Dual DMP660, DMP66 User Manual

DMP66/DMP660

MARINE

INSTALLATION/OWNER'S MANUAL

6.5" Dual Cone Marine Speakers

DMP66/DMP660 INSTALLATION

Preparation/Installation

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. Consult a qualified technician for instructions.

• Use extreme caution when drilling holes to avoid damaging fuel lines, hydraulic lines
or existing wiring.

• If additional wiring is required, we recommend that you run all wires prior to
mounting your speaker in place.

• Use the highest quality connectors for a reliable installation and to minimize signal
and power loss.

• Use caution before you drill or cut! Be careful not to cut or drill into gas tanks, fuel lines,
hydraulic lines, vacuum lines or electrical wiring.

• Avoid running wires over, near, or through sharp edged surfaces. We suggest you
also use rubber grommets to protect any wires routed through metal.

Getting Started

• Determine where the speakers will be mounted. Ensure an area large enough for
the speaker to mount evenly. Be sure the mounting location is deep enough for the
speaker to fit.

• Using an appropriate tool, cut a 5.13" diameter mounting hole.

• Use the speaker as a template to mark the locations for the mounting screws. Drill
the holes with a 3/32" bit. Route speaker wires and connect to speakers, observing
speaker polarity.

• Install speaker into opening using supplied hardware and test for correct operation.

TYPICAL MOUNTING METHOD

2

DMP66/DMP660 WARRANTY

Limited One Year Warranty

This warranty gives you specific legal rights.
You may also have other rights which vary from

state to state.

Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.

Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.

Who is covered? This warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.

What is covered? This warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.

What to do?

1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls or connections discussed in your
instruction booklet may save you a service
call.

2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.

3. Please describe your problem in writing and
include your name, a USA return shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.

4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:

• Call us toll-free at 1-866-382-5476

• E-mail us at [e-mail]

Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.

3

DMP66/DMP660 SPECIFICATIONS

Specifications

Outside Diameter

Mounting Depth

Mounting  Height

Cut-out Diameter

Frequency Response

Sensitivity

Impedance

RMS Power

Peak Power

7.05"

2.24"

.71"

5.13"

45Hz-15kHz

88dB 1W/1M

4 ohms

20 Watts @ 1kHz

60 Watts @ 1kHz

Design and specifications subject to change without notice.

Dual Electronics Corp.

Toll Free: 1-866-382-5476

www.dualav.com

©2009 Dual Electronics Corp.

NSA0809-V03