DTS XR2000 SPOT CMY User Manual

Download

Page 1

XR2000 SPOT CMY

User’s Manual Rel 1.6

D.T.S. Illuminazione srl - ITALY http://www.dts-lighting.it

Made in Italy

Page 2

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

XR2000 SPOT CMY

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

D.T.S.

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

D.T.S.

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

D.T.S.

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

D.T.S.

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S

D.T.S.

Page 3

INDEX:

1- SYMBOLS 4 2- GENERAL WARNING 4 3- GENERAL WARRANTY CONDITION 4 4- TECHNICAL FEATURES 5 5- ACCESSORIES 7 6- IMPORTANT SAFETY INFORMATION 8

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Protection against ultraviolet radiation

6.4 Safety

6.5 Level of protection against the penetration of solid and liquid objects 7- MOUNTING THE LAMP 9

7.1 Lamp alignment 8- VOLTAGE AND FREQUENCY 10 9- INSTALLATION 10

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature 10- MAINS CONNECTION 11

10.1 Protection 11- DMX SIGNAL CONNECTION 12

11.1 DMX Addresses

11.2 Selecting the DMX address 12- FIRMWARE UPDATING 13 13- DISPLAY FUNCTIONS 14 14- ERROR MESSAGES 17 15- HIDDEN MENU 18

15.1 Calibration mode 19 16- PAN & TILT SPEED 20 17- FANS SPEED 18- OPENING THE PROJECTOR HOUSING 21 19- REPLACING GOBOS 20- PERIODIC CLEANING 22

20.1 Lenses and reflectors

20.2 Fans and air passages 21- PERIODIC CONTROLS 22- DMX PROTOCOL 23 23- 8 MOTORS CONTROL CARD 38 24- 8 MOTORS SLAVE CONTROL CARD 39 25- PAN & TILT CARD 40 26- CABLES RESEND CARD 27- DISPLAY CARD 28- LAMP ON-OFF CONTROL CARD 29- ROTATING GOBO WHEEL 41 30- FIXED GOBO WHEEL 42 31- COLOUR WHEEL 1 43

XR2000 SPOT CMY

Page 4

1- SYMBOLS

Graphic symbols used on this manual

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK RISK

XR2000 SPOT CMY

2- GENERAL WARNING

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON INFLAMMABLE SURFACES”

THIS SYMBOL MEANS “RADIATION FROM THIS LAMP CAN CAUSE DAMAGE TO EYES AND SKIN”

THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT

Read the instruction contained in this user manual carefully, as they give important information regarding safety during installation , use and maintenance. The device is not for domestic use and must be installed by a qualified electrician or experienced person. Always disconnect the device from the mains before replacing the lamp. The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating. The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.

Page 5

XR2000 SPOT CMY

4- TECHNICAL FEATURES

The XR2000 SPOT CMY is one of the most powerful moving heads in the 700W range. The XR2000 SPOT CMY in fact delivers a massive 64.300 Lux at 5 m (8° beam angle), thanks to its improved optical group and dichroic glass reflector, combined with a Philips MSR Gold 700/2 Fastfit lamp (50.000 Lumens). The XR2000 SPOT CMY is particularly suitable for all professional applications, both mobile (concerts, shows, tours, special events) and fixed (clubs and other venues), requiring a light with extremely high luminous output and versatility of functions. The XR2000 SPOT CMY is also the ideal light for a vast range of applications in which quiet operation is a priority, thanks to its silent ventilation system and silent pan/tilt operation. The XR2000 SPOT CMY incorporates motorized focus; motorized iris; linear zoom (8°- 30°); a sophisticated CMY colour synthesis system with 3 palettes for linear insertion, plus a colour wheel (7 colours + open); 2 gobo wheels: one customizable rotating gobo wheel (7 gobos) and one customizable fixed gobo wheel (8 gobos); frost filter (soft edge); 3-facet rotating prism; animation wheel rotating in both directions. The 16 bit Pan/Tilt mechanism features an exclusive Super Speed function, and a locking system with recessed buttons. Access to every feature of the internal menu is simple and direct, thanks to the new user interface featuring a LCD backlit graphic display (128 x 64).

XR2000 SPOT CMY (Cod. 03.MS008.EB.L)

• Electronic ballast 90-245V 50/60 Hz • Black finish Also available with white finish (RAL 9003) on demand

Lamp

Lamp: Philips MSR Gold 700/2 Fastfit Automatic switching ON of lamp in case of accidental switching OFF. Lamp ON/OFF via DMX; Reset via DMX.

Optical group

64.300 Lux at 5 m (8° beam angle) Dichroic glass reflector

Focus

Motorized focus

Iris

Motorized iris (16 bit)

Zoom

Motorized zoom (8°- 30°)

Page 6

XR2000 SPOT CMY

4- TECHNICAL FEATURES

Dimmer / shutter / strobo

Linear dimmer Shutter Strobe from 0,85 flash/sec to 6,75 flash/sec Power saving mode (the lamp dims to 50% six seconds after shutter closure)

Colours

CMY colour synthesis system + colour wheel (7 colours + open) with linear selection for perfect 2-colour beams Colour change with blackout sync; rainbow effect

Gobos

2 gobo wheels: 1 rotating (7 indexable 16 bit gobos + open) and 1 fixed (8 gobos + open) Extractable gobo holders for both wheels Gobo change with synchronized blackout Gobo scrolling; Gobo shake

Effects

Indexable prism rotating in both directions (3-facet) Frost filter (soft edge) Animation wheel rotating in both directions

Pan / Tilt

Pan 540° (3,9 sec.); Tilt 270° (2,6 sec.); 16-bit resolution Super Speed function; extremely smooth and precise movements even at the highest speeds Pan / Tilt locking system with recessed buttons Automatic Pan/Tilt repositioning in case of knocks

30 DMX channels (Default)

Internal operating system updatable via DMX

Interface

LCD backlit graphic display (128x64)

Connections

4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik POWERCONN connector by Neutrik

Power supply

Electronic ballast: 90 - 260 V (50/60 Hz) Power consumption: 820 W

Power saving mode (the lamp dims to 50% six seconds after shutter closure)

Standard accessories

2 x “C” GQuick clamps with “fastlock” connection

Thermal

Operating ambient temperature: -10° / 40°

Weight

44,5 Kg

Page 7

4- TECHNICAL FEATURES

Dimensions

XR2000 SPOT CMY

Packaging Dimensions (LxWxH) 670 x 550 x 730 mm Weight: 49,5 Kg

m m

826

568mm

Unit Dimensions (LxWxH) 568x510x826mm Weight: 44,5 Kg

510mm

7 °2

m m

636

5- ACCESSORIES

459mm

As standard

•1 x MSR Gold 700/2 Fastfit lamp

•1 x POWERCONN male cable connector (cod. 0520P014)

•1 x XLR 5 Pins male cable connector (cod. 0508B028)

•1 x XLR 5 Pins female cable connector (cod. 0508B027)

•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• User’s manual

Optional (on request)

• Wireless DMX receiver card (cod. 03.LA.012)

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn (cod. 02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

Page 8

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

XR2000 SPOT CMY

XR2000 SPOT CMY uses a PHILIPS /2

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1.5 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head, including lamp replacement.

-The level of technology inherent in the XR2000 SPOT CMY requires the assistance of specialised personnel for all servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Protection against ultraviolet radiation:

MSR Gold 700 Fastfit lamp

-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged. Their respective shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

6.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

6.5 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid objects is IP 20. For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:

• Raincover for XR2000 base (top) (cod. 03.MA009)

• Raincover for XR2000 base (bottom) (cod. 03.MA010)

Page 9

XR2000 SPOT CMY

7- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

Philips MSR Gold 700/2 Fastfit Power 700W Luminous flux 50,000 lm Colour temperature 7.500°K Lampbase PGJX50 Rated life 750 hours

1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .

Photo 2Photo 1 Photo 4Photo 3

2) Insert the lamp (photo2).

3)Rotate the lamp 1/4 turn clockwise (photo 3 and 4). The lamp used on XR2000 SPOT CMY is made in quartz glass and should be handled with care. Always follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided in the lamp’s packaging. The lamp socket is not symmetrical. DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat the procedure.

4) Replace the metal cover and tighten the screws A,B,C, which were previously removed. WARNING: Never look directly at the lamp when it’s lit. Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.

PGJX50

7.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic filters and other components inside the unit. The lamp alignment is also essential to obtain the maximum unifirmity and luminous performance by the projection.

Lamp

Photo 5

Alignment

Normal Hot Spot

1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the

Z (photo 5)

When the lamp is correctly optimized,

zones wich are brighter than others.

until you achieve a uniform flat field.

you will have an evenly projected light beam, with no shadows or

3 adjusters X, Y and

Page 10

XR2000 SPOT CMY

8- VOLTAGE AND FREQUENCY

The XR2000 SPOT CMY with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

XR2000 SPOT CMY may be either floor or ceiling mounted. For floor mounting installations, the XR2000 SPOT CMY is supplied with four rubber mounting feet on the base. For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface. The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as not to move or shake whilst the XR2000 SPOT CMY is moving. Eight 1/4 turn Fast Locks connections placed in the base of the unit allow to fix the XR2000 SPOT CMY in any position, by using the two Fast Lock “C” clamps provided in the box. .

240 mm

107 mm

9.1- Safety cable

We recommend the use of a safety cable connected to the XR2000 SPOT CMY and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable can bear the weight of the entire unit. You may attach the safety cable to the two holes (A) located on the base of the fixture, as shown in the picture below.

9.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur.

Page 11

XR2000 SPOT CMY

9.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any obstructions in the path of the projector's movement.

270°

WARNING

Do not place any object in the path

of the projector’s movement

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended distance from flammable material is 1 MT.

540°

Minimum distance from the object being illuminated is 2 MT.

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in operation. Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.

10- MAINS CONNECTION

XR2000 SPOT CMY with electronic ballast operate at 90-260 VOLT 50-60 Hz. Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 8 amps at 230V, Or 16 amps at 100-120 V Strict adherence to regulatory norms is strongly recommended.

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR2000 SPOT CMY. A good earth connection is essential for the correct operation of the projector.

Electronic ballast 90-260V 50 / 60Hz

Page 12

XR2000 SPOT CMY

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one. This way, all the projectors are cascade connected. NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

CONTROLLER S TA ND AR D D M X 5 1 2

1=GND 2=DATA3=DATA+

4 2

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX terminator. The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3. The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

120 ohm

OUT

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

PIN 3

PIN 2

Page 13

XR2000 SPOT CMY

11.1-DMX Addresses

XR2000 SPOT CMY can be controlled with 30 (default) or 22 DMX channels. If you want to use the unit in 30 channels mode (default), set the following addresses on the mixer:

Projector 1 A001 Projector 2 A031 If you want to select the next projector, just add “30”

Projector 3 A061 ….. A…. projector 6 A151

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.

TRICKS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.

12 FIRMWARE UPDATING

Warning: This procedure require a base knolewge of computer applications and Windows Hyperterminal program.

To update the software version of the XR2000 SPOT CMY you need: D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008). USB-DMX Driver for the D.T.S. RED BOX interface . (The driver and the installation procedure are available in our web site www.dts-lighting.it)

Updating the software version. Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using Windows Hyperterminal program.

Please refer to an authorised DTS service centre.

It will be possible to download the software from the reserved area of D.T.S. web site: www.dts-lighting.it.

Page 14

XR2000 SPOT CMY

13- DISPLAY FUNCTIONS

DMX OUT

DMX IN

DMX OUT

ENTER

DISPLAY

DOWN

FUSE 16A T 5X20

MAINS

Electronic ballast

90-260V 50 / 60Hz

DISPLAY FUNCTIONS

The XR2000 SPOT CMY display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections. NOTE: the symbol shows which key has to be pushed to obtain the desired function.

PAN DIRECTION This menu allows to set the Pan movement. Normal or Reversed

TILT DIRECTION This menu allows to set the Pan movement. Normal or Reversed

PAN TILT SPEED Pan Tilt Speed control (1-4)

Pan Direction

Up-Down

Tilt Direction

Up-Down

Pan Tilt Speed

Up-Down

Up-DownENTER

PAN DIRECTION

Pan movement Normal or Reversed

ENTER

Default = Normal

NORMAL

MENU ENTER DOWN UP

Up-DownENTER

TILT DIRECTION

Tilt movement Normal or Reversed

ENTER

Default = Normal

NORMAL

MENU ENTER DOWN UP

Up-DownENTER

PAN TILT SPEED

Pan Tilt Speed control

ENTER

Default = 4

MENU ENTER DOWN UP

Page 15

13- DISPLAY FUNCTIONS

XR2000 SPOT CMY

Up-Down

Display

DMX Mode

DISPLAY FLIP / STAND BY / CONTRAST

Display Flip:

Reverses display's reading depending on the mounting position (On the ground or suspended).

Display Standby: To turn off the display (after 5 seconds) Or leave it always on.

Display Contrast: Display contrast regulation (1-16)

DMX MODE To select DMX mode : 30 channels or 22 channels

Up-DownENTER

DISPLAY

FLIP

Display Flip ON THE GROUND (Default) SUSPENDED

ENTER

ON THE GROUND

MENU ENTER DOWN UP

DISPLAY

STANDBY

FLIP

OFF

MENU ENTER DOWN UP

DISPLAY

CONTRAST

FLIP

Display Standby OFF = Display Standby disabled (Default) ON = Display goes OFF after 5 seconds

Display Contrast 1-16 (Default = 8)

ENTER

MENU ENTER DOWN UP

Up-DownENTER

DMX MODE

DMX mode

ENTER

30 channels (Default) 22 channels

30 channels

Up-Down

Lamp

Reset

LAMP Lamp always ON, always OFF, lamp ON-OFF selectable via DMX And lamp life time reset

ADJUST To adjust the lamp with no mixer connected. It’s possible to set the parameters for PAN-TILT and ZOOM

RESET Reset via DMX ENABLED / DISABLED and unit reset

MENU ENTER DOWN UP

Up-DownENTER

LAMP

BY DMX

FLIP

BY DMX = ON / OFF via DMX (default) ALWAYS ON = Forced ON ALWAYS OFF = Forced OFF RESET COUNTER = Lamp life time

ENTER

reset

DOWN

ENTER

LAMP

ADJUST

FLIP

DOWN

ENTER

Up-DownENTER

RESET

BY DMX

ENABLED

LAMP ADJUST = To adjust the lamp

with no mixer connected. It’s possible to set the parameters for PAN-TILT and ZOOM

ENABLED = Reset via DMX enabled (Default) DISABLED = Reset via DMX disabled NOW = Unit motors reset

ENTER

MENU ENTER DOWN UP

Page 16

13- DISPLAY FUNCTIONS

XR2000 SPOT CMY

FAN SPEED Fan Speed control

AUTO FUCOS Automatic focusing

GOBO ROTATION Gobo rotation control the Rotating speed of gobo

Fan Speed

Up-Down

Auto Focus

Up-Down

Gobo Rotation

Up-Down

Up-DownENTER

FAN SPEED

Fan speed control

ENTER

1-5 (Default = 5)

MENU ENTER DOWN UP

Up-DownENTER

AUTO FOCUS

ON OFF = (Default)

ENTER

OFF

MENU ENTER DOWN UP

Up-DownENTER

GOBO ROTATION

During gobo scrolling

ON OFF = (Default)

ENTER

OFF

MENU ENTER DOWN UP

CMY BLACKOUT CMY filters blades inserted at 100% if the dimmer remain closed for more than 5 seconds. By activating this function, it will be possible to reduce substantially any visible light reflection coming out from the front lens when dimmer is closed.

SYSTEM INFO Lamp life time, lamp strikes, unit life time, 8 motors card software version, Pan&Tilt card software version and unit model

RESERVED

Pan lock-Tilt lock Pan free-Tilt free System Reboot (Code = 100)

CMY Blackout

Up-Down

System info

Up-Down

Reserved

Up-Down

Up-DownENTER

CMY BLACKOUT

ON = Blackout enabled (Default)

ENTER

OFF = Blackout disabled

MENU ENTER DOWN UP

Up-DownENTER

SYSTEM INFO

LAMP LIFE:0000H STRIKE:001 UNIT LIFE: 0010H 8M R.20 PT R.19 MODEL: XR2000 BEAM

MENU ENTER DOWN UP

RESERVED

ENTER CODE

000

MENU ENTER DOWN UP

PAN LOCK

MENU ENTER DOWN UP

SYSTEM INFO Lamp life time, lamp strikes, unit life time, 8 motors card software version, Pan&Tilt card software version and unit model

Pan Lock = Lock the Pan to the desired value Tilt Lock = Lock the Tilt to the desired value Pan Free = Remove power to Pan motor Tilt Free = Remove power to Tilt motor System Reboot = Unit Reboot without needing of turning OFF the unit

ENTER

Page 17

13- DISPLAY FUNCTIONS

XR2000 SPOT CMY

Up-Down

Default

Up-DownENTER

DEFAULT To restore main settings

14- ERROR MESSAGES

ERROR

COLOUR WHEEL

MENU ENTER DOWN UP

PRESS ENTER TO CONFORM

MENU ENTER DOWN UP

ERROR

CYAN

DEFAULT

RESTORE MAIN SETTINGS

DEFAULT

RESTORE MAIN SETTINGS

SURE?

PRESS MENU TO CANCEL

MAGENTA

Default To restore main settings

ERROR

ENTER

ERROR

YELLOW

MENU ENTER DOWN UP

COLOUR WHEEL POSITION ERROR

ERROR

PAN

MENU ENTER DOWN UP

PAN REPOSITIONING ENCODER ERROR

ERROR

GOBO

MENU ENTER DOWN UP

CYAN POSITION ERROR MAGENTA POSITION

ERROR

TILT

MENU ENTER DOWN UP

TILT REPOSITIONING ENCODER ERROR

ERROR

GOBO INDEX

MENU ENTER DOWN UP

ERROR

INTERNAL BUS

MENU ENTER DOWN UP

COMMUNICATION PROBLEM BETWEEN 8 MOTORS CARD AND PAN&TILT CARD

ERROR

FIXED GOBO

MENU ENTER DOWN UP

YELLOW POSITION ERROR

ERROR

DMX ADDRESS

MENU ENTER DOWN UP

DMX ADDRESS ERROR

ERROR

ANIMATION

MENU ENTER DOWN UP

GOBO WHEEL ERROR GOBO POSITION

MENU ENTER DOWN UP

ERROR

MENU ENTER DOWN UP

FIXED GOBO WHEEL ERROR

MENU ENTER DOWN UP

ANIMATION WHEEL ERROR

Page 18

XR2000 SPOT CMY

ERROR

IRIS

MENU ENTER DOWN UP

IRIS ERROR

ERROR

ZOOM

MENU ENTER DOWN UP

ZOOM ERROR

ERROR

EFFECT

MENU ENTER DOWN UP

EFFECT WHEEL ERROR

ERROR

DIFFUSER

MENU ENTER DOWN UP

DIFFUSER ERROR

ERROR

FOCUS

MENU ENTER DOWN UP

FOCUS ERROR

15- HIDDEN MENU

For technical personnel only.

To operate this menu:

-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)

- Reset the XR2000 SPOT CMY (reset from the MENU, not from the DMX controller!).

- While reset is running, press the MENU and ENTER keys at the same time.

CALIBRATION

MOTORS ALIGNMENT

PAN

134

MENU ENTER DOWN UP

ELECTRONIC CALIBRATION OF THE MOTORS

MIN LAMP POW.

1=65% 100=100%

DEFAULT CAL

SET ALL MOTORS AT 128

MENU ENTER DOWN UP

RESET EEPROM. RESET ALL SETTINGS TO 128 VALUE

EXIT TO MAIN

FANS SPEED

ONLY AT MIN LAMP POWER

MENU ENTER DOWN UP

FAN SPEED WHEN DIMMER CLOSED

MENU ENTER DOWN UP

LAMP POWER WHEN DIMMER CLOSED

MENU ENTER DOWN UP

EXIT FROM HIDDEN MENU

Page 19

15.1 Calibration

XR2000 SPOT CMY

CALIBRATION

MOTORS ALIGNMENT

PAN

134

MENU ENTER DOWN UP

PAN ALIGNMENT To align Pan position

CALIBRATION

MOTORS ALIGNMENT

COLOUR WHEEL

151

MENU ENTER DOWN UP

COLOUR WHEEL ALIGNMENT To align Colour wheel

CALIBRATION

MOTORS ALIGNMENT

TILT

167

MENU ENTER DOWN UP

TILT ALIGNMENT To align Tilt position

CALIBRATION

MOTORS ALIGNMENT

CYAN ZERO

162

MENU ENTER DOWN UP

CYAN ZERO ALIGNMENT Cyan zero position setting

CALIBRATION

MOTORS ALIGNMENT

SHUTTER

145

MENU ENTER DOWN UP

SHUTTER ALIGNMENT To align Shutter blades

CALIBRATION

MOTORS ALIGNMENT

CYAN PATH

134

MENU ENTER DOWN UP

CYAN PATH ALIGNMENT Cyan excursion setting

CALIBRATION

MOTORS ALIGNMENT

MAGENTA ZERO

167

MENU ENTER DOWN UP

MAGENTA ZERO ALIGNMENT Magenta zero position setting

CALIBRATION

MOTORS ALIGNMENT

YELLOW PATH

121

MENU ENTER DOWN UP

YELLOW PATH ALIGNMENT Yellow excursion setting

CALIBRATION

MOTORS ALIGNMENT

MAGENTA PATH

151

MENU ENTER DOWN UP

MAGENTA PATH ALIGNMENT Magenta excursion setting

CALIBRATION

MOTORS ALIGNMENT

GOBO

151

MENU ENTER DOWN UP

GOBO WHEEL ALIGNMENT To align Gobo wheel

CALIBRATION

MOTORS ALIGNMENT

YELLOW ZERO

141

MENU ENTER DOWN UP

YELLOW ZERO ALIGNMENT Yellow zero position setting

CALIBRATION

MOTORS ALIGNMENT

GOBO INDEX

141

MENU ENTER DOWN UP

GOBO WHEEL INDEX ALIGNMENT To align Gobo wheel Index

CALIBRATION

MOTORS ALIGNMENT

FIXED GOBO

151

MENU ENTER DOWN UP

G O B O F I X E D W H E E L ALIGNMENT To align Gobo wheel

CALIBRATION

MOTORS ALIGNMENT

ANIMATION

151

MENU ENTER DOWN UP

ANIMATION WHELL ALIGNMENT To align ANIMATION WHEEL

CALIBRATION

MOTORS ALIGNMENT

IRIS

MENU ENTER DOWN UP

IRIS ALIGNMENT To align IRIS

Page 20

Calibration mode

XR2000 SPOT CMY

CALIBRATION

MOTORS ALIGNMENT

EFFECTS

MENU ENTER DOWN UP

EFFECTS ALIGNMENT To align EFFECTS

CALIBRATION

MOTORS ALIGNMENT

DIFFUSER

MENU ENTER DOWN UP

DIFFUSER ALIGNMENT To align DIFFUSER

CALIBRATION

MOTORS ALIGNMENT

FOCUS

151

MENU ENTER DOWN UP

FOCUS ALIGNMENT To alignFOCUS

CALIBRATION

MOTORS ALIGNMENT

ZOOM

151

MENU ENTER DOWN UP

ZOOM ALIGNMENT To align ZOOM

16- PAN & TILT SPEED (default: 4)

You can set the PAN and TILT motors at high speed on your XR2000 SPOT CMY. Press menu until you see PAN TILT SPEED. Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER.

17- FAN SPEED ( default: 5)

Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be less than 35° C.

Page 21

XR2000 SPOT CMY

18- OPENING THE PROJECTOR HOUSING

It is possible to inspect the inside of the projector by removing the cover as indicated below.

ATTENTION

REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.

1) Loosen the 3 screws which fix the head covers (photo 1) .

2) Once unscrewed, simply lift the covers to access the internal components (photo 2).

Photo 1

Photo 2

19- REPLACING GOBOS

XR2000 SPOT CMY uses a mechanical system which allows the fixture's gobos to be removed without the use of special tools. Replacement gobos should be made of either heat resistant glass or metal. An ever-increasing range of gobos is available from your DTS sales network. Gobo dimensions are as follows: ø external (ED) = 27.9 mm ø of image with defined edge (ID) = 24 mm thickness = from 0.2 to 4 mm (see catalogue)

Max thickness

4 mm

Coated side

When an object is held up the coated side of the glass gobo there is no space between the object and its reflection.

Uncoated side

When an object is held up the uncoated side of the glass gobo there is a space between the object and its reflection.

Load with coated surface toward the light source.

Coated side

Uncoated side

Page 22

Replacing gobos on the rotating gobo wheel

When replacing gobos, ensure that the projector is switched off.

1) Open the projector housing as described on page 21.

2) Remove the gobo holder to allow easier access to the gobo (photo 1).

3) Release the gobo retaining spring and carefully remove the gobo (photo 2).

4) Reverse the procedure to install a replacement gobo.

XR2000 SPOT CMY

Photo 1

Photo 2

20- PERIODIC CLEANING

20.1- Lenses and reflectors

Even a fine layer of dust can reduce the luminous output substantially. Regularly clean all lenses and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.

20.2- Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. If necessary, clean the fans and air passages more frequently.

21- PERIODIC CONTROLS

Attention

Disconnect mains power prior to removing the projector housing.

Lamp

The lamp should be replaced if there is any visible damage or deformation due to heat. This will help to avoid the danger of the lamp exploding. XR2000 SPOT CMY lamp lifespan is about 750 hours, then it is necessary to replace it.

Mechanical parts

Periodically check all mechanical parts,gears, guides, belts, etc.for wear and tear, replacing them if necessary. Periodically check the lubrication of all components, particularly the parts subject to high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S. distributor. Check the tension of the belts and adjust it if necessary.

Electrical components

Check all electrical components for correct earthing and proper connection of all connectors, refastening if necessary.

Fuse replacement

Locate the fuse, which protects the lamp and electronics, in the base of the XR2000 SPOT CMY Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.

Page 23

22- DMX PROTOCOL

30 CHANNELS MODE (DEFAULT)

1 PAN msb 540°

2 PAN lsb 3 TILT msb 270° 4 TILT lsb 5 SPEED MOVEMENT 6 DIMMER 7 SHUTTER 8 COLOUR 9 COLOUR MODE 10 CYAN 11 MAGENTA 12 YELLOW 13 SPEED CMY 14 MACRO CMY 15 GOBO 16 GOBO MODE 17 GOBO ROTATION/INDEX 18 GOBO INDEX FINE 19 GOBO SHAKE 20 FIXED GOBO 21 FIXED GOBO ROTATION 22 ANIMATION 23 ANIMATION ROTATION 24 IRIS 25 IRIS MACRO 26 EFFECT 27 EFFECTS ROTATION 28 FOCUS 29 ZOOM 30 RESET/LAMP

XR2000 SPOT CMY

DMX CHANNEL

DMX range

Value

000-010 011-025

026-127

128-247

248-255

Mid point

DMX value

Parameter: PAN msb

Parameter: PAN lsb

Parameter: TILT msb

Parameter: TILT lsb

Parameter: SPEED MOVEMENT

Move

range

(degrees)

Mode Option Function

Standard

Fast movement

Vector mode from fast to slow

Variable time reaction to

DMX signal ( fast to slow)

Silent Mode

Page 24

DMX CHANNEL 6

DMX range

Value

Mid point

DMX value

Parameter: DIMMER

Move range

(degrees)

Mode Option Function

000-007

008-255

DMX CHANNEL

DMX range

Value

000-019 020-039

040-059 060-079 080-089 090-099

100-109

110-119 120-129

130-139 140-149 150-159 160-169

170-179 180-189

190-199

200-209

210-219

220-227

228-233

234-255

Mid point

DMX value

Parameter: SHUTTER

Move

range

(degrees)

Mode Option Function

Proportional dimmer

Open

Random Strobe

Strobe speed 1 min. (0,85 Hz)

Strobe speed 2 (1,4 Hz) Strobe speed 3 (2 HZ) Strobe speed 4 (3,75 Hz) Strobe speed 5 (5 Hz)

Strobe speed 6 max. (6,75 Hz)

Pulse open speed 1 min.

Pulse open speed 2 Pulse open speed 3

Pulse open speed 4 max.

Pulse closed speed 1 min.

Pulse closed speed 2 Pulse closed speed 3

Pulse closed speed 4 max.

Colour and Gobo in black-out

Pan and Tilt in black-out

XR2000 SPOT CMY

Black-out

Open

DMX CHANNEL 8

DMX range

Value

000-031

032-063

064-095

096-127

128-159 160-191 192-223

224-255

Mid point

DMX value

Parameter: COLOUR

Move

range

(degrees)

Mode Option Function

Colour 1 Colour 2 Colour 3 Colour 4 Colour 5 Colour 6 Colour 7 Colour 8

Page 25

DMX CHANNEL 8

DMX range

Value

Mid point

DMX value

XR2000 SPOT CMY

Parameter: COLOUR

Move

range

(degrees)

Mode Option Function

IF CHANNEL 9 = HALF COLOUR (DMX range value 64 - 127)

000-027

028-055

056-083

084-111

112-139 140-167 168-195 196-223

224-255

000-010

011-255

000-009

010-127 128-137 138-255

IF CHANNEL 9 = PROPORTIONAL COLOUR (DMX range value 128 - 191)

IF CHANNEL 9 = PROPOTIONALL RAINBOW (DMX range value 192 - 255)

CW Rot.Speed from Max to Min

CCW Rot.speed from Min to Max

Colour 1

Bicolour 1/ 2 Bicolour 2/ 3 Bicolour 3/ 4 Bicolour 4/ 5

Bicolour 5/ 6 Bicolour 6/ 7 Bicolour 7/ 8 Bicolour 8/ 1

No Colour

Proportional colour

No Colour

Stop

DMX CHANNEL 9

DMX range

Value

000-063 064-127

128-191

192-255

DMX CHANNEL 10

DMX range

Value

000-255

DMX CHANNEL 11

Mid point

DMX value

Mid point

DMX value

Parameter: COLOUR MODE

Move

range

(degrees)

Parameter: CYAN

Move

range

(degrees)

Parameter: MAGENTA

Mode Option Function

Full Colour Half Colour

Proportional Colour Propotional Rainbow

Propotional colour

DMX range

Value

000-255

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

Propotional colour

Page 26

DMX CHANNEL 12

DMX range Mid point

Value DMX value

000-255

Parameter: YELLOW

Move

range

(degrees)

XR2000 SPOT CMY

Mode Option Function

Propotional colour

DMX CHANNEL 13

DMX range Mid point

Value DMX value

000-007 008-255

DMX CHANNEL

DMX range Mid point

Value DMX value

000-009 010-014 015-019 020-024

025-029 030-034

035-039 040-044 045-049

050-054 055-059 060-064 065-069 070-074 075-079 080-084 085-089

090-094 095-099 100-104 105-109 110-114 115-121 122-128

129-135 136-142

143-149 150-156 157-163

164-170

Parameter:

Parameter: MACRO CMY

SPEED CMY

Move

range Mode Option Function

(degrees)

Move

range Mode Option Function

(degrees)

No function

Variable speed from max to min

No function

Macro1

Macro2

Macro3 Macro4 Macro5

Macro6

Macro7

Macro8 Macro9

Macro10 Macro11

Macro12

Macro13

Macro14

Macro15

Macro16

Macro17

Macro18 Macro19

Macro20 Macro21

Macro rainbow wait=0 Macro rainbow wait=2

Macro rainbow wait=3 Macro rainbow wait=4

Macro rainbow wait=5 Macro rainbow wait=6

Macro rainbow wait=7 Macro rainbow wait=8

Page 27

DMX CHANNEL

DMX range Mid point

Value DMX value

171-177 178-185 186-192 193-199 200-206 207-213

214-220 221-227 228-234

228-234

228-234 235-241

235-241

235-241 242-248 249-255

DMX CHANNEL

Parameter: MACRO CMY

Move

range

(degrees)

Parameter: GOBO 1

Mode Option Function

XR2000 SPOT CMY

Macro rainbow wait=9 Macro rainbow wait=10

Full colours rainbow wait=0 Full colours rainbow wait=2

Full colours rainbow wait=3

Full colours rainbow wait=4

Full colours rainbow wait=5

Full colours rainbow wait=6

Full colours rainbow wait=7

Full colours rainbow wait=8 Full colours rainbow wait=9 Full colours rainbow wait=10

DMX range Mid point

Value DMX value

000-025 026-051 052-077

078-103

104-129 130-155

156-181

Move

range Mode Option Function

(degrees)

182-207

208-213

214-219 220-225 226-231 232-237 238-243 244-249 250-255

Open Gobo 1

Gobo 2

Gobo 3

Gobo 4 Gobo 5 Gobo 6

Gobo 7

Speed rotation 1 min.

Speed rotation 2 Speed rotation 3

Speed rotation 4 Speed rotation 5 Speed rotation 6

Speed rotation 7 Speed rotation 8 max

DMX CHANNEL 16

DMX range Mid point

Value DMX value

000-127

128-255

Parameter: GOBO MODE

Move

range Mode Option Function

(degrees)

Gobo rotation mode Gobo index mode

Page 28

DMX CHANNEL 17

DMX range Mid point

Value DMX value

Parameter: GOBO 1 ROTATION/GOBO 1 INDEX COARSE

Move

range Mode Option Function

(degrees)

XR2000 SPOT CMY

IF CHANNEL 16 = Gobo Rotation Mode (Dmx range value 0 - 127)

000-009 010-127 128-137 138-255

000-255

DMX CHANNEL

DMX range Mid point

Value DMX value

000-255

DMX CHANNEL

DMX range

Value

000-009 010-022

023-035

036-048 049-061

062-074 075-087 088-100

101-113 114-126

127-138 139-151 152-164

165-177

178-190 191-203

204-216 217-229 230-242 243-255

Mid point

DMX value

CCW Rot. Prop. Speed Max to Min

CW Rot. Prop. Speed Min to Max

Stop

IF CHANNEL 16 = Gobo Index Mode (Dmx range value 128 - 255)

Parameter: GOBO 1 INDEX FINE

Move

range

(degrees)

Parameter: GOBO 1 SHAKE

Move

range

(degrees)

Mode Option Function

Gobo Shake R-L Speed 1 Min. Gobo Shake R-L Speed 2

Gobo Shake R-L Speed 3

Gobo Shake R-L Speed 4 Gobo Shake R-L Speed 5 Gobo Shake R-L Speed 6

Gobo Shake R-L Speed 7 Gobo Shake R-L Speed 8 Gobo Shake R-L Speed 9 Max

Gobo Shake L-R Speed 1 Min Gobo Shake L-R Speed 2

Gobo Shake L-R Speed 3 Gobo Shake L-R Speed 4 Gobo Shake L-R Speed 5 Gobo Shake L-R Speed 6 Gobo Shake L-R Speed 7

Gobo Shake L-R Speed 8 Gobo Shake L-R Speed 9 Max

Gobo index Coarse

Gobo Index Fine

Stop

Page 29

DMX CHANNEL

DMX range Mid point

Value DMX value

000-022 Open 023-045

046-068 069-091

092-114 115-137 138-160 Gobo 6

161-183 184-207 208-213 214-219

220-225 226-231 232-237 238-243 244-255

Parameter:

FIXED GOBO

Move range Mode Option Function

(degrees)

Speed rotation Speed rotation Speed rotation 3

Speed rotation 4 Speed rotation 5

Speed rotation 6 Speed rotation 7 max

XR2000 SPOT CMY

Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5

Gobo 7 Gobo 8

1 min 2

DMX CHANNEL

DMX range

Value

000-009 010-022

023-035

036-048 049-061

062-074 075-087 088-100

101-113 114-126

127-138 139-151 152-164

165-177

178-190 191-203

204-216 217-229 230-242 243-255

Mid point

DMX value

Parameter: FIXED GOBO SHAKE

Move

range

(degrees)

Mode Option Function

Stop Gobo Shake R-L Speed 1 Min. Gobo Shake R-L Speed 2

Gobo Shake R-L Speed 3

Gobo Shake R-L Speed 4 Gobo Shake R-L Speed 5 Gobo Shake R-L Speed 6

Gobo Shake R-L Speed 7 Gobo Shake R-L Speed 8 Gobo Shake R-L Speed 9 Max

Stop Gobo Shake L-R Speed 1 Min Gobo Shake L-R Speed 2

Gobo Shake L-R Speed 3 Gobo Shake L-R Speed 4 Gobo Shake L-R Speed 5 Gobo Shake L-R Speed 6 Gobo Shake L-R Speed 7

Gobo Shake L-R Speed 8 Gobo Shake L-R Speed 9 Max

Page 30

DMX CHANNEL 22

DMX range Mid point

Value DMX value

000-009

010-255

DMX CHANNEL

DMX range Mid point

Value DMX value

000-009 010-127

128-137

138-255

Parameter: ANIMATION

Move range Mode Option Function

(degrees)

Parameter:

ANIMATION ROTATION

Move

range Mode Option Function

(degrees)

No function

Linear animation position

XR2000 SPOT CMY

Stop

CCW rotation from fast to slow

Stop

CW rotation from fast to slow

DMX CHANNEL 24

DMX CHANNEL 25

DMX range Mid point

Value DMX value

000-009 010-246

247-255

DMX range Mid point

Value DMX value

000-009 010-063 064-117

064-117

118-171

172-213

214-255

Parameter:

IRIS

Move

range Mode Option Function

(degrees)

Open

Linear Iris from Open to ClosedLinear Iris from Open to Closed

Closed

IRIS MACROS

Move

range Mode Option Function

(degrees)

Iris pulse with flash closing combined with zoom from Min to Max Iris pulse with flash opening combined with zoom from Min to Max

Iris pulse at different speed from Min to Max

Iris pulse with flash closing from Min to Max

Iris pulse with flash opening from Min to Max

No effect

DMX CHANNEL 26

DMX range

Value

000-050 051-085

086-171 172-255

Mid point

DMX value

Parameter: EFFECTS

Move

range

(degrees)

Mode Option Function

No effect

Diffuser

Prism

Frost

Page 31

DMX CHANNEL 27

DMX range

Value

000-009

010-127

128-143

Mid point

DMX value

144-255

DMX CHANNEL 28

DMX range

Value

000-255

DMX CHANNEL

DMX range

Value

000-255

Mid point

DMX value

Mid point

DMX value

Parameter: EFFECTS ROTATION

Move

range

(degrees)

Parameter: FOCUS

Move range

(degrees)

Parameter: ZOOM

Move range

(degrees)

Mode Option Function

XR2000 SPOT CMY

Stop

CCW Rotation from fast to slow

Stop

CW Rotation from slow to fast

Linear focus ( 1m to - )

Linear zoom from 8° to 30°

DMX CHANNEL 30

DMX range

Value

000-009 010-060 061-129 130-179

180-200

201-239 240-255

Mid point

DMX value

Parameter: RESET

Move

range

(degrees)

Mode Option Function

No Effect

Lamp OFF (activ.after 3 seconds)

No Effect

Lamp ON (activ.after 3 seconds)

No Effect

Internal motor reset

Total Reset

Page 32

22 CHANNELS MODE

1 PAN msb 540° 2 PAN lsb 3 TILT msb 270° 4 TILT lsb 5 SPEED MOVEMENT 6 DIMMER 7 SHUTTER 8 COLOUR 9 CYAN 10 MAGENTA 11 YELLOW 12 GOBO 13 GOBO ROTATION/INDEX 14 FIXED GOBO 15 ANIMATION 16 ANIMATION ROTATION 17 IRIS 18 EFFECTS 19 EFFECTS ROTATION 20 FOCUS 21 ZOOM 22 LAMP ON/OFF - RESET

XR2000 SPOT CMY

DMX CHANNEL

DMX range

Value

000-010 011-025

026-127

128-247

248-255

Mid point

DMX value

Parameter: PAN msb

Parameter: PAN lsb

Parameter: TILT msb

Parameter: TILT lsb

Parameter: SPEED MOVEMENT

Move

range

(degrees)

Mode Option Function

Standard

Fast movement

Vector mode from fast to slow

Variable time reaction to

DMX signal ( fast to slow)

Silent Mode

Page 33

XR2000 SPOT CMY

DMX CHANNEL 6

DMX range

Value

Mid point

DMX value

000-007 008-255

DMX CHANNEL

DMX range

Value

0-19

20-39 40-59

60-79 80-89

90-99

100-109

Mid point

DMX value

110-119 120-129

130-139 140-149 150-159 160-169 170-179 180-189 190-199 200-209 210-219 220-227 228-233 234-255

DMX CHANNEL 8

Parameter: DIMMER

Move

range

(degrees)

Parameter: SHUTTER

Move

range

(degrees)

Parameter: COLOUR 1

Mode Option Function

Black-out

Proportional dimmer

Mode Option Function

Black-out

Open

Black-out

Random Strobe

Strobe speed 1 min. (0,85 Hz)

Strobe speed 2 (1,4 Hz) Strobe speed 3 (2 HZ) Strobe speed 4 (3,75 Hz) Strobe speed 5 (5 Hz)

Strobe speed 6 max. (6,75 Hz)

Pulse open speed 1 min.

Pulse open speed 2 Pulse open speed 3

Pulse open speed 4 max.

Pulse closed speed 1 min.

Pulse closed speed 2 Pulse closed speed 3

Pulse closed speed 4 max.

Colour and Gobo in black-out

Pan and Tilt in black-out

Open

DMX range

Value

000-011 012-023

024-035 036-047 048-059 060-071

072-083 084-095

096-107 108-119 120-131

132-143

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

Colour 1 Colour 1-2 Colour 2 Colour 2-3 Colour 3 Colour 3-4

Colour 4 Colour 4-5

Colour 5 Colour 5-6

Colour 6 Colour 6-7

Page 34

DMX CHANNEL 8

DMX range

Value

144-155

156-167

168-179

180-197

198-200

201-203

204-206

207-209

210-212

213-215

216-218

219-221

222-224

225-228

229-231

232-234

235-237

238-240

241-243

244246

247-249

250-252

253-255 CCW rotation speed 9 max.

Mid point

DMX value

Parameter: COLOR

Move

range

(degrees)

Mode Option Function

CW rotation speed 9 max.

CW rotation speed 8 CW rotat ion speed 7 CW rotation speed 6 CW rotation speed 5 CW rotation speed 4 CW rotation speed 3 CW rotation speed 2

CW rotation speed 1 min.

CCW rotation speed 1 min.

CCW rotation speed 2 CCW rotation speed 3 CCW rotation speed 4 CCW rotation speed 5 CCW rotation speed 6 CCW rotation speed 7 CCW rotation speed 8

XR2000 SPOT CMY

Colour 7 Colour 7-8 Colour 8 Colour 8-1

Stop

DMX CHANNEL 9

DMX range

Value

000-255

DMX CHANNEL 10

DMX range

Value

000-255

DMX CHANNEL 11

DMX range

Value

000-255

Mid point

DMX value

Mid point

DMX value

Mid point

DMX value

Parameter: CYAN

Move

range

(degrees)

Parameter: MAGENTA

Move

range

(degrees)

Parameter: YELLOW

Move

range

(degrees)

Mode Option Function

Propotional colour

Page 35

DMX CHANNEL

DMX range Mid point

Value DMX value

000-025

026-051

052-077

078-103 104-129

130-155 156-181

Parameter: GOBO

(degrees)

Move

range Mode Option Function

182-207

208-213

214-219

220-225

226-231

232-237

238-243

244-249

250-255

DMX CHANNEL 13

Parameter: GOBO ROTATION/GOBO 1 INDEX COARSE

XR2000 SPOT CMY

Open Gobo 1

Gobo 2

Gobo 3

Gobo 4 Gobo 5 Gobo 6

Gobo 7

Speed rotation 1 min.

Speed rotation 2 Speed rotation 3

Speed rotation 4 Speed rotation 5 Speed rotation 6

Speed rotation 7 Speed rotation 8 max

DMX range Mid point

Value DMX value

000-127

128-180

181-202

203-255

DMX CHANNEL

DMX range Mid point

Value DMX value

000-022 Open

023-045

046-068

069-091

092-114 115-037 138-160 Gobo 6

161-183

184-207

208-213

214-219

Parameter:

220-225

226-231

232-237

238-243

244-255

Move

range Mode Option Function

(degrees)

CCW Rot. Prop. Speed Max to Min

CW Rot. Prop. Speed Min to Max

Stop

FIXED GOBO

Move range Mode Option Function

(degrees)

Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5

Gobo 7

Gobo 8 Speed rotation Speed rotation Speed rotation 3 Speed rotation 4

Speed rotation 5 Speed rotation 6 Speed rotation 7 max

1 min 2

Page 36

DMX CHANNEL 15

DMX range Mid point

Value DMX value

000-009

010-255

DMX CHANNEL

DMX range Mid point

Value DMX value

000-009 010-127

128-137

138-255

Parameter: ANIMATION

Move range Mode Option Function

(degrees)

Parameter:

ANIMATION ROTATION

Move

range Mode Option Function

(degrees)

XR2000 SPOT CMY

No function

Linear animation position

Stop

CCW rotation from fast to slow

Stop

CW rotation from fast to slow

DMX CHANNEL 17

DMX range Mid point

Value DMX value

000-009 010-124

125-132 133-159

160-186

187-213 214-234

235-255

DMX CHANNEL 18

DMX range

Value

000-050 051-085

086-171 172-255

DMX CHANNEL 19

DMX range

Value

000-009

010-127

128-143

Mid point

DMX value

Mid point

DMX value

144-255

Parameter:

Parameter: EFFECTS

Parameter: EFFECTS ROTATION

IRIS

Move

range Mode Option Function

(degrees)

Iris pulse with flash closing combined with zoom from Min to Max Iris pulse with flash opening combined with zoom from Min to Max

Move

range

(degrees)

Move

range

(degrees)

Iris pulse at different speed from Min to Max

Iris pulse with flash closing from Min to Max

Iris pulse with flash opening from Min to Max

Mode Option Function

Linear Iris from Open to Closed

CCW Rotation from fast to slow

Open

Closed

No effect

Diffuser

Prism

Stop

Frost

CW Rotation from slow to fast

Page 37

DMX CHANNEL 20

DMX range

Value

Mid point

DMX value

000-255

DMX CHANNEL

DMX range

Value

000-255

Mid point

DMX value

Parameter: FOCUS

Move range

(degrees)

Parameter: ZOOM

Move range

(degrees)

XR2000 SPOT CMY

Mode Option Function

Linear focus ( 1m to - )

Mode Option Function

Linear zoom from 8° to 30°

DMX CHANNEL 22

DMX range

Value

000-009 010-060 061-129 130-179 180-200 201-239 240-255

Mid point

DMX value

Parameter: RESET / LAMP

Move

range

Mode Option Function

(degrees)

No Effect

Lamp OFF (activ.after 3 seconds)

No Effect

Lamp ON (activ.after 3 seconds)

No Effect

Internal motor reset

Total Reset

Page 38

23- 8 MOTORS CONTROL CARD

8 MOTORS CONTROL CARD

J7 Magnetic Sensors Connector

Line 1 Brown Line 2 Orange

GND ORANGE BROWN VCC

XR2000 SPOT CMY

Rotating gobo wheel

(BLACK)

Fixed gobo wheel

(DARK GREEN)

J26 to 6 Motors

Control card

J9 from J3 Lamp ON-OFF control card

J1 Internal DATA Communication Connector From J8 Pan & Tilt card

30 VDC

Strobe

(YELLOW)

Animation

(PINK)

Colour

(GREY)

Magenta

(LIGHT BLUE)

Fans

Cyan

(Gold)

Yellow

(LIGHT BLUE)

Fans

Page 39

24- 8 MOTORS SLAVE CONTROL CARD

XR2000 SPOT CMY

J1 from 8 Motors

Control card

Rot Animation

(YELLOW LINE)

Diffuser

(VIOLET LINE)

Iris

(RED)

Effect rotation

(DARK ORANGE)

30 VDC

Effects

(LIGHT ORANGE)

Gobo rotation

(BROWN)

Zoom

(YELLOW)

Focus

(VIOLET)

Page 40

25-PAN & TILT CARD

ENCODER PAN

(RED)

ENCODER TILT

(ORANGE)

PAN

(WHITE)

TILT

(BROWN)

GND

(BLACK)

30 VDC

(RED)

XR2000 SPOT CMY

FAN

(WHITE)

TO J2

LAMP

ON-OFF

CARD

DATA 2

DATA 1

(VIOLET)

(LIGHT GREEN)

(BROWN)

MOTOR TILT

TO J1

DISPLAY CARD

(WHITE)

26-CABLES RESEND CARD

(ORANGE)

ENCODER TILT

28-LAMP ON-OFF CONTROL CARD

TO J1

8 MOTORS CARD

(GREEN)

27-DISPLAY CARD

DMX INPUT

(WHITE)

FROM J16 PAN&TILT CARD

TO J9 ELECTRONIC BALLAST

Page 41

29- ROTATING GOBO WHEEL

XR2000 SPOT CMY

GOBO 1 DICRO

0516G032.01

GOBO 4 DICRO GOBO 5 DICRO GOBO 6 DICRO

GOBO 2 DICRO

0516G032.08

GOBO 3 DICRO

0516G032.12

GOBO 7 DICRO

0516G032.10

0516G032.11 0516G032.03

0516G032.05

Page 42

30- FIXED GOBO WHEEL

XR2000 SPOT CMY

GOBO 1 DICRO

0516G032.06

GOBO 2 DICRO GOBO 3 METAL GOBO 4 DICRO

0516G032.04 0516G032.15.M.58 0516G032.07

GOBO 5 GLASS

0516G032.14

GOBO 6 DICRO

0516G032.09

GOBO 7 DICRO GOBO 8 DICRO

0516G032.13

0516G032.02

Page 43

31- COLOUR WHEEL

XR2000 SPOT CMY

COL 1

0507K004.D10 CONV.FILTER HOT TC3256

COL 5

COL 2

0507C046.D10 WOOD SW460

COL 3

0507C051.D10 ORANGE LW590

COL 6

COL 4

0507C042.D10 GREEN WB5055

COL 7

0507C047.D10 RED LW 640

0507C041.D10 DARK BLUE SW490

0507C053.D10 AMBER LW550

Page 44

NOTES

XR2000 SPOT CMY

ARC 1200

Page 45

NOTES

XR2000 SPOT CMY

ARC 1200

Page 46

NOTES

XR2000 SPOT CMY

ARC 1200

Page 47

NOTES

XR2000 SPOT CMY

ARC 1200

Page 48

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.

MADE IN ITALY

*0517I108*

D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy

Tel. +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it www.dts-lighting.it