DTS XR1200 WASH PC User Manual

Download

Page 1

XR1200 WASH

03.MW005.EB.L

XR1200 WASH FRESNEL

User’s Manual Rel 3.0

03.MW005.EB.PC.L XR1200 WASH PC

D.T.S. Illuminazione srl - ITALY http://www.dts-lighting.it

Made in Italy

Page 2

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S.

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

XR1200 WASH

ARC 1200

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de D.T.S. D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

Page 3

XR1200 WASH

ARC 1200

INDEX:

1- SYMBOLS 4 2- GENERAL WARNING 4 3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- ACCESSORIES 6

6- IMPORTANT SAFETY INFORMATION 7

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Protection against ultraviolet radiation

6.4 Safety

6.5 Level of protection against the penetration of solid and liquid matter

7- MOUNTING THE LAMP 8

3.1 Lamp alignment

8- VOLTAGE AND FREQUENCY 9 9- INSTALLATION 9

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement 10

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION 10

10.1 Protection

11- DMX SIGNAL CONNECTION 11

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING 12 13- DISPLAY FUNCTIONS 13 14- ERROR MESSAGES 16

15- HIDDEN MENU 17 16- OPENING THE PROJECTOR HOUSING 18 17- PERIODIC CLEANING

17.1 Lenses and reflectors

17.2 Fans and air passages

18- PERIODIC CONTROLS 19- DMX PROTOCOLS 19 20-COLOUR WHEEL 24 21- 8 MOTORS CONTROL CARD 25 22- PAN & TILT CARD 26 23-CABLES RESEND CARD 24-DISPLAY CARD 25- LAMP ON-OFF CONTROL CARD

Page 4

1- SYMBOLS

Graphic symbols used on this manual

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK RISK

XR1200 WASH

ARC 1200

2- GENERAL WARNING

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON INFLAMMABLE SURFACES”

THIS SYMBOL MEANS “RADIATION FROM THIS LAMP CAN CAUSE DAMAGE TO EYES AND SKIN”

THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT

Read the instruction contained in this user manual carefully, as they give important information regarding safety during installation , use and maintenance. The device is not for domestic use and must be installed by a qualified electrician or experienced person. Always disconnect the device from the mains before replacing the lamp. The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating. The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing material defects.

Page 5

XR1200 WASH

ARC 1200

4- TECHNICAL FEATURES

The XR1200 WASH is a moving head fitted with a Philips MSR Gold 1200W Fastfit discharge lamp (95.000 Lumens) combined with a dichroic parabolic reflector. The XR1200 WASH incorporates motorized zoom (20°- 45° FRESNEL LENS MODEL / 9°-19° PC LENS MODEL), rotating indexable beam shaper (0°-180°), frost filter, CMY colour generation system, colour wheel with linear selection for perfect 2-colour beams (6 dichroic filters + 2 colour conversion filters

3.200°K and 5.600°K +open) and electronic ballast. The XR1200 WASH also includes a new Pan / Tilt locking system with recessed buttons. The XR1200 WASH is particularly suitable for all professional applications, both mobile (concerts, shows, tours, special events) and fixed (clubs and other venues), requiring a light with extremely luminous output capable of illuminating objects and large backgrounds with an endless variety of colours.

XR 1200 WASH FRESNEL (Cod. 03.MW005.EB.L) XR 1200 WASH PC (Cod. 03.MW005.EB.PC.L)

Electronic ballast 90-260V 50/60 Hz• Black colour All models are also available in white colour

Lamp

Lamp: Philips MSR Gold 1200 Fastfit . Automatic switching on of lamp in case of accidental switching off Lamp on/off via DMX; reset via DMX.

Optical group

XR 1200 WASH FRESNEL: XR 1200 WASH PC: 104 9

Borosilicate dichroic parabolic reflector

Zoom

XR 1200 WASH FRESNEL: XR 1200 WASH PC: 9

Dimmer / shutter / strobo

Linear dimmer, Shutter, Strobe from 0,85 flash/sec to 10 flash/sec Power saving mode (the lamp dims to 50% six seconds after shutter closure)

Colours

CMY color generation system with 3 palettes + colour wheel (6 colours + 2 colour conversion filters + open) with linear selection for perfect 2-colour beams. Color change with blackout sync

Effects

Rotating and indexable beam shaper (0°-180°)

Pan / Tilt

Pan 540° (2,9 sec.). Tilt 270° (1,8 sec.). 16-bit resolution 8 selectable speed ranges (8 selectable pan/tilt speeds); extremely smooth and precise movements even at the highest speeds. Pan / Tilt locking system with recessed buttons. Automatic Pan/Tilt repositioning in case of knocks

16 DMX channels

Internal operating system updatable via DMX

INTERFACE

LCD backlit graphic display (128x64)

Connections

4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik

Power supply

Electronic ballast: 90 - 260 V (50/60 Hz); power consumption: 1320 W

Thermal

Operating ambient temperature: -10° / 40°

Weight

38 Kg (Electronic Ballast)

Motorized zoom ( °- 19°)

27.000 Lux at 5 m (20°). Fresnel lens Ø 200 mm.

.000 Lux at 5 m ( °). PC lens Ø 150 mm.

Motorized zoom (20°- 45°)

Page 6

4- TECHNICAL FEATURES

Dimensions

XR1200 WASH

ARC 1200

Packaging Dimensions (LxWxH) 580 x 490 x 800 mm Weight: 43 Kg

m m

85 6

430 mm

Unit Dimensions (LxWxH) 500 x 490 x 685mm Weight: 38 Kg

270°

0 m 4 6

500 mm

490 mm

460 mm

5- ACCESSORIES

As standard

•1 x MSR Gold 1200 Fastfit lamp

•1 x POWERCONN male cable connector (cod. 0520P014)

•1 x XLR 5 Pins male cable connector (cod. 0508B028)

•1 x XLR 5 Pins female cable connector (cod. 0508B027)

•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

•1 x FROST filter (cod. 0506V016 )

• User’s manual

Optional (on request)

• Wireless DMX receiver card (cod. 03.LA.012)

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn (cod. 02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

Page 7

XR1200 WASH

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

XR1200 WASH uses a Philips MSR Gold 1200 Fastfit lamp.

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head, including lamp replacement.

-The level of technology present in the XR1200 requires the assistance of specialised personnel for all servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

6.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

6.5 Level of protection against the penetration of solid and liquid matter:

-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid matter is IP 20. For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:

• Raincover for XR1200 base (top) (cod. 03.MA009)

• Raincover for XR1200 base (bottom) (cod. 03.MA010)

Page 8

XR1200 WASH

7- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

Philips MSR Gold 1200 Fastfit Power 1200W Luminous flux 95,000 lm Colour temperature 6.300°K Lampbase PGJX50 Rated life 750 hours

1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .

Photo 2Photo 1 Photo 4Photo 3

2) Insert the lamp (photo2).

3)Rotate the lamp 1/4 turn clockwise (photo 3 and 4). The lamp used on XR1200 is made in quartz glass and should be handled with care. Always follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided in the lamp's packaging. The lamp socket is not symmetrical. DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat the procedure.

4) Replace the metal cover and tighten the screws A,B,C, which where previously removed. WARNING: Never look directly at the lamp when it’s lit. Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.

PGJX50

7.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic filters and other components inside the unit. The lamp alignment is also essential to obtain the maximum unifirmity and luminous performance by the projection.

Lamp

Alignment

Photo 5

Normal Hot Spot

1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the

Z (photo 5)

When the lamp is correctly optimized,

zones wich are brighter than others.

until you achieve a uniform flat field.

you will have an evenly projected light beam, with no shadows or

3 adjusters X, Y and

Page 9

XR1200 WASH

8- VOLTAGE AND FREQUENCY

The XR1200 with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

XR1200 may be either floor or ceiling mounted. For floor mounting installations, the XR1200 is supplied with four rubber mounting feet on the base. For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface. The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to move or shake whilst the XR1200 is moving. Eight quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps provided in the box, to fix the unit in any position. .

9.1- Safety cable

We recommend the use of a safety cable or chain connected to the XR1200 and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable or chain can bear the weight of the entire unit. You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the picture below.

9.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur.

Page 10

XR1200 WASH

9.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any obstructions in the path of the projector's movement.

270°

WARNING

Do not place any object in the path

of the projector’s movement

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended distance from flammable material is 1 MT.

540°

Minimum distance from the object being illuminated is 2 MT.

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in operation. Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.

10- MAINS CONNECTION

XR1200 with electronic ballast operate at 90-260 VOLT 50-60 Hz. Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 8 amps at 230V, Or 16 amps at 100-120 V Strict adherence to regulatory norms is strongly recommended.

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR1200. A good earth connection is essential for the correct operation of the projector.

Electronic ballast 90-260V 50 / 60Hz

Page 11

XR1200 WASH

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a CANNON XLR 5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one. In this way, all the projectors are cascade connected. NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

CONTROLLER S TA ND AR D D M X 5 1 2

1=GND 2=DATA3=DATA+

4 2

For Installations where long distance DMX cable connections are needed,we suggest to use a DMX terminator. The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3. The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

OUT

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

PIN 3

120 ohm

PIN 2

Page 12

XR1200 WASH

11.1-DMX Addresses

XR1200 WASH have 16 DMX channels.

Set the following addresses on the mixer:

Projector 1 A001 Projector 2 A017 If you want to select the next projector, just add “16”

Projector 3 A033 ….. A…. projector 6 A081

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.

TRICKS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.

12 FIRMWARE UPDATING

Warning: This procedure require a base knolewge of computer applications and Windows Hyperterminal program.

To update the software version of the Xr1200 WASH you will need: D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008). USB-DMX Driver for the D.T.S. RED BOX interface . (The driver and the installation procedure are available in our web site www.dts-lighting.it)

Updating the software version. Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using Windows Hyperterminal program.

Please refer to an authorised D.T.S. service centre.

It will be possible to download the software from the reserved area of D.T.S. web site: www.dts-lighting.it.

Page 13

XR1200 WASH

13- DISPLAY FUNCTIONS

DISPLAY

DMX OUT

DMX IN

DMX OUT

ENTER

DOWN

FUSE 16A T 5X20

MAINS

Electronic ballast

90-260V 50 / 60Hz

DISPLAY FUNCTIONS

The XR1200 display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections. NOTE: the symbol shows which key has to be pushed to obtain the desired function.

SOFTWARE VERSION: 8 motors R.20 / Pan&Tilt R.29

PAN DIRECTION This menu allow to set the Pan movement. Normal or Reversed

TILT DIRECTION This menu allow to set the Pan movement. Normal or Reversed

PAN TILT SPEED Pan Tilt Speed control (1-8)

Pan Direction

Up-Down

Tilt Direction

Up-Down

Pan Tilt Speed

Up-Down

Up-DownENTER

PAN DIRECTION

NORMAL

MENU ENTER DOWN UP

Up-DownENTER

TILT DIRECTION

NORMAL

MENU ENTER DOWN UP

Up-DownENTER

PAN TILT SPEED

Pan movement Normal or Reversed Default = Normal

Tilt movement Normal or Reversed Default = Normal

Pan Tilt Speed control (1-8) Default = 4

ENTER

MENU ENTER DOWN UP

Page 14

13- DISPLAY FUNCTIONS

XR1200 WASH

Up-Down

Display

DISPLAY FLIP / STAND BY / CONTRAST

Display Flip:

Reverses display's reading depending on the mounting position (On the ground or suspended).

Display Standby: To turn off the display (after 5 seconds) Or leave it always on.

Display Contrast: Display contrast regulation (1-16)

Up-DownENTER

DISPLAY

FLIP

Display Flip ON THE GROUND (Default) SUSPENDED

ENTER

ON THE GROUND

MENU ENTER DOWN UP

DISPLAY

STANDBY

FLIP

OFF

MENU ENTER DOWN UP

DISPLAY

CONTRAST

FLIP

Display Standby OFF = Display Standby disabled (Default) ON = Display goes OFF after 5 seconds

Display Contrast 1-16 (Default = 8)

ENTER

MENU ENTER DOWN UP

Up-Down

DMX Mode

Motors Test

Lamp

DMX MODE To select DMX mode : Mode 1 or Mode 2

TEST MODE Full test and single function test.

LAMP Lamp always ON, always OFF, lamp ON-OFF selectable via DMX And lamp life time reset

ADJUST To adjust the lamp with no mixer connected. It’s possible to set the parameters for PAN-TILT and ZOOM

Up-DownENTER

DMX MODE

Mode1 = 16 DMX channels, Pan&Tilt

ENTER

16 bit (Default) Mode2 = Same fixture as XR7 WASH

MODE 1

16 DMX channels, Pan&Tilt 16 bit (Please check at page 23 for details)

MENU ENTER DOWN UP

Up-DownENTER

MOTORS TEST

Motors Test

ENTER

ALL ,PAN, TILT, DIMMER, SHUTTER, COLOUR WHEEL, CYAN, MAGENTA,

ALL

YELLOW, EFFECTS, ZOOM

MENU ENTER DOWN UP

Up-DownENTER

LAMP

BY DMX

FLIP

BY DMX = ON / OFF via DMX (default) ALWAYS ON = Forced ON ALWAYS OFF = Forced OFF RESET COUNTER = Lamp life time

ENTER

reset

MENU ENTER DOWN UP

LAMP

ADJUST

FLIP

LAMP ADJUST =

with no mixer connected. It’s possible to set the parameters for PAN-TILT and ZOOM

To adjust the lamp

ENTER

MENU ENTER DOWN UP

Page 15

13- DISPLAY FUNCTIONS

XR1200 WASH

RESET Reset via DMX ENABLED / DISABLED and unit reset

FAN SPEED Fan Speed control

CMY BLACKOUT CMY filters blades inserted at 100% if the dimmer remain closed for more than 5 seconds. By activating this function, it will be possible to reduce substantially any visible light reflection coming out from the front lens when dimmer is closed.

Reset

Up-Down

Fan Speed

Up-Down

CMY Blackout

Up-Down

Up-DownENTER

RESET

BY DMX

ENABLED

MENU ENTER DOWN UP

Up-DownENTER

FAN SPEED

ENABLED = Reset via DMX enabled (Default) DISABLED = Reset via DMX disabled NOW = Unit motors reset

Fan speed control

ENTER

1-12 (Default = 12)

MENU ENTER DOWN UP

CMY BLACKOUT

ON = Blackout enabled (Default)

ENTER

OFF = Blackout disabled

MENU ENTER DOWN UP

Up-Down

System info

Reserved

SYSTEM INFO Lamp life time, lamp strikes, unit life time, 8 motors card software version, Pan&Tilt card software version and unit model

RESERVED

Pan lock-Tilt lock Pan free-Tilt free System Reboot (Code = 100)

Up-DownENTER

SYSTEM INFO

ENTER

Lamp life time, lamp strikes, unit life

LAMP LIFE:0006H STRIKE:003 UNIT LIFE: 0010H 8M R.20 PT R.29 MODEL: XR1200 WASH SILENT

MENU ENTER DOWN UP

Up-DownENTER

RESERVED

ENTER CODE

000

time, 8 motors card software version, Pan&Tilt card software version and unit model

Pan Lock = Lock the Pan to the desired value Tilt Lock = Lock the Tilt to the desired value

ENTER

Pan Free = Remove power to Pan

MENU ENTER DOWN UP

PAN LOCK

motor Tilt Free = Remove power to Tilt motor System Reboot = Unit Reboot without needing of turning OFF the unit

MENU ENTER DOWN UP

TILT LOCK

MENU ENTER DOWN UP

PAN FREE

MENU ENTER DOWN UP

TILT FREE

MENU ENTER DOWN UP

REBOOT

MENU ENTER DOWN UP

Page 16

13- DISPLAY FUNCTIONS

XR1200 WASH

Up-Down

Default

Frost

DEFAULT To restore main settings

Frost To be set “ YES” in case FROST filter 0506V016 provided as standard accessory in the box will be applied on the EFFECT wheel of the unit. This MENU affect ZOOM excursion

Up-DownENTER

DEFAULT

RESTORE MAIN SETTINGS

MENU ENTER DOWN UP

Default To restore main settings

ENTER

DEFAULT

RESTORE MAIN SETTINGS

SURE?

PRESS ENTER TO CONFORM

PRESS MENU TO CANCEL

MENU ENTER DOWN UP

Up-DownENTER

FROST

NOT

MENU ENTER DOWN UP

Frost Not = Not inserted (Default) Yes = Inserted

ENTER

14- ERROR MESSAGES

ERROR

COLOUR WHEEL

MENU ENTER DOWN UP

COLOUR WHEEL POSITION ERROR

ERROR

PAN

EFFECTS

MENU ENTER DOWN UP

BEAM SHAPE WHEEL POSITION ERROR

ERROR

TILT

ERROR

ZOOM LEFT

MENU ENTER DOWN UP

LEFT ZOOM SENSOR POSITION ERROR

ERROR

INTERNAL BUS

ERROR

ZOOM RIGHT

MENU ENTER DOWN UP

RIGHT ZOOM SENSOR POSITION ERROR

ERROR

DMX ADDRESS

MENU ENTER DOWN UP

PAN REPOSITIONING ENCODER ERROR

MENU ENTER DOWN UP

TILT REPOSITIONING ENCODER ERROR

MENU ENTER DOWN UP

COMMUNICATION PROBLEM BETWEEN 8 MOTORS CARD AND PAN&TILT CARD

MENU ENTER DOWN UP

DMX ADDRESS ERROR

Page 17

XR1200 WASH

15- HIDDEN MENU

For technical personnel only.

To operate this menu:

-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)

- Reset the XR1200 (reset from the MENU, not from the DMX controller!).

- While reset is running, press the MENU and ENTER keys at the same time.

CALIBRATION

MOTORS ALIGNMENT

PAN

134

MENU ENTER DOWN UP

ELECTRONIC CALIBRATION OF THE MOTORS

Calibration mode

CALIBRATION

MOTORS ALIGNMENT

PAN

134

MENU ENTER DOWN UP

PAN ALIGNMENT To align pan position

DEFAULT CAL

SET ALL MOTORS AT 128

MENU ENTER DOWN UP

RESET EEPROM. RESET ALL SETTINGS TO 128 VALUE

CALIBRATION

MOTORS ALIGNMENT

TILT

167

MENU ENTER DOWN UP

TILT ALIGNMENT To align tilt position

EXIT TO MAIN

MENU ENTER DOWN UP

EXIT FROM HIDDEN MENU

CALIBRATION

MOTORS ALIGNMENT

SHUTTER

145

MENU ENTER DOWN UP

SHUTTER ALIGNMENT To align shutter blades

CALIBRATION

MOTORS ALIGNMENT

COLOUR WHEEL

151

MENU ENTER DOWN UP

COLOUR WHEEL ALIGNMENT To align colour wheel

CALIBRATION

MOTORS ALIGNMENT

EFFECTS

149

MENU ENTER DOWN UP

EFFECTS ALIGNMENT To Align Effects wheel

CALIBRATION

MOTORS ALIGNMENT

MAGENTA

121

MENU ENTER DOWN UP

MAGENTA ALIGNMENT To align magenta colour

CALIBRATION

MOTORS ALIGNMENT

ZOOM RIGHT

MENU ENTER DOWN UP

ZOOM RIGHT ALIGNMENT To align zoom right position

CALIBRATION

MOTORS ALIGNMENT

YELLOW

106

MENU ENTER DOWN UP

YELLOW ALIGNMENT To align yellow colour

CALIBRATION

MOTORS ALIGNMENT

ZOOM LEFT

MENU ENTER DOWN UP

ZOOM LEFT ALIGNMENT To align zoom left position

CALIBRATION

MOTORS ALIGNMENT

CYAN

162

MENU ENTER DOWN UP

CYAN ALIGNMENT To align cyan colour

Page 18

XR1200 WASH

16- OPENING THE PROJECTOR HOUSING

It is possible to inspect the inside of the projector by removing the cover as indicated below.

ATTENTION

REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.

1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) .

2) Once unscrewed, simply lift the covers to access the internal components (photo 2).

Photo 1

Photo 2

17- PERIODIC CLEANING

17.1- Lenses and reflectors

Even a fine layer of dust can substantially reduce the luminous output . Regularly clean all lenses and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.

17.2- Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. If necessary, clean the fans and air passages more frequently.

18- PERIODIC CONTROLS Attention

Disconnect mains power prior to removing the projector housing.

Lamp

The lamp should be replaced if there is any visible damage or deformation due to heat. This will help to avoid the danger of the lamp exploding. Lamp lifespan is about 750 hours, then it is necessary to replace it.

Mechanical parts

Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them if necessary. Periodically check the lubrication of all components, particularly the parts subject to high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S. distributor. Check the tension of the belts and adjust it if necessary.

Electrical components

Check all electrical components for correct earthing and proper connection of all connectors; refasten them if necessary.

Fuse replacement

Locate the fuse, which protects the lamp and electronics, in the base of the XR1200. Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.

Page 19

19- DMX PROTOCOL

16 CHANNEL MODE ( 16bit)

1 PAN ms b ( 5 4 0°) 2 3 4 TILT l s b 5 6 D IM MER 7 SHU T T ER 8 C OL OUR 9 C YAN 10 MAGENTA 11 YEL L O W 12 SPEED CMY / DIMMER 13 MACRO CMY / COLOUR 14 E FF ECTS 15 ZOOM 16 RESET

DMX CHANNEL

PAN lsb

TILT msb(320°)

MOVEMENT SPEED

Parameter:

PAN msb 540°

PAN lsb

TILT msb 319°

TILT lsb

MOVEMENT SPEED

XR1200 WASH

DMX range

Value

0-10

11-25

26-127

128-247

248-255

DMX CHANNEL

DMX range

Value

0-8

9-255

Mid point

DMX value

Parameter:

Mid point

DMX value

Move

range

(degrees)

DIMMER

Move

range

(degrees)

Mode Option Function

Standard

Fast movement

Vector mode from fast to slow

Variable time reaction to

DMX signal ( fast to slow)

Slow reaction time to DMX

signal

Mode Option Function

Black-out

Proportional dimmer

Page 20

DMX CHANNEL

DMX range

Value

Parameter:

Mid point

DMX value

SHUTTER

Move

range

(degrees)

Mode Option Function

0-9 10-23 24-37 38-51 52-65 66-79 80-93

94-107 108-121 122-135 136-149 150-163 164-177 178-191 192-205 206-219 220-227 228-233 234-255

DMX CHANNEL

Parameter:

COLOUR

Strobe random speed

Strobe speed 1 min.

Strobe speed 2 Strobe speed 3 Strobe speed 4 Strobe speed 5

Strobe speed 6 max.

Flash open speed 1 min.

Flash open speed 2 Flash open speed 3

Flash open speed 4 max.

Flash closed speed 1 min.

Flash closed speed 2 Flash closed speed 3

Flash closed speed 4 max.

Colours / Macros in black-out

Pan / Tilt in black-out

XR1200 WASH

ARC 1200

Black-out

Open

DMX range

Value

0-12 13-25 26-38 39-51 52-64 65-77 78-90

91-103 104-116 117-129 130-142 143-155 156-168 169-181 182-197 198-200 201-203 204-206 207-209

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

White

Colour 1 (3200° K)

Colour 2 (5600°K)

Colour 3

BiColour 3/4

Colour 4

BiColour 4/5

Colour 5

BiColour 5/6

Colour 6

BiColour 6/7

Colour 7

Bicolour 7/8

Colour 8

Bicolour 8/white

Right rotation speed 1 max.

Right rotation speed 2 Right rotation speed 3 Right rotation speed 4

Page 21

210-212 213-215 216-218 219-221 222-224 225-228 229-231 232-234 235-237 238-240 241-243 244-246 247-249 250-252 253-255

DMX CHANNEL

Parameter:

CYAN

XR1200 WASH

ARC 1200

Right rotation speed 5 Right rotation speed 6 Right rotation speed 7 Right rotation speed 8

Right rotation speed 9 min

Stop

Left rotation speed 1 min.

Left rotation speed 2 Left rotation speed 3 Left rotation speed 4 Left rotation speed 5 Left rotation speed 6 Left rotation speed 7 Left rotation speed 8

Left rotation speed 9 max.

DMX range

Value

0-255

DMX CHANNEL

DMX range

Value

0-255

DMX CHANNEL

DMX range

Value

0-255

DMX CHANNEL

Mid point

DMX value

Parameter:

Mid point

DMX value

Parameter:

Mid point

DMX value

Parameter:

(degrees)

Move

range

Mode Option Function

MAGENTA

Move

range

Mode Option Function

YELLOW

Move

range

Mode Option Function

SPEED CMY / DIMMER

Proportional colour

DMX range

Value

0-7

8-255

Mid point

DMX value

(degrees)

Move

range

Mode Option Function

No Function

Variable speed from max to min

Page 22

DMX CHANNEL

DMX range

Value

0-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69 70-74 75-79 80-84

85-89 90-94

95-99 100-104 105-109 110-114 115-121 122-128 129-135

136-142 143-149 150-156 157-163 164-170 171-177 178-184 185-191 192-198 199-205

206-212 213-219 220-226 227-233 234-240 241-247 247-255

Parameter:

Mid point

DMX value

MACRO CMY / COLOUR

Move

range

(degrees)

XR1200 WASH

ARC 1200

Mode Option Function

No Function Macro 1 Macro 2 Macro 3

Macro

Macro 4 Macro

Macro 5 Macro

Macro 6 Macro

Macro 7 Macro

Macro 8 Macro

Macro 9 Macro

Macro 10 Macro

Macro 11 Macro

Macro 12

Macro

Macro 13 Macro

Macro 14 Macro

Macro 15 Macro

Macro 16 Macro

Macro 17 Macro

Macro 18 Macro

Macro 19 Macro

Macro 20 Macro

Macro

Macros rainbow wait =

Macros rainbow wait = 0 Macros rainbow wait =

Macros rainbow wait = 2

Macros rainbow wait = 3 Macros rainbow wait = 4 Macros rainbow wait =

Macros rainbow wait = 5 Macros rainbow wait =

Macros rainbow wait = 6 Macros rainbow wait = 7

Macros rainbow wait = 8 Macros rainbow wait = 9 Macros rainbow wait = 10

Full colours rainbow wait = 0 Full colours rainbow wait = 2 Full colours rainbow wait = 3 Full colours rainbow wait = 4

Full colours rainbow wait = 5 Full colours rainbow wait = 6

Full colours rainbow wait = 7 Full colours rainbow wait = 8 Full colours rainbow wait = 9

Full colours rainbow wait = 10

Page 23

DMX CHANNEL

DMX range

Value

Parameter:

Mid point

DMX value

EFFECTS

Move

range

(degrees)

0-19

20-39

40-255

DMX CHANNEL

DMX range

Value

0-225

DMX CHANNEL

Mid point

DMX value

Parameter:

ZOOM

Move

range

(degrees)

Parameter: LAMP / RESET

XR1200 WASH

Mode Option Function

Standard Frost inserted

No Frost inserted

Beam Shape

Mode Option Function

Proportional

ARC 1200

MODE 1 (DEFAULT)

DMX range

Value

0-9 10-60 61-129

130-179 180-200

201-239 240-255

Mid point

DMX value

30 95

154

190 220

247

Move

range

(degrees)

Mode Option Function

No Effect

Lamp OFF (Active after 3 seconds)

No Effect

Lamp ON (Active after 3 seconds)

No Effect

Internal Motors Reset

Total Reset

MODE 2 SAME AS XR 7 WASH (Please check at page 14 “DMX MODE” for details)

DMX range

Value

Mid point

DMX value

0-29

30-85

86 - 170 171-235

236-255

Move

range

(degrees)

Mode Option Function

No effect

Lamp OFF (active after 3

seconds)

Internal motor Reset

Total Reset

Lamp ON (active after 3

seconds)

Page 24

20- COLOUR WHEEL

XR1200 WASH

ARC 1200

COL1

0507K004 CONV.FILTER CTO TC3256

0507K003 CONV. FILTER CTB DL542

COL6COL5

COL3COL2

0507C046.D01 WOOD SW 460

COL7

COL4

0507C051.D01 ORANGE LW590

COL8

0507C042.D01 GREEN WB5055

0507C047.D01 RED LW 640

0507C041.D01 DARK BLUE SW490

0507C053.D01 AMBER LW 550

Page 25

21- 8 MOTORS CONTROL CARD

8 MOTORS CONTROL CARD

J7 Magnetic Sensors Connector

Line 1 Brown: Line 2 Orange:

GND ORANGE BROWN VCC

XR1200 WASH

Zoom motor1

(BLACK)

Zoom motor2

(DARK GREEN)

J1 Internal DATA Communication Connector From J8 Pan & Tilt card

30 VDC

Strobe

(YELLOW)

Colour wheel

(PINK)

Effects

(GREY)

Magenta

(LIGHT BLUE)

Cyan

(GOLD)

Fans

Yellow

(BLUE)

Fans

Page 26

22-PAN & TILT CARD

ENCODER PAN

(RED)

ENCODER TILT

(ORANGE)

PAN

(WHITE)

TILT

(BROWN)

GND

(BLACK)

30 VDC

(RED)

XR1200 WASH

ARC 1200

FAN

(WHITE)

TO J2

LAMP

ON-OFF

CARD

DATA 2

DATA 1

(VIOLET)

(LIGHT GREEN)

(BROWN)

MOTOR TILT

TO J1

DISPLAY CARD

(WHITE)

23-CABLES RESEND CARD

(ORANGE)

ENCODER TILT

25-LAMP ON-OFF CONTROL CARD

TO J1

8 MOTORS CARD

(GREEN)

24-DISPLAY CARD

DMX INPUT

(WHITE)

FROM J12 PAN&TILT

CARD

FROM J16 PAN&TILT CARD

TO J9 ELECTRONIC BALLAST

Page 27

NOTES

XR1200 WASH

ARC 1200

Page 28

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.

MADE IN ITALY

*0517I100*

0517I100

D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy

Tel. +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it www.dts-lighting.it