

The air lter and intake vent

are inside. (8) Speaker (15, 27, 61) (9) Exhaust vent (10) AC (AC inlet) (18) (11) Ports (6) (12) Security bar (18) (13) Security slot (18) (14) Spacer (x 2) (30) (15) Battery cover (140) (16) Camera lens (139)

(8)

(14)

(4)

(7)

(1)

(6)

(3)

HOT!

(9)

HOT!

(2)

(3)

(5)

(11)

(13)

(12)

(15)

(14)

(16)

(10)

WARNING

►HOT! : Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Never look into the projection window while the projection lamp lights, since the projection lamp ray may cause a trouble on your eyes. ►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

CAUTION

►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air lter periodically.

Introduction

Part names (continued)

Control panel

(1) STANDBY/ON button (

24)

(3)

(4)

(6)

(2) INPUT button (28) (3) POWER indicator (24, 144) (4) TEMP indicator (144) (5) LAMP indicator (144) Buttons ◄/►/▲/▼ (6) FOCUS +/- buttons

when no menu is displayed (31), or

(5)

(7)

(2)

(1)

Cursor ◄/► buttons

when a menu is displayed (36). FOCUS +/- function is invalid when the USB TYPE A port is selected as the input source.

(7) MENU buttons

when no menu is displayed (36), or

Cursor ▲/▼ buttons

when a menu is displayed (36). The ◄/►/▲/▼ buttons on the projector work only as the cursor buttons while the template is displayed (67).

Note: The Dukane models described in this document are manufactured by

Hitachi and use the same rmware, software programs, control code, and accessory parts. The equivalent Dukane to Hitachi models are; 8120WIA (CP-TW2505), and 8121WIA (CP-TW3005).

Introduction

Part names (continued) Ports (

12 ~ 17)

(1) USB TYPE A port (x2) (2) LAN port (3) USB TYPE B port (4) HDMI1/MHL port (5) HDMI2 port (6) MIC port

(9) AUDIO OUT port (10) COMPUTER IN1 port (11) COMPUTER IN2 / MONITOR OUT port (12) VIDEO IN port (13) CONTROL port (14) Option port *

(7) AUDIO IN1 port (8) AUDIO IN2(L,R) ports

(11)

(9)

(10)

(7)

NOTE

(12)

(6)

(5)

(4)

(3)

(13)

* Option port is a port used only when using the optional part (FT-01B).

(8)

(14)

(2)

(1)

A cover is attached for protecting the port. Do not remove the cover. Refer to the manual of the optional part (FT-01B) for detail.

Part names (continued)

Remote control

Introduction

(1) INPUT button (

28) (2) IWB button (29) (3) CALIBRATION button (29) (4) STANDBY/ON button (24) (5) ASPECT button (28) (6) AUTO button (31) (7) ACCENTUALIZER button (32) (8) HDCR button (32) (9) FOCUS - button (31) (10) FOCUS + button (31) (11) D-ZOOM - button (30) (12) D-ZOOM + button (30) (13) PAGE UP button (22) (14) MAGNIFY - ON button (34) (15) MY BUTTON - 1 button (71) (16) VOLUME + button (27) (17) PAGE DOWN button (22) (18) MAGNIFY - OFF button (34) (19) MY BUTTON - 2 button (71) (20) VOLUME - button (27) (21) KEYSTONE/PERFECT FIT button (33) (22) TEMPLATE button (32) (23) FREEZE button (35) (24) AV MUTE button (27) (25) ESC button (36) (26) MENU button (36, 37) (27) ENTER button (36, 37) (28) POSITION button (33, 37) (29) RESET button (36) (30) ▲/▼/◄/► cursor buttons (36) (31) Battery cover (20)

(2) (1) (6) (5)

INPUT

ASPECT

(10) (9) (13) (14) (17) (18)

PAGE

KEYSTONE/

PERFECT FIT

ESC MENU

(21) (22) (25) (30)

POSITION

(28)

the remote control

IWB

CALIBRATION

AUTO

ACCENTUALIZER

D-ZOOM

FOCUS

MAGNIFY

MYBUTTON

DOWNONOFF

FREEZE

TEMPLATE

ENTER

Back of

HDCR

VOLUME

AV MUTE

RESET

(3) (4) (7) (8) (11)

(12)

＋

(16)

ー

(15) (20) (19) (24) (23) (26) (27) (29)

(31)

Introduction

Part names (continued)

Interactive pen

(1) Pen tip (

23)

(2) Battery cover (23)

NOTE

• Interactive Pen is henceforth denoted as "pen".

(1) (2)

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to table T-1 and gures F-1 and F-2 at the end of User’s Manual (concise) to determine the screen size and projection distance.

The values shown in the table are calculated for a full size screen.

Screen size (diagonal)

• For the case of installation in special conditions such as on the wall or ceiling, the specied mounting accessories and service may be required. Tabletop use must be setup with the designated optional accessories. Before installing the projector, consult your dealer about your installation.

The screen position may shift after installation if the projector is mounted on locations

• such as the wall or ceiling, due to the exibility of the plastic projector body. If readjustment is necessary, consult with your dealer or service personnel.

• The projected image position and/or focus may change during warm-up (approx. 30 minutes after the lamp is turned on) or when the ambient conditions change. Readjust the image position and/or focus as necessary.

• Since the projector features an ultra short throw, be aware that it is required to select a screen carefully to have better performance.

- A soft screen such as a pull-down screen may cause serious distortion of a projected image. A hard screen such as a board screen is recommended for use with this projector.

- A high-gain screen such as a bead screen that has narrow viewing angle is not suitable for this projector. A low-gain screen (around 1.0) such as a matte screen that has wide viewing angle is recommended for use with this projector.

A screen with a weave pattern may cause moiré on the projected image, which is not a failure of the projector. A screen that has less moiré effects is recommended for use with this projector.

b1 , b2

Projection distance (±8%)

c1 , c2 Screen height (±8%)

►

WARNING

Place the projector in a stable horizontal position. If the projector falls or is knocked over, it could cause injury and/or damage to the projector. Using a damaged projector could then result in re and/or electric shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side or front position. To place the projector

on its rear position for the table top use, it is required to use the designated optional parts. Consult with your dealer.

• Consult with your dealer before a special installation such as on the wall or

ceiling.

(continued on next page)

Setting up

Arrangement (continued)

WARNING

►Place the projector in a cool place, and ensure that there is sufcient ventilation. The high temperature of the projector could cause re, burns and/or malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

• Do not place or attach anything that would block the projection window, camera

lens or vent holes.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

Do not place the projector where the air from an air conditioner or similar unit will blow on it directly.

•

Do not place anything near the projection window or vents, or on top of the

projector. It causes high temperature and could result in re or smoke.

•

Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the bottom. ►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector.

•

Do not place the projector where any oils, such as cooking or machine oil, are used.

►

Use only the mounting accessories the manufacturer specied, and leave installing

and removing the projector with the mounting accessories to the service personnel.

• Read and keep the user’s manual of the mounting accessories used.

(continued on next page)

Arrangement (continued)

Setting up

CAUTION

►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector near humidiers, smoking spaces or a kitchen. Also

do not use an ultrasonic humidier near the projector. Otherwise chlorine and minerals contained in tap water are atomized and could be deposited in the projector causing image degradation or other problems.

►

Position the projector to prevent light from directly hitting the projector's remote sensor. ►Do not place the product in a place where radio interference may be caused. ►Do not place this product in a magnetic eld. ►

If the projector is used at an altitude of about 1600 m or higher, set ALTITUDE of the SERVICE item in the OPTION menu to HIGH

(75). Otherwise, set it to NORMAL. If the projector is used with a wrong setting, it may cause damage to the projector itself or the parts inside. ►Do not touch the camera lens with your ngers.

NOTE

• The projector may make a rattling sound when tilted, moved or shaken, since a ap to control the air ow inside of the projector has moved. Be aware that this is not a failure or malfunction.

• The incoming light to the screen from the projector has a large angle. While the white image is on the screen, you may see it with colors, but this is because of the type of the screen used or the angles viewed, and it is not a malfunction.

• When the ambient temperature is around 35 to 40°C, the brightness of lamp is reduced automatically.

Setting up

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to conrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. After making sure that the device and projector are turned off, connect them following the instructions below.

►

WARNING

a re or damage to the device and the projector.

- Use only the accessories specified or recommended by the projector’s manufacturer. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. It may be regulated under some standard.

- For a cable with a core at only one end, connect the end with the core to the projector. That may be required by EMI regulations.

- Neither disassemble nor modify the projector and the accessories.

- Do not use the damaged accessory. Be careful not to damage the accessories. Route a cable so that it is neither stepped on nor pinched out.

CAUTION

in operation, unless that is directed in the manual of the device. Otherwise it may cause malfunction in the device or projector. ►Be careful not to mistakenly connect a connector to a wrong port. Otherwise it may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of the

projector are recessed.

Use only the appropriate accessories. Otherwise it could cause

►Do not turn on or off the projector while connected to a device

(continued on next page)

Setting up

Connecting with your devices (continued)

About Plug-and-Play capability

• Plug-and-Play is a system composed of a computer, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

Please use the standard drivers in your computer as this projector is a Plug-and-

Play monitor.

• When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in COMPUTER IN of the INPUT menu, that port will accept component video signals (

•

When the USB TYPE B port and the computer's type A USB port are connected,

51).

you can use the USB TYPE B port as a picture input port from the computer, use the remote control as a simple mouse and keyboard of the computer, or use the Interactive Function (22).

VCR/DVD/Blu-ray Disc

player

OUT

AUDIO

VIDEO

Cr/Pr

Cb/Pb

COMPONENT

HDMI

Smartphone Tablet

(continued on next page)

Computer

AUDIO

OUT

DISPLAY

RS-232C

USB

(A)

HDMI

Setting up

Connecting with your devices (continued)

NOTE

• Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600X1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

• If you connect this projector and a notebook computer, you need output the

display to an external monitor, or output simultaneously to the internal display and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this

projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (51).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display device. You may be able to see the dialog and set an appropriate display resolution.

(continued on next page)

Setting up

Connecting with your devices (continued)

• If you insert a USB storage device, such as a USB memory, into the USB TYPE A port and select the port as the input source, you can view images stored in the

device (116).

• You can connect a dynamic microphone to the MIC port with a 3.5 mm miniplug. In that case, the built-in speaker outputs the sound from the microphone, even while the sound from the projector is output. You can input line level signal to the MIC port from equipment such as wireless microphone. Select HIGH in the MIC LEVEL item of the AUDIO menu when you input line level audio signal to the MIC port. In the normal mode, the volume of the microphone can be adjusted separately from the volume of the projector using the menu. (62)

In the standby mode, the volume of the microphone is adjustable with the VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector. (27) Even when the sound of projector is set to mute mode by the AUDIO SOURCE function (61), the volume of the microphone is adjustable. In both modes (standby or normal), the AV MUTE button on the remote control works on the sounds of the microphone and the projector. (27)

Microphone

system

NOTE

Speakers

(with an amplier)

RGB IN

• If a loud feedback noise is produced from the speaker, move the

Monitor

microphone away from the speaker.

• This projector doesn't support plug-in power for the microphone.

(continued on next page)

Setting up

Connecting with your devices (continued)

To use network functions of the projector, connect the LAN port with the computer's LAN port, or with an access point that is connected to the computer with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, also connect the CONTROL port and an RS-232C port of the external device to communicate as a network terminal. See the User's Manual - Network Guide for details of the network functions.

CAUTION

Computer

RS-232C

USB TYPE A

LAN

►Before connecting the projector to a network system be sure

Access point

USB

wireless

adapter

(optional)

USB storage

device

to obtain the consent of the administrator of the network. ►

Do not connect the LAN port to any network that might have the excessive voltage.

►The designated USB wireless adapter that is sold as an option is required to use the wireless network function of this projector. ►Before removing the USB storage device from the port of the projector, be sure to use the REMOVE USB function on the thumbnail screen to secure your data (119). ►Do not use any extension cable or device when connecting the adapter to the projector. Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet. Do not touch the USB wireless adapter while the projector is receiving AC power. ►To connect both the LAN cable and USB device to the projector, use a LAN cable that is  at on the side where the plug’s wire is visible. Otherwise, both of them cannot be connected correctly, or the wire may break (malfunction).

(continued on next page)

Connecting with your devices (continued)

Setting up

NOTE

• If an oversized USB storage device blocks the LAN port, use a USB

extension cable to connect the USB storage device.

• The HDMI port of this model is compatible with HDCP (High-bandwidth Digital Content Protection) and therefore capable of displaying a video signal from HDCP compatible DVD players or the like.

- The HDMI supports the following signals.

For Video signals, refer to User’s Manual (detailed) Operating Guide – Technical.

Audio signal : Format Linear PCM Sampling frequency 48kHz / 44.1kHz / 32kHz

- This projector can be connected with another equipment that has HDMI

connector, but with some equipment the projector may not work properly, something like no video.

- Be sure to use an HDMITM cable that has the HDMITM logo.

- Use a Category 2-certied HDMITM cable to input 1080p@50/60 signal to the projector.

- When the projector is connected with a device having DVI connector, use a DVI to HDMITM cable to connect with the HDMI input.

- The MHL supports the following signals. For Video signals, refer to User’s Manual (detailed) Operating Guide – Technical. Audio signal : Format Linear PCM Sampling frequency 48kHz / 44.1kHz / 32kHz

- Be sure to use an MHL cable that has the MHL logo.

• Up to one USB wireless adapter (optional) can be connected to a projector.

Setting up

Connecting to a power supply

Put the connector of the power cord into the

AC (AC inlet) of the projector. Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

Please remember that when the DIRECT POWER ON function activated ( power supply make the projector turn on.

69), the connection of the

Power cord

WARNING

incorrect or faulty connections may result in re and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult

your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power

cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload

the outlet and connectors, loosen the connection, or result in re, electric shock or other accidents.

• Do not press the main body of projector on the power cord.

►Please use extra caution when connecting the power cord, as

Using the security bar and slot

A commercial anti-theft chain or wire up to 10 mm in diameter can be attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool.

Anti-theft chain or wire

WARNING

from falling down, since it is not designed for it.

CAUTION

It may become too hot.

►Do not use the security bar and slot to prevent the projector

►Do not place anti-theft chain or wire near the exhaust vents.

Security slot

Security bar

NOTE

measures. It is intended to be used as supplemental theft prevention measure.

• The security bar and slot is not comprehensive theft prevention

Using the cable cover

Utilize the cable cover as the guard and blind for the connecting parts.

Connect the signal cables and the power cord to the projector rst.

Insert the three knobs on the cable cover into the

three holes on the projector as shown in the gure. Pass the cables through the holes on the bottom of the cable cover.

Setting up

knobs

Fix the cover's screw.

CAUTION

prevent damage to the cables. ► Use the cable cover that is supplied with the projector. Do not attempt any modications to the cable cover.

► Be careful not to pinch the cables in the cable cover, to

screw

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Remove the battery cover.

Align and insert the two AA batteries (Use the appropriate

AA carbon-zinc or alkaline batteries (nonrechargeable) in accordance with laws and regulations.) according to their plus and minus terminals as indicated in the remote control.

Put the battery cover back to the former state.

WARNING

directed. Improper use may result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a

battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

►Always handle the batteries with care and use them only as

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

Remote control

Remote

sensor

30º

Approx.

3 m

NOTE

• You can deactivate one of the sensors using the REMOTE RECEIV.

item in the SERVICE menu of the OPTION menu (76) .

•

The remote control signal reected in the screen or the like may be available. If it is

difcult to send the signal to the sensor directly, attempt to make the signal reect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter uorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency. In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds.

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons (2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

FOCUS

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

KEYSTONE/

FREEZE

PERFECT FIT

TEMPLATE

ESC MENU

ENTER

POSITION

HDCR

D-ZOOM

VOLUME

＋

ー

(1)(2)

AV MUTE

RESET

Please remember that the REMOTE FREQ. in the SERVICE item of the OPTION menu

(77)

of the projector to be controlled should be set to the same mode as the remote control.

Remote control

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse and keyboard of the computer, when the projector’s USB TYPE B port and the computer’s type A USB port are connected.

(1) PAGE UP key: Press the PAGE UP button. (2) PAGE DOWN key: Press the PAGE DOWN button. (3) Mouse left button: Press theENTER button. (4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►. (5) ESC key: Press the ESC button. (6) Mouse right button: Press the RESET button.

NOTICE

►Improper use of the simple mouse & keyboard function could damage your equipment. While using this function, please connect this product only to a computer. Be sure to check your computer’s manuals before connecting this product to the computer.

USB TYPE B

port

(5)

(3)

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

FOCUS

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

KEYSTONE/

FREEZE

PERFECT FIT

TEMPLATE

ESC MENU

ENTER

POSITION

(1)

HDCR

D-ZOOM

VOLUME

＋

(2)

ー

AV MUTE

(4)

RESET

(6)

NOTE

When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

• When a USB cable connects this projector with a computer having a built-in pointing device (e.g. track ball) like a laptop PC, open BIOS setup menu, then select the external mouse and disable the built-in pointing device, because the built-in pointing device may have priority to this function.

•

Windows Vista® or higher is required for this function. And also this function may not work depending on the computer’s congurations and mouse drivers. This function can work with the computer which can operate general USB mouse or keyboard.

• You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

•

This function is activated only when the projector is working properly. This function is not available in any of the following cases:

- While the lamp is warming up. (The POWER indicator blinks in green.)

- When either USB TYPE A or USB TYPE B port is selected.

- While displaying BLANK

(27)

, TEMPLATE

(67)

or MY IMAGE screen.

- When any menu is displayed on the screen.

While using the cursor buttons to operate the sound or screen functions such as adjusting the sound volume, correcting the keystone, correcting the picture position and magnifying the screen.

Interactive pen

Installing the battery

1. Turn the battery cover of the pen to the left to open it.

As illustrated in the diagram, insert the AAA battery

into the battery cover with the - end facing the front. (Use the appropriate AAA alkaline batteries (non-rechargeable) in accordance with laws and regulations.)

3. Attach the battery cover by turning it to the right until it is completely closed.

• If you will not use the pen for long period, remove the batteries from the pen and store

them in a safe place.

• If the pen do not operate properly, change the batteries to other maker's product.

Exchanging the tip of the pen

When the tip of the pen is shortened due to wearing, exchange it according to the following procedure.

Remove the tip of the pen referring to the

illustration.

Fit a new tip into the place and push it so that it

clicks.

WARNING

►Always handle the batteries with care and use them only as

The tip of the pen

directed. Improper use may result in battery explosion, cracking or leakage, which could result in  re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries speci ed.

• Do not hold a battery with tweezers or the like.

• Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

• Do not place a battery in a  re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

• Keep the tip of the pen away from children and pets. Exercise care to prevent them from swallowing the tip of the pen or the pack of spare accidentally. If swallowed consult a physician immediately for emergency treatment.

CAUTION

►Do not drop the pen or mishandle it.

• Do not keep the tip of the pen directed to a bottom. It may cause damage, trouble and the consumption of the battery.

Power on/off

Turning on the power

Make sure that the power cord is rmly

and correctly connected to the projector and the outlet. Make sure that the POWER indicator is

steady orange (144). Press the STANDBY/ON button on the

projector or the remote control. The projection lamp lights up, and the POWER indicator begins to blink green. When the power is completely on, the indicator will stop blinking and light in steady green (144).

To display the picture, select an input signal according to the section Selecting an input signal (

28).

The INITIAL SETTING Menu will be displayed by factory default upon startup. Once the INITIAL SETTING Menu is set, it will not appear until FACTORY RESET

82) is executed. If you wish to change the settings, refer to the LANGUAGE

( (63) and ALTITUDE (75) menu.

(1) LANGUAGE: Use the ▲/▼/◄/►

buttons to select the desired language and press the ENTER button of the remote control or the button of the projector to execute.

STANDBY/ON button POWER indicator

IWB

INPUT

ASPECT

AUTO

FOCUS

PAGE

MAGNIFY

DOWNONOFF

KEYSTONE/ PERFECT FIT

TEMPLATE

ESC MENU

ENTER

POSITION

CALIBRATION

ACCENTUALIZER

HDCR

D-ZOOM

VOLUME

MYBUTTON

＋

ー

FREEZE

AV MUTE

RESET

(2) ALTITUDE: Use the ▲/▼ buttons to

select NORMAL for altitude below 1600 m (5250 feet), otherwise select HIGH and press the ENTER button of the remote control or the button of the projector to execute.

(continued on next page)

Power on/off

WARNING ►Never look into the projection window while the projection

lamp lights, since the projection lamp ray may cause a trouble on your eyes. ►Do not place the projector vertically. It could cause malfunction or injury. Tabletop use must be setup with the designated optional accessories. ►The projection window of this machine is made of glass. It can be damaged by excessive force or an impact. Read the following important warnings carefully, and follow them for your own safety.

• Do not apply excessive force on or allow impact to the projection window.

• Keep the projector out of the reach of children.

• If the projection window is broken, the projected image will be distorted. Never touch a broken projection window, and contact your dealer.

Power on/off

Turning off the power

Press the STANDBY/ON button on the projector or the remote control.

The message “Power off?” will appear on the screen for about 5 seconds.

Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (144).

Do not turn the projector on for about 10 minutes or more after turning it off. Also, do not turn the projector off shortly after turning it on. Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

WARNING

during use or just after use, since it is too hot. ►Remove the power cord for complete separation. The power outlet should be close to the projector and easily accessible.

NOTE

prior to the connected devices.

•

This projector has the function that can make the projector automatically turn

on/off. Please refer to the DIRECT POWER ON (70)

• Turn the power on/off in right order. Please power on the projector

items of the OPTION menu.

►Do not touch around the lamp cover and the exhaust vents

(69)

and AUTO POWER OFF

Operating

Adjusting the volume

Use the VOLUME +/VOLUME - buttons to adjust the volume.

A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after about ten seconds.

● When

is selected for current picture input port, the volume adjustment is

VOLUME +/- button

IWB

INPUT

ASPECT

AUTO

FOCUS

PAGE

MAGNIFY

DOWNONOFF

disabled. Please see AUDIO SOURCE item of AUDIO menu (61).

● Even if the projector is in the standby mode, the volume is adjustable when both of the following conditions are true:

- An option other than is selected for STANDBY in the AUDIO SOURCE item of the AUDIO menu (61).

NORMAL is selected in the STANDBY MODE item of the SETUP menu

● In the standby mode, the volume of the microphone is adjustable with the VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector (15).

Temporarily muting the screen and audio output

AV MUTE button

IWB

Press the AV MUTE button on the remote control.

The BLANK screen will be displayed instead of the screen of input signals and the sound from the AUDIO OUT port will be muted. Please refer to the BLANK item in SCREEN menu about the BLANK screen (63). To exit from the AV MUTE mode and restore the screen and audio, press the AV MUTE button again.

INPUT

ASPECT

PAGE

DOWNONOFF

KEYSTONE/

PERFECT FIT

AUTO

FOCUS

MAGNIFY

TEMPLATE

CALIBRATION

ACCENTUALIZER

D-ZOOM

MYBUTTON

(60).

CALIBRATION

ACCENTUALIZER

D-ZOOM

MYBUTTON

FREEZE

VOLUME

HDCR

VOLUME

AV MUTE

＋

ー

＋

ー

NOTE

• The projector automatically exits from the AV MUTE mode when

some control buttons are pressed.

•

The audio is output from the external audio system connected to the AUDIO OUT

port.

WARNING

►If you wish to have a blank screen while the projector's lamp is on, use the AV MUTE function above . Taking any other action may cause the damage on the projector. Blocking the beam by something causes high temperature and could result in re or smoke.

Operating

Selecting an input signal

Press the button on the projector.

Each time you press the button, the projector switches its input port from the current port as below.

COMPUTER IN1  COMPUTER IN2

INPUT button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

D-ZOOM

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

HDCR

INPUT button

＋

VIDEO LAN

HDMI

2 USB TYPE A

●

While ON is selected for AUTO SEARCH item in OPTION menu (69), the projector

HDMI 1/MHL  USB TYPE B

will keep checking the ports in above order repeatedly till an input signal is detected.

●

It may take several seconds to project the images from the USB TYPE B port.

Selecting an aspect ratio

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

 For a computer signal

NORMAL  4:3  16:9  16:10  NATIVE

 For HDMI

and MHL signal

NORMAL  4:3  16:9  16:10  14:9  NATIVE

 For a video signal or component video signal

4:3  16:9  16:10  14:9  NATIVE

 For an input signal from the LAN, USB TYPE A or USB TYPE B port, or

if there is no signal

16:10 (xed)

ASPECT button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

FOCUS

PAGE

MAGNIFY

DOWNONOFF

MYBUTTON

D-ZOOM

HDCR

VOLUME

＋

ー

● The ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

● The on-screen menu might be displayed outside of the image display area depending on the adjustment value of the ASPECT, D-ZOOM, KEYSTONE,

KEYSTONE and PERFECT FIT. Changing the values of ASPECT, D-ZOOM, KEYSTONE, KEYSTONE and PERFECT FIT may x the symptom.

Selecting an Interactive Function

Operating

Press the IWB button on the remote control. Displays the IWB MODE dialog.

Use the ◄/► cursor buttons to switch IWB MODE for the currently selected input port. Use the ▲/▼ cursor buttons to switch ON/OFF of FINGER TOUCH .

See the Interactive Function

(89)

Calibration

Press the CALIBRATION button on the remote control. Displays the CALIBRATION dialog. You can execute calibration of the Interactive Function in the CALIBRATION dialog.

See the Interactive Function

(89)

IWB button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

HDCR

D-ZOOM

FOCUS

PAGE

DOWNONOFF

MAGNIFY

MYBUTTON

VOLUME

CALIBRATION button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

HDCR

D-ZOOM

FOCUS

PAGE

DOWNONOFF

MAGNIFY

MYBUTTON

VOLUME

＋

ー

＋

ー

Operating

Adjusting the projector's elevator

The projector has 2pcs Rear foot for horizontals and inclinations. Spacers on the each elevator foot are installed at the time of shipment, and projector is in a condition to be able to just project. If necessary, detach the spacer, and the elevator feet can be manually twisted to make more precise adjustments.

-1~1°

Rear foot

Spacer

Rear foot

WARNING

►Keep the spacers away from children and pets. Be careful not to let them swallow the spacers. If swallowed, consult a physician immediately for emergency treatment.

-1~1°

NOTE

• The adjustment angle can be adjusted up to plus or minus 1° each of

foot.

•

After the foot is adjusted, it is possible to return it to the state of the shipment with a spacer. If change the setting place of the projector, it will recommend keep and reuse the spacers.

Adjusting the zoom and focus

Press the D-ZOOM + or D-ZOOM - button on the remote control to display D-ZOOM dialog on screen. Use the D-ZOOM + and D-ZOOM - buttons to adjust the picture size. To nish the operation, do not touch these buttons for about ten seconds until the dialog is disappeared.

● If you want to expand a part of the image, use the magnify function (34).

(continued on next page)

D-ZOOM - button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

HDCR

D-ZOOM

FOCUS

PAGE

DOWNONOFF

MAGNIFY

MYBUTTON

VOLUME

＋

ー

D-ZOOM + button

+ 129 hidden pages