DTS XR 5 WASH User Manual

XR 5 WASH XR 5 WASH

User Manual Rel 1.1

GB

2

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S.

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione

dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

XR 5 WASH

ARC 1200

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

3

XR 5 WASH

ARC 1200

INDEX:

1- TECHNICAL FEATURES 4
2- IMPORTANT SAFETY INFORMATION 5

2.1 Fire prevention

2.2 Prevention of electric shock

2.3 Protection against ultraviolet radiation

2.4 Safety

2.5 Level of protection against the penetration of solid and liquid matter

3- MOUNTING THE LAMP 6

3.1 Lamp alignment

4- VOLTAGE AND FREQUENCY 7
5- INSTALLATION 7

5.1 Safety cable

5.2 Protection against liquids

5.3 Movement

5.4 Risk of fire

5.5 Forced ventilation

5.6 Ambient temperature

6- MAINS CONNECTION 8

6.1 Protection

7- DMX SIGNAL CONNECTION 9

7.1 DMX Addresses

7.2 Selecting the DMX address

8- DISPLAY FUNCTIONS 11
9- PAN & TILT SPEED 14
10- FANS SPEED
11- ERROR MESSAGES
12- HIDDEN MENU 15
13- OPENING THE PROJECTOR HOUSING 16
14- PERIODIC CLEANING

14.1 Lenses and reflectors

14.2 Fans and air passages

15- PERIODIC CONTROLS
16- DMX PROTOCOLS 17
17-COLOUR WHEEL 22

4

XR 5 WASH

ARC 1200

1- TECHNICAL FEATURES

The XR 5 Wash is fitted with a Philips MSD 250/2 discharge lamp
(GY9,5 lampholder base), with a colour temperature of 8500 °K and a luminous flux of
18,000 Lumens.
Average lifespam is 2000 hours, with replacement recommended before 2200 hours
Other recommended lamps: Osram HSD 250/2, GE CSD 250/2.
The unit incorporates:

Motorized zoom (13°-23°), rotating and indexable beam shaper (0°-170°), frost filter, 2
colour conversion filters (3.200°K and 5.600°K), CMY colour generation + a colour wheel (6
dichroic filters + open, with linear selection, and electronic or electromagnetic ballast.

Optical group
Fresnel lens Ø 150 mm (Borosilicate dichroic parabolic reflector)
Zoom

Motorized zoom (13°-23°)

Dimmer / shutter / strobo
Linear dimmer - Shutter - Strobe from 0,85 flash/sec to 10 flash/sec
Colours

CMY color generation system with 3 palettes for gradual and linear insertion +
colour wheel (6 colours + open). Color change with blackout sync

Effects

Rotating and indexable beam shaper (0°-170°)

Colour conversion filters

3.200°K and 5.600°K

Pan / Tilt
Pan 540° (3,9 sec.) Tilt 270° (2,6 sec.) 16-bit resolution
16 DMX channels
Connections
4 XLR connectors (In and Out) with 3 and 5 pins.

Power supply

Electromagnetic ballast: 230 V (50/60 Hz) standard. On request 110 V 50/60 Hz.
Power consumption 350 W
Remote Lamp on/off via DMX

Operating ambient temperature -10° / 40°
Weight

m6 m

20 Kg

3

3

4

23 mm

Packing Dimensions
(HxWxL)

550 x 440 x 880 mm

Weight

27 Kg

mm
0
4
5

4

027 °

1

5

mm

m
m
5

5 0

408 mm

5

XR 5 WASH

ARC 1200

2- IMPORTANT SAFETY INFORMATION

2.1 Fire prevention:

XR5 can fit a Philips MSD250/2 or a Osram HSD250/2 or a GE CSD250/2.

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if
there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

2.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head, including lamp replacement.

-The level of technology present in the Xr5 requires the assistance of specialised personnel for all
servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

2.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

2.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

2.5 Level of protection against the penetration of solid and liquid matter:

-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid matter is IP 20.

6

XR 5 WASH

ARC 1200

3- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

Philips MSD250/2
Power 250W
Luminous flux 18.000 lm
Colour temperature 8.500°K
Lampbase GY9,5
Rated life 3,000 hours

1) Using a screwdriver, remove the 3 screws X,Y, Z, (photo 1) which fix the lamp holder.

Photo 2Photo 1 Photo 3

2) Remove the lamp holder assembly and insert the lamp (photo 2).
The lamp used on XR 5 is made in quartz glass and should be handled with care. Always follow the
instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided
in the lamp's packaging. The GY9,5 lamp socket is not symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat
the procedure.

3) Replace the lamp assembly and tighten the screws X,Y,Z, which were previously removed (photo3).

3.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic
filters and other components inside the unit.

Photo 5

Alignment is carried out using the 3 adjusters A, B and C.
During this operation you must have a uniform luminosity all around the projected area.

7

XR 5 WASH

ARC 1200

4- VOLTAGE AND FREQUENCY

The XR5 with electromagnetic ballast can operate at 230 VOLT 50-60 Hz (110 VOLT 50-60 Hz on
request)

5- INSTALLATION

XR5 may be either floor or ceiling mounted.
For floor mounting installations, the XR5 is supplied with four rubber mounting feet on the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake whilst the XR5 is moving.
Four quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps
provided in the box, to fix the unit in any position.
.

5.1- Safety cable

We recommend the use of a safety cable or chain connected to the Xr5 and to the suspension truss in
order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron
cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the
picture below.

A

5.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.

8

XR 5 WASH

ARC 1200

5.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any
obstructions in the path of the projector's movement.

270°

540°

5.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 2 MT.

5.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the
base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the
projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

5.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.

6- MAINS CONNECTION

XR5 with electromagnetic ballast operate at 230 VOLT 50-60 Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is capable of supporting 3,15 amps at 230V,
Strict adherence to regulatory norms is strongly recommended.

Electromagnetic ballast

6.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR 5.
A good earth connection is essential for the correct operation of the projector.

230V 50 / 60Hz

7- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a
CANNON XLR 5 or 3 pins connector.

9

XR 5 WASH

ARC 1200

Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it
to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
In this way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

CONTROLLER
S TA N DA R D
DM X 5 1 2

5

1

1=GND
2=DATA­3=DATA+

4 2

3

For Installations where long distance DMX cable connections are needed,we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

5

4

1

2

3

OUT

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

PIN 3

120 ohm

PIN 2

10

XR 5 WASH

ARC 1200

7.1-DMX Addresses

XR 5 Wash have 16 DMX channels.

Set the following addresses on the mixer:

Projector 1 A001
Projector 2 A017 If you want to select the next projector, just add “16”

Projector 3 A033
….. A….
projector 6 A081

7.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now setted to the new DMX address.

TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.

8- DISPLAY FUNCTIONS

11

XR 5 WASH

ARC 1200

DISPLAY

DMX IN

DMX OUT

MAINS

Electromagnetic ballast

230V 50 / 60Hz

FUSE
3,15 A

MENU

ENTER

UP

DOWN

DISPLAY FUNCTIONS

The XR5 display panel shows all the available functions . Using these functions, it is possible to
change some of the parameters and add some functions. Changing the DTS setting can vary the
functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow
the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.

PAN MOVEMENT INVERSION
To reverse Pan movement from left
to right and vice versa

TILT MOVEMENT INVERSION
To reverse Tilt movement from
bottom upwards and vice versa

MENU

REVERSE DISPLAY
Reverses display's reading depending on
the mounting position
(On the ground or suspended).

DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.

ENTERUp-Down

Up-DownMENU ENTERUp-Down

Up-Down

Up-DownMENU ENTERUp-Down

Up-Down

Up-Down

Up-Down

Clockwise

Counterclockwise

Clockwise

Counterclockwise

Up-DownENTER

Up-DownENTER

ENTER

ENTER

ENTER

ENTER

Floor

position

Suspension

position

Display OFF

Display

always ON

ENTER

ENTER

ENTER

ENTER

Up-Down

DMX MODE
To select DMX mode :
Mode 1 or Mode 2

Up-DownMENU ENTER

Up-Down

DEFAULT

SAME FIXTURE AS

XR250 WASH

16 CHANNELS

(Pan & Tilt 16 bit)

16 CHANNELS

(Pan & Tilt 16 bit)

ENTER

ENTER

8- DISPLAY FUNCTIONS

12

XR 5 WASH

ARC 1200

Up-Down

MENU ENTER

TEST MODE
Full test and single function test.

MENU

Up-Down

ENTER

RESET
Al motors reset

MENU

Up-Down

ENTER

DEFAULT
To restore default setting

Up-Down

Up-Down

ALL

PAN

TILT

DIMMER

SHUTTER

COLOR

CYAN

MAGENTA

YELLOW

EFFECTS

ZOOM

RESET ENABLED VIA DMX

RESET DISABLED VIA DMX

TOTAL RESET

ENTER

ENTER

ENTER

ENTER

MENU

Up-Down

ENTER

SOFTWARE
Software version

MENU ENTER

Up-Down

Fan control
To control the fan speed .

Up-Down

MENU ENTER

SPEED control
Pan Tilt Speed control.

Pcb 8 motors. Pcb PAN&TILT

Up-Down

Up-Down

ENTER

ENTER

ENTER

ENTER

(DEFAULT : 12 )

(DEFAULT : 4 )

8- DISPLAY FUNCTIONS

13

XR 5 WASH

ARC 1200

Up-Down

MENU

ENTER

LAMP
Lamp always ON-always OFF
Or lamp ON-OFF selectable via DMX

ADJUST
To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and FOCUS

ACC
Lamp strikes counter

MENU

Up-Down

ENTER

RESERVED
Pan lock-Tilt lock
Pan free-Tilt free

PAN LOCK
LOCK THE PAN TO THE DESIRED VALUE

Up-Down

ENTER

ENTER

ENTER

ENTER

.

ENTER

ON / OFF VIA DMX (default)

FORCED ON

FORCED OFF

Up-Down

ENTER

Up-Down

Up-Down

ENTER

ENTER

ENTER

Up-Down

Up-Down

TILT LOCK
LOCK THE TILT TO THE DESIRED VALUE

PAN FREE
REMOVE POWER TO PAN MOTOR

TILT FREE
REMOVE POWER TO TILT MOTOR

MENU ENTER

Up-Down

TIMER
lamp life TIME (reset possible)
and total UNIT LIFE TIME (reset not possible)

Up-Down

Up-Down

Up-Down

Up-Down

ENTER

Up-Down

.

.

.

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

Up-Down

Up-Down

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

Up-Down

14

XR 5 WASH

ARC 1200

9- PAN & TILT SPEED (SPEE) (default: 4)

You can set the PAN and TILT motors at high speed on your Xr5.
Press menu until you see SPEE.
Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER.
When you use speed 4 (the highest) PAN and TILT speed is very high and your projector may loose its
path. In this case, the encoder corrects the position.

10- FAN SPEED (FANS)( default: 12)

Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be
less than 35° C.

11- ERROR MESSAGES:

ERROR POSITIONING
OF COLOUR WHEEL

ERROR POSITIONING

OF BEAM SHAPE EFFECTS

ERROR POSITIONING
OF ZOOM

ERROR ALIGNMENT
SENSORS OF ZOOM LENS

ERROR INPUT
IN AUTO MODE

ERROR INTERNAL
COMMUNICATION

ERROR SYNCHRONIZED
FREQUENCY MEASURE
(SYNCHRONISM FOR LAMP ON)

ERROR ENCODER PAN

ERROR ENCODER TILT

ERROR DMX ADDRESS

ERROR LOADING
EPROM DATA

ERROR COLOUR SENSOR
CIRCUIT/ZOOM 1

ERROR COLOUR SENSOR
CIRCUIT/ZOOM 2

15

XR 5 WASH

ARC 1200

12- HIDDEN MENU

For technical personnel only.

To operate this menu:

-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)

- Reset the Xr5 (reset from the MENU, not from the DMX controller!).

- While reset is running, press the MENU and ENTER keys at the same time.

Electronic calibration of the motors.

Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must

repeat all previous calibrations)

Exit from hidden menu.

16

ENTER

Up-Down

PAN ALIGNMENT
To align pan movement

Up-Down

TILT ALIGNMENT
To align tilt movement

SHUTTER ALIGNMENT
To align shutter

Up-Down

colour WHEEL ALIGNMENT
To align colour wheel

EFFECT ALIGNMENT
Effect alignement

ZOOM 1 ALIGNMENT
To align zoom1

Up-DownENTER

Up-DownENTER

Up-DownENTERUp-Down

Up-DownENTER

Up-DownENTERUp-Down

Up-DownENTERUp-Down

ES.

ENTER

ES.

ENTER

ES.

ENTER

ES.

ENTER

ES.

ENTER

ES.

ENTER

ZOOM 2 ALIGNMENT
To align zoom 2

CYAN ALIGNMENT
To align cyan colour

MAGENTA ALIGNMENT
To align magenta colour

YELLOW ALIGNMENT
To align yellow colour

Up-DownENTERUp-Down

Up-DownENTERUp-Down

Up-DownENTERUp-Down

Up-DownENTERUp-Down

ES.

ENTER

ES.

ENTER

ES.

ENTER

ES.

ENTER

16

XR 5 WASH

ARC 1200

13- OPENING THE PROJECTOR HOUSING

It is possible to inspect the inside of the projector by removing the cover as indicated below.

ATTENTION

REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.

1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) .

2) Once unscrewed, simply lift the covers to access the internal components (photo 2).

14- PERIODIC CLEANING

Photo 1

Photo 2

14.1- Lenses and reflectors

Even a fine layer of dust can substantially reduce the luminous output . Regularly clean all lenses
and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.

14.2- Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning
will depend of course, on the conditions in which the projector is operating. Suitable instruments
for performing this type of maintenance are a brush and a common vacuum cleaner or an air
compressor. If necessary, clean the fans and air passages more frequently.

15- PERIODIC CONTROLS

Lamp

The lamp should be replaced if there is any visible damage or deformation due to heat. This will
help to avoid the danger of the lamp exploding.

Mechanical parts

Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them
if necessary. Periodically check the lubrication of all components, particularly the parts subject to
high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.
distributor. Check the tension of the belts and adjust it if necessary.

Electrical components

Check all electrical components for correct earthing and proper connection of all connectors;
refasten them if necessary.

Fuse replacement

Locate the fuse, which protects the lamp and electronics, in the base of the XR8.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.

16- DMX PROTOCOL

16 CHANNEL MODE ( 16bit)

1 PAN ms b ( 5 4 0°)
2
3
4 TILT l s b
5
6 D IM MER
7 SHU T T ER
8 C OL OUR
9 C YAN
10 MAGENTA
11 YEL L O W
12 SPEED CMY / DIMMER
13 MACRO CMY / COLOUR
14 E FF ECTS
15 ZOOM
16 RESET

DMX CHANNEL

DMX CHANNEL

DMX CHANNEL

DMX CHANNEL

DMX CHANNEL

PAN lsb

TILT msb(320°)

MOVEMENT SPEED

1

2

3

4

5

Parameter:

Parameter:

Parameter:

Parameter:

Parameter:

17

PAN msb 540°

PAN lsb

TILT msb 319°

TILT lsb

MOVEMENT SPEED

XR 5 WASH

ARC 1200

DMX range

Value

0-10

11-25

26-127

128-247

248-255

DMX CHANNEL

DMX range

Value

0-8

9-255

Mid point

DMX value

6

Parameter:

Mid point

DMX value

Move

range

(degrees)

DIMMER

Move

range

(degrees)

Mode Option Function

Standard

Fast movement

Vector mode from fast to slow

Variable time reaction to

DMX signal ( fast to slow)

Slow reaction time to DMX

signal

Mode Option Function

Black-out

Proportional dimmer

-

18

DMX CHANNEL

DMX range

Value

7

Parameter:

Mid point

DMX value

SHUTTER

Move

range

(degrees)

Mode Option Function

0-9
10-23
24-37
38-51
52-65
66-79
80-93

94-107
108-121
122-135
136-149
150-163
164-177
178-191
192-205
206-219
220-227
228-233
234-255

DMX CHANNEL

8

Parameter:

COLOUR

Strobe random speed

Strobe speed 1 min.

Strobe speed 2
Strobe speed 3
Strobe speed 4
Strobe speed 5

Strobe speed 6 max.

Flash open speed 1 min.

Flash open speed 2
Flash open speed 3

Flash open speed 4 max.

Flash closed speed 1 min.

Flash closed speed 2
Flash closed speed 3

Flash closed speed 4 max.

Colours / Macros in black-out

Pan / Tilt in black-out

XR 5 WASH

ARC 1200

Black-out

Open

-

DMX range

Value

0-12
13-25
26-38
39-51
52-64
65-77
78-90

91-103
104-116
117-129
130-142
143-155
156-168
169-181
182-197
198-200
201-203
204-206
207-209

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

White

Colour 1 (3200° K)

Colour 2 (5600°K)

Colour 3

BiColour 3/4

Colour 4

BiColour 4/5

Colour 5

BiColour 5/6

Colour 6

BiColour 6/7

Colour 7

Bicolour 7/8

Colour 8

Bicolour 8/white

Right rotation speed 1 max.

Right rotation speed 2
Right rotation speed 3
Right rotation speed 4

-

210-212
213-215
216-218
219-221
222-224
225-228
229-231
232-234
235-237
238-240
241-243
244-246
247-249
250-252
253-255

DMX CHANNEL

9

Parameter:

CYAN

19

XR 5 WASH

ARC 1200

Right rotation speed 5
Right rotation speed 6
Right rotation speed 7
Right rotation speed 8

Right rotation speed 9 min

Stop

Left rotation speed 1 min.

Left rotation speed 2
Left rotation speed 3
Left rotation speed 4
Left rotation speed 5
Left rotation speed 6
Left rotation speed 7
Left rotation speed 8

Left rotation speed 9 max.

DMX range

Value

0-255

DMX CHANNEL

DMX range

Value

0-255

DMX CHANNEL

DMX range

Value

0-255

DMX CHANNEL

Mid point

DMX value

10

Parameter:

Mid point

DMX value

11

Parameter:

Mid point

DMX value

12

Parameter:

(degrees)

(degrees)

(degrees)

Move

range

Mode Option Function

MAGENTA

Move

range

Mode Option Function

YELLOW

Move

range

Mode Option Function

SPEED CMY / DIMMER

Proportional colour

Proportional colour

Proportional colour

DMX range

Value

0-7

8-255

Mid point

DMX value

(degrees)

Move

range

Mode Option Function

No Function

Variable speed from max to min

-

DMX CHANNEL

DMX range

Value

0-9
10-14
15-19
20-24
25-29
30-34
35-39
40-44
45-49
50-54
55-59
60-64
65-69
70-74
75-79

80-84
85-89
90-94

95-99
100-104
105-109
110-114
115-121
122-128
129-135

136-142
143-149
150-156
157-163
164-170
171-177
178-184
185-191
192-198
199-205

206-212
213-219
220-226
227-233
234-240
241-247
247-255

13

Parameter:

Mid point

DMX value

Move
range

(degrees)

20

MACRO CMY / COLOUR

Mode Option Function

XR 5 WASH

ARC 1200

No Function
Macro 1
Macro 2
Macro 3

Macro

Macro 4
Macro

Macro 5
Macro

Macro 6
Macro

Macro 7
Macro

Macro 8
Macro

Macro 9
Macro

Macro 10
Macro

Macro 11
Macro

Macro 12

Macro

Macro 13
Macro

Macro 14
Macro

Macro 15
Macro

Macro 16
Macro

Macro 17
Macro

Macro 18
Macro

Macro 19
Macro

Macro 20
Macro

Macro

Macros rainbow wait =

Macros rainbow wait = 0
Macros rainbow wait =

Macros rainbow wait = 2

21

Macros rainbow wait = 3
Macros rainbow wait = 4

Macros rainbow wait =

Macros rainbow wait = 5
Macros rainbow wait =

Macros rainbow wait = 6
Macros rainbow wait = 7

Macros rainbow wait = 8
Macros rainbow wait = 9
Macros rainbow wait = 10

Full colours rainbow wait = 0
Full colours rainbow wait = 2
Full colours rainbow wait = 3
Full colours rainbow wait = 4

Full colours rainbow wait = 5
Full colours rainbow wait = 6

Full colours rainbow wait = 7
Full colours rainbow wait = 8
Full colours rainbow wait = 9

Full colours rainbow wait = 10

-

DMX CHANNEL

DMX range

Value

14

Parameter:

Mid point

DMX value

EFFECTS

Move

range

(degrees)

0-19

20-39

40-255

DMX CHANNEL

DMX range

Value

0-225

DMX CHANNEL

15

Mid point

DMX value

16

Parameter:

ZOOM

Move

range

(degrees)

Parameter: LAMP / RESET

21

XR 5 WASH

Mode Option Function

No effect

Frost

Beam Shape

Mode Option Function

Proportional

ARC 1200

MODE 1 (DEFAULT)

DMX range

Value

0-9
10-60
61-129

130-179
180-200

201-239
240-255

MODE 2 (SAME AS XR 250 WASH)

DMX range

Value

Mid point

DMX value

154

190

220

247

Mid point

DMX value

5
30
95

0-29

Move
range

(degrees)

Move

range

(degrees)

30-85

86 - 170
171-235

236-255

Mode Option Function

Mode Option Function

No Effect

Lamp OFF (Active after 3 seconds)

No Effect

Lamp ON (Active after 3 seconds)

No Effect

Internal Motors Reset

Total Reset

No effect

Lamp OFF (active after 3

seconds)

Internal motor Reset

Total Reset

Lamp ON (active after 3

seconds)

-

17- COLOUR WHEEL

1

2

3

22

4

6

XR 5 WASH

ARC 1200

5

COL1

0507K004
CONV.FILTER CTO
TC3256

8

0507K003
CONV. FILTER CTB
DL542

COL6COL5

7

COL3COL2

0507C046.D01
WOOD SW 460

COL7

COL4

0507C051.D01
ORANGE LW590

COL8

0507C042.D01
GREEN WB5055

0507C047.D01
RED LW 640

0507C041.D01
DARK BLUE SW490

0507C053.D01
AMBER LW 550

-

NOTE

23

XR 5 WASH

ARC 1200

The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its
products without prior notice. D.T.S. assumes no responsibility for the use or application of the
products or circuits described herein.

MADE IN ITALY

*0517I094*

*0517I094*

D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy

Tel. [phone] Fax [phone] [e-mail] www.dts-lighting.it