Page 1
XR300 BEAM
XR300 BEAM FAR E.B.
(Cod. 03.MB002.EB.LF)
• FAR system • CMY • Electronic ballast
XR300 BEAM FAR
(Cod. 03.MB002.LF)
• FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B.
(Cod. 03.MB002.EB.L)
• CMY • Electronic ballast
User’s Manual Rel 1.2
XR300 BEAM BF
(Cod. 03.MB003.L)
• Electromagnetic ballast
GB
D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it
Made in Italy
Page 2
2
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
XR300 BEAM
ARC 1200
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
D.T.S.
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
D.T.S.
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
D.T.S.
sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
D.T.S.
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S
D.T.S.
Page 3
3
INDEX:
1- SYMBOLS 4
2- GENERAL WARNING 4
3- GENERAL WARRANTY CONDITION 4
4- TECHNICAL FEATURES 5
5- ACCESSORIES 7
6- IMPORTANT SAFETY INFORMATION 8
6.1 Fire prevention
6.2 Prevention of electric shock
6.3 Protection against ultraviolet radiation
6.4 Safety
6.5 Level of protection against the penetration of solid and liquid objects
7- MOUNTING THE LAMP 9
7.1 Lamp alignment
8- VOLTAGE AND FREQUENCY 10
9- INSTALLATION 10
9.1 Safety cable
9.2 Protection against liquids
9.3 Movement
9.4 Risk of fire
9.5 Forced ventilation
9.6 Ambient temperature
10- MAINS CONNECTION 11
10.1 Protection
11- DMX SIGNAL CONNECTION 12
11.1 DMX Addresses
11.2 Selecting the DMX address
12- FIRMWARE UPDATING 13
13- DISPLAY FUNCTIONS 14
14- ERROR MESSAGES 21
15- HIDDEN MENU 23
16- PAN & TILT SPEED 25
17- FANS SPEED 25
18- OPENING THE PROJECTOR HOUSING 26
19- REPLACING GOBOS 27
20- PERIODIC CLEANING 27
20.1 Lenses and reflectors
20.2 Fans and air passages
21- PERIODIC CONTROLS
22- DMX PROTOCOL 28
23- 8 MOTORS CONTROL CARD 52
24- PAN & TILT CARD 53
25- CABLES RESEND CARD
26- DISPLAY CARD
27- LAMP ON-OFF CONTROL CARD
28- ROTATING GOBO WHEEL 54
29- COLOUR WHEEL 55
30- GOBOS PROVIDED IN THE BOX AS STANDARD ACCESSORIES 57
XR300 BEAM
ARC 1200
Page 4
1- SYMBOLS
Graphic symbols used on this manual
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC SHOCK RISK
4
XR300 BEAM
ARC 1200
!
F
UV
2M
2- GENERAL WARNING
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON
INFLAMMABLE SURFACES”
THIS SYMBOL MEANS “RADIATION FROM THIS LAMP
CAN CAUSE DAMAGE TO EYES AND SKIN”
THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO
BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT
Read the instruction contained in this user manual carefully, as they give important information
regarding safety during installation , use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or experienced
person.
Always disconnect the device from the mains before replacing the lamp.
The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.
The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.
Page 5
5
XR300 BEAM
ARC 1200
4- TECHNICAL FEATURES
The XR300 BEAM is a new compact moving head with an extremely high light power, projecting a
parallel and very concentrated beam.
With its new optical unit, the XR300 BEAM generates 135.000 Lux at 5 metres, using only a 300 W
lamp, giving an exceptional balance between performance and power consumption.
The XR300 BEAM is designed for a wide range of professional applications, like concerts, shows, tours,
television, theatre, and big events. XR300 BEAM ensures in fact great flexibility in use, because in a
single projector it incorporates a range of functions normally available only on different units (long-throw
projectors with high-power lamps, PAR 64 ACL, moving heads).
The XR300 BEAM features a breakthrough in moving-head technology, dubbed Free Axis Rotation
("FAR"). The FAR system allows limitless pan and tilt rotation: the XR300 BEAM head rotates freely on
its axes, horizontally or vertically, without interruption, in either direction, never having to reverse motion.
The XR300 BEAM's ability to quickly and precisely select any point within its limitless sphere of
movement means faster looks and scene changes.
The XR300 BEAM also offers unmatched creative control to the lighting designer. Unique geometrical
designs, shapes, and scenes, unobtainable with conventional moving heads, are now possible for
application in concerts, theatres, studios, etc.
The FAR system is guaranteed and has been thoroughly tested.
The XR300 BEAM offers:
* Exceptional light power (135.000 Lux at 5 metres);
* The capacity to project a highly condensed and intense beam of light even over great distances, thanks
to the high efficiency of the new optical group;
* Variety of colours (CMY synthesis + 7-colour wheel + CTO);
* Customizable gobo wheel (7 rotating gobos);
* Insertable frost filter (soft edge);
* Unlimited Pan and Tilt movements (new FAR technology).
The XR300 BEAM is also the ideal light for a vast range of applications in which quiet operation is a
priority, thanks to its silent ventilation system and silent pan/tilt operation.
Access to every feature of the internal menu is simple and direct, thanks to the new user interface
featuring a LCD backlit graphic display (128 x 64).
XR300 BEAM FAR E.B.
(Cod. 03.MB002.EB.LF)
• FAR system • CMY • Electronic ballast
XR300 BEAM FAR
(Cod. 03.MB002.LF)
• FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B.
(Cod. 03.MB002.EB.L)
• CMY • Electronic ballast
XR300 BEAM BF
(Cod. 03.MB003.L)
• Electromagnetic ballast
Lamp
Philips MSD Gold 300/2 Mini FastFit (300W / 22.000 Lumens)
Automatic switching on of lamp in case of accidental switching off
Lamp on/off via DMX; reset via DMX
Optical group
135.000 Lux at 5 m (6° beam angle)
Fresnel lens (Ø 195 mm)
Dichroic glass reflector
Dimmer / shutter / strobo
Linear dimmer
Shutter
Strobe from 0,85 flash/sec to 10 flash/sec
Page 6
6
XR300 BEAM
ARC 1200
4- TECHNICAL FEATURES
Colours
CMY colour synthesis system (XR300 BEAM FAR E.B. / XR300 BEAM FAR / XR300 BEAM E.B.)+
colour wheel (7 colours + CTO) with linear selection for perfect 2-colour beams
Colour change with blackout sync; rainbow effect
Gobos
1 customizable rotating gobo wheel (7 gobos); extractable gobo holders
Gobo change with synchronized blackout
Gobo scrolling; Gobo shake
Frost
Linear frost filter (soft edge)
Pan / Tilt
Unlimited Pan rotation; unlimited Tilt rotation (XR300 BEAM FAR E.B. / XR300 BEAM FAR)
Pan 540° (3,9 sec.), Tilt 270° (2,6 sec.) (XR300 BEAM E.B. / XR300 BEAM BF)
16-bit resolution
8 selectable speed ranges; extremely smooth and precise movements even at the highest speeds
Pan / Tilt locking system with recessed buttons
Automatic Pan/Tilt repositioning in case of knocks
DMX / Network
23 DMX channels (XR300 BEAM FAR E.B. / XR300 BEAM FAR / XR300 BEAM E.B.)
16 DMX channels (XR300 BEAM BF)
Internal operating system updatable via DMX
Interface
LCD (128x64) backlit graphic display (XR300 BEAM FAR E.B. / XR300 BEAM FAR / XR300 BEAM E.B.)
4 -eight digit- LED display with 4 buttons.
Connections
4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik; POWERCONN connector by
Neutrik
Power supply
Electronic ballast; 90-260 V (50/60 Hz); power consumption: 400 W
(XR300 BEAM FAR E.B. / XR300 BEAM E.B.)
Electromagnetic ballast: 230 V (50/60 Hz);
(XR300 BEAM FAR / XR300 BEAM BF)
Power saving mode (the lamp dims to 50% six seconds after shutter closure)
(XR300 BEAM FAR E.B. / XR300 BEAM E.B.)
Standard accessories
2 x “C” GQuick clamps with “fastlock” connection
Philips MSD Gold 300/2 Mini FastFit Lamp 05S
1 x (cod. 05 028)
•1 x POWERCONN male cable connector (cod. 0520P014)
•1 x XLR 5 Pins male cable connector (cod. 0508B028)
•1 x XLR 5 Pins female cable connector (cod. 0508B027)
•5 x Metal Gobos
Thermal Operating ambient temperature: -10° / 40°
Dimensions (WxDxH) 485x450x637 mm
Weight
25 Kg XR300 BEAM FAR E.B. / XR300 BEAM E.B.
31 Kg XR300 BEAM BF
34Kg XR300 BEAM FAR
(XR300 BEAM BF)
power consumption: 400 W
Approved lamps
Model Watt Base K° Lumens Life(h)
Osram Lok-it 300W 300 PGJX28 8.000 24.000 2.000
Philips MSD Gold 300/2 Mini FastFit
300 PGJX28 8.400 22.000 2.000
Page 7
4- TECHNICAL FEATURES
Dimensions
7
XR300 BEAM
ARC 1200
Packaging Dimensions (LxWxH)
550
x 440 x 800 mm
Weight:
32 Kg XR300 BEAM FAR E.B. / XR300 BEAM E.B.
38 Kg XR300 BEAM BF
41Kg XR300 BEAM FAR
5- ACCESSORIES
Unit Dimensions (LxWxH)
485x450x637mm
Weight:
25 Kg XR300 BEAM FAR E.B. / XR300 BEAM E.B.
31 Kg XR300 BEAM BF
34Kg XR300 BEAM FAR
As standard
Philips MSD Gold 300/2 Mini FastFit Lamp 05S
•1 x (cod. 05 028)
•1 x POWERCONN male cable connector (cod. 0520P014)
•1 x XLR 5 Pins male cable connector (cod. 0508B028)
•1 x XLR 5 Pins female cable connector (cod. 0508B027)
•5 x Metal Gobos
•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• User’s manual
Optional (on request)
Flight cases
• Double Professional Flight case; compartment for lamps and accessories, swivel wheels, cover with
hinges with-stay, dishes on cover for piling, 8 handles (2 each
side) (cod. 0521C032)
Rain covers
• Rain cover for XR base (top) (cod. 03.MA001)
• Rain cover for XR base (bottom) (cod. 03.MA002)
Embedding flanges
• Embedding flange for XR (visible display) (cod. 03.MA005)
• Embedding flange for XR (no visible display) (cod. 03.MA006)
Wireless DMX receivers retrofits
• Wireless DMX Receiver Card with 0508A033 - INDOOR IP20 2-dBi antenna included
Clamps / safety wires
• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)
• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)
• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)
• Omega clamp with “Fast Lock” connection 1⁄4 turn 1 couple (2 pieces) (Cod. 02K00467)
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)
Page 8
8
XR300 BEAM
ARC 1200
6- IMPORTANT SAFETY INFORMATION
6.1 Fire prevention:
XR300 BEAM uses a
(Alternative approved lamp: )
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1.5 MT.
-Minimum distance from the closest illuminable surface: 2 MT.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
6.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head, including lamp replacement.
-The level of technology inherent in the requires the assistance of specialised personnel for
all servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
Philips MSD Gold 300/2 Mini FastFit
Osram Lok-it 300W
lamp
F
XR300 BEAM
2M
6.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
6.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
!
UV
6.5 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid objects is IP 20.
For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:
• Rain cover for XR base (top) (cod. 03.MA001)
• Rain cover for XR base (bottom) (cod. 03.MA002)
!
Page 9
7- MOUNTING THE LAMPS
Warning: Switch off the unit before replacing the lamp.
9
XR300 BEAM
ARC 1200
Philips MSD Gold 300/2 Mini FastFit
Power 300W
Luminous flux 22,000 lm
Colour temperature 8.400°K
Lampbase PGJX28
Rated life 2000 hours
1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .
Osram Lok-it 300W
Power 300W
Luminous flux 24,000 lm
Colour temperature 8.000°K
Lampbase PGJX28
Rated life 2000 hours
Photo 2Photo 1 Photo 4Photo 3
2) Insert the lamp (photo2).
3) Rotate the lamp 1/4 turn clockwise (photo 3 and 4).
The lamp used on XR300 BEAM is made in quartz glass and should be handled with care. Always follow
the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue
provided in the lamp's packaging. The lamp socket is symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat
the procedure.
4) Replace the metal cover and tighten the screws A,B,C, which were previously removed.
WARNING: Never look directly at the lamp when it’s lit.
Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.
GJX28
UV
7.1 Lamp alignment
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic
filters and other components inside the unit. The lamp alignment is also essential to obtain the
maximum uniformity and luminous performance by the projection.
Lamp
Alignment
1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface
no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto
the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the
Z (photo 5)
When the lamp is correctly optimized,
zones wich are brighter than others.
until you achieve a uniform flat field.
you will have an evenly projected light beam, with no shadows or
Photo 5
3 adjusters X, Y and
Page 10
10
XR300 BEAM
ARC 1200
8- VOLTAGE AND FREQUENCY
The XR300 BEAM with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.
The XR300 BEAM with Electromagnetic ballast can operate at 230 VOLT 50 or 60 Hz.
9- INSTALLATION
XR300 BEAM may be either floor or ceiling mounted.
For floor mounting installations, the XR300 BEAM is supplied with four rubber mounting feet on the
base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake whilst the XR300 BEAM is moving.
Eight 1/4 turn Fast Locks connections placed in the base of the units allow to fix the XR300 BEAM in any
position, by using the two Fast Lock ‘C’ clamps provided in the box.
.
9.1- Safety cable
We recommend the use of a safety cable or chain connected to the XR300 BEAM and to the suspension
truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the
iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the
picture below.
A
9.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.
Page 11
11
XR300 BEAM
ARC 1200
9.3- Movement
Unlimited Pan rotation; unlimited Tilt rotation (XR300 BEAM FAR E.B. / XR300 BEAM FAR)
Pan 540° (3,9 sec.), Tilt 270° (2,6 sec.) (XR300 BEAM E.B. / XR300 BEAM BF)
Free Axis Rotation ("FAR")
!
WARNING
Do not place any object in the path
of the projector’s movement
270°
540°
9.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
No Free Axis Rotation ("FAR")
F
Minimum distance from the object being illuminated is 2 MT.
9.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on both the
base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the
projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
9.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.
10- MAINS CONNECTION
XR300 BEAM with electronic ballast operate at 90-260 VOLT 50-60 Hz.
XR300 BEAM with Electromagnetic ballast operate at 230 VOLT
50 or 60 Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is capable of supporting 5 amps at 230V,
Or 10 amps at 100-120 V
Strict adherence to regulatory norms is strongly recommended.
2M
Electronic ballast
90-260V 50 / 60Hz
Electromagnetic ballast
10.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each XR300 BEAM.
A good earth connection is essential for the correct operation of the projector.
230V 50 / 60Hz
!
Page 12
12
XR300 BEAM
ARC 1200
11- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR
5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable
ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it
to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
This way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
CONTROLLER
S TA ND AR D
D M X 5 1 2
5
1
1=GND
2=DATA3=DATA+
4 2
3
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
5
4
120 ohm
1
2
3
OUT
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
PIN 3
PIN 2
Page 13
13
XR300 BEAM
ARC 1200
11.1-DMX Addresses
XR300 BEAM FAR E.B, XR300 BEAM FAR, XR300 BEAM E.B, can be controlled with 23 (default) or
18 DMX channels.
XR300 BEAM BF, can be controlled with 17 (default) or 16 DMX channels.
If you want to use the unit in 23 channels, set the following addresses on the mixer:
Projector 1 A001
Projector 2 A024 If you want to select the next projector, just add “23”
Projector 3 A047
….. A….
projector 6 A116
If you want to use the unit in 17 channels, set the following addresses on the mixer:
Projector 1 A001
Projector 2 A018 If you want to select the next projector, just add “16”
Projector 3 A035
….. A….
projector 6 A086
11.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now setted to the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.
12 FIRMWARE UPDATING
Warning:
This procedure require a base knolewge of computer applications and Windows
Hyperterminal program.
To update the software version of the you need:
D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).
USB-DMX Drivers for the D.T.S. RED BOX interface .
(The drivers and the installation procedure are available in our web site www.dts-lighting.it)
Please refer to an authorised DTS service centre.
XR300 BEAM
!
‘Updating the software version’
Please follow the procedure below to perform the update:
1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.
2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
4. Download the new software version into the unit by using Windows Hyperterminal program.
It will be possible to download the software from the reserved area of D.T.S. web site:
Www.dts-lighting.it.
Page 14
14
XR300 BEAM
ARC 1200
13- DISPLAY FUNCTIONS
XR300 BEAM FAR E.B. (Cod. 03.MB002.EB.LF) • FAR system • CMY • Electronic ballast
XR300 BEAM FAR (Cod. 03.MB002.LF) • FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B. (Cod. 03.MB002.EB.L) • CMY • Electronic ballast
DISPLAY
DMX IN
FUSE 5A T 5X20
MAINS
Electronic ballast
90-260V 50 / 60Hz
MENU
ENTER
UP
DOWN
DMX OUT
DMX OUT
DMX IN
DISPLAY FUNCTIONS
The XR300 BEAM display panel shows all the available functions . Using these functions, it is
possible to change some of the parameters and add some functions. Changing the DTS setting
can vary the functions of the unit so that it does not respond to the DMX 512 used to control it.
Carefully follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
Up-Down
Pan Direction
Menu
PAN DIRECTION
This menu allows to set the Pan
movement.
Normal or Reversed
Up-DownENTER
PAN DIRECTION
NORMAL
Pan movement Normal or Reversed
Default = Normal
ENTER
Menu
TILT DIRECTION
This menu allows to set the Pan
movement.
Normal or Reversed
Menu
PAN TILT SPEED
Pan Tilt Speed control (1-4)
Tilt Direction
Up-Down
Pan Tilt Speed
Up-Down
MENU ENTER DOWN UP
Up-DownENTER
TILT DIRECTION
Tilt movement Normal or Reversed
ENTER
Default = Normal
NORMAL
MENU ENTER DOWN UP
Up-DownENTER
PAN TILT SPEED
Pan Tilt Speed control
ENTER
Default = 4
4
MENU ENTER DOWN UP
Page 15
13- DISPLAY FUNCTIONS
15
XR300 BEAM
ARC 1200
Up-Down
Display
Menu
DISPLAY FLIP / STAND BY / CONTRAST
Display Flip:
Reverses display's reading depending on the
mounting position
(On the ground or suspended).
Display Standby:
To turn off the display (after 5 seconds)
Or leave it always on.
Display Contrast:
Display contrast regulation (1-16)
Up-DownENTER
DISPLAY
FLIP
FLIP
Display Flip
ON THE GROUND (Default)
SUSPENDED
ENTER
ON THE GROUND
MENU ENTER DOWN UP
DISPLAY
STANDBY
FLIP
OFF
MENU ENTER DOWN UP
DISPLAY
CONTRAST
FLIP
Display Standby
OFF = Display Standby disabled
(Default)
ON = Display goes OFF after 5
seconds
Display Contrast
1-16 (Default = 8)
ENTER
ENTER
8
MENU ENTER DOWN UP
Up-Down
Up-Down
DMX Mode
Lamp
Menu
DMX MODE
To select DMX mode :
23 channels or 18 channels
Menu
LAMP
Lamp always ON, always OFF,
lamp ON-OFF selectable via DMX
And lamp life time reset
ADJUST
To adjust the lamp with no mixer
connected.
It’s possible to set the parameters for
PAN-TILT and ZOOM
Up-DownENTER
DMX MODE
DMX mode
ENTER
21 channels (Default)
18 channels
23 channels
MENU ENTER DOWN UP
Up-DownENTER
MENU
LAMP
BY DMX
FLIP
DOWN
ENTER
UP
LAMP
ADJUST
FLIP
BY DMX = ON / OFF via DMX (default)
ALWAYS ON = Forced ON
ALWAYS OFF = Forced OFF
RESET COUNTER = Lamp life time
reset
LAMP ADJUST =
To adjust the lamp
with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and ZOOM
ENTER
ENTER
MENU
ENTER
DOWN
UP
Page 16
13- DISPLAY FUNCTIONS
16
XR300 BEAM
ARC 1200
Menu
RESET
Reset via DMX ENABLED / DISABLED
and unit reset
Menu
FAN SPEED
Fan Speed control
Menu
GOBO ROTATION
Gobo rotation control the Rotating speed of gobo
Reset
Up-Down
Fan Speed
Up-Down
Gobo Rotation
Up-Down
Up-DownENTER
RESET
BY DMX
ENABLED
MENU ENTER DOWN UP
Up-DownENTER
FAN SPEED
ENABLED = Reset via DMX enabled
(Default)
DISABLED = Reset via DMX disabled
NOW = Unit motors reset
Fan speed control
ENTER
ENTER
1-5 (Default = 5)
5
MENU ENTER DOWN UP
Up-DownENTER
GOBO ROTATION
During gobo scrolling
ON
OFF = (Default)
ENTER
OFF
MENU ENTER DOWN UP
Menu
CMY BLACKOUT
CMY filters blades inserted at 100% if the dimmer
remain closed for more than 5 seconds.
By activating this function, it will be possible to
reduce substantially any visible light reflection
coming out from the front lens when dimmer is
closed.
Menu
SYSTEM INFO
Lamp life time, lamp strikes, unit life time, 8
motors card software version, Pan&Tilt card
software version and unit model
Menu
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
System Reboot
(Code = 100)
CMY Blackout
Up-Down
System info
Up-Down
Reserved
Up-Down
Up-DownENTER
CMY BLACKOUT
ON = Blackout enabled
ENTER
OFF = Blackout disabled (Default)
OFF
MENU ENTER DOWN UP
Up-DownENTER
Up-DownENTER
SYSTEM INFO
LAMP LIFE:0000H STRIKE:001
UNIT LIFE: 0010H
8M R.20
PT R.17
MODEL: XR300 BEAM
MENU ENTER DOWN UP
RESERVED
ENTER CODE
000
MENU ENTER DOWN UP
PAN LOCK
NO
SYSTEM INFO
Lamp life time, lamp strikes, unit life
time, 8 motors card software
version, Pan&Tilt card software
version and unit model
Pan Lock = Lock the Pan to the
desired value
Tilt Lock = Lock the Tilt to the
desired value
Pan Free = Remove power to Pan
motor
Tilt Free = Remove power to Tilt
motor
System Reboot = Unit Reboot
without needing of turning OFF the
unit
ENTER
ENTER
MENU ENTER DOWN UP
Page 17
13- DISPLAY FUNCTIONS
17
XR300 BEAM
ARC 1200
Up-Down
Up-Down
Default
Motors Test
Menu
DEFAULT
To restore main settings
Menu
TEST MODE
Full test and single function test.
Up-DownENTER
DEFAULT
RESTORE MAIN SETTINGS
MENU ENTER DOWN UP
Default
To restore main settings
ENTER
DEFAULT
RESTORE MAIN SETTINGS
SURE?
PRESS ENTER TO CONFORM
PRESS MENU TO CANCEL
MENU ENTER DOWN UP
Up-DownENTER
MOTORS TEST
ALL
MENU ENTER DOWN UP
Motors Test
ALL ,PAN, TILT, DIMMER, SHUTTER,
COLOUR WHEEL, CYAN, MAGENTA,
YELLOW and FROST.
ENTER
Page 18
18
13- DISPLAY FUNCTIONS
XR300 BEAM BF (Cod. 03.MB003.L) • Electromagnetic ballast
DISPLAY
MAINS
Electromagnetic ballast
230V 50 / 60Hz
FUSE 5A T 5X20
XR300 BEAM
ARC 1200
DMX IN
DMX OUT
DMX OUT
DMX IN
MENU
ENTER
UP
DOWN
DISPLAY FUNCTIONS
The XR300 BEAM display panel shows all the available functions . Using these functions, it is
possible to change some of the parameters and add some functions. Changing the DTS setting
can vary the functions of the unit so that it does not respond to the DMX 512 used to control it.
Carefully follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
Up-DownMENU ENTERUp-Down
PAN MOVEMENT INVERSION
To reverse Pan movement from left
to right and vice versa
Up-Down
Up-DownMENU ENTERUp-Down
TILT MOVEMENT INVERSION
To reverse Tilt movement from
bottom upwards and vice versa
Up-Down
Clockwise
Counterclockwise
Clockwise
Counterclockwise
ENTER
ENTER
ENTER
ENTER
Up-Down
MENU ENTER
SPEED control
Pan Tilt Speed control.
MENU
REVERSE DISPLAY
To Reverse display's reading depending
on the mounting position
(On the ground or suspended).
DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.
ENTERUp-Down
Up-Down
Up-Down
Up-Down
ENTER
ENTER
(DEFAULT : 4 )
Up-DownENTER
Up-DownENTER
Floor
position
Suspension
position
Display OFF
Display
always ON
ENTER
ENTER
ENTER
ENTER
Page 19
13- DISPLAY FUNCTIONS
19
XR300 BEAM
ARC 1200
Up-Down
DMX MODE
To select DMX mode : 17 or 16
channels
Up-Down
MENU
ENTER
LAMP
Lamp always ON-always OFF
Or lamp ON-OFF selectable via DMX
ADJUST
To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and FOCUS
STR
Lamp strikes counter
MENU
Up-Down
ENTER
RESET
Al motors reset
Up-DownMENU ENTER
Up-Down
Up-Down
Up-Down
17 CHANNELS
(Pan & Tilt 16 bit)
16 CHANNELS
(Pan & Tilt 16 bit)
ENTER
ENTER
ENTER
ENTER
ON / OFF VIA DMX (default)
FORCED ON
FORCED OFF
Up-Down
ENTER
RESET ENABLED VIA DMX
RESET DISABLED VIA DMX
ENTER
ENTER
(DEFAULT)
Up-Down
ENTER
ENTER
ENTER
MENU ENTER
Up-Down
Fan control
To control the fan speed .
MENU
Up-Down
.
ENTER
GOBO Rotation
Gobo Rotation during gobo scrolling
MENU
Up-Down
ENTER
SOFTWARE
Software version
Up-Down
Up-Down
Pcb 8 motors. Pcb PAN&TILT
ENTER
ENTER
ENTER
ENTER
TOTAL RESET
(DEFAULT : 5 )
GOBO ROTATION DISABLE (DEFAULT)
GOBO ROTATION ENABLE
ENTER
Page 20
13- DISPLAY FUNCTIONS
20
XR300 BEAM
ARC 1200
MENU
Up-Down
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
PAN LOCK
LOCK THE PAN TO THE DESIRED VALUE
TILT LOCK
LOCK THE TILT TO THE DESIRED VALUE
PAN FREE
REMOVE POWER TO PAN MOTOR
TILT FREE
REMOVE POWER TO TILT MOTOR
BOOT
System reboot
ENTER
Up-Down
Up-Down
.
.
.
.
ENTER
ENTER
ENTER
ENTER
Up-Down
Up-Down
Up-Down
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
Up-Down
Up-Down
Up-Down
MENU
Up-Down
ENTER
DEFAULT
To restore default setting
Up-Down
MENU ENTER
TEST MODE
Full test and single function test.
Up-Down
PAN
TILT
DIMMER
SHUTTER
GOBO1
ENTER
ENTER
GOBO1 ROT.
GOBO1 SHAKE
PRISM
EFFECTS ROT.
COLOR
Page 21
21
XR300 BEAM
ARC 1200
14- ERROR MESSAGES
XR300 BEAM FAR E.B. (Cod. 03.MB002.EB.LF) • FAR system • CMY • Electronic ballast
XR300 BEAM FAR (Cod. 03.MB002.LF) • FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B. (Cod. 03.MB002.EB.L) • CMY • Electronic ballast
ERROR
COLOUR WHEEL
MENU ENTER DOWN UP
COLOUR WHEEL
POSITION ERROR
ERROR
PAN
MENU ENTER DOWN UP
PAN REPOSITIONING
ENCODER ERROR
ERROR
CYAN
MENU ENTER DOWN UP
CYAN POSITION
ERROR
ERROR
TILT
MENU ENTER DOWN UP
TILT REPOSITIONING
ENCODER ERROR
ERROR
MAGENTA
MENU ENTER DOWN UP
MAGENTA POSITION
ERROR
ERROR
INTERNAL BUS
MENU ENTER DOWN UP
COMMUNICATION
PROBLEM BETWEEN 8
MOTORS CARD AND
PAN&TILT CARD
ERROR
YELLOW
MENU ENTER DOWN UP
YELLOW POSITION
ERROR
ERROR
DMX ADDRESS
MENU ENTER DOWN UP
DMX ADDRESS
ERROR
Page 22
22
14- ERROR MESSAGES
XR300 BEAM BF (Cod. 03.MB003.L) • Electromagnetic ballast
ERROR: ENCODER PAN
ERROR: ENCODER TILT
ERROR: DMX ADDRESS
ERROR: LOAD DATA EEPROM
ERROR: INTERNAL COMMUNICATION
ERROR: SYNCHRONIZED FREQUENCY MEASURE(SYNCHRONISM FOR LAMP ON)
XR300 BEAM
ARC 1200
ERROR: COLOR WHEEL POSITION
ERROR: GOBO WHEEL POSITION
ERROR: GOBO WHEEL INDEX
Page 23
23
XR300 BEAM
ARC 1200
15- HIDDEN MENU
XR300 BEAM FAR E.B. (Cod. 03.MB002.EB.LF) • FAR system • CMY • Electronic ballast
XR300 BEAM FAR (Cod. 03.MB002.LF) • FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B. (Cod. 03.MB002.EB.L) • CMY • Electronic ballast
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
- Reset the XR300 BEAM (reset from the MENU, not from the DMX controller!).
- While reset is running, press the MENU and ENTER keys at the same time.
CALIBRATION
MOTORS ALIGNMENT
PAN
134
MENU ENTER DOWN UP
ELECTRONIC
CALIBRATION OF THE
MOTORS
MIN LAMP POW.
1=65% 100=100%
10
MENU ENTER DOWN UP
LAMP POWER WHEN
DIMMER CLOSED
DEFAULT CAL
SET ALL MOTORS AT 128
MENU ENTER DOWN UP
RESET EEPROM.
RESET ALL SETTINGS
TO 128 VALUE
EXIT TO MAIN
MENU ENTER DOWN UP
EXIT FROM HIDDEN
MENU
FANS SPEED
ONLY AT MIN LAMP POWER
3
MENU ENTER DOWN UP
FAN SPEED WHEN
DIMMER CLOSED
Calibration mode
CALIBRATION
MOTORS ALIGNMENT
PAN
134
MENU ENTER DOWN UP
PAN ALIGNMENT
To align Pan position
CALIBRATION
MOTORS ALIGNMENT
TILT
167
MENU ENTER DOWN UP
TILT ALIGNMENT
To align Tilt position
CALIBRATION
MOTORS ALIGNMENT
GOBO
151
MENU ENTER DOWN UP
GOBO WHEEL ALIGNMENT
To align Gobo wheel
CALIBRATION
MOTORS ALIGNMENT
GOBO INDEX
141
MENU ENTER DOWN UP
GOBO WHEEL INDEX ALIGNMENT
To align Gobo wheel Index
Page 24
24
XR300 BEAM
ARC 1200
Calibration mode
XR300 BEAM FAR E.B. (Cod. 03.MB002.EB.LF) • FAR system • CMY • Electronic ballast
XR300 BEAM FAR (Cod. 03.MB002.LF) • FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B. (Cod. 03.MB002.EB.L) • CMY • Electronic ballast
CALIBRATION
MOTORS ALIGNMENT
COLOUR WHEEL
151
MENU ENTER DOWN UP
COLOUR WHEEL ALIGNMENT
To align Colour wheel
CALIBRATION
MOTORS ALIGNMENT
CYAN PATH
134
MENU ENTER DOWN UP
CYAN PATH ALIGNMENT
Cyan excursion setting
CALIBRATION
MOTORS ALIGNMENT
SHUTTER
145
MENU ENTER DOWN UP
SHUTTER ALIGNMENT
To align Shutter blades
CALIBRATION
MOTORS ALIGNMENT
MAGENTA ZERO
167
MENU ENTER DOWN UP
MAGENTA ZERO ALIGNMENT
Magenta zero position setting
CALIBRATION
MOTORS ALIGNMENT
FROST
85
MENU ENTER DOWN UP
FROST ALIGNMENT
To align Frost
CALIBRATION
MOTORS ALIGNMENT
MAGENTA PATH
151
MENU ENTER DOWN UP
MAGENTA PATH ALIGNMENT
Magenta excursion setting
CALIBRATION
MOTORS ALIGNMENT
CYAN ZERO
162
MENU ENTER DOWN UP
CYAN ZERO ALIGNMENT
Cyan zero position setting
CALIBRATION
MOTORS ALIGNMENT
YELLOW ZERO
141
MENU ENTER DOWN UP
YELLOW ZERO ALIGNMENT
Yellow zero position setting
CALIBRATION
MOTORS ALIGNMENT
YELLOW PATH
121
MENU ENTER DOWN UP
YELLOW PATH ALIGNMENT
Yellow excursion setting
Page 25
25
XR300 BEAM
ARC 1200
15- HIDDEN MENU
XR300 BEAM BF (Cod. 03.MB003.L) • Electromagnetic ballast
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
- Reset the XR300 BEAM (reset from the MENU, not from the DMX controller!).
- While reset is running, press the MENU and ENTER keys at the same time.
Electronic calibration of the motors.
Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must
repeat all previous calibrations)
Exit from hidden menu.
ENTER
Up-Down
PAN ALIGNMENT
To align pan
Up-Down
TILT ALIGNMENT
To align tilt
SHUTTER ALIGNMENT
To align shutter
GOBO WHEEL ALIGNMENT
To align gobo wheel
Up-Down
GOBO ROTATION ALIGNMENT
To align gobo ROTATION
COLOR ALIGNMENT
To align color wheel
Up-DownENTER
Up-DownENTER
Up-DownENTERUp-Down
Up-DownENTERUp-Down
Up-DownENTER
Up-DownENTERUp-Down
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
16- PAN & TILT SPEED (default: 4)
You can set the PAN and TILT motors at high speed on your XR300 BEAM.
Press menu until you see PAN TILT SPEED.
Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER.
17- FAN SPEED ( default: 5)
Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be
less than 35° C.
Page 26
26
XR300 BEAM
ARC 1200
18- OPENING THE PROJECTOR HOUSING
It is possible to inspect the inside of the projector by removing the cover as indicated below.
ATTENTION
REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.
1) Loosen the 2 1/4 turn fast lock screws which fix the head covers (photo 1) .
3) Once unscrewed, simply lift the covers to access the internal components (photo 2).
Photo 1
Photo 2
19- REPLACING GOBOS
XR300 BEAM uses a mechanical system which allows the fixture's gobos to be removed without the use
of special tools. Replacement gobos should be made of either heat resistant glass or metal.
An ever-increasing range of gobos is available from your DTS sales network.
Gobo dimensions are as follows:
ø external (ED) = 27.9 mm
ø of image with defined edge (ID) = 24 mm
thickness = from 0.2 to 4 mm (see catalogue)
Max thickness
4 mm
ID
ED
Coated side
When an object is held up the coated side of the glass gobo there
is no space between the object and its reflection.
Uncoated side
When an object is held up the uncoated side of the glass gobo
there is a space between the object and its reflection.
Load with coated surface toward the light source.
Coated side
Uncoated side
Page 27
27
Replacing gobos on the rotating gobo wheel
When replacing gobos, ensure that the projector is switched off.
1) Open the projector housing as described on page 26.
2) Remove the gobo holder to allow easier access to the gobo (photo 1).
3) Release the gobo retaining spring and carefully remove the gobo (photo 2).
4) Reverse the procedure to install a replacement gobo.
XR300 BEAM
ARC 1200
Photo 1
Photo 2
20- PERIODIC CLEANING
20.1- Lenses and reflectors
Even a fine layer of dust can reduce the luminous output substantially. Regularly clean all lenses
and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
20.2- Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning
will depend of course, on the conditions in which the projector is operating. Suitable instruments
for performing this type of maintenance are a brush and a common vacuum cleaner or an air
compressor. If necessary, clean the fans and air passages more frequently.
21- PERIODIC CONTROLS
!
Attention
Disconnect mains power prior to removing the projector housing.
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will
help to avoid the danger of the lamp exploding.
XR300 BEAM lamp lifespan is about 2000 hours, then it is necessary to replace it.
UV
Mechanical parts
Periodically check all mechanical parts,gears, guides, belts, etc.for wear and tear, replacing them if
necessary. Periodically check the lubrication of all components, particularly the parts subject to
high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.
distributor. Check the tension of the belts and adjust it if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors,
refastening if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the XR300 BEAM
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.
Page 28
28
XR300 BEAM
ARC 1200
22- DMX PROTOCOL
XR300 BEAM FAR E.B. (Cod. 03.MB002.EB.LF) • FAR system • CMY • Electronic ballast
XR300 BEAM FAR (Cod. 03.MB002.LF) • FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B. (Cod. 03.MB002.EB.L) • CMY • Electronic ballast
23 CHANNELS MODE (DEFAULT)
1 PAN msb 540°
2 PAN lsb
3 TILT msb 270°
4 TILT lsb
5 SPEED MOVEMENT
6 PAN FAR
7 TILT FAR
8 DIMMER
9 SHUTTER
10 COLOUR
11 COLOUR mode
12 CYAN
13 MAGENTA
14 YELLOW
15 SPEED CMY
16 MACRO CMY
17 GOBO
18 GOBO MODE
19 GOBO ROTATION/INDEX
20 GOBO INDEX FINE
21 GOBO SHAKE
22 EFFECTS
23 RESET - LAMP
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
1
Parameter: PAN msb
2
Parameter: PAN lsb
3
Parameter: TILT msb
4
Parameter: TILT lsb
5
Parameter: SPEED MOVEMENT
DMX range
Value
000 - 010
011-025
026-127
128-247
248-255
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Standard
Fast movement
Vector mode from fast to slow
Variable time reaction to
DMX signal ( fast to slow)
Slow reaction time to dmx signal
Page 29
DMX CHANNEL
DMX range
Value
000-010
011-020
021-030
031-040
041-050
051-060
061-070
071-080
081-090
091-100
101-110
111-120
121-182
183-193
194-255
6
Mid point
DMX value
Parameter: PAN FAR
Move
range
(degrees)
29
XR300 BEAM
ARC 1200
Mode Option Function
Position mode 540° (standard path)
Position mode 360° ( 1 turn)
Position mode 720° ( 2 turns)
Position mode 1080° ( 3 turns)
Position mode 1440° ( 4 turns)
Position mode 1800° ( 5 turns)
Position mode 2160° ( 6 turns)
Position mode 2520° ( 7 turns)
Position mode 2880° ( 8 turns)
Position mode 3240° ( 9 turns)
Position mode 3600° (10 turns)
Position mode 360° smart path
Forward spin rotation speed from max to min
Stop
Reverse spin rotation speed from min to max
DMX CHANNEL
DMX range
Value
000-010
011-020
021-030
031-040
041-050
051-060
061-070
071-080
081-090
091-100
101-110
111-120
121-182
183-193
194-255
7
Mid point
DMX value
Parameter: TILT FAR
Move
range
(degrees)
Mode Option Function
Forward spin rotation speed from max to min
Reverse spin rotation speed from min to max
Position mode 270° (standard path)
Position mode 360° ( 1 turn)
Position mode 720° ( 2 turns)
Position mode 1080° ( 3 turns)
Position mode 1440° ( 4 turns)
Position mode 1800° ( 5 turns)
Position mode 2160° ( 6 turns)
Position mode 2520° ( 7 turns)
Position mode 2880° ( 8 turns)
Position mode 3240° ( 9 turns)
Position mode 3600° (10 turns)
Position mode 360° smart path
Stop
DMX CHANNEL 8
DMX range
Value
Mid point
DMX value
0-7
8-255
Parameter: DIMMER
Move
range
(degrees)
Mode Option Function
Black-out
Proportional dimmer
Page 30
DMX CHANNEL 9
DMX range
Value
000-019
020-039
040-059
060-079
080-089
090-099
100-109
Mid point
DMX value
110-119
120-129
130-139
140-149
150-159
160-169
170-179
180-189
190-199
200-209
210-219
220-227
228-233
234-255
Parameter:
Move
range
(degrees)
SHUTTER
Mode Option Function
30
XR300 BEAM
ARC 1200
Black - out
Open
Black-out
Random Strobe
Strobe speed 1 min. (0,85 Hz)
Strobe speed 2 (1,4 Hz)
Strobe speed 3 (2 HZ)
Strobe speed 4 (3,75 Hz)
Strobe speed 5 (5 Hz)
Strobe speed 6 max. (6,75 Hz)
Pulse open speed 1 min.
Pulse open speed 2
Pulse open speed 3
Pulse open speed 4 max.
Pulse closed speed 1 min.
Pulse closed speed 2
Pulse closed speed 3
Pulse closed speed 4 max.
Colour and Gobo in black-out
Pan and Tilt in black-out
Open
DMX CHANNEL
DMX range
Value
0-27
28-55
56-83
84-111
112-139
140-167
168-195
196-223
224-255
10
Mid point
DMX value
Parameter: COLOUR
Move
range
(degrees)
IF CHANNEL 11 = FULL COLOUR (Dmx range value 0 - 63)
Mode Option Function
Colour1 (White)
Colour2
Colour3
Colour4
Colour5
Colour6
Colour7
Colour8
Colour9
Page 31
DMX CHANNEL 10
DMX range
Value
Mid point
DMX value
XR300 BEAM
ARC 1200
Parameter: COLOUR
Move
range
(degrees)
31
Mode Option Function
IF CHANNEL 11 = HALF COLOUR (Dmx range value 64 - 127)
0-25
26-51
52-77
78-103
104-129
130-155
156-181
182-207
208-233
234-255
IF CHANNEL 11 = PROPORTIONAL COLOUR (Dmx range value 128 - 191)
0-10
11-255
0-9
10-127
128-137
138-255
DMX CHANNEL 9
DMX CHANNEL 9
DMX CHANNEL 11
Parameter:
Parameter:
Parameter:
IF CHANNEL 11 = RAINBOW (Dmx range value 192 - 255)
Right Rot.Speed from Max to Min
Left Rot.speed from Min to Max
Colour1 (White)
Bicolour ½
Bicolour 2/3
Bicolour 3/4
Bicolour 4/5
Bicolour 5/6
Bicolour 6/7
Bicolour 7/8
Bicolour 8/9
Bicolour 9/1
Colour1 (White)
Proportional colour
No Colour (White)
Stop
COLOUR MODE
DMX range
DMX range
Value
Value
000 - 063
064 - 127
128 - 191
192 - 255
DMX CHANNEL 12
DMX range
Value
000 - 255
DMX CHANNEL 13
DMX range
Value
000 - 255
Mid point
Mid point
DMX value
DMX value
Mid point
DMX value
Mid point
DMX value
Move
Move
range
range
(degrees)
(degrees)
Parameter: CYAN
Move
range
(degrees)
Parameter: MAGENTA
Move
range
(degrees)
Mode Option Function
Mode Option Function
Mode Option Function
Mode Option Function
Full colour
Full colour
Half colour
Half colour
Proportional colour
Rainbow
Rainbow
Proportionall colour
Proportional colour
Page 32
DMX CHANNEL 11
DMX CHANNEL 11
DMX CHANNEL 14
DMX range
DMX range
DMX range
Value
Value
Value
000 - 255
DMX CHANNEL 15
DMX range
Value
000 - 007
008 - 255
DMX CHANNEL 16
DMX range
Value
000 - 009
010 - 014
015 - 019
020 - 024
025 - 029
030 - 034
035 - 039
040 - 044
045 - 049
050 - 054
055 - 059
Mid point
Mid point
Mid point
DMX value
DMX value
DMX value
Mid point
DMX value
Mid point
DMX value
Parameter: YELLOW
Parameter:
Move
Move
Move
range
range
range
(degrees)
(degrees)
(degrees)
Parameter: SPEED CMY
Move
range
(degrees)
Parameter: MACRO CMY
Move
range
(degrees)
060 - 064
065 - 069
070 - 074
075 - 079
080 - 084
085 - 089
090 - 094
095 - 099
100-104
105-109
110-114
115-121
122-128
129-135
136-142
143-149
150-156
157-163
164-170
171-177
32
Mode Option Function
Mode Option Function
Mode Function
XR300 BEAM
ARC 1200
Proportional colour
Mode Option Function
No function
Variabile speed from max to min
Mode Option Function
No function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro6
Macro 7
Macro 8
Macro 9
Macro 10
Macro11
Macro 12
Macro 13
Macro 14
Macro 15
Macro 16
Macro17
Macro 18
Macro 19
Macro 20
Macro 21
Macro rainbow wait = 0
Macro rainbow wait = 2
Macro rainbow wait = 3
Macro rainbow wait = 4
Macro rainbow wait = 5
Macro rainbow wait = 6
Macro rainbow wait = 7
Macro rainbow wait = 8
Macro rainbow wait = 9
Page 33
DMX CHANNEL 16
DMX range
Value
178-185
186-192
193-199
200-206
207-213
114-220
221-227
228-234
235-241
242-248
249-255
DMX CHANNEL
Mid point
DMX value
17
Parameter: MACRO CMY
Move
range
(degrees)
Parameter: GOBO
Mode Option Function
33
Macro rainbow wait = 10
Full colours rainbow = 0
Full colours rainbow = 2
Full colours rainbow = 3
Full colours rainbow = 4
Full colours rainbow = 5
Full colours rainbow = 6
Full colours rainbow = 7
Full colours rainbow = 8
Full colours rainbow = 9
Full colours rainbow = 10
XR300 BEAM
ARC 1200
DMX range
Value
0-25
26-51
52-77
78-103
104-129
130-155
156-181
182-207
208-213
214-219
220-225
226-231
232-237
238-243
244-249
250-255
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Rotation speed 1 min.
Rotation speed 2
Rotation speed 3
Rotation speed 4
Rotation speed 5
Rotation speed 6
Rotation speed 7
Rotation speed 8 Max
DMX CHANNEL
DMX range
Value
0-127
128-255
18
Mid point
DMX value
Parameter: GOBO MODE
Move
range
(degrees)
Mode Option Function
Gobo Rotation Mode
Gobo Index Mode
Page 34
DMX CHANNEL 19
DMX range
Value
Mid point
DMX value
34
Parameter: GOBO ROTATION/GOBO INDEX COARSE
Move
range
(degrees)
Mode Option Function
XR300 BEAM
ARC 1200
IF CHANNEL 18 = Gobo Rotation Mode (Dmx range value 0 - 127)
0-9
10-127
128-137
138-255
0-255
DMX CHANNEL
DMX range
Value
0-255
DMX CHANNEL
DMX range
Value
0-9
10-22
23-35
36-48
49-61
62-74
75-87
88-100
101-113
114-126
127-138
139-151
152-164
165-177
178-190
191-203
204-216
217-229
230-242
243-255
IF CHANNEL 18 = Gobo Index Mode (Dmx range value 128 - 255)
20
Mid point
DMX value
21
Mid point
DMX value
Parameter: GOBO INDEX FINE
Move
range
(degrees)
Parameter: GOBO 1 SHAKE
Move
range
(degrees)
Mode Option Function
Mode Option Function
Stop
SX Rot. Prop. Speed Max to Min
Stop
DX Rot. Prop. Speed Min to Max
Gobo index Coarse
Gobo Index Fine
Stop
Gobo Shake R-L Speed 1 Min.
Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
Gobo Shake R-L Speed 4
Gobo Shake R-L Speed 5
Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7
Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2
Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4
Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
Gobo Shake L-R Speed 9 Max
Page 35
DMX CHANNEL 22
DMX range
Value
000-009
010-029
030-245
246-255
Mid point
DMX value
Parameter: EFFECTS
Move
range
(degrees)
35
Mode Option Function
XR300 BEAM
ARC 1200
No function
Diffuser
Linear Frost
Frost fully inserted
DMX CHANNEL 23
DMX range
Value
0-9
10-60
61-129
130-179
180-200
201-239
240-255
Mid point
DMX value
Parameter: RESET / LAMP
Move
range
Mode
(degrees)
Option
Function
No Effect
Lamp OFF (activ.after 3 seconds)
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
Internal motor reset
Total Reset
Page 36
36
XR300 BEAM
ARC 1200
23 DMX PROTOCOL
XR300 BEAM FAR E.B. (Cod. 03.MB002.EB.LF) • FAR system • CMY • Electronic ballast
XR300 BEAM FAR (Cod. 03.MB002.LF) • FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B. (Cod. 03.MB002.EB.L) • CMY • Electronic ballast
18 CHANNELS MODE
1 PAN msb 540°
2 PAN lsb
3 TILT msb 270°
4 TILT lsb
5 SPEED MOVEMENT
6 PAN FAR
7 TILT FAR
8 DIMMER
9 SHUTTER
10 COLOUR
11 CYAN
12 MAGENTA
13 YELLOW
14 GOBO
15 GOBO ROTATION/INDEX
16 GOBO SHAKE
17 EFFECTS
18 RESET - LAMP
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX range
Value
0-10
11-25
26-127
128-247
248-255
1
2
3
4
5
Mid point
DMX value
Parameter: PAN msb
Parameter: PAN lsb
Parameter: TILT msb
Parameter: TILT lsb
Parameter: SPEED MOVEMENT
Move
range
(degrees)
Mode Option Function
Standard
Fast movement
Vector mode from fast to slow
Variable time reaction to
DMX signal ( fast to slow)
Slow reaction time to dmx signal
Page 37
DMX CHANNEL
DMX range
Value
000-010
011-020
021-030
031-040
041-050
051-060
061-070
071-080
081-090
091-100
101-110
111-120
121-182
183-193
194-255
6
Mid point
DMX value
Parameter: PAN FAR
Move
range
(degrees)
37
XR300 BEAM
ARC 1200
Mode Option Function
Position mode 540° (standard path)
Position mode 360° ( 1 turn)
Position mode 720° ( 2 turns)
Position mode 1080° ( 3 turns)
Position mode 1440° ( 4 turns)
Position mode 1800° ( 5 turns)
Position mode 2160° ( 6 turns)
Position mode 2520° ( 7 turns)
Position mode 2880° ( 8 turns)
Position mode 3240° ( 9 turns)
Position mode 3600° (10 turns)
Position mode 360° smart path
Forward spin rotation speed from max to min
Stop
Reverse spin rotation speed from min to max
DMX CHANNEL
DMX range
Value
000-010
011-020
021-030
031-040
041-050
051-060
061-070
071-080
081-090
091-100
101-110
111-120
121-182
183-193
194-255
7
Mid point
DMX value
Parameter: TILT FAR
Move
range
(degrees)
Mode Option Function
Forward spin rotation speed from max to min
Reverse spin rotation speed from min to max
Position mode 270° (standard path)
Position mode 360° ( 1 turn)
Position mode 720° ( 2 turns)
Position mode 1080° ( 3 turns)
Position mode 1440° ( 4 turns)
Position mode 1800° ( 5 turns)
Position mode 2160° ( 6 turns)
Position mode 2520° ( 7 turns)
Position mode 2880° ( 8 turns)
Position mode 3240° ( 9 turns)
Position mode 3600° (10 turns)
Position mode 360° smart path
Stop
DMX CHANNEL 8
DMX range
Value
Mid point
DMX value
0-7
8-255
Parameter: DIMMER
Move
range
(degrees)
Mode Option Function
Black-out
Proportional dimmer
Page 38
DMX CHANNEL
DMX range
Value
0-19
20-39
40-59
60-79
80-89
90-99
100-109
110-119
120-129
130-139
140-149
150-159
160-169
170-179
180-189
190-199
200-209
210-219
220-227
228-233
234-255
9
Mid point
DMX value
Parameter: SHUTTER
Move
Mode Option Function
range
(degrees)
38
XR300 BEAM
ARC 1200
Black - out
Open
Black-out
Random Strobe
-out
Strobe speed 1 min. (0,85 Hz)
Strobe speed 2 (1,4 Hz)
Strobe speed 3 (2 HZ)
Strobe speed 4 (3,75 Hz)
Strobe speed 5 (5 Hz)
Strobe speed 6 max. (6,75 Hz)
Pulse open speed 1 min.
Pulse open speed 2
Pulse open speed 3
Pulse open speed 4 max.
Pulse closed speed 1 min.
Pulse closed speed 2
Pulse closed speed 3
Pulse closed speed 4 max.
Colour and Gobo in black-out
Pan and Tilt in black
Open
DMX CHANNEL 10
DMX range
Value
0-12
13-25
26-38
39-51
52-64
65-77
78-90
Mid point
DMX value
Parameter: COLOUR
Move
range
(degrees)
Mode Option Function
Colour1 (White)
Colour 2 (HALF CTO)
Colour 3 (CTO)
Colour 4
Colour 4/5
Colour 5
Colour 5/6
Page 39
39
XR300 BEAM
ARC 1200
DMX CHANNEL 10
DMX range
Value
091 - 103
104 - 116
117 - 129
130 - 142
143 - 155
156 - 168
169 - 181
182 - 197
198 - 200
201 - 203
204 - 206
207 - 209
210 - 212
213 - 215
216 - 218
219 - 221
222 - 224
225 - 228
229 - 231
232 - 234
235 - 237
238 - 240
241 - 243
244 - 246
247 - 249
250 - 252
253 - 255
Mid point
DMX value
Parameter: COLOUR
Move
range
(degrees)
Mode Option Function
Colour 6
Colour 6/7
Colour 7
Colour 7/8
Colour 8
Colour 8/9
Colour 9
Colour 9/1
Right rotation speed 9 Max
Right rotation speed 8
Right rotation speed 7
Right rotation speed 6
Right rotation speed 5
Right rotation speed 4
Right rotation speed 3
Right rotation speed 2
Right rotation speed 1Min
Stop
Left rotation speed 1 Min
Left rotation speed 2
Left rotation speed 3
Left rotation speed 4
Left rotation speed 5
Left rotation speed 6
Left rotation speed 7
Left rotation speed 8
Left rotation speed 9 Max
DMX CHANNEL 11
DMX range
Value
0-255
DMX CHANNEL 12
DMX range
Value
0-255
Mid point
DMX value
Mid point
DMX value
Parameter: CYAN
Move
range
(degrees)
Parameter: MAGENTA
Move
range
(degrees)
Mode Option Function
Mode Option Function
Proportional colour
Proportional colour
Page 40
DMX CHANNEL 11
DMX CHANNEL 11
DMX CHANNEL 13
DMX range
DMX range
DMX range
Value
Value
Value
000 - 255
DMX CHANNEL
DMX range
Value
-
025
000
026
-
051
052-077
078-103
104-129
130-155
156-181
Mid point
Mid point
Mid point
DMX value
DMX value
DMX value
14
Mid point
DMX value
182-207
208-213
214-219
220-225
226-231
232-237
238-243
244-249
250-255
Parameter: YELLOW
Move
Move
Move
range
range
range
(degrees)
(degrees)
(degrees)
Parameter: GOBO
Move
range
(degrees)
40
Mode Option Function
Mode Option Function
Mode Option Function
Proportional colour
XR300 BEAM
ARC 1200
Mode Option Function
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Rotation speed 1 min.
Rotation speed 2
Rotation speed 3
Rotation speed 4
Rotation speed 5
Rotation speed 6
Rotation speed 7
Rotation speed 8 Max
DMX CHANNEL
DMX range
Value
000 - 127
128 - 180
118811 -- 220022
203 - 255
DMX CHANNEL
DMX range
Value
0-9
10-22
23-35
36-48
49-61
62-74
15
Mid point
DMX value
16
Mid point
DMX value
Parameter: GOBO ROTATION/INDEX
Move
range
(degrees)
Parameter: GOBO SHAKE
Move
range
(degrees)
Mode Option Function
Proportional index 0° - 360°
Left rotation
Stop
Right rotation
Mode Option Function
Stop
Gobo Shake R-L Speed 1 Min.
Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
Gobo Shake R-L Speed 4
Gobo Shake R-L Speed 5
Page 41
DMX CHANNEL
16
DMX range Mid point
Value DMX value
075-087
088-100
101-113
114-126
127-138
139-151
152-164
165-177
178-190
191-203
204-216
217-229
230-242
243-255
Parameter: GOBO SHAKE
Move
range Mode Option Function
(degrees)
41
Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7
Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2
Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4
Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
Gobo Shake L-R Speed 9 Max
XR300 BEAM
ARC 1200
DMX CHANNEL
DMX range
Value
000-009
010-029
030-245
246-255
DMX CHANNEL 18
DMX range Mid point
Value DMX value
0-9
10-60
61-129
130-179
180-200
201-239
240-255
17
Parameter: EFFECTS
Mid point
DMX value
Parameter: RESET / LAMP
Move
range
(degrees)
Mode Option Function
Move
range
Mode
(degrees)
Option
No function
Diffuser
Linear Frost
Frost fully inserted
Function
No Effect
Lamp OFF (activ.after 3 seconds)
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
Internal motor reset
Total Reset
Page 42
42
23 DMX PROTOCOL
XR300 BEAM BF (Cod. 03.MB003.L) • Electromagnetic ballast
17 CHANNELS MODE (DEFAULT)
1 PAN msb 540°
2 PAN lsb
3 TILT msb 270°
4 TILT lsb
5 SPEED MOVEMENT
6 DIMMER
7 SHUTTER
8 COLOUR
9 COLOUR mode
10 CTO
11 GOBO
12 GOBO MODE
13 GOBO ROTATION/INDEX
14 GOBO INDEX FINE
15 GOBO SHAKE
16 FROST
17 RESET - LAMP
XR300 BEAM
ARC 1200
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX range
Value
000 - 010
011-025
026-127
128-247
248-255
1
2
3
4
5
Mid point
DMX value
Parameter: PAN msb
Parameter: PAN lsb
Parameter: TILT msb
Parameter: TILT lsb
Parameter: SPEED MOVEMENT
Move
range
(degrees)
Mode Option Function
Standard
Fast movement
Vector mode from fast to slow
Variable time reaction to
DMX signal ( fast to slow)
Slow reaction time to dmx signal
Page 43
DMX CHANNEL 6
DMX range
Value
Mid point
DMX value
0-7
8-255
DMX CHANNEL
DMX range
Value
000-019
020-039
040-059
060-079
080-089
090-099
100-109
Mid point
DMX value
110-119
120-129
130-139
140-149
150-159
160-169
170-179
180-189
190-199
200-209
210-219
220-227
228-233
234-255
Parameter: DIMMER
Move
range
(degrees)
7
Parameter: SHUTTER
Move
range
(degrees)
43
XR300 BEAM
ARC 1200
Mode Option Function
Black-out
Proportional dimmer
Mode Option Function
Black - out
Open
Black-out
Random Strobe
Strobe speed 1 min. (0,85 Hz)
Strobe speed 2 (1,4 Hz)
Strobe speed 3 (2 HZ)
Strobe speed 4 (3,75 Hz)
Strobe speed 5 (5 Hz)
Strobe speed 6 max. (6,75 Hz)
Pulse open speed 1 min.
Pulse open speed 2
Pulse open speed 3
Pulse open speed 4 max.
Pulse closed speed 1 min.
Pulse closed speed 2
Pulse closed speed 3
Pulse closed speed 4 max.
Colour and Gobo in black-out
Pan and Tilt in black-out
Open
DMX CHANNEL 8
DMX range
Value
0-27
28-55
56-83
84-111
112-139
140-167
168-195
196-223
224-255
Mid point
DMX value
Parameter: COLOUR
Move
range
(degrees)
IF CHANNEL 9 = FULL COLOUR (Dmx range value 0 - 63)
Mode Option Function
Colour1 (White)
Colour2
Colour3
Colour4
Colour5
Colour6
Colour7
Colour8
Colour9
Page 44
DMX CHANNEL 8
DMX range
Value
Mid point
DMX value
XR300 BEAM
ARC 1200
Parameter: COLOUR
Move
range
(degrees)
44
Mode Option Function
IF CHANNEL 9 = HALF COLOUR (Dmx range value 64 - 127)
0-25
26-51
52-77
78-103
104-129
130-155
156-181
182-207
208-233
234-255
0-10
11-255
0-9
10-127
128-137
138-255
IF CHANNEL 9 = PROPORTIONAL COLOUR (Dmx range value 128 - 191)
IF CHANNEL 9 = RAINBOW (Dmx range value 192 - 255)
Right Rot.Speed from Max to Min
Left Rot.speed from Min to Max
Colour1 (White)
Bicolour ½
Bicolour 2/3
Bicolour 3/4
Bicolour 4/5
Bicolour 5/6
Bicolour 6/7
Bicolour 7/8
Bicolour 8/9
Bicolour 9/1
Colour1 (White)
Proportional colour
No Colour (White)
Stop
DMX CHANNEL 9
DMX CHANNEL 9
DMX CHANNEL 9
DMX range
DMX range
Value
Value
000 - 063
064 - 127
128 - 191
192 - 255
DMX CHANNEL 9
DMX CHANNEL 9
DMX CHANNEL 10
DMX range
DMX range
Value
Value
000 - 127
128 - 255
Mid point
Mid point
DMX value
DMX value
Mid point
Mid point
DMX value
DMX value
Parameter:
Parameter:
Parameter:
Move
Move
range
range
(degrees)
(degrees)
Parameter:
Parameter:
Parameter:
Move
Move
range
range
(degrees)
(degrees)
COLOUR MODE
Mode Option Function
Mode Option Function
CTO
Mode Option Function
Mode Option Function
Full colour
Full colour
Half colour
Half colour
Proportional colour
Rainbow
Rainbow
No Function
CTO
Page 45
DMX CHANNEL
DMX range
Value
0-25
26-51
52-77
78-103
104-129
130-155
156-181
182-207
208-213
214-219
220-225
226-231
232-237
238-243
244-249
250-255
XR300 BEAM
ARC 1200
11
Mid point
DMX value
Parameter: GOBO
Move
range
(degrees)
45
Mode Option Function
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Rotation speed 1 min.
Rotation speed 2
Rotation speed 3
Rotation speed 4
Rotation speed 5
Rotation speed 6
Rotation speed 7
Rotation speed 8 Max
DMX CHANNEL
DMX range
Value
0-127
128-255
DMX CHANNEL 13
DMX range
Value
0-9
10-127
128-137
138-255
0-255
DMX CHANNEL
12
Mid point
DMX value
Mid point
DMX value
14
Parameter: GOBO MODE
Move
range
(degrees)
Parameter: GOBO ROTATION/GOBO INDEX COARSE
Move
range
(degrees)
Mode Option Function
Gobo Rotation Mode
Gobo Index Mode
Mode Option Function
IF CHANNEL 12 = Gobo Rotation Mode (Dmx range value 0 - 127)
Stop
SX Rot. Prop. Speed Max to Min
Stop
DX Rot. Prop. Speed Min to Max
IF CHANNEL 12 = Gobo Index Mode (Dmx range value 128 - 255)
Parameter: GOBO INDEX FINE
Gobo index Coarse
DMX range
Value
0-255
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Gobo Index Fine
Page 46
DMX CHANNEL
DMX range
Value
0-9
10-22
23-35
36-48
49-61
62-74
75-87
88-100
101-113
114-126
127-138
139-151
152-164
165-177
178-190
191-203
204-216
217-229
230-242
243-255
15
Mid point
DMX value
Parameter: GOBO SHAKE
Move
(degrees)
range
Mode Option Function
46
Stop
Gobo Shake R-L Speed 1 Min.
Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
Gobo Shake R-L Speed 4
Gobo Shake R-L Speed 5
Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7
Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2
Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4
Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
Gobo Shake L-R Speed 9 Max
XR300 BEAM
ARC 1200
DMX CHANNEL
DMX range
Value
000-029
030-245
246-255
DMX CHANNEL 17
DMX range Mid point
Value DMX value
0-9
10-60
61-129
130-179
180-200
201-239
240-255
16
Parameter: FROST
Mid point
DMX value
Parameter: RESET / LAMP
Move
range
(degrees)
Mode Option Function
Move
range
Mode
(degrees)
Option
No function
Linear Frost
Frost fully inserted
Function
No Effect
Lamp OFF (activ.after 3 seconds)
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
Internal motor reset
Total Reset
Page 47
47
23 DMX PROTOCOL
XR300 BEAM BF (Cod. 03.MB003.L) • Electromagnetic ballast
XR300 BEAM BF (Cod. 03.MB003.L) • Electromagnetic ballast
16 CHANNELS MODE
1 PAN msb 540°
2 PAN lsb
3 TILT msb 270°
4 TILT lsb
5 SPEED MOVEMENT
6 DIMMER
7 SHUTTER
8 COLOUR
9 COLOUR mode
10 GOBO
11 GOBO MODE
12 GOBO ROTATION/INDEX
13 GOBO INDEX FINE
14 GOBO SHAKE
15 FROST
16 RESET - LAMP
XR300 BEAM
ARC 1200
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX range
Value
000 - 010
011-025
026-127
128-247
248-255
1
2
3
4
5
Mid point
DMX value
Parameter: PAN msb
Parameter: PAN lsb
Parameter: TILT msb
Parameter: TILT lsb
Parameter: SPEED MOVEMENT
Move
range
(degrees)
Mode Option Function
Standard
Fast movement
Vector mode from fast to slow
Variable time reaction to
DMX signal ( fast to slow)
Slow reaction time to dmx signal
Page 48
DMX CHANNEL 6
DMX range
Value
Mid point
DMX value
0-7
8-255
DMX CHANNEL
DMX range
Value
000-019
020-039
040-059
060-079
080-089
090-099
100-109
Mid point
DMX value
110-119
120-129
130-139
140-149
150-159
160-169
170-179
180-189
190-199
200-209
210-219
220-227
228-233
234-255
Parameter: DIMMER
Move
range
(degrees)
7
Parameter: SHUTTER
Move
range
(degrees)
48
XR300 BEAM
ARC 1200
Mode Option Function
Black-out
Proportional dimmer
Mode Option Function
Black - out
Open
Black-out
Random Strobe
Strobe speed 1 min. (0,85 Hz)
Strobe speed 2 (1,4 Hz)
Strobe speed 3 (2 HZ)
Strobe speed 4 (3,75 Hz)
Strobe speed 5 (5 Hz)
Strobe speed 6 max. (6,75 Hz)
Pulse open speed 1 min.
Pulse open speed 2
Pulse open speed 3
Pulse open speed 4 max.
Pulse closed speed 1 min.
Pulse closed speed 2
Pulse closed speed 3
Pulse closed speed 4 max.
Colour and Gobo in black-out
Pan and Tilt in black-out
Open
DMX CHANNEL 8
DMX range
Value
0-27
28-55
56-83
84-111
112-139
140-167
168-195
196-223
224-255
Mid point
DMX value
Parameter: COLOUR
Move
range
(degrees)
IF CHANNEL 9 = FULL COLOUR (Dmx range value 0 - 63)
Mode Option Function
Colour1 (White)
Colour2
Colour3
Colour4
Colour5
Colour6
Colour7
Colour8
Colour9
Page 49
DMX CHANNEL 8
DMX range
Value
Mid point
DMX value
XR300 BEAM
ARC 1200
Parameter: COLOUR
Move
range
(degrees)
49
Mode Option Function
IF CHANNEL 9 = HALF COLOUR (Dmx range value 64 - 127)
0-25
26-51
52-77
78-103
104-129
130-155
156-181
182-207
208-233
234-255
0-10
11-255
0-9
10-127
128-137
138-255
IF CHANNEL 9 = PROPORTIONAL COLOUR (Dmx range value 128 - 191)
IF CHANNEL 9 = RAINBOW (Dmx range value 192 - 255)
Right Rot.Speed from Max to Min
Left Rot.speed from Min to Max
Colour1 (White)
Bicolour ½
Bicolour 2/3
Bicolour 3/4
Bicolour 4/5
Bicolour 5/6
Bicolour 6/7
Bicolour 7/8
Bicolour 8/9
Bicolour 9/1
Colour1 (White)
Proportional colour
No Colour (White)
Stop
DMX CHANNEL 9
DMX CHANNEL 9
DMX CHANNEL 9
DMX range
DMX range
Value
Value
000 - 063
064 - 127
128 - 191
192 - 255
Mid point
Mid point
DMX value
DMX value
Parameter:
Parameter:
Parameter:
Move
Move
range
range
(degrees)
(degrees)
COLOUR MODE
Mode Option Function
Mode Option Function
Full colour
Full colour
Half colour
Half colour
Proportional colour
Rainbow
Rainbow
Page 50
DMX CHANNEL
DMX range
Value
0-25
26-51
52-77
78-103
104-129
130-155
156-181
182-207
208-213
214-219
220-225
226-231
232-237
238-243
244-249
250-255
XR300 BEAM
ARC 1200
10
Mid point
DMX value
Parameter: GOBO
Move
range
(degrees)
50
Mode Option Function
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Rotation speed 1 min.
Rotation speed 2
Rotation speed 3
Rotation speed 4
Rotation speed 5
Rotation speed 6
Rotation speed 7
Rotation speed 8 Max
DMX CHANNEL
DMX range
Value
0-127
128-255
DMX CHANNEL 12
DMX range
Value
0-9
10-127
128-137
138-255
0-255
DMX CHANNEL
11
Mid point
DMX value
Mid point
DMX value
13
Parameter: GOBO MODE
Move
range
(degrees)
Parameter: GOBO ROTATION/GOBO INDEX COARSE
Move
range
(degrees)
Mode Option Function
Gobo Rotation Mode
Gobo Index Mode
Mode Option Function
IF CHANNEL 11 = Gobo Rotation Mode (Dmx range value 0 - 127)
Stop
SX Rot. Prop. Speed Max to Min
Stop
DX Rot. Prop. Speed Min to Max
IF CHANNEL 11 = Gobo Index Mode (Dmx range value 128 - 255)
Parameter: GOBO INDEX FINE
Gobo index Coarse
DMX range
Value
0-255
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Gobo Index Fine
Page 51
DMX CHANNEL
DMX range
Value
0-9
10-22
23-35
36-48
49-61
62-74
75-87
88-100
101-113
114-126
127-138
139-151
152-164
165-177
178-190
191-203
204-216
217-229
230-242
243-255
14
Mid point
DMX value
Parameter: GOBO SHAKE
Move
(degrees)
range
Mode Option Function
51
Stop
Gobo Shake R-L Speed 1 Min.
Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
Gobo Shake R-L Speed 4
Gobo Shake R-L Speed 5
Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7
Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2
Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4
Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
Gobo Shake L-R Speed 9 Max
XR300 BEAM
ARC 1200
DMX CHANNEL
DMX range
Value
000-029
030-245
246-255
DMX CHANNEL 16
DMX range Mid point
Value DMX value
0-9
10-60
61-129
130-179
180-200
201-239
240-255
15
Parameter: FROST
Mid point
DMX value
Parameter: RESET / LAMP
Move
range
(degrees)
Mode Option Function
Move
range
Mode
(degrees)
Option
No function
Linear Frost
Frost fully inserted
Function
No Effect
Lamp OFF (activ.after 3 seconds)
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
Internal motor reset
Total Reset
Page 52
23- 8 MOTORS CONTROL CARD
8 MOTORS CONTROL CARD
J7 Magnetic Sensors
Connector
Line 1 Brown:
Line 2 Orange:
GND
ORANGE
BROWN
VCC
52
XR300 BEAM
ARC 1200
Gobo
(BLACK)
RotGobo
(DARK GREEN)
J1 Internal DATA
Communication
Connector
From J8 Pan & Tilt
card
30 VDC
Strobe
(YELLOW)
Frost
(PINK)
+
Color
(GREY)
-
Magenta
(LIGHT BLUE)
Cyan
(GOLD)
Fans
Yellow
(BLUE)
Fans
Page 53
24-PAN & TILT CARD
ENCODER PAN
(RED)
ENCODER TILT
(ORANGE)
DATA 2
DATA 1
(VIOLET)
(LIGHT GREEN)
(BROWN)
MOTOR TILT
PAN
(WHITE)
53
TILT
(BROWN)
GND
(BLACK)
30 VDC
(RED)
XR300 BEAM
ARC 1200
FAN
(WHITE)
TO J2
LAMP
ON-OFF
CARD
TO J1
DISPLAY CARD
(WHITE)
25-CABLES RESEND CARD
ENCODER TILT
(ORANGE)
26-DISPLAY CARD
27-LAMP ON-OFF CONTROL CARD
8 MOTORS CARD
BLACK RED
TO J1
(VIOLET)
BLACK BLACK
J4
DMX INPUT
(WHITE)
FROM J12
PAN&TILT
CARD
FROM J16
PAN&TILT
CARD
J2
J3
TO J9
ELECTRONIC
BALLAST
Page 54
28- ROTATING GOBO WHEEL
3
2
4
54
5
6
XR300 BEAM
ARC 1200
1
7
GOBO 1 METAL
0516G033.01
GOBO 4 METAL GOBO 5 METAL GOBO 6 METAL
GOBO 2 METAL
0516G033.02
GOBO 3 METAL
0516G033.03
GOBO 7 METAL
0516G033.04
0516G033.05 0516G033.06
0516G033.15.M.58
Page 55
55
29- COLOUR WHEEL
XR300 BEAM FAR E.B. (Cod. 03.MB002.EB.LF) • FAR system • CMY • Electronic ballast
XR300 BEAM FAR (Cod. 03.MB002.LF) • FAR system • CMY • Electromagnetic ballast
XR300 BEAM E.B. (Cod. 03.MB002.EB.L) • CMY • Electronic ballast
XR300 BEAM
ARC 1200
3
COL1
1
2
COL2
8
7
COL3
4
5
6
COL4
0507K005.D01
HALF CTO
HOT TC3256
0507C047.D01
RED LW 640
0507K004.D01
CTO
TC3256
COL6COL5
0507C046.D01
WOOD SW460
0507C053.D01
AMBER LW 550
COL7
0507C042.D01
GREEN WB5055
0507C051.D01
ORANGE LW590
COL8
0507C041.D01
DARK BLUE SW490
Page 56
56
29- COLOUR WHEEL
XR300 BEAM BF (Cod. 03.MB003.L) • Electromagnetic ballast
3
XR300 BEAM
ARC 1200
2
1
8
COL1 COL2
7
COL3
4
5
6
COL4
0507C051.D01
ORANGE LW590
0507C045.D01
CYAN SW 530
0507C049.D01
YELLOW LW 515
COL6COL5
0507C043.D01
LAVANDER SL0064
0507C047.D01
RED LW 640
COL7
0507C042.D01
GREEN WB5055
0507C046.D01
WOOD SW460
COL8
0507C041.D01
DARK BLUE SW490
Page 57
57
30- GOBOS PROVIDED IN THE BOX AS STANDARD ACCESSORIES
XR300 BEAM
ARC 1200
GOBO 8 METAL
0516G033.08 0516G033.09 0516G033.10
GOBO 11 METAL
GOBO 9 METAL GOBO 10 METAL
GOBO 12 METAL
0516G033.11 0516G033.12
Page 58
NOTES
58
XR300 BEAM
ARC 1200
Page 59
NOTES
59
XR300 BEAM
ARC 1200
Page 60
The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its
products without prior notice. D.T.S. assumes no responsibility for the use or application of the
products or circuits described herein.
MADE IN ITALY
*0517I136*
*0517I136*
D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy
Tel. +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it www.dts-lighting.it
Loading...