Dukane 8755D-RJ, 8065, 8755D User Manual

Portable LCD Projector

Models 8755D, 8755D-RJ & 8065

USER’S MANUAL

401-8755D-01

Projector

CP-S24 /, 8755D-RJ, & 8065P-X250

8755D

User's Manual – Operating Guide

Thank you for purchasing this projector.

About this manual

Various symbols are used in this manual. The meanings of these symbols are
described below.

WARNING This symbol indicates information that, if ignored, could possibly

result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly

result in personal injury or physical damage due to incorrect
handling.

Please refer to the pages written following this symbol.



NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.

Trademark acknowledgment

• VGA and XGA are registered trademarks of International Business Machines Corporation.

• Apple and Mac are registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

All other trademarks are the properties of their respective owners.

1

2

Content

Content

About this manual . . . . . . . . . . 1

Content . . . . . . . . . . . . . . . . . . 2

Projector features . . . . . . . . . .

Preparations . . . . . . . . . . . . . .

3
3

About contents of package . . . . . . . 3

Fastening the lens cover . . . . . . . . . 3

Part names

. . . . . . . . . . . . . . . 4

Projector . . . . . . . . . . . . . . . . . . . . . 4

Control buttons . . . . . . . . . . . . . . . . 6

Remote control . . . . . . . . . . . . . . . . 6

Setting up . . . . . . . . . . . . . . . . 7

Arrangement . . . . . . . . . . . . . . . . . . 8

Adjusting the projector's elevator . . 9

Using the Security Bar . . . . . . . . . . 10

Connecting your devices . . . . . . . . .11

Connecting power supply . . . . . . . 14

Remote control . . . . . . . . . . .

15

Putting batteries . . . . . . . . . . . . . . 15

Using the remote control . . . . . . . . 16

Power on/off

Turning on the powe

. . . . . . . . . . . . . 17

r . . . . . . . . . . . 17

Turning off the power . . . . . . . . . . . 17

Operating . . . . . . . . . . . . . . . 18

Adjusting the volume . . . . . . . . . . . 18

Temporarily muting the sound . . . .

18

Selecting an input signal . . . . . . . . 18

Searcting an input signal . . . . . . . . 19

Selecting an aspect ratio . . . . . . . . 19

Adjusting the zoom and focus . . . . 19

Using the automatic adjustment feature

. 20

Adjusting the position . . . . . . . . . . 20

Correcting the keystone distortions 21

Using the magnify feature . . . . . . . 21

Freezing the screen . . . . . . . . . . . . 22

Temporarily blanking the screen

. . 22

Operating the computer screen . . . 23

Multifunctional settings . . . . 24

Using the menu function . . . . . . . . 24

EASY Menu . . . . . . . . . . . . . . . . . . 25

Aspect, Keystone, Mode, Brightness,
Contrast, Colo
Whispe
Language,
Go to advanced menu

r, Tint, Sharpness,

r, Mirror, Reset, Filter time,

PICTURE Menu . . . . . . . . . . . . . . . 27

Brightness, Contrast, Gamma,
Color temp, Colo
Progressive, My memory

r, Tint, Sharpness,

IMAGE Menu . . . . . . . . . . . . . . . . . 30

Aspect, Over scan, V. position, H. position,
H. phase, H. size, Auto adjust execute

INPUT Menu . . . . . . . . . . . . . . . . . 32

Color space, Component, Video format,
Frame lock, Information

SETUP Menu . . . . . . . . . . . . . . . . . 34

Keystone, Whisper, Mirror, Volume,
Audio

SCREEN Menu . . . . . . . . . . . . . . . 35

Language, Menu position, OSD bright.,
Blank, Start up, MyScreen,
MyScreen lock, Message

OPTION Menu . . . . . . . . . . . . . . . . 38

search, Auto off, Lamp time,

Auto

Filter time, Service

Maintenance . . . . . . . . . . . . . 40

Lamp . . . . . . . . . . . . . . . . . . . . . . . 40

Air filter

. . . . . . . . . . . . . . . . . . . . . 42

Other care . . . . . . . . . . . . . . . . . . . 44

Internal clock battery replacement

(8755D-RJ only) . . . . . . . . . . . 45

Troubleshootin

g . . . . . . . . . . 47

Related messages . . . . . . . . . . . . . 47

Regarding the indicator lamps . . . . 48

Phenomena that may easily be

mistaken for machine defects . . . . 50

Warranty and after-service

Specifications . . . . . . . . . . . .

8755D-RJ Network Functions &
Operation

Technical Information Section . . 97

. . . . . . . . . . . . . . . . . . 55

. . . 53

53

Projector features / Preparations

Projector features

This projector is used to project various computer signals as well as NTSC/PAL/
SECAM, Component (SD, HD) video signals onto a screen. It requires just a little
space for installation and gets a large image from short distance.

High Brightness



Newly developed 180W UHB (Ultra High Brightness) lamp gives you a higher
brightness image on a screen. The image can be still kept as bright and clean
enough for use in bright rooms.

Low Noise



WHISPER mode is available for reducing acoustic noise to realize quieter
operation. It is perfect for use in low luminance rooms where low noise is more
important than brightness.

Rich Connectivity



This projector has a variety of I/O ports. It can be easily connected to many
signal sources like PC, DVD and so on. The rich connectivity provides you
more options to make your presentation impressive.

Compact Body



Even with its many features, this projector is extremely compact and slim,
which gives you more flexibility and usability to use it where you want.

Preparations

About contents of package

Please see the "Contents of package" of the "User's Manual - Quick Guide". Your
projector should come with the items shown there. Contact immediately your
dealer if anything is missing.

NOTE

moving the projector, be sure to use the original packing materials

caution for the lens part.

• Keep the original packing materials for future reshipment. For
. Use special

Fastening the lens cover

To avoid losing the lens cover, please fasten it the lens cap to the projector using
the strap.

Strap ring

Strap

Fix the strap to the strap ring of the lens cover.

1.

Put the strap into the groove on the rivet.

2.

Push the rivet into the strap hole.

3.

Bottom side

Strap hole

3

4

Part names

Part names

Projector



Control buttons (6)

Lamp cover (41)
(Lamp unit is inside.)

Zoom knob (19)
Focus ring (19)

Vent (7)

Lens (17)

Front-Right side

Lens cover (3)



Bottom side

Remote sensor (16)

Speaker

Security bar (10)

Use for attaching a

（

commercial anti-theft
chain orwire.)

Elevator button (9)
Elevator foot (9)

Filter cover (42)
(Air filter and intake vent
are inside.)

WARNING ►During use or immediately after use, do not touch around the

lamp and vents of the projector. (

) It could cause a burn.

Part names

Power switch (17)

AC inlet (14)

Ports (See below.)

CONTROL port (12)

AUDIO-OUT po

rt (12)

AUDIO IN2 L/R port (13)
(In the default setting, the
AUDIO IN2 L/R port is the audio
port for the VIDEO, S-VIDEO
and COMPONENT VIDEO
ports, however it is possible to
change the settings. 34)

COMPONENT
VIDEO ports (13)

Y R

AUDIO IN

Y

B

CB/P

R

CR/P

VIDEO port (13)

C

B

/

P

C

R

/

P

VIDE

S-VIDEO

B

L

R

O

S-VIDEO port (13)

AUDIO IN1 port (12)
(In the default setting, the AUDIO
IN1 port is the audio port for the
RGB IN1 and RGB IN2 ports,
however, it is possible to change
the settings.





34)

Rear-Left side

Restart switch (*) (48)

2

CONTROL RGB IN

AUDIO OU

T

AUDIO IN

1

LINK O
ACT O

Elevator button (9)

Elevator foot (9)

Vent (7)

RGB IN1

port (12)

RGB IN2 /RGB OUT port

(12)
(Use the RGB IN OUT switch to select
RGB IN2 or RGB OUT for this port.)
RGB IN2 port: Inputs the RGB signal from
a PC.
RGB OUT port: When connected to a
monitor, outputs the signal input via RGB
IN1.

1

RGB IN

2

RGB OU

USB

T

K

USB port (12)

Ports

RGB IN OUT switch

(12)
Use this button to select either RGB IN2
or RGB OUT for the corresponding port.
When this switch is not pushed in, RGB
IN2 is selected.
When this switch is pushed in, RGB OUT
is selected.

LAN Port (

12)



RJ-45 Jack,

Model 8755D-RJ Only!

Used for Ethernet input/output.
This port is used when utilizing network functions.

NOTE (*) About Restart switch: This projector is controlled by an internal
microprocessor. Under certain exceptional circumstances, the projector may not
operate correctly and the microprocessor will need to be reset. In such a case,
please push the Restart switch by using a tooth pick or similar, and before
turning on again, let the projector cool down at least 10 minutes without

operating. Only push the Restart switch in these exceptional instances.

5

6

Part names

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

KEYSTONE

POSITION

ES

C

ENTE

R

MENU

RESE

T

Control buttons

Cursor buttons
▲,▼,◄,►(24)

STANDBY/ON button

(17)

Remote control

LAMP indicator (46, 47)

TEMP indicator

(46, 47)

POWER indicator (17)

INPUT button (18)

SEARCH button (19)

RGB button (18)

VIDEO button (19)

ASPECT button

HOME button (23)

MAGNIFY
ON button (21)
OFF button (21)

END button (23)

FREEZE button (22)

POSITION button (20)

ESC button (24)

Battery cover (15)
(on the back)

(19)

STANDBY/ON button

AUTO

button (20)

BLANK button (22)

PAGE UP

button (23)

VOLUME button (18)

MUTE button (18)

PAGE

DOWN button (23)

KEYSTONE button

MENU button (24)

Cursor buttons

▲,▼,◄,► (24)

ENTER button (24)

RESET button

(17)

(21)

(24)

Setting up

Setting up

WARNING ►Place the projector in a stable position horizontally. A fall or

a turnover could cause an injury and/or damage to the projector. Using a
damaged projector could result in a fire and/or an electric shock.

• Do not place the projector on an unstable, slant or vibrant surface such as a

wobbly or inclined stand.

• Do not place the projector in the side/front/rear-up position, except when

cleaning the air filter.

►Place the projection in a cool place, and pay attention enough to ventilation.
The high temperature of the projector could cause a fire, a burn and/or
malfunction to the projector.

• Do not stop up, block and cover the projector's vents.

• Keep a space of 30 cm or more between the sides and other objects such as

walls.

• Do not place the projector on a metallic thing or anything weak in heat.

• Do not place the projector on a carpet, cushion or bedding.

• Do not place the projector in direct sunlight or near a hot object such as a

heater.

• Put nothing about lens and vents of the projector. Put nothing on the projector.

• Put nothing that is sucked or sticks to the bottom of projector. This projector

has some intake vents also on the bottom.
►Do not place the projector on the place that gets wet. Damping the projector
or inserting liquid in the projector could cause a fire, an electric shock and/or
malfunction to the projector.

• Do not place the projector in a bathroom or the outdoors.

• Put nothing containing the liquid near the projector.

CAUTION ►Avoid a smoky, humid or dusty place. Placing the projector
in such place could cause a fire, an electric shock and/or malfunction to the
projector.

• Do not place the projector near a humidifier, a smoking space or a kitchen.
►Adjust the direction of the projector to keep the light from directly hitting the
projector's remote sensor.

7

8

Setting up

Arrangement

Refer to the illustrations and tables below to determine the screen size and projection distance.
The values shown in the table are calculated for a full size screen: TBD : 800×600,

8755D : 1024×768
(a) The screen size (diagonal)
(b) Distance from the projector to the screen (±10%)
(c) The height of the screen (±10%)

(c) up

(c) down

(a)

4:3

16:9

(a)

For the model 8065

(a) Screen

size

[inch (m)]

30 (0.8) 0.9 (36)
40 (1.0) 1.2 (48) 1.5 (57) 6 (2) 55 (22) 1.3 (52) 1.6 (63) -2 (-1) 51 (20)
50 (1.3) 1.5 (60) 1.8 (72) 8 (3) 69 (27) 1.7 (65) 2.0 (79) -2 (-1) 64 (25)
60 (1.5) 1.8 (72) 2.2 (87) 9 (4) 82 (32) 2.0 (79) 2.4 (94) -2 (-1) 77 (30)
70 (1.8) 2.1 (84) 2.6 (101) 11 (4) 96 (38) 2.3 (92) 2.8 (110) -3 (-1) 90 (35)
80 (2.0) 2.4 (96) 2.9 (116) 12 (5) 110 (43) 2.7 (105) 3.2 (126) -3 (-1) 103 (41)

90 (2.3) 2.8 (109) 3.3 (130) 14 (5) 123 (49) 3.0 (118) 3.6 (142) -4 (-1) 116 (46)
100 (2.5) 3.1 (121) 3.7 (145) 15 (6) 137 (54) 3.3 (132) 4.0 (158) -4 (-2) 129 (51)
120 (3.0) 3.7 (145) 4.4 (174) 18 (7) 165 (65) 4.0 (158) 4.8 (190) -5 (-2) 154 (61)
150 (3.8) 4.6 (182) 5.5 (218) 23 (9) 206 (81) 5.0 (198) 6.0 (238) -6 (-2) 193 (76)
200 (5.1) 6.2 (242) 7.4 (291) 30 (12) 274 (108) 6.7 (264) 8.1 (317) -8 (-3) 257 (101)
250 (6.4) 7.7 (303) 9.3 (364) 38 (15) 343 (135) 8.4 (330) 10.1 (397) -10 (-4) 322 (127)
300 (7.6) 9.2 (364) 11.1 (437) 46 (18)

(b) Projection distance

[m (inch)]

min.

4 : 3 screen

max. down

1.1 (43)

5 (2)

(c) Screen height

[cm (inch)]

up min. max.

41 (16)

411

(b) Projection distance

1.0 (39) 1.2 (47)

(162)

10.1 (397) 12.1 (476)

[m (inch)]

For the model 8755D & 8755D-RJ

(a) Screen

size

[inch (m)]

30 (0.8) 0.9 (36) 1.1 (43)

40 (1.0) 1.2 (48) 1.5 (58) 6 (2) 55 (22) 1.3 (52) 1.6 (63) -2 (-1) 51 (20)

50 (1.3) 1.5 (60) 1.8 (73) 8 (3) 69 (27) 1.7 (66) 2.0 (79) -2 (-1) 64 (25)

60 (1.5) 1.8 (73) 2.2 (87) 9 (4) 82 (32) 2.0 (79) 2.4 (95) -2 (-1) 77 (30)

70 (1.8) 2.2 (85) 2.6 (102) 11 (4) 96 (38) 2.4 (93) 2.8 (111) -3 (-1) 90 (35)

80 (2.0) 2.5 (97) 3.0 (117) 12 (5) 110 (43) 2.7 (106) 3.2 (127) -3 (-1) 103 (41)

90 (2.3) 2.8 (109) 3.3 (132) 14 (5) 123 (49) 3.0 (119) 3.6 (143) -4 (-1) 116 (46)
100 (2.5) 3.1 (122) 3.7 (146) 15 (6) 137 (54) 3.4 (133) 4.0 (159) -4 (-2) 129 (51)
120 (3.0) 3.7 (146) 4.5 (176) 18 (7) 165 (65) 4.0 (159) 4.9 (192) -5 (-2) 154 (61)
150 (3.8) 4.6 (183) 5.6 (220) 23 (9) 206 (81) 5.1 (200) 6.1 (240) -6 (-2) 193 (76)
200 (5.1) 6.2 (244) 7.5 (294) 30 (12) 274 (108) 6.8 (266) 8.1 (320) -8 (-3) 257 (101)
250 (6.4) 7.8 (306) 9.3 (367) 38 (15) 343 (135) 8.5 (333) 10.2 (400) -10 (-4) 322 (127)
300 (7.6) 9.3 (367) 11.2 (441) 46 (18)

(b) Projection distance

[m (inch)]

min.

4 : 3 screen

(c) Screen height

max. down

5 (2)

[cm (inch)]

41 (16)

411

(b) Projection distance

up

(162)

min.

1.0 (39) 1.2 (47)

10.2 (400) 12.2 (480)

[m (inch)]

max. down up

(b)

16 : 9 screen

(c) Screen height

[cm (inch)]

down up

-1 (0) 39 (15)

-12 (-5) 386 (152)

16 : 9 screen

(c) Screen height

[cm (inch)]

-1 (0) 39 (15)

-12 (-5) 386 (152)

Setting up

Adjusting the projector's elevator

CAUTION ►If you press the elevator button without holding the projector,

the projector might crash down, overturn, smash your fingers and possibly
result in malfunction. To prevent damaging the projector and injuring yourself,
always hold the projector whenever using the elevator buttons to adjust the
elevator feet.
►Do not incline the projector rightward or leftward. Also do not incline it
backward or forward exceeding 9 degrees. Exceeding these range could cause
malfunction, and could shorten the lifetime of the consumables.
►Except for inclining by the elevator feet adjustment, place the projector
horizontally.

You can use the elevator feet to make adjustments if the surface on which you
need to set the projector is uneven or if you otherwise need to adjust the angle of
projection. The adjustment range of the elevator feet is 0 to 9 degrees.

Elevator feet

After making sure that the projector is cool adequately, press and hold in the

1.

elevator buttons while holding the projector.

The elevator buttons and the elevator feet are on the both sides.

Raise or lower the projector to the desired height and release the elevator

2.

buttons.

When you release the elevator buttons, the elevator feet will lock into position.

If necessary, you can also finely adjust the height of the projector by twisting

3.

the elevator feet by hand.

Elevator button

9

10

Setting up

Using the Security Bar

WARNING ►Do not use the security bar to prevent the projector from

falling. Dropping or knocking over the projector may cause damage or injury.

CAUTION ►The security bar is not a comprehensive theft prevention

measure. It is intended to be used as an extra theft prevention measure.

A commercial anti-theft chain or wire can be attached to the security bar on the
projector.

How to attach

1.

An anti-theft chain or wire can be
attached as shown in the illustration.
(Anti-theft chains or wires of up to
10mm in diameter can be used)

Security Bar

Anti-theft chain or wire
[sold separately]

Setting up

Connecting your devices

CAUTION ►Turn off all devices prior to connecting them to the projector.

Attempting to connect a live device to the projector may generate extremely
loud noises or other abnormalities that may result in malfunction and/or damage
to the device and/or projector.
►Use the accessory cable or a designated-type cable for the connection.
Some cables have to be used with core set. A too long cable may cause a
certain picture degradation. Please consult with your dealer for details. For
cables that have a core only at one end, connect the core to the projector.
►Make sure that you connect devices to the correct port. Incorrect connection
may result in malfunction and/or damage to the device and/or projector.

NOTE • Whenever attempting to connect a laptop computer to the projector, be sure
to activate the laptop’s RGB external image output (set the laptop to CRT display or to
simultaneous LCD and CRT display). For details on how this is done, please refer
instruction manual of the corresponding laptop computer.

• Secure the screws on the connectors and tighten.

• Some computers may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.

• For some RGB signal modes, the optional Mac adapter is necessary.

• When the image resolution is changed on a computer, depending on an input,
automatic adjustment function may take some time and may not be completed. In this
case, you may not be able to see a check box to select “Yes/No” for the new resolution
on Windows. Then the resolution will go back to the original. It might be recommended
to use other CRT or LCD monitors to change the resolution.

About Plug-and-Play capability

Plug-and-Play is a system composed of the computer, its operating system and
peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC
2B. Plug-and-Play can be achieved by connecting this projector to a computer is VESA
DDC (display data channel) compatible.

• Please take advantage of this function by connecting the accessory RGB cable to the
RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other
type of connection is attempted.

• Please use the standard drivers in your computer as this projector is a Plug-and-Play
monitor.

to the

11

12

Setting up

Y R

L

AUDIO IN

2

AUDIO OU

T

CONTROL RGB IN

1

RGB IN

2

USB

RGB OU

T

AUDIO IN

1

VIDE

O

S-VIDEO

C

B

/

P

B

C

R

/

P

R

K

Y R

L

AUDIO IN

2

AUDIO OU

T

CONTROL RGB IN

1

RGB IN

2

USB

RGB OU

T

AUDIO IN

1

VIDE

O

S-VIDEO

C

B

/

P

B

C

R

/

P

R

K

Y R

L

AUDIO IN

2

AUDIO OU

T

CONTROL RGB IN

1

RGB IN

2

USB

RGB OU

T

AUDIO IN

1

VIDE

O

S-VIDEO

C

B

/

P

B

C

R

/

P

R

K

Y R

L

AUDIO IN

2

AUDIO OU

T

CONTROL RGB IN

1

RGB IN

2

USB

RGB OU

T

AUDIO IN

1

VIDE

O

S-VIDEO

C

B

/

P

B

C

R

/

P

R

K

RGB IN2

RGB OUT

Examples of connection with a computer

* In the default setting, the AUDIO IN1 port is the audio port for the RGB IN1 and RGB IN2
ports. To change the settings, refer to the AUDIO item in the SETUP menu.

RGB cable

USB cable

(34)

RGB out

Stereo mini
audio cable

Audio out RS-232C

USB

RS-232C cable

Stereo mini audio cable

RGB out

Connecting to a monitor (output)

Audio out

RGB cable

Use the RGB IN OUT switch to select RGB OUT
(RGB OUT is selected if the

RGB in

RGB cable

Connecting to a speaker with amplifier (output)

Audio in

Use the RGB IN OUT
switch to select
RGB IN2 (RGB IN2 is
selected if the switch is
not pushed in).

is pushed in).

switch

Stereo mini audio cable

Y R

L

AUDIO IN

2

AUDIO OUT

CONTROL RGB IN

1

RGB IN

2

USB

RGB OU

T

AUDIO IN

1

VIDE

O

S-VIDEO

CB/PB

CR/PR

K

Y R

L

AUDIO IN

2

AUDIO OUT

CONTROL RGB IN

1

RGB IN

2

USB

RGB OU

T

AUDIO IN

1

VIDE

O

S-VIDEO

C

B

/

P

B

CR/PR

K

Y R

L

AUDIO IN

2

AUDIO OUT

CONTROL RGB IN

1

RGB IN

2

USB

RGB OU

T

AUDIO IN

1

VIDE

O

S-VIDEO

CB/PB

CR/PR

K

Setting up

Y R

L

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2

USB

RGB OU

T

AUDIO IN1

LAN

LINK

ACT

VIDE

O

S-VIDEO

C

B

/

P

B

C

R

/

P

R

K

Examples of connection with a VCR/DVD player

*

In the default setting, the AUDIO IN2 L/R port is the audio port for the VIDEO, S-VIDEO
and COMPONENT VIDEO ports. To change the settings, refer to the AUDIO item in the
SETUP menu.

(34)

Audio (R) out

Audio (L) out

Video out

Audio (R) out

Audio (L) out

Audio/Video

Audio cable

cable

Component video out

Audio (R) out

Audio (L) out

8755D-RJ Only!

S-Video

Y

CB/P

B

CR/P

R

out

S-Video

cable

Component video cable

Audio cable

13

14

Setting up

Connecting power supply

WARNING ►Please use extra caution when connecting the power cord, as

incorrect or faulty connections may result in fire and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, contact
your dealer to newly get correct one.

• Only plug the power cord into an outlet rated for use with the power cord's
specified voltage range.

• Never modify the power cord. Never attempt to defeat the ground connection
of the three-pronged plug.

AC inlet

Connector
of the power cord

Connect the connector of the power cord to the AC inlet of the projector.

1.

Firmly plug the power cord's plug into the outlet.

2.

Remote control

Remote control

Putting batteries

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fire, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specified. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

•

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.
Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

•

•

If you observe a leakage of a battery, wipe out the flower and then replace a battery.

If the liquid adheres to your body or clothes, rinse well with water immediately.

Remove the battery cover.

1.

Slide back and remove the battery cover in the direction of the arrow.

I

nsert the batteries.

2.

Align and insert the two AA batteries according to their plus and minus
terminals as indicated in the remote control.

Close the battery cover.

3.

Replace the battery cover in the direction of the arrow and snap it back into place.

15

Remote control

Using the remote control

CAUTION ►Be careful in handling the remote control.

• Do not drop or expose the remote control to physical impact.

• Do not get the remote control wet or place it on wet objects. It may result in

malfunction.

• Remove the batteries from the remote control and store them in a safe place if

you won’t be using the remote control for an extended period.

• Replace the batteries whenever the remote control starts malfunctioning.

• When strong lights (such as direct sunlight) or light from an extremely close

range (such as from an inverter fluorescent lamp), hit the projector’s remote
sensor, the remote control may cause to function. Adjust the direction of the
projector to keep the light from directly hitting the projector’s remote sensor.

The remote control works with the projector’s remote sensor.

30º

30º

approx. 3 meters

• The range of the remote sensor is 3 meters with a 60 degree range (30 degrees
to the left and right of the remote sensor).

• Also a remote signal reflected in the screen etc. may be available. If it is difficult
to send a remote signal to the sensor directly, please try to use the reflected signal.

• Since the remote control uses infrared light to send signals to the projector
(Class1 LED), be sure to use the remote control in an area free from obstacles
that could block the remote control’s output signal to the projector.

16

Power on/off

HOME

PAGE UP

PAGE DOWN

EN

D

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUT

O

BLAN

K

MUTE

VOLUME

KEYSTONE

POSITION

ES

C

ENTE

R

MENU

RESE

T

Power on/off

WARNING ►When the power is on, a strong light is emitted. Do not look into

the lens of projector. Also do not peep at the inside of projector through a hole.

NOTE •

Turn the power on/off in right order. Please power on the projector prior

to the connected devices. Power off the projector later than the connected devices.

Turning on the power

Make sure that the power cord is firmly and

1.

correctly connected to the projector and the

STANDBY/ON
button

outlet.

Remove the lens cover, and set the power

2.

switch to the ON position.
The power indicator will light up in steady orange.
Then wait several seconds because the buttons
may not function for these several seconds.

Press the STANDBY/ON button on the projector or the remote control.

3.

The projector lamp will light up and the POWER
indicator will begin blinking in green. When the power is
completely on, the indicator will stop blinking and light in
green.

To display the picture, select an input signal according to
the section "Selecting an input signal"

(18)

.

Turning off the power

This product is able to turn off the main power during the cooling. However, please
pay special attention to below two points when you do:

(1) Please do not turn the projector on again for at least 1 minute in this case.

Neglect could shorten the lifetime of the lamp.

(2) During use or immediately after use, do not touch around the lamp and vents

of the projector

Press the STANDBY/ON button on the projector or the remote control.

1.

The message "Power off?" will appear on the screen for approximately 5
seconds.

Press the STANDBY/ON button on the projector or the

2.

remote control again while the message appears.
The projector lamp will go off, and the POWER indicator will
begin blinking in orange.

Then the POWER indicator will stop blinking and light in
steady orange when the lamp cooling is complete.

Make sure that the power indicator lights in steady orange,

3.

and set the power switch to the OFF position. The POWER

indicator will go off. Attach the lens cover.

(4 )

It could cause a burn.

P

OWER

indicator

POWER

(Steady orange)

POWER

(Blinking in green)

POWER

(Steady

green)

Power off?

POWER

(Blinking in

(

Steady

orange)

POWER

orange)

17

18

Operating

HOME

PAGE UP

PAGE DOWN

VIDEO

RG

B

SEARC

H

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

KEYSTONE

VIDEO

RG

B

SEARC

H

ASPECT AUTO

BLAN

K

Operating

Adjusting the volume

Press the VOLUME button on the remote control.

1.

A dialog will appear on the screen to aid you in adjusting the volume.

Use the cursor buttons ▲/▼ to adjust the volume.

2.

To close the dialog and complete the operation, press the
VOLUME button again. Even if you don’t do anything, the
dialog will automatically disappear after a few seconds.

Temporarily muting the sound

Press the MUTE button on the remote control.

1.

A dialog will appear on the screen indicating that you have muted the sound.
To restore the sound, press the MUTE or VOLUME button.

Even if you don’t do anything, the dialog will automatically
disappear after a few seconds.

Selecting an input signal

Press the INPUT button on the projector.

1.

Each time you press the button, the projector switches its
input port as below.

RGB IN1  RGB IN2
VIDEO  S-VIDEO  COMPONENT VIDEO

● When the RGB IN2/RGB OUT port functions as an RGB out
port (the RGB IN OUT switch is pushed in), RGB IN2 cannot
be selected. In that case “RGB2/RGB OUT  RGB OUT” message will be
displayed.

Press the RGB button on the remote control to select an

1.

input port for the RGB signal.
Each time you press the button, the projector switches its RGB
input port as below.

RGB IN1  RGB IN2

● If the RGB button is pushed (when switching from VIDEO to RGB signals)
when TURN ON is selected for the AUTO SEARCH item in the OPTION menu
the projector will check the RGB IN1 port first.

If no input is detected at the port,

the projector will check the RGB IN2 port.

● When the RGB IN2/RGB OUT port functions as an RGB out port (the RGB IN
OUT switch is pushed in), RGB IN2 cannot be selected. In that case

RGB OUT” message will be displayed.



RGB OUT

“RGB2/

Operating

HOME

PAGE UP

VIDEO

RG

B

SEARC

H

ON

MAGNIFY

ASPECT AUT

O

BLAN

K

VOLUME

VIDEO

RG

B

SEARC

H

ASPECT AUT

O

BLAN

K

VIDEO

RG

B

SEARC

H

ASPECT AUT

O

BLAN

K

Selecting an input signal

1

.

Press the
input for

VIDEO

video signal

Each time you press

as below

port

input

video
COMPONENT VIDEO

(continued)

button on the remote contro

.

button, th

the



.

S-VIDEO

e projector switche

VIDEO



l

to select an

s

its

If the VIDEO button is pushed (when switching from RGB to VIDEO signals)

●
when TURN ON is selected for the AUTO SEARCH item in the OPTION menu
the projector will check the COMPONENT VIDEO port first.

port, projector will begin to check other ports in above order.

detected at

the

If no input is

Searching an input signal

Press the SEARCH button on the remote control.

1.

The projector will start to check its input ports in order to
find any input signals.
Then when an input is found, the projector will stop searching and display the
image. If no signal is found, the projector will return to the state selected before
the operation.

RGB IN 1  RGB IN 2

COMPONENT VIDEO



Selecting an aspect ratio

Press the ASPECT button on the remote control.

1.

Each time you press the button, the projector switches the mode for aspect
ratio in turn.

For an RGB signal



NORMAL  4:3  16:9

For a video signal/no signal



4:3  16:9  SMALL

● The NORMAL mode keeps the original aspect ratio of the signal.

● For an HDTV signal of 1125i (1080i) or 750p (720p) as the COMPONENT
VIDEO input, only 16:9 mode can be selected.

● Performing the automatic adjustment initializes the aspect ratio setting.

S-VIDEO  VIDEO



Adjusting the zoom and focus

Use the zoom knob to adjust the screen size.

1.

Use the focus ring to focus the picture.

2.

Focus ring

Zoom knob

19

20

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

KEYSTONE

POSITION

MENU

HOME

PAGE UP

VIDEO

RG

B

SEARC

H

ON

MAGNIFY

ASPECT AUTO

BLAN

K

VOLUME

Using the automatic adjustment feature

Press the AUTO button on the remote control.

1.

For an RGB signal



The vertical position, the horizontal position, the clock phase
and the horizontal size will be automatically adjusted.
And the aspect ratio will be automatically selected. Make sure that the
application window is set to its maximum size prior to attempting to use this
feature. A dark picture may still be incorrectly adjusted. Use a bright picture
when adjusting.

For a video signal or s-video signal



The video format best suited for the respective input signal will be selected
automatically.
This function is available only when the AUTO mode is selected to the
VIDEO FORMAT item in the INPUT menu
signal, the signal type is identified automatically independently of this
function.

For a video signal, s-video signal or component video signal



The vertical position and horizontal position will be automatically adjusted.

For a component video signal



The aspect ratio will be automatically selected.
The clock phase will be automatically adjusted.

● The automatic adjustment operation requires approximately 10 seconds. Also

please note that it may not function correctly with some input.

(32)

. For a component video

Adjusting the position

Press the POSITION button on the remote control.

1.

The “POSITION” indication will appear on the screen.
Use the cursor buttons ▲/▼/◄/► to adjust the picture

2.

position.

When you want to reset the operation, press the RESET button on the remote
control during the operation.

To complete this operation
do anything, the dialog will automatically disappear after a few seconds.

● When this function is performed at a video signal, a certain extra such as a line
may appear outside a picture.

, press the POSITION button again. Even if you don’t

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

KEYSTONE

HOME

PAGE UP

VIDEO

RG

B

SEARC

H

ON

MAGNIFY

ASPECT AUTO

BLAN

K

VOLUME

Correcting the keystone distortions

Press the KEYSTONE button on the remote control. A

1.

dialog will appear on the screen to aid you in correcting the

distortion.

Use the cursor buttons ▲/▼ to correct the distortion.

2.

To close the dialog and complete this operation, press the

KEYSTONE button again.

Even if you don’t do anything, the

dialog will automatically disappear after a few seconds.

● The adjustable range for correction will vary among inputs. For some input, this
function may not work well.

● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the
SETUP menu, if the projector screen is inclined or angled downward, this
function may not work correctly.

● When the zoom adjustment is set to the TELE (telephoto focus), this correction
may be excessive. This function should be used when the zoom adjustment is
set to the WIDE (wide-angle focus) whenever possible.

Using the magnify feature

Press the ON button of MAGNIFY on the remote control.

1.

The “MAGNIFY” indication will appear on the screen
(although the indication will disappear in several seconds with
no operation), and the projector will enter the MAGNIFY mode.

Use the cursor buttons ▲/▼ to adjust the zoom level.

2.

To move the zoom area
then use the cursor buttons ▲/▼/◄/► to move the area. And to finalize the
zoom area, press the POSITION button again.

To exit the MAGNIFY mode and restore the screen to normal, press the O
button of MAGNIFY on the remote control.

● The projector automatically exits the MAGNIFY mode when the input signal is
changed, or when the display condition is changed.

● Although in the MAGNIFY mode, the keystone distortion condition may vary, it
will be restored when the projector exits the MAGNIFY mode.

, press the POSITION button in the MAGNIFY mode,

FF

21

22

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

KEYSTONE

HOME

PAGE UP

VIDEO

RG

B

SEARC

H

MAGNIFY

ASPECT AUTO

BLAN

K

VOLUME

Freezing the screen

Press the FREEZE button on the remote control.

1.

The “FREEZE” indication will appear on the screen, and the

projector will enter the FREEZE mode.
To exit the

FREEZE mode and restore the screen to normal,

press the FREEZE button again.

● The projector automatically exits the FREEZE mode when the input signal
changes, or when one of the projector’s buttons or the remote control buttons
of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME,
MUTE, KEYSTONE, POSITION and MENU is pressed.

● If the projector continues projecting a still image for long time, the LCD panel
might possibly be printed. Do not leave the projector in the FREEZE mode for
too long.

Temporarily blanking the screen

Press the BLANK button on the remote control.

1.

The blank screen will be displayed instead of the screen of

input signal. Please refer to the BLANK item in the SCREEN

(35).

menu
To exit the blank screen and return to the input signal screen, press the

BLANK button again.

● The projector automatically returns to the input signal screen when the input
signal is changed, or when one of the projector’s buttons or the remote control
buttons is pressed.

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

KEYSTONE

POSITION

ES

C

ENTE

R

MENU

RESE

T

Operating the computer screen

CAUTION ►Mistaken use of the mouse/keyboard control could damage

your equipment.

• While using this function, please connect only with a computer.

• Before connecting, read the manuals of the computer you will connect.

NOTE • It may not be possible to control notebook PC, and other computers with
built-in pointing device (e.g. track ball), using this remote control. In this case, before
connecting go into BIOS (system setup) and select external mouse, and disable the
pointing device. In addition, the mouse may not function if the computer does not have
the needed utility program. See your computer’s hardware manual for details.

• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be
possible to use the remote control, depending on the computer’s configurations and
mouse drivers.

• The USB control can be used only for the functions listed below. You cannot do things
like press two buttons at once (for instance, pressing two buttons at the same time to
move the mouse pointer diagonally).

• This function is not available while the lamp is warming up (the POWER indicator
flashes green), and while adjusting the volume and display, correcting for trapezoidal
distortion, zooming in on the screen, using the BLANK function, or displaying the menu

screen.

USB mouse and keyboard control

Connect the projector’s USB port to the computer via the mouse cable.

1.

Available function Remote control operation

Move pointer Use ▲, ▼, ◄, ► buttons

Left click with mouse Press ENTER button

Right click with mouse Press RESET button

Press keyboard’s HOME key

Press keyboard’s END key

Press HOME button

Press END button

Press keyboard’s PAGE UP key Press PAGE UP button

Press keyboard’s PAGE DOWN key

Press keyboard’s ESC key

Press PAGE DOWN button

Press ESC button

23

Multifunctional settings

 EASY MENU

 ASPECT             4:3

+0

+0

+0
+0
+0
 3

 Go To Advance Menu...

NORMAL

NORMAL
NORMAL

0h
ENGLISH

KEYSTONE
MODE
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
WHISPER
MIRROR
RESET
FILTER TIME
LANGUAGE

 MENU [RGB]

 IMAGE

 SETUP

 PICTURE

 INPUT

 OPTION

 SCREEN

 SHARPNESS        3

BRIGHTNESS     ＋0
 CONTRAST       ＋0

COLOR           +0
 TINT            +0

 COLOR TEMP   MIDDLE

 GAMMA        DEFAULT 1

 MY MEMORY    SAVE 1

   :SELECT

 EASY MENU

 PROGRESSIVE  TURN OFF

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

KEYSTONE

POSITION

ES

C

ENTE

R

MENU

RESE

T

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RG

B

SEARC

H

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLAN

K

MUTE

VOLUME

KEYSTONE

POSITION

ES

C

ENTE

R

MENU

RESE

T

Multifunctional settings

Using the menu function

This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN,
OPTION, and EASY MENU. EASY MENU cosists of functions often used, and the
other menus are classified into each purpose. Each of these menus is operated using
the same methods. The basic operations of these menus are as follows.

MENU button

ENTER button

Cursor buttons

RESET button

Press the MENU button on the remote control or one of

1.

the cursor buttons on the projector.

The Advanced MENU or EASY MENU will appear.

In the EASY MENU

If you want to change it to the Advanced MENU, select the

2.

"Go to Advanced Menu"
Use the cursor buttons ▲/▼ to select an item to operate.

3.

Use the cursor buttons◄/► to operate the item.

4.

In the Advanced MENU

Use the cursor buttons ▲/▼ to select a menu.

2.

If you want to change it to the EASY MENU, select the
EASY MENU.
Then press the cursor button ► on the projector or remote
control, or the ENTER button on the remote control to select
an item. The display of the selected menu will be active.

Use the cursor buttons ▲/▼ to select an item to operate.

3.

Then press the cursor button ► on the projector or remote control, or the ENTER button
on the remote control to progress. The operation menu of the selected item will appear.

Use the cursor buttons▲/▼ to operate the item.

4.

●

When you want to reset the operation, press the RESET button on the remote control
during the operation. Note that items whose functions are performed simultaneously
with operation (ex. LANGUAGE, H PHASE, VOLUME etc.) cannot be reset.

●

In the advanced menu, when you want to return to the previous display, press the cursor
button ◄ on the projector or remote control, or the ESC button on the remote control.

Press the MENU button on the remote control again to close the menu

5.

and complete this operation. Even if you don't do anything, the dialog will
automatically disappear after about 10 seconds.

● Some functions cannot be performed when a certain input port is selected, or
when a certain input signal is displayed.

24

Multifunctional settings

 EASY MENU

 ASPECT             4:3

+0

+0

+0
+0
+0
 3

 Go To Advance Menu...

NORMAL

NORMAL
NORMAL

0h
ENGLISH

KEYSTONE
MODE
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
WHISPER
MIRROR
RESET
FILTER TIME
LANGUAGE

EASY Menu

With the EASY MENU, items shown in the table below can
be performed.

Select an item using the cursor buttons ▲/▼ on the
projector or remote control. Then perform it referring to the
following table.

Item Description

ASPECT

KEYSTONE

MODE

BRIGHTNESS

CONTRAST

COLOR

SHRPNESS

WHISPER

TINT

Using the buttons ◄/► switches the mode for aspect ratio.
See the ASPECT item in the IMAGE menu

Using the buttons ◄/► corrects the keystone distortion.
See the item KEYSTONE of section SETUP menu. (21)

Using the buttons ◄/► switches the mode of picture type. The
modes of picture type are combinations of a mode of GAMMA and
a mode of COLOR TEMP

. Choose a suitable mode according to the

projected source.

NORMAL

CINEMA



DYNAMIC



NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT)
CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT)
DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT)

• When the combination of GAMMA and COLOR TEMP differs from
pre-assigned modes above, the display on the menu for the MODE
is “CUSTOM”. Please refer to the GAMMA (
TEMP (

•

When this function is performed, a certain extra such as a line may appear.

28) items in the PICTURE menu.



Using the buttons ◄/► adjusts the brightness.
See the item BRIGHTNESS in the PICTURE menu (27).

Using the buttons ◄/► adjusts the contrast.
See the item CONTRAST of section PICTURE menu (27).

Using the buttons ◄/► adjusts the strength of whole color.
See the COLOR item in the PICTURE menu (28).

Using the buttons ◄/► adjusts the tint.
See the TINT item in the PICTURE menu (28).

Using the buttons ◄/► adjusts the sharpness.
See the SHARPNESS item in the PICTURE menu (28).

• There may be some noise when an adjustment is made. This is
not a malfunction.

Using the buttons ◄/► turns off/on the whisper mode.
See the WHISPER item in the SETUP menu (34).

(30).

27) and COLOR



25

26

Multifunctional settings

EASY Menu (continued)

Item Description

MIRROR

RESET

FILTER TIME

LANGUAGE

Go To

Advanced Menu

Using the buttons ◄/► switches the mode for mirror status.
See the MIRROR item in the SETUP menu (34).

Performing this item resets all of the items of EASY MENU except
FILTER TIME and LANGUAGE.
A dialog is displayed for confirmation. Selecting RESET using the
button ▲ performs resetting.

Performing this item resets the filter timer which counts usage time
of the air filter.
A dialog is displayed for confirmation. Selecting RESET using the
button ▲ performs resetting.
See the FILTER TIME item in the OPTION menu (38).

Select the LANGUAGE item to toggle the menu language. Refer to
description of LANGUAGE in the SCREEN menu (35).

Select “Go To Advanced Menu” to use the
IMAGE, INPUT, SETUP, SCREEN

menu of PICTURE,

or OPTION.

Multifunctional settings

1

+0

2

+0

3

+0

4

+0

5

+0

6

+0

7

+0

8

+0

GAMMA [CUSTOM 1

]

ENTER :

 MENU [RGB]

 IMAGE

 SETUP

 PICTURE

 INPUT

 OPTION

 SCREEN

 SHARPNESS        3

BRIGHTNESS     ＋0
 CONTRAST       ＋0

COLOR           +0
 TINT            +0

 COLOR TEMP   MIDDLE

 GAMMA        DEFAULT 1

 MY MEMORY    SAVE 1

   :SELECT

 EASY MENU

 PROGRESSIVE  TURN OFF

PICTURE Menu

With the PICTURE menu, the items shown in the table
below can be performed.

Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button
on the remote control to execute the item. Then perform it
referring to the following table.

Item Description

BRIGHTNESS Using the buttons ▲/▼ adjusts the brightness. : Light  Dark

CONTRAST Using the buttons ▲/▼ adjusts the contrast. : Strong

Using the buttons ▲/▼ switches the GAMMA mode.

#1 DEFAULT

#1 CUSTOM  #2 DEFAULT





Weak

GAMMA

#3 CUSTOM

 #3 DEFAULT  #2 CUSTOM

To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM

Selecting a mode of CUSTOM and then
pressing the button ► or the ENTER button
displays a dialog to aid you in adjusting the
mode.
This function is useful when you want to
change the brightness of particular tones.

Choose an item using the buttons ◄/►, and
adjust the level using the buttons ▲/▼.

You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as
below.

No pattern  Gray scale of 9 steps
Ramp  Gray scale of 15 steps
The eight equalizing bars correspond to eight tone levels of the

test pattern except the darkest in the left end. If you want to adjust
the 2nd tone from left end on the test pattern, use the equalizing
adjustment bar “1”. The darkest tone at the left end of the test
pattern cannot be controlled with any of equalizing adjustment bar.

• When this function is performed, a certain extra such as a line
may appear.

27

28

Multifunctional settings

R

+0

G

+0

B

+0

COLOR TEMP

ENTER :

OFFSET

R

+0

G

+0

B

+0

GAIN

PICTURE Menu (continued)

Item Description

Using the buttons ▲/▼ switches the mode of color temperature.

HIGH  MIDDLE  LOW

To adjust CUSTOM

Selecting the CUSTOM and then pressing the
button ► or the ENTER button displays a dialog
to aid you in adjusting the OFFSET and/or GAIN
of the CUSTOM mode.

OFFSET adjustments change the color intensity
on the whole tones of the test pattern.

COLOR TEMP

COLOR

TINT

SHARPNESS

GAIN adjustments mainly affect color intensity
on the brighter tones of the test pattern.

Choose an item using the buttons ◄/►, and adjust the level using
the buttons ▲/▼.

You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as
below.

No pattern  Gray scale of 9 steps
Ramp  Gray scale of 15 steps

• When this function is performed, a certain extra such as a line
may appear.

Using the buttons ▲/▼ adjusts the strength of whole color.

Strong

• This item can be selected only for a video signal.
Using the buttons ▲/▼ adjusts the tint.

Green  Red

• This item can be selected only for a video signal except for
SECAM.

Using the buttons ▲/▼ adjusts the sharpness.

Strong

• There may be some noise and/or the screen may flicker for a
moment when an adjustment is made. This is not a malfunction.





Weak

Weak

CUSTOM

