DTS XR700 User Manual

XR700 WASH XR700 WASH

GB

User Manual Rel 1.0

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S.

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

ARC 1200

2

XR700 WASH

ARC 1200

3

XR700 WASH

ARC 1200

3

INDEX:

1- TECHNICAL FEATURES 4
2- IMPORTANT SAFETY INFORMATION 6

2.1 Fire prevention

2.2 Prevention of electric shock

2.3 Protection against ultraviolet radiation

2.4 Safety

2.5 Level of protection against the penetration of solid and liquid matter

3- MOUNTING THE LAMP 7

3.1 Lamp alignment

4- VOLTAGE AND FREQUENCY 8
5- INSTALLATION 8

5.1 Safety cable

5.2 Protection against liquids

5.3 Movement

5.4 Risk of fire

5.5 Forced ventilation

5.6 Ambient temperature

6- MAINS CONNECTION 9

6.1 Protection

7- DMX SIGNAL CONNECTION 9

7.1 DMX Addresses

7.2 Selecting the DMX address

8- DISPLAY FUNCTIONS 12
9- PAN & TILT SPEED 15
10- FANS SPEED
11- ERROR MESSAGES
12- HIDDEN MENU 16
13- OPENING THE PROJECTOR HOUSING 17
14- PERIODIC CLEANING

14.1 Lenses and reflectors

14.2 Fans and air passages

15- PERIODIC CONTROLS
16- DMX PROTOCOLS 18
17-COLOUR WHEEL 23
18- 8 MOTORS CONTROL CARD 24
19- PAN & TILT CARD 25
20-CABLES RESEND CARD
21-DISPLAY CARD
22- LAMP ON-OFF CONTROL CARD

XR700 WASH

ARC 1200

4

XR700 WASH

1- TECHNICAL FEATURES

The XR700 WASH is a brand new moving head fitted with a 700W discharge lamp, which delivers a
massive 17.000 Lux at 5 m. The XR700 WASH is fitted with a Philips MSR Gold 700/2 Fastfit lamp
(50.000 Lumens) combined with a dichroic parabolic reflector. The XR700 WASH incorporates motorized
zoom: 20°- 45°, rotating indexable beam shaper (0°-180°), 2 frost filters, 2 colour conversion filters
(3.200°K and 5.600°K), CMY colour generation + a colour wheel (6 dichroic filters + open, with linear
selection for perfect 2-colour beams), and electromagnetic or electronic ballast. The XR700 WASH also
includes a new Pan / Tilt locking system with recessed buttons. The XR700 WASH is particularly suitable
for all professional applications, both mobile (concerts, shows, tours, special events) and fixed (clubs
and other venues), requiring a light with extremely luminous output capable of illuminating objects and
large backgrounds with an endless variety of colours.

XR 700 WASH (Cod. 03.MW003.L)• Electromagnetic ballast 230V 50/60 Hz• Black colour
XR 700 WASH (Cod. 03.MW003. EB.L)• Electronic ballast 90-260V 50/60 Hz• Black colour

All models are also available in white colour

Lamp

Lamp: Philips MSR Gold 700/2 Fastfit . Automatic switching on of lamp in case of accidental switching off
Lamp on/off via DMX; reset via DMX.

Optical group

17.000 Lux at 5 m (20°). Fresnel lens Ø 200 mm. Borosilicate dichroic parabolic reflector

Zoom

Motorized zoom (20°- 45°)

Dimmer / shutter / strobo

Linear dimmer, Shutter, Strobe from 0,85 flash/sec to 10 flash/sec
Power saving mode (the lamp dims to 50% six seconds after shutter closure)

Colours

CMY color generation system with 3 palettes + colour wheel (6 colours + open) with linear selection for
perfect 2-colour beams. Color change with blackout sync

Effects

Rotating and indexable beam shaper (0°-180°)

Pan / Tilt

Pan 540° (3,9 sec.). Tilt 270° (2,6 sec.). 16-bit resolution

3-Speed function (3 selectable pan/tilt speeds); extremely smooth and precise movements even at the
highest speeds. Pan / Tilt locking system with recessed buttons. Automatic Pan/Tilt repositioning in case
of knocks

16 DMX channels

Internal operating system updatable via DMX

Connections

4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik

Power supply

Electronic ballast: 90 - 260 V (50/60 Hz); power consumption: 820 W
Electromagnetic ballast: 230 V (50/60 Hz) power consumption: 820 W

Standard accessories

2 x “C” GQuick clamps with “fastlock” connection 1/4 turn

Thermal

Operating ambient temperature: -10° / 40°

Weight

23 Kg (electronic ballast)
29 Kg (magnetic ballast)

1- TECHNICAL FEATURES

ACCESSORIES

• MSR Gold 700/2 Fastfit lamp (cod. 0505S018)

• Double Professional Flight case; compartment for lamps and accessories, swivel wheels, cover with
hinges with-stay, dishes on cover for piling, 8 handles (2 each side)
(cod. 0521C032)

• Raincover for XR base (top) (cod. 03.MA001)

• Raincover for XR base (bottom) (cod. 03.MA002)

• Embedding flange for XR (visible display) (cod. 03.MA005)

• Embedding flange for XR (no visible display) (cod. 03.MA006)

• Wireless DMX receiver card (cod. 03.LA.012)

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod.0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

Packaging Dimensions (AxLxP)

550 x 440 x 800mm

Weight

34 Kg (with electronic ballast);
39 Kg (with magnetic ballast).

ARC 1200

5

XR700 WASH

415 mm

408 mm

470 mm

430 mm

650 mm

0 m60 m

270 °

6

2- IMPORTANT SAFETY INFORMATION

2.1 Fire prevention:

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if
there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

2.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head, including lamp replacement.

-The level of technology present in the XR700 requires the assistance of specialised personnel for all
servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

2.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

2.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

2.5 Level of protection against the penetration of solid and liquid matter:

-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid matter is IP 20.

XR700 WASH uses a Philips MSR Gold 700/2 Fastfit lamp.

XR700 WASH

3- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .

2) Insert the lamp (photo2).

3)Rotate the lamp 1/4 turn clockwise (photo 3 and 4).
The lamp used on XR700 is made in quartz glass and should be handled with care. Always follow the
instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided
in the lamp's packaging. The lamp socket is not symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat
the procedure.

4) Replace the metal cover and tighten the screws A,B,C, which were previously removed.

3.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic
filters and other components inside the unit.

Alignment is carried out using the 3 adjusters X, Y and Z.
During this operation you must have a uniform luminosity all around the projected area.

Philips MSR Gold 700/2 Fastfit
Power 700W
Luminous flux 50,000 lm
Colour temperature 7.500°K
Lampbase PGJX50
Rated life 750 hours

PGJX50

7

Photo 2Photo 1 Photo 4Photo 3

Photo 5

XR700 WASH

4- VOLTAGE AND FREQUENCY

The XR700 with electronic ballast operates at 90-260 VOLT 50 or 60 Hz.
The XR700 with electromagnetic ballast operates at 230 VOLT 50 or 60 Hz.

5- INSTALLATION

XR700 may be either floor or ceiling mounted.
For floor mounting installations, the XR700 is supplied with four rubber mounting feet on the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake whilst the XR700 is moving.

Four quarter turn fast locks placed on the base of the units, allow by using the two fast lock C clamps

provided in the box, to fix the unit in any position.
.

5.1- Safety cable

We recommend the use of a safety cable or chain connected to the XR700 and to the suspension truss
in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron
cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the
picture below.

5.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.

8

A

XR700 WASH

5.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any
obstructions in the path of the projector's movement.

5.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 2 MT.

5.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the
base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the
projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

5.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.

6- MAINS CONNECTION

XR700 with electronic ballast operates at 90-260 VOLT 50-60 Hz.
XR700 with electromagnet ballast operates at 230 VOLT 50-60 Hz
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is capable of supporting 6,3 amps at 208-230V,
or16 amps at 100-120 V
Strict adherence to regulatory norms is strongly recommended.

6.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR700.
A good earth connection is essential for the correct operation of the projector.

7- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a
CANNON XLR 5 or 3 pins connector.

9

540°

270°

XR700 WASH

Electronic ballast
90-260V 50 / 60Hz

Electromagnetic ballast
230V 50 / 60Hz

Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it
to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
In this way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed,we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

5

3

4 2

1

1=GND
2=DATA­3=DATA+

CONTROLLER
S TA ND AR D
D M X 5 1 2

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

10

XR700 WASH

7.1-DMX Addresses

XR700 Wash have 16 DMX channels.

Set the following addresses on the mixer:

Projector 1 A001
Projector 2 A017 If you want to select the next projector, just add “16”

Projector 3 A033
….. A….
projector 6 A081

7.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now setted to the new DMX address.

TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.

11

XR700 WASH

DMX IN

DMX OUT

DISPLAY

12

MENU

ENTER

DOWN

UP

DISPLAY FUNCTIONS

The XR700 display panel shows all the available functions . Using these functions, it is possible to

change some of the parameters and add some functions. Changing the D.T.S. setting can vary the

functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully
follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Up-DownMENU ENTERUp-Down

PAN MOVEMENT INVERSION
To reverse Pan movement from left
to right and vice versa

Up-Down

Counterclockwise

Clockwise

Up-DownMENU ENTERUp-Down

TILT MOVEMENT INVERSION
To reverse Tilt movement from
bottom upwards and vice versa

Up-Down

Counterclockwise

Clockwise

Up-DownMENU ENTER

DMX MODE
To select DMX mode :
Mode 1 or Mode 2

16 CHANNELS

(Pan & Tilt 16 bit)

16 CHANNELS

(Pan & Tilt 16 bit)

Up-Down

Up-Down

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

Up-Down

MENU

ENTERUp-Down

REVERSE DISPLAY
Reverses display's reading depending on
the mounting position
(On the ground or suspended).

Up-Down

Floor

position

Suspension

position

Up-DownENTER

Up-DownENTER

DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.

Display OFF

Display

always ON

ENTER

ENTER

ENTER

ENTER

XR700 WASH

DEFAULT

SAME FIXTURE AS

XR 7 WASH

MAINS

FUSE

16 A

DMX IN

DMX OUT

Electronic ballast
90-260V 50 / 60Hz

Electromagnetic ballast
230V 50 / 60Hz

8- DISPLAY FUNCTIONS

13

XR700 WASH

8- DISPLAY FUNCTIONS

MENU ENTER

TEST MODE
Full test and single function test.

Up-Down

Up-Down

MENU

ENTER

DEFAULT
To restore default setting

ENTER

Up-Down

MENU ENTER

Fan control
To control the fan speed .

Up-Down

ENTER

Up-Down

(DEFAULT : 5 )

MENU ENTER

Up-Down

ENTER

ENTER

Up-Down

(DEFAULT : 2 )

SPEED control
Pan Tilt Speed control.

PAN

TILT

DIMMER

SHUTTER

MAGENTA

COLOR

CYAN

YELLOW

EFFECTS

ZOOM

ENTER

MENU

Up-Down

ENTER

Pcb 8 motors. Pcb PAN&TILT

ALL

SOFTWARE
Software version

MENU

Up-Down

RESET
Al motors reset

RESET ENABLED VIA DMX

RESET DISABLED VIA DMX

TOTAL RESET

ENTER

ENTER

ENTER

ENTER

Up-Down

LAMP
Lamp always ON-always OFF
Or lamp ON-OFF selectable via DMX

ENTER

FORCED ON

ENTER

FORCED OFF

ENTER

ON / OFF VIA DMX (default)

MENU

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ADJUST
To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and FOCUS

ENTER

STR
Lamp strikes counter

ENTER

Up-Down

14

XR700 WASH

8- DISPLAY FUNCTIONS

MENU

Up-Down

ENTER

RESERVED
Pan lock-Tilt lock
Pan free-Tilt free

Up-Down

ENTER

.

Up-Down

ENTER

Up-Down

ENTER

ENTER

Up-Down

ENTER

ENTER

Up-Down

ENTER

Up-Down

.

ENTER

ENTER

ENTER

Up-Down

ENTER

ENTER

ENTER

Up-Down

.

.

ENTER

PAN LOCK
LOCK THE PAN TO THE DESIRED VALUE

TILT LOCK
LOCK THE TILT TO THE DESIRED VALUE

PAN FREE
REMOVE POWER TO PAN MOTOR

TILT FREE
REMOVE POWER TO TILT MOTOR

MENU ENTER

TIMER
lamp life TIME (reset possible)
and total UNIT LIFE TIME (reset not possible)

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

ENTER

BLACKOUT DISABLED

ENTER

BLACKOUT ENABLED (default)

MENU

Up-Down

ENTER

Up-Down

SILENT
Silent operating mode during PAN&TILT movement.
By activating this function, PAN and TILT motors will
be driven with less power (during acceleration and
deceleration) in order to reduce the noise during
PAN&TILT rotation

ENTER

SILENT MODE DISABLED

ENTER

SILENT MODE ENABLED (default)

MENU

Up-Down

ENTER

Up-Down

BLACKOUT
CMY filters blades inserted at 100% if the dimmer
remain closed for more than 5 seconds.
By activating this function, it will be possible to
reduce substantially any visible light reflection
coming out from the front lens when dimmer is
closed.

15

XR700 WASH

9- PAN & TILT SPEED (SPEE) (default: 2)

10- FAN SPEED (FANS)( default: 5)

You can set the PAN and TILT motors at high speed on your XR700.

Press menu until you see SPEE.
Press ENTER and select a speed with UP-DOWN (there are 3 speeds). Confirm by pressing ENTER.
When you use speed 3 (the highest) PAN and TILT speed is very high and your projector may loose its
path. In this case, the encoder corrects the position.

Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be
less than 35° C.

11- ERROR MESSAGES:

ERROR ENCODER PAN

ERROR ENCODER TILT

ERROR DMX ADDRESS

ERROR LOADING

ERROR COLOUR SENSOR

ERROR COLOUR SENSOR

EPROM DATA

CIRCUIT/ZOOM 1

CIRCUIT/ZOOM 2

ERROR POSITIONING

ERROR ALIGNMENT

ERROR INTERNAL

ERROR INPUT

ERROR POSITIONING
OF COLOUR WHEEL

ERROR POSITIONING

OF BEAM SHAPE EFFECTS

OF ZOOM

SENSORS OF ZOOM LENS

IN AUTO MODE

COMMUNICATION

ERROR SYNCHRONIZED
FREQUENCY MEASURE
(SYNCHRONISM FOR LAMP ON)

16

XR700 WASH

16

12- HIDDEN MENU

For technical personnel only.

To operate this menu:

-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)

- Reset the XR700 (reset from the MENU, not from the DMX controller!).

- While reset is running, press the MENU and ENTER keys at the same time.

Electronic calibration of the motors.

Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must
repeat all previous calibrations)

Exit from hidden menu.

Up-DownENTERUp-Down

ES.

ENTER

Up-DownENTER

Up-Down

ES.

ENTER

Up-DownENTERUp-Down

ES.

ENTER

Up-DownENTERUp-Down

ES.

ENTER

Up-DownENTERUp-Down

ES.

ENTER

Up-DownENTERUp-Down

ES.

ENTER

Up-DownENTER

ES.

ENTER

Up-DownENTER

ES.

ENTER

Up-Down

Up-Down

ENTER

Up-DownENTERUp-Down

ES.

ENTER

PAN ALIGNMENT
To align pan movement

TILT ALIGNMENT
To align tilt movement

SHUTTER ALIGNMENT
To align shutter

EFFECT ALIGNMENT
Effect alignement

ZOOM 1 ALIGNMENT
To align zoom1

colour WHEEL ALIGNMENT
To align colour wheel

CYAN ALIGNMENT
To align cyan colour

MAGENTA ALIGNMENT
To align magenta colour

YELLOW ALIGNMENT
To align yellow colour

Up-DownENTERUp-Down

ES.

ENTER

ZOOM 2 ALIGNMENT
To align zoom 2

17

13- OPENING THE PROJECTOR HOUSING

It is possible to inspect the inside of the projector by removing the cover as indicated below.

ATTENTION

REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.

1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) .

2) Once unscrewed, simply lift the covers to access the internal components (photo 2).

Photo 1

XR700 WASH

Photo 2

14- PERIODIC CLEANING

14.1- Lenses and reflectors

Even a fine layer of dust can substantially reduce the luminous output . Regularly clean all lenses
and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.

14.2- Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning
will depend of course, on the conditions in which the projector is operating. Suitable instruments
for performing this type of maintenance are a brush and a common vacuum cleaner or an air
compressor. If necessary, clean the fans and air passages more frequently.

15- PERIODIC CONTROLS

Lamp

The lamp should be replaced if there is any visible damage or deformation due to heat. This will

help to avoid the danger of the lamp explosion.

Mechanical parts

Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them
if necessary. Periodically check the lubrication of all components, particularly the parts subject to
high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.
distributor. Check the tension of the belts and adjust it if necessary.

Electrical components

Check all electrical components for correct earthing and proper connection of all connectors;
refasten them if necessary.

Fuse replacement

Locate the fuse, which protects the lamp and electronics, in the base of the XR700.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.

18

16 CHANNEL MODE ( 16bit)

1 PAN ms b ( 5 4 0°)
2
3

TILT msb(320°)

4 TILT l s b
5
6 D IM MER
7 SHU T T ER
8 C OL OUR
9 C YAN
10 MAGENTA
11 YEL L O W
12 SPEED CMY / DIMMER
13 MACRO CMY / COLOUR
14 E FF ECTS
15 ZOOM
16 RESET

DMX CHANNEL

1

Parameter: PAN msb 540°

DMX CHANNEL

2

Parameter: PAN lsb

DMX CHANNEL

3

Parameter: TILT msb 319°

DMX CHANNEL

4

Parameter: TILT lsb

DMX CHANNEL

5

Parameter: MOVEMENT SPEED

DMX range

Value

Mid point

DMX value

Move
range

(degrees)

Mode Option Function

0-10

Standard

11-25

Fast movement

26-127

Vector mode from fast to slow

128-247

Variable time reaction to

DMX signal ( fast to slow)

248-255

Slow reaction time to DMX

signal

DMX CHANNEL

6

Parameter: DIMMER

DMX range

Value

Mid point

DMX value

Move
range

(degrees)

Mode Option Function

0-8

Black-out

9-255

Proportional dimmer

PAN lsb

MOVEMENT SPEED

XR700 WASH

16- DMX PROTOCOL

-

-

ARC 1200

19

DMX CHANNEL

7

Parameter: SHUTTER

DMX range

Value

Mid point

DMX value

Move
range

(degrees)

Mode Option Function

0-9

Black-out

10-23

Strobe random speed

24-37

Strobe speed 1 min.

38-51

Strobe speed 2

52-65

Strobe speed 3

66-79

Strobe speed 4

80-93

Strobe speed 5

94-107

Strobe speed 6 max.

108-121

Flash open speed 1 min.

122-135

Flash open speed 2

136-149

Flash open speed 3

150-163

Flash open speed 4 max.

164-177

Flash closed speed 1 min.

178-191

Flash closed speed 2

192-205

Flash closed speed 3

206-219

Flash closed speed 4 max.

220-227

Colours / Macros in black-out

228-233

Pan / Tilt in black-out

234-255

Open

DMX CHANNEL

8

Parameter:

COLOUR

DMX range

Value

Mid point

DMX value

Move
range

(degrees)

Mode Option Function

0-12

White

13-25

Colour 1 (3200° K)

26-38

Colour 2 (5600°K)

39-51

Colour 3

52-64

BiColour 3/4

65-77

Colour 4

78-90

BiColour 4/5

91-103

Colour 5

104-116

BiColour 5/6

117-129

Colour 6

130-142

BiColour 6/7

143-155

Colour 7

156-168

Bicolour 7/8

169-181

Colour 8

182-197

Bicolour 8/white

198-200

Right rotation speed 1 max.

201-203

Right rotation speed 2

204-206

Right rotation speed 3

207-209

Right rotation speed 4

XR700 WASH

-

ARC 1200

21

210-212

Right rotation speed 5

213-215

Right rotation speed 6

216-218

Right rotation speed 7

219-221

Right rotation speed 8

222-224

Right rotation speed 9 min

225-228

Stop

229-231

Left rotation speed 1 min.

232-234

Left rotation speed 2

235-237

Left rotation speed 3

238-240

Left rotation speed 4

241-243

Left rotation speed 5

244-246

Left rotation speed 6

247-249

Left rotation speed 7

250-252

Left rotation speed 8

253-255

Left rotation speed 9 max.

DMX CHANNEL

9

Parameter: CYAN

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-255

Proportional colour

DMX CHANNEL

10

Parameter: MAGENTA

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-255

Proportional colour

DMX CHANNEL

11

Parameter:

YELLOW

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-255

Proportional colour

DMX CHANNEL

12

Parameter: SPEED CMY / DIMMER

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-7

No Function

8-255

Variable speed from max to min

XR700 WASH

0

-

ARC 1200

21

XR700 WASH

DMX CHANNEL

13

Parameter: MACRO CMY / COLOUR

DMX range

Value

Mid point

DMX value

Move
range

(degrees)

Mode Option Function

0-9
10-14
15-19
20-24
25-29
30-34
35-39
40-44
45-49
50-54
55-59
60-64
65-69
70-74
75-79

85-89
90-94

95-99
100-104
105-109
110-114

80-84

115-121
122-128
129-135

136-142
143-149
150-156
157-163
164-170
171-177
178-184
185-191
192-198
199-205

206-212
213-219
220-226
227-233
234-240
241-247
247-255

No Function
Macro 1
Macro 2

Macro 3
Macro
Macro
Macro

Macro
Macro
Macro
Macro
Macro
Macro

Macro 4
Macro 5
Macro 6

Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12

Macro

Macro

Macro

Macro

Macro

Macro

Macro

Macro

Macro

Macro 13

Macro 14

Macro 15

Macro 16

Macro 17

Macro 18

Macro 19

Macro 20

Macro

Macros rainbow wait =
Macros rainbow wait =

Macros rainbow wait = 0
Macros rainbow wait = 2

Macros rainbow wait = 3
Macros rainbow wait = 4
Macros rainbow wait =
Macros rainbow wait =

Macros rainbow wait = 5
Macros rainbow wait = 6

Macros rainbow wait = 7
Macros rainbow wait = 8
Macros rainbow wait = 9
Macros rainbow wait = 10

Full colours rainbow wait = 0
Full colours rainbow wait = 2
Full colours rainbow wait = 3
Full colours rainbow wait = 4

Full colours rainbow wait = 5
Full colours rainbow wait = 6

Full colours rainbow wait = 7
Full colours rainbow wait = 8
Full colours rainbow wait = 9

Full colours rainbow wait = 10

21

-

ARC 1200

22

DMX CHANNEL

14

Parameter: EFFECTS

DMX range

Value

Mid point

DMX value

Move
range

(degrees)

Mode Option Function

0-19

No effect

20-39

Frost

40-255

Beam Shape

DMX CHANNEL

15

Parameter: ZOOM

DMX range

Value

Mid point

DMX value

Move
range

(degrees)

Mode Option Function

0-225

Proportional

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-29

No effect

30-85

Lamp OFF (active after 3

seconds)

86 - 170

Internal motor Reset

171-235

Total Reset

236-255

Lamp ON (active after 3

seconds)

DMX CHANNEL

16

Parameter: LAMP / RESET

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-9
10-60
61-129

130-179
180-200

201-239
240-255

No Effect

Lamp OFF (Active after 3 seconds)

No Effect

Internal Motors Reset

Total Reset

Lamp ON (Active after 3 seconds)

No Effect

5
30
95

154

190
220

247

XR700 WASH

MODE 1 (DEFAULT)

MODE 2 (SAME AS XR 7 WASH)

0507C042.D01
GREEN WB5055

0507C051.D01
ORANGE LW590

0507C041.D01
DARK BLUE SW490

COL6COL5

COL4

COL3COL2

COL7

COL8

0507C047.D01
RED LW 640

-

ARC 1200

23

1

2

3

4

5

6

7

8

XR700 WASH

0507K003
CONV. FILTER CTB
DL542

0507K004
CONV.FILTER CTO
TC3256

0507C046.D01
WOOD SW 460

0507C053.D01
AMBER LW 550

COL1

17- COLOUR WHEEL

24

XR700 WASH

Fans

+

-

GND
ORANGE
BROWN
VCC

30 VDC

J1 Internal DATA
Communication
Connector
From J8 Pan & Tilt
card

Fans

J7 Magnetic Sensors
Connector

Line 1 Brown:
Line 2 Orange:

Zoom motor1

(BLACK)

Zoom motor2

(DARK GREEN)

Strobe

Colour wheel

(PINK)

Magenta

(LIGHT BLUE)

Cyan

(GOLD)

18- 8 MOTORS CONTROL CARD

Yellow

(BLUE)

(YELLOW)

Effects

(GREY)

8 MOTORS CONTROL CARD

ARC 1200

25

XR700 WASH

19-PAN & TILT CARD

DATA 1

DATA 2

(VIOLET)

(LIGHT GREEN)

MOTOR TILT

(BROWN)

ENCODER TILT

(ORANGE)

FROM J12
PAN&TILT

CARD

21-DISPLAY CARD

BLACK RED

BLACK BLACK

20-CABLES RESEND CARD

22-LAMP ON-OFF CONTROL CARD

PAN

(WHITE)

TILT

(BROWN)

GND

(BLACK)

30 VDC

(RED)

FAN

(WHITE)

ENCODER TILT

(ORANGE)

ENCODER PAN

(RED)

DMX INPUT

(WHITE)

TO J1

8 MOTORS CARD

(VIOLET)

TO J2

LAMP

ON-OFF

CARD

TO J1

DISPLAY CARD

(WHITE)

J2

J3

J4

FROM J16
PAN&TILT
CARD

TO J9
ELECTRONIC
BALLAST

ARC 1200

26

XR700 WASH

NOTES

ARC 1200

27

XR700 WASH

NOTES

The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from DTS. DTS reserves the right to make any aesthetic, functional or design modifications to
any of its products without prior notice. DTS assumes no responsibility for the use or application
of the products or circuits described herein.

MADE IN ITALY

D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy

Tel. [phone] Fax [phone] [e-mail] www.dts-lighting.it