DTS XR10 SPOT User Manual

Page 1
GB
Made in Italy
XR10 SPOT
User’s Manual Rel 1.0
D.T.S. Illuminazione srl - ITALY http://www.dts-lighting.it
Page 2
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
D.T.S
D.T.S.
D.T.S.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S.
D.T.S.
D.T.S.
ARC 1200
XR10 SPOT
2
Page 3
3
ARC 1200
INDEX:
1- SYMBOLS 4 2- GENERAL WARNING 4 3- GENERAL WARRANTY CONDITION 4 4- TECHNICAL FEATURES 5 5- ACCESSORIES 7 6- IMPORTANT SAFETY INFORMATION 8
6.1 Fire prevention
6.2 Prevention of electric shock
6.3 Protection against ultraviolet radiation
6.4 Safety
6.5 Level of protection against the penetration of solid and liquid objects 7- MOUNTING THE LAMP 9
7.1 Lamp alignment 8- VOLTAGE AND FREQUENCY 10 9- INSTALLATION 10
9.1 Safety cable
9.2 Protection against liquids
9.3 Movement
9.4 Risk of fire
9.5 Forced ventilation
9.6 Ambient temperature 10- MAINS CONNECTION 11
10.1 Protection 11- DMX SIGNAL CONNECTION 12
11.1 DMX Addresses
11.2 Selecting the DMX address 12- FIRMWARE UPDATING 13 13- DISPLAY FUNCTIONS 14 14- PAN & TILT SPEED 17 15- FANS SPEED 16- ERROR MESSAGES 17 17- HIDDEN MENU 18 18- OPENING THE PROJECTOR HOUSING 19 19- REPLACING GOBOS 20- PERIODIC CLEANING 20
20.1 Lenses and reflectors
20.2 Fans and air passages 21- PERIODIC CONTROLS 22- DMX PROTOCOL 21 23- 8 MOTORS CONTROL CARD 36 24- 6 MOTORS CONTROL CARD 37 25- PAN & TILT CARD 38 26- CABLES RESEND CARD 27- DISPLAY CARD 28- LAMP ON-OFF CONTROL CARD 29- ROTATING GOBO WHEEL 39 30- FIXED GOBO WHEEL 40 31- COLOUR WHEEL 1 41 32- COLOUR WHEEL 2 42
XR10 SPOT
Page 4
ARC 1200
1- SYMBOLS
Graphic symbols used on this manual
2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important information regarding safety during installation , use and maintenance. The device is not for domestic use and must be installed by a qualified electrician or experienced person. Always disconnect the device from the mains before replacing the lamp. The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating. The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC SHOCK RISK
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON INFLAMMABLE SURFACES”
2M
THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT
4
F
THIS SYMBOL MEANS “RADIATION FROM THIS LAMP CAN CAUSE DAMAGE TO EYES AND SKIN”
!
UV
XR10 SPOT
Page 5
ARC 1200
4- TECHNICAL FEATURES
The XR10 SPOT is a brand new moving head fitted with a 575W discharge lamp,
, which delivers no less than 10.600 Lux at 5 m (12° beam angle).
The XR10 SPOT
The XR10 SPOT is one of the most complete moving heads in the 575W range and is particularly suitable for all professional applications, both mobile (concerts, shows, tours, special events) and fixed (clubs and other venues), requiring a compact light with a very high luminous output and versatility of functions. The XR10 SPOT incorporates motorized focus, motorized iris, motorized linear zoom (10°- 30°), 3-facet rotating prism, frost filter (soft edge). The XR10 SPOT features also a very flexible colour generation, thanks to two colour wheels with 7 colours each, including 3 colour conversion filters (3200°K, 5600°K and 6800°K), with linear selection for perfect 2-colour beams. 2 customizable gobo wheels are available, featuring respectively: 7 rotating and 16 bit indexable gobos; 8 fixed gobos. The XR10 SPOT also includes a new Pan / Tilt locking system with recessed buttons. The XR10 SPOT is the ideal moving head as well for all applications in which quiet operation is required, thanks to its silent internal ventilation system and silent pan/tilt operation.
XR 10 SPOT (Cod. 03.MS010.L)
• Electromagnetic ballast 230V 50/60 Hz • Black colour
XR 10 SPOT (Cod. 03.MS010.EB.L)
• Electronic ballast 90-245V 50/60 Hz • Black colour
Also available with white finish (RAL 9003) on demand. Also available with 120V or 100V power supply (Electromagnetic ballast version)
Lamp
Lamp: Philips MSR 575/2 Automatic switching ON of lamp in case of accidental switching OFF. Lamp ON/OFF via DMX; Reset via DMX.
Optical group
10.600 Lux at 5 m (12°) Dichroic glass reflector
Focus
Motorized focus
Iris
Motorized iris (16 bit)
Zoom
Motorized zoom (12°- 36°)
combined with a
dichroic parabolic reflector
is fitted with a Philips MSR 575/2 discharge lamp (GX9,5 lampholder base), with a
colour temperature of 7,200 °K and a luminous flux of 49,000 Lumens.
5
XR10 SPOT
Page 6
4- TECHNICAL FEATURES
Dimmer / shutter / strobo
Linear dimmer Shutter Strobe from 0,85 flash/sec to 6,75 flash/sec Power saving mode (the lamp dims to 50% six seconds after shutter closure)
Colours
2 Colour wheels (7 colours + open with linear selection) 3200°K and 5600°K colour conversion filters Colour change with blackout sync; rainbow effect
Gobos
2 gobo wheels: 1 rotating (7 indexable 16 bit gobos + open) and 1 fixed (8 gobos + open) Extractable gobo holders for both wheels Gobo change with synchronized blackout Gobo scrolling; Gobo shake
Effects
Indexable prism rotating in both directions (3-facet) Wash effect filter
Pan / Tilt
Pan 540° (3,9 sec.) Tilt 270° (2,6 sec.) 16-bit resolution 2-Speed function (2 selectable pan/tilt speeds); extremely smooth and precise movements even at the highest speeds Pan / Tilt locking system with recessed buttons Automatic Pan/Tilt repositioning in case of knocks
25 DMX channels (Default)
Internal operating system updatable via DMX
Connections
4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik POWERCONN connector by Neutrik
Power supply
Electronic ballast: 90 - 245 V (50/60 Hz) Electromagnetic ballast: 230 V (50/60 Hz)
Power consumption: 750 W Power saving mode (the lamp dims to 50% six seconds after shutter closure)
Thermal
Operating ambient temperature: -10° / 40°
Weight
On request: 100 V 50-60 Hz /120 V 60 HZ
26 Kg (electronic ballast) 32 Kg (magnetic ballast)
ARC 1200
6
XR10 SPOT
Page 7
4- TECHNICAL FEATURES
Dimensions
5- ACCESSORIES
As standard
•1 x MSR 575/2 lamp
•1 x POWERCONN male cable connector (cod. 0520P014)
•1 x XLR 5 Pins male cable connector (cod. 0508B028)
•1 x XLR 5 Pins female cable connector (cod. 0508B027)
•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• User’s manual
Optional (on request)
• Raincover for XR base (top) (cod. 03.MA001)
• Raincover for XR base (bottom) (cod. 03.MA002)
• Embedding flange for XR (visible display) (cod. 03.MA005)
• Embedding flange for XR (no visible display) (cod. 03.MA006)
• Wireless DMX receiver card (cod. 03.LA.012)
• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)
• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)
• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)
• Omega clamp with “Fast Lock” connection 1⁄4 turn (Cod. 02K00467)
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)
Unit Dimensions (LxWxH) 525x500x810mm 26 Kg (Electronic ballast) 32 Kg (Electromagnet ballast)
Packaging Dimensions (LxWxH) 610 x 540 x 720 mm 31,5 Kg (Electronic ballast) 37,5 Kg (Electromagnet ballast)
ARC 1200
7
408 mm
625 mm
500 mm
415 mm
18 0
mm
525 mm
270°
XR10 SPOT
Page 8
6- IMPORTANT SAFETY INFORMATION
6.1 Fire prevention:
MSR lamp
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1.5 MT.
-Minimum distance from the closest illuminable surface: 2 MT.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
6.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head, including lamp replacement.
-The level of technology inherent in the XR10 SPOT requires the assistance of specialised personnel for all servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
6.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged. Their respective shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
6.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
6.5 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid objects is IP 20. For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:
• Raincover for XR base (top) (cod. 03.MA001)
• Raincover for XR base (bottom) (cod. 03.MA002)
XR10 SPOT uses a PHILIPS 575/2 (other reccomended lamps: Philips 575 MSD).
ARC 1200
2M
8
F
!
!
UV
XR10 SPOT
Page 9
7- MOUNTING THE LAMPS
Warning: Switch off the unit before replacing the lamp.
1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .
2) .
3) . The lamp used on XR10 SPOT is made in quartz glass and should be handled with care. Always follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided in the lamp's packaging. . DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat the procedure.
4) . WARNING: Never look directly at the lamp when it’s lit. Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.
7.1 Lamp alignment
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic filters and other components inside the unit. The lamp alignment is also essential to obtain the maximum unifirmity and luminous performance by the projection.
3 adjusters X, Y and
Z (photo 5)
you will have an evenly projected light beam, with no shadows or
zones wich are brighter than others.
Remove the lamp holder assembly (photo2)
)Insert the lamp (photo 3)
The GX9,5 lamp socket is symmetrical
Replace the lamp assembly and tighten the screws A,B,C, which were previously removed (Photo4)
1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the
until you achieve a uniform flat field.
When the lamp is correctly optimized,
ARC 1200
Photo 2Photo 1 Photo 4Photo 3
Photo 5
9
Lamp
Alignment
UV
XR10 SPOT
Philips 575 MSR/2 Power 575W Luminous flux 49,000 lm Colour temperature 7.200°K Lampbase GX9,5 Rated life 1,000 hours
Philips 575 MSD Power 575W Luminous flux 43,000 lm Colour temperature 6.000°K Lampbase GX9,5 Rated life 3,000 hours
Page 10
8- VOLTAGE AND FREQUENCY
The XR10 SPOT with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.
9- INSTALLATION
XR10 SPOT may be either floor or ceiling mounted. For floor mounting installations, the XR10 SPOT is supplied with four rubber mounting feet on the base. For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface. The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as not to move or shake whilst the XR10 SPOT is moving. Four quarter turn fast locks placed on the base of the units, allows by using the two fast lock C clamps provided in the box, to fix the unit in any position. .
9.1- Safety cable
We recommend the use of a safety cable connected to the XR10 SPOT and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable can bear the weight of the entire unit. You may attach the safety cable to the two holes (A) located on the base of the fixture, as shown in the picture below.
9.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur.
The XR10 SPOT with electromagnetic ballast can operate at 230 VOLT 50 or 60 Hz (Standard).
On request: 100 V 50-60 Hz /120 V 60 HZ.
A
ARC 1200
!
240 mm
105 mm
10
XR10 SPOT
Page 11
9.3- Movement
The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any obstructions in the path of the projector's movement.
9.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 2 MT.
9.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on both the base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in operation. Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
9.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.
10- MAINS CONNECTION
XR10 SPOT with electronic ballast operate at 90-260 VOLT 50-60 Hz.
Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 6,3 amps at 230V, Or12 amps at 100-120 V Strict adherence to regulatory norms is strongly recommended.
10.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each XR10 SPOT. A good earth connection is essential for the correct operation of the projector.
XR10 SPOT with electromagnetic ballast operate at 230 VOLT 50-60 Hz
(On request: 100 V 50-60 Hz /120 V 60 HZ).
540°
270°
ARC 1200
11
2M
F
Fuse Holder
(12A T 5x20 Fuse)
!
WARNING
Do not place any object in the path
of the projector’s movement
XR10 SPOT
Electronic ballast 90-260V 50 / 60Hz Electromagnetic ballast 230 V 50/60 Hz (standard)
On request: 100 V 50-60 Hz 120 V 60 HZ
Page 12
11- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one. In this way, all the projectors are cascade connected. NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX terminator. The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3. The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
ARC 1200
12
5
3
4
2
1
1=GND 2=DATA­3=DATA+
CONTROLLER S T AN D A R D D M X 5 1 2
XR10 SPOT
Page 13
11.1-DMX Addresses
XR10 SPOT can be controlled with 18, 25 (default) or 26 DMX channels. If you want to use the unit in 25 channels mode (default), set the following addresses on the mixer:
Projector 1 A001 Projector 2 A026 If you want to select the next projector, just add “25”
11.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.
TRICKS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.
Projector 3 A051 ….. A…. projector 6 A126
12 FIRMWARE UPDATING
Warning: This procedure require a base knolewge of computer applications and Windows Hyperterminal program.
To update the software version of the XR10 SPOT you need: D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008). USB-DMX Driver for the D.T.S. RED BOX interface . (The driver and the installation procedure are available in our web site www.dts-lighting.it) Updated software version. Please follow the below procedure to perform the updating:
1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.
2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
4. Download the new software version into the unit by using Windows Hyperterminal program.
It will be possible to download the software from the reserved area of D.T.S. web site: www.dts-lighting.it.
Please refer to an authorised DTS service centre.
ARC 1200
13
!
XR10 SPOT
Page 14
13- DISPLAY FUNCTIONS
DISPLAY FUNCTIONS
The XR10 SPOT display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections. NOTE: the symbol shows which key has to be pushed to obtain the desired function.
Up-DownMENU ENTERUp-Down
PAN MOVEMENT INVERSION To reverse Pan movement from left to right and vice versa
Up-Down
Counterclockwise
Clockwise
Up-DownMENU ENTERUp-Down
TILT MOVEMENT INVERSION To reverse Tilt movement from bottom upwards and vice versa
Up-Down
Counterclockwise
Clockwise
Up-DownMENU ENTER
DMX MODE To select DMX mode : 25 (default), 26 or18 DMX channels
25 CHANNELS
(Pan & Tilt 16 bit)
18 CHANNELS
(Pan & Tilt 16 bit)
Up-Down
Up-Down
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
Up-Down
MENU
ENTERUp-Down
REVERSE DISPLAY Reverses display's reading depending on the mounting position (On the ground or suspended).
Up-Down
Floor
position
Suspension
position
Up-DownENTER
Up-DownENTER
DISPLAY STAND BY To turn off the display (after 5 seconds) Or leave it always on.
Display OFF
Display
always ON
ENTER
ENTER
ENTER
ENTER
DMX IN
DMX OUT
DISPLAY
MENU
ENTER
DOWN
UP
FUSE
12 A T 5x20
ARC 1200
14
DMX IN
DMX OUT
Default
Same fixture as XR9 SPOT
26 CHANNELS
(Pan & Tilt 16 bit)
Mains Electronic ballast: 90-260V 50 / 60Hz Electromagnetic ballast: 230 V 50/60 Hz (standard)
On request: 100 V 50-60 Hz 120 V 60 HZ
XR10 SPOT
Page 15
MENU
ENTER
DEFAULT To restore default setting
ENTER
Up-Down
MENU ENTER
Fan control To control the fan speed .
Up-Down
ENTER
Up-Down
(DEFAULT : 5 )
MENU ENTER
Up-Down
ENTER
ENTER
Up-Down
(DEFAULT : 2 )
SPEED control Pan&Tilt Speed control.
13- DISPLAY FUNCTIONS
ENTER
MENU
Up-Down
ENTER
MENU
Up-Down
ENTER
Up-Down
GOBO ROTATION DURING GOBO SCROLLING DISABLED (DEFAULT)
.
ENTER
SOFTWARE Software version for 8 motors and Pan&Tilt circuit Boards
MENU
Up-Down
RESET Al motors reset
RESET ENABLED VIA DMX
RESET DISABLED VIA DMX
TOTAL RESET
ENTER
ENTER
ENTER
ENTER
Up-Down
.
ARC 1200
FACTORY SETTINGS
8 MOTORS CIRCUIT BOARD (4.1) AND PAN&TILT CIRCUIT BOARD (2.7)
15
LAMP Lamp always ON-always OFF Or lamp ON-OFF selectable via DMX
ENTER
FORCED ON
ENTER
FORCED OFF
ENTER
ON / OFF VIA DMX (default)
MENU
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ADJUST To adjust the lamp with no mixer connected. It’s possible to set the parameters for PAN, TILT, FOCUS and ZOOM
ENTER
STRIKE Lamp strikes counter
ENTER
Up-Down
MENU
Up-Down
ENTER
AUTO FOCUS Automatic focusing during Zoom adjustment
.
Up-Down
AUTOMATIC FOCUS DISABLE (DEFAULT)
AUTOMATIC FOCUS ENABLE
ENTER
ENTER
GOBO1 Rotation Gobo1 Rotation during gobo scrolling
GOBO ROTATION DURING GOBO SCROLLING ENABLED
ENTER
XR10 SPOT
Page 16
MENU
Up-Down
ENTER
RESERVED Pan lock-Tilt lock, Pan free-Tilt free and System Reboot
Up
ENTER
.
ENTER
Up-Down
ENTER
ENTER
Up-Down
ENTER
ENTER
Up-Down
ENTER
Up-Down
.
ENTER
ENTER
ENTER
Up-Down
ENTER
ENTER
ENTER
Up-Down
.
.
ENTER
PAN LOCK LOCK THE PAN TO THE DESIRED VALUE
TILT LOCK LOCK THE TILT TO THE DESIRED VALUE
PAN FREE REMOVE POWER TO PAN MOTOR
TILT FREE REMOVE POWER TO TILT MOTOR
MENU ENTER
TIMER lamp life TIME (reset possible) and total UNIT LIFE TIME (reset not possible)
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ENTER
16
13- DISPLAY FUNCTIONS
ARC 1200
ENTER
ENTER
BOOT SYSTEM REBOOT
SYSTEM REBOOT
LAMP LIFE TIME
UNIT LIFE TIME
LAMP LIFE TIME COUNTER RESET
SILENT Silent operating mode during PAN&TILT movement. By activating this function, PAN and TILT motors will be driven with less power (during aceleration and deceleration) in order to reduce the noise during PAN&TILT rotation
ENTER
SILENT MODE DISABLED
ENTER
SILENT MODE ENABLED (DEFAULT)
MENU
Up-Down
ENTER
Up-Down
XR10 SPOT
Page 17
14- PAN & TILT SPEED (SPEE) (default: 1)
15- FAN SPEED (FANS)( default: 5)
You can set the PAN and TILT motors at high speed on your XR10 SPOT. Press menu until you see SPEE. Press ENTER and select a speed with UP-DOWN (there are 2 speeds). Confirm by pressing ENTER.
Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be less than 35° C.
ARC 1200
17
16- ERROR MESSAGES
ERROR: COLOR 2 WHEEL POSITION
ERROR: INTERNAL COMMUNICATION
ERROR: ENCODER PAN
ERROR: ENCODER TILT
ERROR: DMX ADDRESS
ERROR: LOAD DATA EEPROM
ERROR: EFFECTS POSITION (FROST - PRISM)
ERROR: COLOR 1 WHEEL POSITION
ERROR: FOCUS POSITION
ERROR: IRIS POSITION
ERROR: ROTATING GOBO WHEEL POSITION
ERROR: ROTATING GOBO INDEX POSITION
ERROR: FIXED GOBO WHEEL POSITION
ERROR: ZOOM POSITION
XR10 SPOT
Page 18
Up-DownENTER
PAN ALIGNMENT To align pan
ENTER
Up-DownENTER
TILT ALIGNMENT To align tilt
ENTER
Up-Down
Up-Down
ENTER
Up-DownENTERUp-Down
ROTATING GOBO WHEEL ALIGNMENT To align the rotating gobo wheel
ENTER
Up-DownENTER
Up-Down
GOBO ROTATION ALIGNMENT To align the gobo rotation (index)
ENTER
Up-DownENTERUp-Down
FOCUS ALIGNMENT To align focus
ENTER
Up-DownENTERUp-Down
COLOR 1 ALIGNMENT To align color wheel 1
ENTER
Up-DownENTERUp-Down
SHUTTER ALIGNMENT To align shutter blades
ENTER
Up-DownENTERUp-Down
EFFECT ROTATION ALIGNMENT To align prism on effects wheel (index)
ENTER
Up-DownENTERUp-Down
ZOOM ALIGNMENT To align Zoom
ES.
ENTER
17- HIDDEN MENU
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
- Reset the XR10 SPOT (reset from the MENU, not from the DMX controller!).
- While reset is running, press the MENU and ENTER keys at the same time.
Electronic calibration of the motors.
Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must repeat all previous calibrations)
Exit from hidden menu.
Up-DownENTERUp-Down
FIXED GOBO WHEEL ALIGNMENT To align the fixed gobo wheel
ENTER
Up-DownENTER
Up-Down
ES.
ENTER
Up-DownENTERUp-Down
COLOR 2 ALIGNMENT To align color wheel 2
ENTER
ARC 1200
18
!
Up-Down
ES.
Up-DownENTER ENTER
EFFECTS ALIGNMENT To align the effects wheel (frost and prism)
IRIS ALIGNMENT To align iris
XR10 SPOT
Page 19
19
18- OPENING THE PROJECTOR HOUSING
It is possible to inspect the inside of the projector by removing the cover as indicated below.
ATTENTION
REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.
1) Loosen the 3 screws which fix the head covers (photo 1) .
2) Once unscrewed, simply lift the covers to access the internal components (photo 2).
19- REPLACING GOBOS
XR10 SPOT uses a mechanical system which allows the fixture's gobos to be removed without the use of special tools. Replacement gobos should be made of either heat resistant glass or metal. An ever-increasing range of gobos is available from your DTS sales network. Gobo dimensions are as follows: ø external (ED) = 27.9 mm ø of image with defined edge (ID) = 24 mm thickness = from 0.2 to 4 mm (see catalogue)
Photo 1
Photo 2
ARC 1200
Load with coated surface toward the light source.
Max thickness
Coated side
When an object is held up the coated side of the glass gobo there is no space between the object and its reflection.
Uncoated side
When an object is held up the uncoated side of the glass gobo there is a space between the object and its reflection.
Coated side
Uncoated side
ED
ID
4 mm
XR10 SPOT
Page 20
Replacing gobos on the rotating gobo wheel
When replacing gobos, ensure that the projector is switched off.
1) Open the projector housing as described above.
2) Remove the gobo holder to allow easier access to the gobo (photo 1).
3) Release the gobo retaining spring and carefully remove the gobo (photo 3).
4) Reverse the procedure to install a replacement gobo.
20- PERIODIC CLEANING
20.1- Lenses and reflectors
Even a fine layer of dust can reduce the luminous output substantially. Regularly clean all lenses and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
20.2- Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. If necessary, clean the fans and air passages more frequently.
21- PERIODIC CONTROLS
Attention
Disconnect mains power prior to removing the projector housing.
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will help to avoid the danger of the lamp exploding. XR10 SPOT lamp lifespan is about 1000 hours, then it is necessary to replace it.
Mechanical parts
Periodically check all mechanical parts,gears, guides, belts, etc.for wear and tear, replacing them if necessary. Periodically check the lubrication of all components, particularly the parts subject to high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S. distributor. Check the tension of the belts and adjust it if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors, refastening if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the XR10 SPOT Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.
20
ARC 1200
Photo 1
Photo 3
!
UV
XR10 SPOT
Page 21
18 CHANNELS MODE
1 PAN msb 540°
2 PAN lsb 3 TILT msb 270° 4 TILT lsb 5 SPEED MOVEMENT 6 DIMMER 7 SHUTTER 8 COLOUR 1 9 COLOUR 2 10 ROTATING GOBO WHEEL 11 GOBO ROTATION / INDEX 12 FIXED GOBO WHEEL 13 IRIS 14 EFFECTS 15 EFFECTS ROTATION 16 FOCUS 17 ZOOM 18 LAMP ON-OFF / RESET
22- DMX PROTOCOL
21
DMX CHANNEL
1
Parameter: PAN msb
DMX CHANNEL
2
Parameter: PAN lsb
DMX CHANNEL
3
Parameter: TILT msb
DMX CHANNEL
4
Parameter: TILT lsb
DMX CHANNEL
5
Parameter: SPEED MOVEMENT
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-10
Standard
11-25
Fast movement
26-127
Vector mode from fast to slow
128-247
Variable time reaction to
DMX signal ( fast to slow)
248-255
Silent Mode
DMX CHANNEL
6
Parameter: DIMMER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-7
Black-out
8-255
Proportional dimmer
ARC 1200
XR10 SPOT
Page 22
DMX CHANNEL 8
Parameter: COLOUR 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-11
Colour1
12-23
Bicolour ½
24-35
Colour2
36-47
Bicolour 2/3
48-59
Colour3
60-71
Bicolour 3/4
72-83
Colour4
84-95
Bicolour 4/5
96-107
Colour5
108
-119
Bicolour 5/6
120-131
Colour6
132-143
Bicolour 6/7
144-155
Colour7
156-167
Bicolour 7/8
168-179
Colour8
DMX CHANNEL
7
Parameter: SHUTTER
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode Option Function
0-19
Black-out
20-39
Open
60-79
Strobe speed 1 min. (0,85 Hz)
80-89
Strobe speed 2 (1,4 Hz)
100-109
Strobe speed 3 (2 HZ)
110-119
Strobe speed 4 (3,75 Hz)
130-139
Strobe speed 5 (5 Hz)
140-149
Strobe speed 6 max. (6,75 Hz)
150-159
Pulse open speed 1 min.
160-169
Pulse open speed 2
170-179
Pulse open speed 3
180-189
Pulse open speed 4 max.
190-199
Pulse closed speed 1 min.
200-209
Pulse closed speed 2
210-219
Pulse closed speed 3
220-227
Pulse closed speed 4 max.
228-233
Colour and Gobo in black-out
234-255
Pan and Tilt in black-out
Open
40-59
Black-out
120-129
Random Strobe
90-99
ARC 1200
22
XR10 SPOT
Page 23
180-197
Bicolour 8/1
198-200
Right rotation speed 9 max.
201-203
Right rotation speed 8
204-206
Right rotation speed 7
207-209
Right rotation speed 6
210-212
Right rotation speed 5
213-215
Right rotation speed 4
216-218
Right rotation speed 3
219-221
Right rotation speed 2
222-224
Right rotation speed 1 min.
225-228
Stop
229-231
Left rotation speed 1 min.
232-234
Left rotation speed 2
235-237
Left rotation speed 3
238-240
Left rotation speed 4
241-243
Left rotation speed 5
244-246
Left rotation speed 6
247-249
Left rotation speed 7
250-252
Left rotation speed 8
253-255 Left rotation speed 9 max.
DMX CHANNEL 9
Parameter: COLOUR 2
ARC 1200
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-11
Colour1
12-23
Bicolour ½
24-35
Colour2
36-47
Bicolour 2/3
48-59
Colour3
60-71
Bicolour 3/4
72-83
Colour4
84-95
Bicolour 4/5
96-107
Colour5
108
-119
Bicolour 5/6
120-131
Colour6
132-143
Bicolour 6/7
144-155
Colour7
156-167
Bicolour 7/8
168-179
Colour8
23
XR10 SPOT
Page 24
DMX CHANNEL 10
Parameter: ROTATING GOBO WHEEL
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-25
Open
26-51
Gobo 1
52-77
Gobo 2
78-103
Gobo 3
104-129
Gobo 4
130-155
Gobo 5
156-181
Gobo 6
182-207
Gobo 7
208-213
Speed rotation 1 min.
214-219
Speed rotation 2
220-225
Speed rotation 3
226-231
Speed rotation 4
232-237
Speed rotation 5
238-243
Speed rotation 6
244-249
Speed rotation 7
250-255
Speed rotation 8 max.
DMX CHANNEL
11
Parameter: ROTATING GOBO WHEEL ROTATION/INDEX
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-127
Proportional index 0° / 360°
128-180
Left rotation
181-202
Stop
203-255
Right rotation
ARC 1200
180-197
Bicolour 8/1
198-200
Right rotation speed 9 max.
201-203
Right rotation speed 8
204-206
Right rotation speed 7
207-209
Right rotation speed 6
210-212
Right rotation speed 5
213-215
Right rotation speed 4
216-218
Right rotation speed 3
219-221
Right rotation speed 2
222-224
Right rotation speed 1 min.
225-228
Stop
229-231
Left rotation speed 1 min.
232-234
Left rotation speed 2
235-237
Left rotation speed 3
238-240
Left rotation speed 4
241-243
Left rotation speed 5
244-246
Left rotation speed 6
247-249
Left rotation speed 7
250-252
Left rotation speed 8
253-255 Left rotation speed 9 max.
24
XR10 SPOT
Page 25
25
DMX CHANNEL 12
Parameter: GOBO 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-22
Open
23-45
Gobo 1
46-68
Gobo 2 Gobo 3
92-114
Gobo 4 Gobo 5 Gobo 6
161-183
Gobo 7 184-207 208-213 214-219 220-225
Speed rotation 1 min
226-231
Speed rotation 2
232-237
Speed rotation 3
238-243
Speed rotation 4
244-255
Speed rotation 5 Speed rotation 6 Speed rotation 7 max
Gobo 8
DMX CHANNEL 13
Parameter: IRIS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-005
Open
006-159
Linear Iris from Open to Closed
Iris pulse at different speeds from Max to Min
160-171 172-199 200-227 228-255
Iris pulse with flash closing from Min to Max Iris pulse with flash openig from Min to Max
Closed
DMX CHANNEL 14
Parameter: EFFECTS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-085
No effect
086-171
3 facet prism
172-255
Frost
ARC 1200
69-91
115-137
138-160
XR10 SPOT
Page 26
DMX CHANNEL 15
Parameter: EFFECTS ROTATION
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode Option Function
0-009
Stop
DMX CHANNEL
16
Parameter: FOCUS
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode Option Function
0-255
Linear focus
DMX CHANNEL 17
Parameter: ZOOM
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode Option Function
0-255
Linear zoom
26
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode Option Function
DMX CHANNEL 18
Parameter: RESET / LAMP
0-9
No Effect 10-60 Lamp OFF (activ.after 3 seconds) 61-129
130-179
Internal motor reset
Total Reset
180-200 201-239 240-255
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
ARC 1200
10
-127
Left rotation from fast to slow
128
-
137
Stop
138
-255
Right rotation from slow to fast
XR10 SPOT
Page 27
25 CHANNELS MODE (DEFAULT)
1 PAN msb 540° 2 PAN lsb 3 TILT msb 270° 4 TILT lsb 5 SPEED MOVEMENT 6 DIMMER 7 SHUTTER 8 COLOUR 1 9 COLOUR 1 MODE 10 COLOUR 2 11 COLOUR 2 MODE 12 GOBO 1 13 GOBO 1 MODE 14 GOBO 1 ROTATION/INDEX COARSE 15 GOBO 1 INDEX FINE 16 bit 16 GOBO 1 SHAKE 17 GOBO 2 18 GOBO 2 SHAKE 19 IRIS 20 IRIS MACROS 21 EFFECTS 22 EFFECTS ROTATION 23 FOCUS 24 ZOOM 25 LAMP ON/OFF - RESET
27
DMX CHANNEL
1
Parameter: PAN msb
DMX CHANNEL
2
Parameter: PAN lsb
DMX CHANNEL
3
Parameter: TILT msb
DMX CHANNEL
4
Parameter: TILT lsb
DMX CHANNEL
5
Parameter: SPEED MOVEMENT
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-10
Standard
11-25
Fast movement
26-127
Vector mode from fast to slow
128-247
Variable time reaction to
DMX signal ( fast to slow)
248-255
Silent movement
ARC 1200
XR10 SPOT
Page 28
DMX CHANNEL 6
Parameter: DIMMER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
28
0-7
Black-out
8-255
Proportional dimmer
DMX CHANNEL 8
Parameter: COLOUR 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-31
32
-63 64-95 96
-127
128-159
IF CHANNEL 9 = FULL COLOUR (Dmx range value 0 - 63)
160-191 192-223
224-255
Colour1
Colour3
Colour2
Colour4 Colour5 Colour6
Colour7 Colour8
ARC 1200
DMX CHANNEL
7
Parameter: SHUTTER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-19
Black-out
20-39
Open
60-79
Strobe speed 1 min. (0,85 Hz)
80-89
Strobe speed 2 (1,4 Hz)
100-109
Strobe speed 3 (2 HZ)
110-119
Strobe speed 4 (3,75 Hz)
130-139
Strobe speed 5 (5 Hz)
140-149
Strobe speed 6 max. (6,75 Hz)
150-159
Pulse open speed 1 min.
160-169
Pulse open speed 2
170-179
Pulse open speed 3
180-189
Pulse open speed 4 max.
190-199
Pulse closed speed 1 min.
200-209
Pulse closed speed 2
210-219
Pulse closed speed 3
220-227
Pulse closed speed 4 max.
228-233
Colour and Gobo in black-out
234-255
Pan and Tilt in black-out
Open
40-59
Black-out
120-129
Random Strobe
90-99
XR10 SPOT
Page 29
29
DMX CHANNEL 8
Parameter: COLOUR 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-27 28-55 56-83 84-111
112-139
IF CHANNEL 9 = HALF COLOUR (Dmx range value 64 - 127)
140-167
168-195
224-255
196-223
Bicolour 1/ 2 Bicolour 2/ 3 Bicolour 3/ 4 Bicolour 4/ 5
Bicolour 5/ 6 Bicolour 6/ 7 Bicolour 7/ 8
Colour 1
Bicolour 8/ 1
0-10
11-255
IF CHANNEL 9 = PROPORTIONAL COLOUR (Dmx range value 128 - 191)
Proportional colour
No Colour
IF CHANNEL 9 = RAINBOW (Dmx range value 192 - 255)
0-9
10-127
Right Rot.Speed from Max to Min
No Colour
128-137 138-255
Left Rot.speed from Min to Max
Stop
DMX CHANNEL 9
Parameter: COLOUR 1 MODE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-63
64-127
Half Colour
Full Colour
128-191 192-255
Rainbow
Proportional Colour
DMX CHANNEL 10
Parameter: COLOUR 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-31 32-63 64-95 96-127
128-159
IF CHANNEL 11 = FULL COLOUR (Dmx range value 0 - 63)
160-191 192-223
224-255
Colour1
Colour3
Colour2
Colour4 Colour5 Colour6
Colour7 Colour8
ARC 1200
XR10 SPOT
Page 30
DMX CHANNEL 10
Parameter: COLOUR 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-27 28-55 56-83 84-111
112-139
IF CHANNEL 11 = HALF COLOUR (Dmx range value 64 - 127)
140-167
168-195
224-255
196-223
234-255
Bicolour 1 /2 Bicolour 2/3
Bicolour 3/4 Bicolour 4/5
Bicolour 5/6 Bicolour 6/7 Bicolour 7/8
Colour 1
Bicolour 8/9
Bicolour 9/1
0-10
11-255
IF CHANNEL 11 = PROPORTIONAL COLOUR (Dmx range value 128 - 191)
Proportional colour
No Colour
IF CHANNEL 11 = RAINBOW (Dmx range value 192 - 255)
0-9
10-127
Right Rot.Speed from Max to Min
No Colour
128-137 138-255
Left Rot.speed from Min to Max
Stop
DMX CHANNEL 11
Parameter: COLOUR 2 MODE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-63
64-127
Half Colour
Full Colour
128-191 192-255
Rainbow
Proportional Colour
30
DMX CHANNEL
12
Parameter: GOBO 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-25 26-51 52-77 78-103
130-155
156-181
208-213
Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5
Gobo 6
Rotation speed 1 min.
Open
104-129
Gobo 7
182-207
ARC 1200
XR10 SPOT
Page 31
31
DMX CHANNEL
12
Parameter: GOBO 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Rotation speed 2
214-219 220-225
226-231 232-237
238-243 244-249 250-255
Rotation speed 3 Rotation speed 4 Rotation speed 5
Rotation speed 7
Rotation speed 8 Max
Rotation speed 6
DMX CHANNEL
13
Parameter: GOBO 1 MODE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Gobo Rotation Mode
0-127
128-255
Gobo Index Mode
DMX CHANNEL 14
Parameter: GOBO 1 ROTATION/GOBO 1 INDEX COARSE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-9 10-127
128-137 138-255
IF CHANNEL 13 = Gobo Rotation Mode (Dmx range value 0 - 127)
SX Rot. Prop. Speed Max to Min
Stop
DX Rot. Prop. Speed Min to Max
Stop
0-255
IF CHANNEL 13 = Gobo Index Mode (Dmx range value 128 - 255)
Gobo index Coarse
DMX CHANNEL
15
Parameter: GOBO 1 INDEX FINE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Gobo Index Fine
0-255
DMX CHANNEL
16
Parameter: GOBO 1 SHAKE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Stop
0-9
10-22
23-35 36-48
Gobo Shake R-L Speed 1 Min. Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
ARC 1200
XR10 SPOT
Page 32
DMX CHANNEL
16
Parameter: GOBO 1 SHAKE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
49-61 62-74 75-87
88-100
101-113 114-126
127-138 139-151
Gobo Shake R-L Speed 4 Gobo Shake R-L Speed 5 Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7 Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min Gobo Shake L-R Speed 2 Gobo Shake L-R Speed 3 Gobo Shake L-R Speed 4 Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7 Gobo Shake L-R Speed 8
152-164
165-177
178-190 191-203
204-216 217-229 230-242 243-255
Gobo Shake L-R Speed 9 Max
32
DMX CHANNEL
17
Parameter: GOBO 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-22
Open
23-45
Gobo 1
46-68
Gobo 2
69-91
Gobo 3
92-114
Gobo 4
115
-137
Gobo 5
138 -160
Gobo 6
161-183
Gobo 7 184-207 208-213 214-219 220-225 226-231
Speed rotation 1 min
232-237
Speed rotation 2
238-243
Speed rotation 3
244-255
Speed rotation 4
Gobo 8
ARC 1200
Speed rotation 5
Speed rotation 7 max
Speed rotation 6
XR10 SPOT
Page 33
DMX CHANNEL
18
Parameter: GOBO 2 SHAKE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Stop
0-9
10-22
23-35 36-48
Gobo Shake R-L Speed 1 Min. Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
49-61 62-74 75-87
88-100
101-113 114-126
127-138 139-151
Gobo Shake R-L Speed 4 Gobo Shake R-L Speed 5 Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7 Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2 Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4 Gobo Shake L-R Speed 5 Gobo Shake L-R Speed 6 Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
152-164
165-177
178-190 191-203
204-216 217-229 230-242 243-255
Gobo Shake L-R Speed 9 Max
33
DMX CHANNEL 19
Parameter: IRIS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-5
Iris pulse at different speeds from Min to Max
Iris pulse with flash closing from Min to Max
Iris pulse with flash opening from Min to Max
DMX CHANNEL 20
Parameter: IRIS MACROS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
No effect
0-9 10-91 92-173
174-255
ARC 1200
0-
Open
6-255
Linear Iris from Open to Closed
Linear Iris from Open to Closed
XR10 SPOT
Page 34
DMX CHANNEL 21
Parameter: EFFECTS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
No effect
3 facet prism
Stop
34
DMX CHANNEL 22
Parameter: EFFECTS ROTATION
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
DMX CHANNEL 23
Parameter: FOCUS
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode Option Function
0-255
Linear Focus
DMX CHANNEL
24
Parameter: ZOOM
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode Option Function
0-255
Linear zoom
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
DMX CHANNEL 25
Parameter: RESET
0-9
No Effect 10-60 Lamp OFF (activ.after 3 seconds) 61-129
130-179
Internal motor reset
Total Reset
180-200 201-239 240-255
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
0-085
86-171
0-9 10-127 128-143
Right Rotation from slow to fast
144-255
Left Rotation from fast to slow
Stop
ARC 1200
Frost
172-255
XR10 SPOT
Page 35
26 CHANNELS MODE (SEE THE 25 CHANNELS MODE FOR DETAILS) 1 PAN msb 540° 2 PAN lsb 3 TILT msb 270° 4 TILT lsb 5 SPEED MOVEMENT 6 DIMMER 7 SHUTTER 8 COLOUR 1 9 COLOUR 1 MODE 10 COLOUR 2 11 COLOUR 2 MODE 12 GOBO 1 13 GOBO 1 MODE 14 GOBO 1 ROTATION/INDEX COARSE 15 GOBO 1 INDEX FINE 16 bit 16 GOBO 1 SHAKE 17 GOBO 2 18 GOBO 2 SHAKE 19 IRIS 20 IRIS MACROS 21 EFFECTS 22 EFFECTS ROTATION 23 NOT USED 24 FOCUS 25 ZOOM 26 LAMP ON/OFF - RESET
35
ARC 1200
XR10 SPOT
Page 36
23- 8 MOTORS CONTROL CARD
36
ARC 1200
Fans
+
-
GND ORANGE BROWN VCC
30 VDC
J1 Internal DATA Communication Connector From J8 Pan & Tilt card
Fans
J7 Magnetic Sensors Connector
Line 1 Brown Line 2 Orange
Rotating gobo wheel
(BLACK)
Fixed gobo wheel
(DARK GREEN)
Strobe
Colour 1
(LIGHT BLUE)
(YELLOW)
Colour 2
(GREY)
8 MOTORS CONTROL CARD
J26 to 6 Motors
Control card
J9 from J3 Lamp ON-OFF control card
XR10 SPOT
Page 37
24- 6 MOTORS CONTROL CARD
37
ARC 1200
6 MOTORS CONTROL CARD
Iris
(RED)
Effect rotation
(DARK ORANGE)
Effects
(LIGHT ORANGE)
Gobo rotation
(BROWN)
Focus
(VIOLET)
Zoom
(YELLOW)
+
-
30 VDC
J1 from 8 Motors
Control card
XR10 SPOT
Page 38
25-PAN & TILT CARD
38
ARC 1200
DATA 1
DATA 2
(VIOLET)
(LIGHT GREEN)
MOTOR TILT
(BROWN)
ENCODER TILT
(ORANGE)
FROM J12 PAN&TILT
CARD
27-DISPLAY CARD
BLACK RED
BLACK BLACK
26-CABLES RESEND CARD
28-LAMP ON-OFF CONTROL CARD
PAN
(WHITE)
TILT
(BROWN)
GND
(BLACK)
30 VDC
(RED)
FAN
(WHITE)
ENCODER TILT
(ORANGE)
ENCODER PAN
(RED)
DMX INPUT
(WHITE)
TO J1
8 MOTORS CARD
(VIOLET)
TO J2
LAMP
ON-OFF
CARD
TO J1
DISPLAY CARD
(WHITE)
J2
J3
J4
FROM J16 PAN&TILT CARD
TO J9 ELECTRONIC BALLAST
XR10 SPOT
Page 39
39
1
2
3
4
5
6
7
29- ROTATING GOBO WHEEL
0516G032.01
GOBO 1 DICRO
0516G032.10
GOBO 4 DICRO GOBO 5 DICRO GOBO 6 DICRO
0516G032.11-B 0516G032.03
ARC 1200
0516G032.08.M
GOBO 2 METAL
GOBO 3 METAL
0516G032.12.M
0516G032.05
GOBO 7 DICRO
XR10 SPOT
Page 40
40
30- FIXED GOBO WHEEL
ARC 1200
1
2
3
4
5
6
7
8
GOBO 7 METAL GOBO 8 METAL
0516G032.13.M
0516G032.02.M
GOBO 2 DICRO GOBO 3 METAL GOBO 4 METAL
0516G032.04 0516G032.08.M 0516G032.07.M
GOBO 1 DICRO
0516G032.06
GOBO 5 GLASS
0516G032.14
GOBO 6 DICRO
0516G032.09
XR10 SPOT
Page 41
0507C045.D10 CYAN SW 530
0507C051.D10 ORANGE LW590
0507C043.D10 LAVANDER SL0064
0507C041.D10 DARK BLUE SW490
COL5COL4
COL3COL2
COL6
COL7
COL1
0507C058.D10 PINK SL4758
0507C047.D10 RED LW 640
0507C049.D10 YELLOW LW 515
31- COLOUR WHEEL 1
1
2
3
4
5
6
7
41
ARC 1200
XR10 SPOT
Page 42
COL5
COL3COL2
COL6
COL7
COL1
32- COLOUR WHEEL 2
42
0507C053.D10 AMBER LW550
0507C046.D10 WOOD SW460
0507K003.D10 CONV. FILTER COLD DL542
0507K004.D10 CONV.FILTER HOT TC3256
0507C038.D10 MAGENTA SL 4763
0507K005.D10 HALF CONV.FILTER HOT TC3256
ARC 1200
1
2
3
4
5
6
7
0507C042.D10 GREEN WB5055
COL4
XR10 SPOT
Page 43
NOTES
43
ARC 1200
XR10 SPOT
Page 44
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from DTS.DTS reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. DTS assumes no responsibility for the use or application of the products or circuits described herein.
MADE IN ITALY
D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy
Tel. +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it www.dts-lighting.it
44
Loading...