Dual DC416BT User Manual

DC416BT

Front and Rear Inputs

INSTALLATION/OWNER'S MANUAL

AM/FM/CD Receiver with Detachable Face

Front Input

DC416BT INSTALLATION

REMOV

Preparation

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. Consult a qualified technician for instructions.

• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Getting Started

• Remove trim ring from unit.

• Remove 2 transit screws located on top of the unit.

• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.

• Install mounting sleeve into opening, bending tabs to secure.

• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.

• Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).

• Test for correct operation and slide into mounting sleeve to secure.

• Snap trim ring into place.

MOUNTING SLEEVE

AL KEYS

HEAD UNIT

INSTALLATION MOUNTING KITS OR DASHBOARD

TYPICAL FRONT-LOAD DIN MOUNTING METHOD

DC416BT INSTALLATION

Wiring Diagram

Antenna

Connector

10 AMP

AGC Fuse

FUSE

When replacing the

fuse, make sure new

fuse is the correct type

and amperage. Using

an incorrect fuse could

damage the radio.

The DC416BT uses

one 10 amp ATM fuse

located beside the wiring

connector.

DC416BT OPERATION

Control Locations - Receiver

1. Release

2. Band / Go Back

3. Volume / Select

4. Power / Mute

5. USB Port

6. Eject

7. Auxiliary Input

8. Preset 6 / Folder Up / Thumbs Up

9. Preset 5 / Folder Down / Thumbs Down

5 6

1. Mode

2. Volume Up

3. Power

4. Select

5. Tune / Track Up

6. Volume Down

7. Band / Go Back

8. Preset 3 / Intro

9. Preset 2 / Random

10. Preset 6 / Folder Up / Thumbs Up

11. Mute

12. Audio / Menu

13. Preset 5 / Folder Down / Thumbs Down

14. Preset 4 / Play / Pause

15. Preset 1 / Repeat

16. Bluetooth Talk

17. Tune / Track Down

1213

10. Preset 4 / Play / Pause

11. Preset 3 / Intro

12. Preset 2 / Random

13. Preset 1 / Repeat

14. Display

15. Tune / Track Up

16. Tune / Track Down

17. Mode

18. Audio / Menu

19. Bluetooth Talk

DC416BT OPERATION

General Operation

Power On/Off

Mode

Auxiliary Input

Volume

Display

Reset

Set the Clock

12/24-hour Clock

Press or any other button (except EJECT) to turn the unit on. Press to turn the unit off.

Press MODE to select between AM/FM, CD player, auxiliary front/rear, USB and Bluetooth. Modes of operation are shown in the display.

NOTE: CD and USB modes will not appear unless a CD is inserted or USB device is connected.

The DC416BT offers a 3.5 mm port on the front panel to connect audio device, MP3 player, etc. Press MODE to select AUX mode.

Adjust volume using volume knob (00-46).

Press DISP to select between clock and different types of information, such as radio frequency, CD track/elapsed time or MP3/WMA song information.

Press RESET upon initial installation or if abnormal operation occurs. Reset button is located behind the front panel.

With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE and TUNE tarily to save the selected time.

The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00).

to adjust the minutes. Press DISP momen-

to adjust the hours

Setup Menu

Press and hold AUDIO/MENU for more than 3 seconds to access the setup menu. Press AUDIO/MENU momentarily to select between the menu functions and rotate the volume knob left/right to adjust or activate the desired function.

DC416BT OPERATION

General Operation - Setup Menu

Menu Function Options Action

Auto Station

Store

Local/Distance

Tuning

Tuner

Frequency

Spacing

Auxiliary

Input

Beep

Confirmation

Programmable

Turn On Volume

Power on

Message

Scrolling

Option

Demonstration

Mode

LED Color

Bluetooth

Auto Answer

AUTO STORE

LOCAL OFF Activates distance tuning (Tuner mode only).

LOCAL ON

FREQ USA

FREQ EURO

AUX ON Enables the front panel 3.5mm auxiliary input.

AUX OFF Disables the front panel 3.5mm auxiliary input.

BEEP OFF Disables the confirmation beep.

BEEP ON Enables the confirmation beep.

PRO-VOL #

MSG OFF Disables power on message. (example: GOOD MORNING)

MSG ON Enables power on message to be displayed.

SCROLL 15 S Programs unit to scroll information every 15 seconds (default).

SCROLL ONCE

SCROLL ON Programs unit to scroll continuously.

SCROLL OFF Programs unit to show the first 10 characters on the display.

DEMO OFF Disables the demonstration mode.

DEMO ON Enables the demonstration message.

LED AUTO

BLUE

GREEN

RED

YELLOW

PURPLE

CYAN

WHITE

LED ADJ

BT ON Enables Bluetooth functionality.

BT OFF Disables Bluetooth functionality.

ANSWER ON

ANSWER OFF

Press SELECT to seek and save 6 strong stations in the current band. (Tuner mode only)

Activates local tuning for strong station reception only (Tuner mode only).

Programs the unit to USA tuner spacing. (200kHz for FM and 10kHz for AM). (Tuner mode only)

Programs the unit to European tuner spacing. (50kHz for FM and 9kHz for AM). (Tuner mode only)

Programs unit to always turn on at a specific volume (default is OFF). Any volume level 1-30 can be selected.

Programs unit to scroll once, then show the first 10 characters on display.

Programs unit to automatically rotate through all LED colors.

Programs unit to use blue LED display.

Programs unit to use green LED display.

Programs unit to use red LED display.

Programs unit to use yellow LED display.

Programs unit to use purple LED display.

Programs unit to use cyan LED display.

Programs unit to use white LED display.

Press and rotate the volume knob to adjust each RGB color level. After adjustment, that color will appear on the LCD.

Programs unit to automatically answer every incoming phone call after 2-3 rings.

Programs unit to require the answer incoming phone calls.

button must be pressed to

DC416BT OPERATION

General Operation

Audio

Bass

Treble

Balance

Fader

Loudness

Source Volume Level

Press AUDIO/MENU momentarily to select between Bass, Treble, Balance, Fader, Subwoofer and Source Volume Level.

BASS TREBLE BALANCE FADER EQ LOUD SOURCE LEVEL

Press AUDIO/MENU until BASS appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).

Press AUDIO/MENU until TREBLE appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).

Press AUDIO/MENU until BAL appears then rotate volume knob left/right to adjust

BAL EVEN represents equal balance

Press AUDIO/MENU until FADER appears then rotate volume knob left/right to adjust (FADER FRONT 12 - FADER REAR 12). FADER EVEN represents equal fader

Press EQ, then turn the volume knob to cycle through the following equalization curves: FLAT (default), POP, JAZZ, CLASSIC, BEAT, ROCK and USER. Any manual adjustment to the Bass or Treble settings are automatically saved as USER.

Press AUDIO/MENU until LOUD appears then rotate volume knob left/right to adjust LOUD ON/OFF.

The source volume level control allows a gain adjustment for each audio source: AM, FM, CD, AUX and USB. Set the source volume level for each mode, depending on the relative volume of each audio source.

(BAL LEFT 12 - BAL RIGHT 12).

To set the source volume level, press AUDIO/MENU until SRC LEVEL appears. After one second, the current mode will appear on the display. Turn the volume knob to adjust the audio level of the current source (-3 minimum/+3 maximum).

Note: Only the current mode will be available for adjustment. To adjust another mode of operation, press MODE until the desired mode is selected, then set the source volume level for that mode.

DC416BT OPERATION

AM/FM Tuner Operation

Seek Tuning

Manual Tuning

Band

Storing and Recalling

Station Presets

Press TUNE to seek to the next strong station.

Press TUNE radio frequency up or down one step at a time. Press and hold to advance quickly.

Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands.

Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button.

or TUNE

for more than one second

momentarily to change

+ 18 hidden pages