Page 1
XM 2500 SPOTXM 2500 SPOT
GB
User Manual Rel 1.0
Page 2
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della DTS .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. DTS non assume alcuna responsabilità sull'uso o sull'applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de DTS.
DTS se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou de
design, sans préavis, à chacun de ses produits. DTS décline toute responsabilité sur l'utilisation ou sur
l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas.
Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes. Todos los derechos han
sido reservados y este documento no puede ser copiado, fotocopiado o reproducido, total o
parcialmente, sin previa autorizaciónescrita de DTS.
DTS se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter estético,
funcional o de diseño a cada producto suyo. DTS no se asume responsabilidad de ningún tipo sobre la
utilización o sobre la aplicación
de los productos o de los circuitos descritos.
ARC 1200
XM 2500 SPOT
2
Page 3
INDEX:
1- TECHNICAL FEATURES 4
2- IMPORTANT SAFETY INFORMATION 5
2.1 Fire prevention
2.2 Prevention of electric shock
2.3 Protection against ultraviolet radiation
2.4 Safety
2.5 Level of protection against the penetration of solid and liquid matter
3- MOUNTING THE LAMPS 6
3.1 Lamp alignment
4- VOLTAGE AND FREQUENCY 7
5- INSTALLATION 7
5.1 Safety chain
5.2 Protection against liquids
5.3 Movement
5.4 Risk of fire
5.5 Forced ventilation
5.6 Ambient temperature
6- MAINS CONNECTION 8
6.1 Protection
7- DMX SIGNAL CONNECTION 8
7.1 DMX Addresses
7.2 Selecting the DMX address
8- DISPLAY FUNCTIONS 11
9- ERROR MESSAGES 14
10- HIDDEN MENU 15
11- OPENING UP THE PROJECTOR HOUSING 17
12- REPLACING GOBOS
13- PERIODIC CLEANING 18
13.1 Lenses and reflectors
13.2 Fans and air passages
13.3 Periodic controls
14- CONTROL MOTORS CARD 19
15- DISPLAY CARD 21
16-PAN & TILT CARD
17- LAMP ON-OFF CONTROL CARD
18-CABLES RESEND CARD
19- DMX PROTOCOL 22
ARC 1200
3
XM 2500 SPOT
Page 4
ARC 1200
4
1- TECHNICAL FEATURES
The XM 2500 Spot is fitted with a Philips MSR 1200/SA discharge lamp
(GY22 lampholder base), with a colour temperature of 5,600 °K and a luminous flux of
96,000 Lumens.
Duration is 750 hours, with replacement recommended before 1000 hours
Other recommended lamps: Osram HTI 1200W/SE PP; GE Lighting CSR1200W SA
The unit incorporates:
Motorized Focus system
8°-13° motorized Zoom with auto-focus
Dimmer (emitted light is controlled by progressive and linear dimming).
Shutter (instantaneous shutter opening/closure)
Strobe: mechanical strobe effect (frequency variable from 0.86 flashes/sec to 6.6
flashes/sec).
Motorized iris
2 gobo wheels (6 indexable 16 bit gobos + open each)
CMY linear colour mixing system
Colour wheel (7 colours + open)
3 rotating prisms
Frost
Electronic or magnetic ballast
Pan: 540° in 5.6 seconds (8 or 16 bit) with auto repositioning system
Tilt: 270° in 4.3 seconds (8 or 16 bit) with auto repositioning system
USITT Standard DMX 512 input
4-digit LED display with 4 buttons
Power Supply: 190-245 V (50/60 Hz).
Power consumption: 1300 W.
Energy saving function is automatic when the fixture is blacked out.
The XM 2500 SPOT is also available with a magnetic ballast, with selectable power supply
(220/230/240 V). Power consumption is 1300 W.
Remote Lamp on/off via DMX
Net weight: 45 Kg (with electronic ballast); 55 Kg (with magnetic ballast).
Packaging Dimensions (LxWxH)
680x680x780mm
Weight: 50 Kg (with electronic ballast)
60 Kg with magnetic ballast
XM 2500 SPOT
Page 5
2- IMPORTANT SAFETY INFORMATION
2.1 Fire prevention:
-XM2500 is fitted with a Philips 1200W MSR/SA lamp.
-Other recommended lamps are: Osram HTI 1200W/SE PP; GE Lighting CSR1200W SA
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 m.
-Minimum distance from the closest illuminable surface: 1 m.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
2.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head, including lamp replacement.
-The level of technology inherent in the XM2500 requires the assistance of specialised personnel for all
servicing.Please refer to an authorised D.T.S. service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
2.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
2.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety chain to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
2.5 Level of protection against the penetration of solid and liquid matter:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid matter is IP 20. XM2500 uses Philips 1200 MSR/SA lamp with GY 22 socket.
The temperature inside the projector can reach 250° C after just 5 minutes, but it can get as high as
350° C. Always check that the lamp is cold before attempting to remove it. In any case, only open the
unit 10 minutes after it has been turned off
ARC 1200
5
XM 2500 SPOT
Page 6
3- MOUNTING THE LAMPS:
Warning: Switch off the unit before replacing the lamp.
Philips MSR1200/SA
Power 1200W
Luminous flux 96,000 lm
Colour temperature 5.600°K
Lamp base GY 22
Rated life 800 hours
1) Using a screwdriver, remove the 4 screws (A,B, C,D) (photo 1) which fix the lamp holder.
2) Remove the lamp holder assembly (photo2).
Insert the lamp (photo 3).
The lamp used on XM 2500 is made in quartz glass and should be handled with care. Always follow the
instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided
in the lamp's packaging. The GY22 lamp socket is not symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat
the procedure.
3) Replace the lamp assembly and tighten the screws (A,B,C,D) which were previously removed (photo
4).
3.1 Lamp alignment:
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic
filters and other components inside the unit.
Alignment is carried out using the 3 adjusters X, Y and Z.
During this operation you must have a uniform luminosity all around the projected area.
Osram HTI 1200W/SE PP
Power 1200W
Luminous flux 105,000 lm
Colour temperature 5.400°K
Lamp base GY 22
Rated life 750 hours
ARC 1200
6
Photo 2Photo 1 Photo 4Photo 3
GE Lighting CSR1200W SA
Power 1200W
Luminous flux 100,000 lm
Colour temperature 5.800°K
Lamp base GY 22
Rated life 750 hours
Photo 5
XM 2500 SPOT
Page 7
4- Voltage and frequency
The XM2500 E.B.(ELECTRONIC BALLAST) can operate at 190-245 VOLT 50 or 60 Hz.
5- Installation
XM2500 may be either floor or ceiling mounted.
For floor mounting installations, the XM2500 is supplied with four rubber mounting feet on the
base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to
the mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of
the unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as
not to move or shake whilst the XM2500 is moving.
Eight quarter-turn fast locks placed on the base of the units allow - by using the two Omega
Clamps provided in the box - to fix the unit in any position.
.
Safety chain
We recommend the use of a safety cable or chain connected to the XM2500 and to the suspension
truss in order to avoid the fixture accidental fall, should the main fixing point fail. Make sure
that the iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown
in the picture below.
Protection against liquids
The projector contains electric and electronic components which should under no circumstances
come into contact with oil, water or any other liquid. The proper unit functioning would be
compromised should this occur.
A
ARC 1200
7
XM 2500 SPOT
quarter turn
fast locks
quarter turn
fast locks
Page 8
Movement
The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any
obstructions in the path of the projector's movement.
Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum
recommended distance from flammable material is 0.5m.
Minimum distance from the object being illuminated is 2 m.
Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on
both the base and head of the fixture. These should, under no circumstances, be blocked or
obstructed whilst the projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient
temperature should NOT exceed 40°C.
6- MAINS CONNECTION
XM2500 operates at 190-245V at 50 or 60Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is of a suitable rating of 8 amps at 230V.
Strict adherence to regulatory norms is strongly recommended.
Protection
The use of a thermal magnetic circuit breaker is recommended for each XM2500.
A good earth connection is essential for the correct operation of the projector.
7- DMX signal connection
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø0.5 mm cable and
a CANNON XLR 5 or 3 pole connector.
190-245V 50 / 60Hz
ARC 1200
8
540°
270°
XM 2500 SPOT
Page 9
Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR
chassy.
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and
connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX
IN plug of the second one.
This way all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
The standard configuration of the XM2500 is with XLR 5 pins connection.
To convert to an XLR 3 pins configuration proceed as follows:
1) Remove the 4 screws fixing the display cover panel to the unit (photo 1).
2) Remove the screws that fix the XLR connectors to the panel (photo 2).
3) Rotate the electronic card by 180° (photo 3).
4) Place the 3 pins XLR connectors in the special holes and close.
For Installations where long distance DMX cable connections are needed,we suggest
to use a DMX terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
between pin 2 and 3.
The DMX terminator must be plugged in the last unit (DMX out panel connector) of the
DMX line.
Photo 2Photo 1 Photo 3
5
3
4 2
1
1=GND
2=DATA3=DATA+
CONTROLLER
STA N D A R D
DM X 5 1 2
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
9
XM 2500 SPOT
Page 10
DMX Addresses
XM2500 can be used in two different modes: 30 or 18 DMX channels.
If you want to use the XM2500 in 18 channels mode, select the 18 CH mode from the MODE menu and
set the following addresses on the mixer:
Projector 1 A001
Projector 2 A019 If you want to select the next projector, just add “18”
Projector 3 A037
….. A….
projector 6 A073
If you want to use the XM2500 in 30 channels mode, select the 30 CH mode from the MODE menu and
set the following addresses:
Projector 1 A001
Projector 2 A031 If you want to select the next projector, just add “30”
Projector 3 A061
….. A….
Projector 6 A151
Changing the DMX address
1) Press the UP-DOWN key until you reach the required DMX number. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.
Pushing UP and DOWN keys together,will set the DMX address to channel 001.
ARC 1200
10
XM 2500 SPOT
Page 11
DMX IN
DMX OUT
DISPLAY
MAINS
190-245V ~ 50-60 Hz
8- DISPLAY FUNCTIONS
ARC 1200
11
MENU
ENTER
DOWN
UP
DISPLAY FUNCTIONS
The XM2500 display panel shows all the available functions . Using these functions, it is possible
to change some of the parameters and add some functions. Changing the D.T.S. setting can vary
the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully
follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
Up-DownMENU ENTERUp-Down
PAN MOVEMENT INVERSION
To reverse Pan movement from left
to right and vice versa on DMX
level variation.
Up-Down
Counterclockwise
Clockwise
Up-DownMENU ENTERUp-Down
TILT MOVEMENT INVERSION
To reverse Tilt movement from
bottom upwards and vice versa on
DMX level variation
Up-Down
Up-Down
MENU
ENTERUp-Down
REVERSE DISPLAY
Reverses display's reading depending on
the mounting position
(On the ground or suspended).
Up-Down
Floor
position
Counterclockwise
Clockwise
Suspension
position
Up-DownMENU ENTER
DMX MODE
To select DMX mode : 30-18
channels
30 CHANNELS (Pan & Tilt 16 bit)
18 CHANNELS (Pan & Tilt 16 bit)
Up-Down
Up-Down
Up-DownENTER
Up-DownENTER
DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.
Display OFF
Display
always ON
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
XM 2500 SPOT
Page 12
MENU ENTER
TEST MODE
Full test and single function test.
Up-Down
ARC 1200
12
Up-Down
LAMP
Lamp always ON-always OFF
Or lamp ON-OFF selectable via DMX
ENTER
FORCED ON
ENTER
FORCED OFF
ENTER
ON / OFF VIA DMX (default)
MENU
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ADJUST
To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT-FOCUS and ZOOM
ENTER
Up-Down
ENTER
SENS
To set ON-OFF the electronic lamp sensor
ACC
Lamp strikes counter
MENU ENTER
Up-Down
RESET
Al motors reset
MENU ENTER
DEFAULT
To restore default setting
ENTER
Up-Down
Up-Down
RESET ENABLED VIA DMX
RESET DISABLED VIA DMX
RESET ALL MOTORS
MENU ENTER
Fan control
To control the fan speed .
Up-Down
ENTER
Up-Down
(DEFAULT : 30 )
MENU ENTER
Up-Down
ENTER
ENTER
Up-Down
(DEFAULT : 2 )
SPEED control
Pan Tilt Speed control.
ENTER
Up-Down
8- DISPLAY FUNCTIONS
PAN
TILT
DIMMER
SHUTTER
IRIS
GOBO1
GOBO1 ROT.
GOBO1 SHAKE
GOBO2
GOBO2 ROT.
GOBO2 SHAKE
EFFECTS
EFFECTS ROT.
CYAN
MAGENTA
YELLOW
COLOR
FOCUS
ZOOM
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
XM 2500 SPOT
Page 13
MENU
SOFTWARE VERSION
Electronic cards software version.
Up-Down
PAN-TILT SOFTWARE (PAN-TILT PCB)
ENTER
Up-Down
.
.
.
DISPLAY SOFTWARE (8 MOT PCB N°2)
HEAD MOT. SOFTWARE (8 MOT PC N°1)
MENU
Up-Down
ENTER
TEMPERATURE
Head electronic thermic sensor
MENU
Up-Down
ENTER
AUTO FOCUS
Automatic focusing
.
Up-Down
AUTOMATIC FOCUS DISABLE
AUTOMATIC FOCUS ENABLE
MENU
Up-Down
ENTER
GOBO ROTATION
GOBO ROTATION during gobo scrolling
Up-Down
GOBO ROTATION DISABLE
GOBO ROTATION ENABLE
.
MENU
Up-Down
ENTER
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
Up-Down
ENTER
.
Up-Down
ENTER
Up-Down
ENTER
ENTER
Up-Down
ENTER
ENTER
Up-Down
ENTER
Up-Down
.
ENTER
ENTER
ENTER
Up-Down
ENTER
ENTER
ENTER
Up-Down
.
.
ENTER
PAN LOCK
LOCK THE PAN TO THE DESIRED VALUE
TILT LOCK
LOCK THE TILT TO THE DESIRED VALUE
PAN FREE
REMOVE POWER TO PAN MOTOR
TILT FREE
REMOVE POWER TO TILT MOTOR
MENU ENTER
TIMER
lamp life TIME (reset possible)
and total UNIT LIFE TIME (reset not possible)
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ENTER
ARC 1200
13
8- DISPLAY FUNCTIONS
ENTER
ENTER
ENTER
ENTER
XM 2500 SPOT
Page 14
ARC 1200
14
ERROR: ENCODER PAN
ERROR: ENCODER TILT
ERROR: DMX ADDRESS
ERROR: AUTO MODE INPUT
ERROR: EEPROM DATA LOADER
ERROR: RESET CIRCUIT LINE1 (CMY)
ERROR: RESET CIRCUIT LINE2 (GOBO1 , COLOR)
ERROR: RESET CIRCUIT LINE3 (GOBO2 , FOCUS , ZOOM)
ERROR: RESET CIRCUIT LINE4 (EFFECTS , IRIS)
ERROR: MAGENTA POSITION
ERROR: CYAN POSITION
ERROR: YELLOW POSITION
ERROR: GOBO1 POSITION
ERROR: GOBO1 INDEX POSITION
ERROR: COLOUR WHEEL POSITION
ERROR: GOBO2 POSITION
ERROR: GOBO2 INDEX POSITION
ERROR: ZOOM POSITION
ERROR: FOCUS POSITION
ERROR: EFFECT WHEEL POSITION
ERROR: EFFECT INDEX POSITION
ERROR: IRIS POSITION
9- ERROR MESSAGES
XM 2500 SPOT
Page 15
ARC 1200
15
Up-DownENTER
PAN ALIGNMENT
To align pan position
ES.
ENTER
Up-DownENTER
TILT ALIGNMENT
To align tilt position
ES.
ENTER
Up-Down
Up-Down
ENTER
Up-DownENTERUp-Down
GOBO 1 ALIGNMENT
To align gobo wheel 1
ES.
ENTER
Up-DownENTER
Up-Down
GOBO 1 INDEX ALIGNMENT
To align gobo wheel 1 index
ES.
ENTER
Up-DownENTERUp-Down
GOBO 2 ALIGNMENT
To align gobo wheel 2
ES.
ENTER
Up-DownENTERUp-Down
GOBO 2 INDEX ALIGNMENT
To align gobo wheel 2 index
ES.
ENTER
Up-DownENTERUp-Down
COLOR ALIGNMENT
To align color wheel
ES.
ENTER
Up-DownENTERUp-Down
SHUTTER ALIGNMENT
To align shutter
ES.
ENTER
Up-DownENTERUp-Down
FOCUS ALIGNMENT
To align focus
ES.
ENTER
10- HIDDEN MENU
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
- Reset the XM2500 (reset from the MENU, not from the DMX controller!).
- While reset is running, press the MENU and ENTER keys at the same time.
Electronic calibration of the motors.
Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must
repeat all previous calibrations)
Exit from hidden menu.
XM 2500 SPOT
Page 16
Up-DownENTER
ZOOM ALIGNMENT
To align zoom
ES.
ENTER
Up-DownENTER
EFFECTS ALIGNMENT
To align effects wheel
ES.
ENTER
Up-Down
Up-Down
ENTER
Up-DownENTERUp-Down
EFFECTS INDEX ALIGNMENT
To align effects wheel index
ES.
ENTER
Up-DownENTER
Up-Down
IRIS ALIGNMENT
To align iris
ES.
ENTER
Up-DownENTERUp-Down
CYAN ALIGNMENT
To align cyan
ES.
ENTER
Up-DownENTERUp-Down
MAGENTA ALIGNMENT
To align magenta
ES.
ENTER
Up-DownENTERUp-Down
YELLOW ALIGNMENT
To align yellow
ES.
ENTER
ARC 1200
16
XM 2500 SPOT
Page 17
17
11- Opening up the projector housing
It is possible to inspect the inside of the projector by removing the cover as indicated below.
Attention
REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.
1) Loosen the screws which fix the side covers (photo 1 and 2) .
2) Once unscrewed, simply lift the covers to access the internal components (photo 3).
12- Replacing gobos
XM2500 uses a mechanical system which allows the fixture's gobos to be removed without the use
of special tools. Replacement gobos should be made of either heat resistant glass or metal.
An ever-increasing range of gobos is available from your D.T.S. sales network.
Gobo dimensions are as follows:
ø external = 37 mm
ø of image with defined edge = 32 mm
thickness = from 0.2 to 3.5 mm (see catalogue)
Replacing gobos on the rotating gobo wheels
When replacing gobos, ensure that the projector is switched off.
1) Open the projector housing as described above.
2) Remove the gobo holder to allow easier access to the gobo (photo 1-2).
3) Release the gobo retaining spring and carefully remove the gobo (photo 3).
4) Reverse the procedure to install a replacement gobo.
Photo 1 (gobo wheel 1)
Photo 2 (gobo wheel 2)
Photo 3
Photo 1
Photo 2 Photo 3
XM 2500 SPOT
Page 18
13 Periodic cleaning
Lenses and reflectors
Even a fine layer of dust can reduce the luminous output substantially. Regularly clean all lenses
and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning
will depend, of course, on the conditions in which the projector is operating. Suitable instruments for
performing this type of maintenance are a brush and a common vacuum cleaner or an air
compressor. If necessary, clean the fans and air passages more frequently.
Periodic controls
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will
help to avoid the danger of the lamp exploding.
Mechanical parts
Periodically check all mechanical parts, gears, guides, belts, etc.for wear and tear, replacing them if
necessary. Periodically check the lubrication of all components, particularly the parts subject to
high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.
distributor. Check the tension of the belts and adjust it if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors,
refastening if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the XM2500.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.
Attention
Disconnect mains power prior to removing the projector housing.
ARC 1200
18
XM 2500 SPOT
Page 19
Gobo1 (line 2)
(BLACK)
Gobo1 Rot.
(DARK GREEN)
Strobe
Yellow (line 1)
(PINK)
Colours (line 2)
(LIGHT BLUE)
Cyan (Line 1)
(GOLD)
Magnetic
Sensors
Fans
14- CONTROL MOTORS CAR
+
-
(Line 1)
Line 1 Brown
Line 2 Orange
Magenta (line 1)
(BLUE)
GND
ORANGE
BROWN
VCC
J5 FROM
J10 PAN & TILT
(YELLOW)
Display
30 VDC
J3 FROM
J8 PAN & TILT
TEMP
GND
LIGHT
GND
Free
Electronic
sensors
lamp&temp
J9 FROM
J2 TCN0108
ARC 1200
19
8 MOTORS PCB “1
XM 2500 SPOT
Page 20
Gobo2 (line 1)
(BLACK)
Gobo2 Rot.
(DARK GREEN)
Free
Effects (line 2)
(PINK)
Iris (line 2)
(GREY)
Zoom (line 1)
(LIGHT BLUE)
Effects Rot. (Line 2)
(GOLD)
Magnetic
Sensors
J3 FROM
J8 PAN & TILT
FANS
30 VDC
+
-
(Line 1)
Line 1 Brown
Line 2 Orange
Focus (line 1)
(BLUE)
GND
ORANGE
BROWN
VCC
J5 FROM
J10 PAN & TILT
ARC 1200
20
8 MOTORS PCB “2”
14- CONTROL MOTORS CAR
XM 2500 SPOT
Page 21
ARC 1200
21
BLACK RED
BLACK BLACK
FROM J4
8 MOTORS CARD
15-DISPLAY CARD
J2
J3
J4
PAN
(WHITE)
TILT
(BROWN)
GND
(BLACK)
30 VDC
(RED)
FAN
(B/W)
DMX IMPUT
(WHITE)
FROM J3
8 MOTORS
(VIOLET)
FROM J5
8 MOTORS
(LIGHT GREEN)
ENCODER TILT
(ORANGE)
ENCODER PAN
(RED)
16-PAN & TILT CARD
17-LAMP ON-OFF CONTROL CARD
FROM J9
8 MOT CONT.
CARD 1
TO J9
ELECTRONIC
BALLAST
DATA1
VILOET
DATA2
LIGHT GREEN
TILT MOTOR
BROWN
TILT
ENCODER
ORANGE
DISPLAY
DATA1
BLACK
DISPLAY
DATA1
BLACK-BLACK
LAMP ON-OFF
DATA
RED
18-CABLES RESEND CARD
XM 2500 SPOT
Page 22
18 CHANNELS MODE
1 PAN msb 540°
2 PAN lsb
3 TILT msb 270°
4 TILT lsb
5 DIMMER
6 SHUTTER
7 COLOUR
8 COLOUR MACROS
9 GOBO 1
10 GOBO 1 ROTATION/INDEX
11 GOBO 2
12 GOBO 2 ROTATION/INDEX
13 IRIS
14 EFFECTS
15 EFFECTS ROTATION
16 FOCUS
17 ZOOM
18 LAMP ON/OFF - RESET
19- DMX PROTOCOL
DMX CHANNEL
1
Parameter: PAN msb
DMX CHANNEL
2
Parameter: PAN lsb
DMX CHANNEL
3
Parameter: TILT msb
DMX CHANNEL
4
Parameter: TILT lsb
DMX CHANNEL 5
Parameter: DIMMER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
ARC 1200
22
0-7
Black-out
8-255
Proportional dimmer from Closed to Open
XM 2500 SPOT
Page 23
DMX CHANNEL 7
Parameter: COLOUR
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-10
5
Colour1
11-21
16
Bicolour ½
22-32
27
Colour2
33-43
38
Bicolour 2/3
44-54
49
Colour3
55-65
60
Bicolour 3/4
66-76
71
Colour4
77-87
82
Bicolour 4/5
88-98
93
Colour5
99-109
104
Bicolour 5/6
110-120
115
Colour6
121-131
126
Bicolour 6/7
132-142
137
Colour7
143-153
148
Bicolour 7/8
154-164
159
Colour8
ARC 1200
23
DMX CHANNEL
6
Parameter: SHUTTER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-19
Black-out
20-39
Open
60-79
Strobe speed 1 min.
80-89
Strobe speed 2
100-109
Strobe speed 3
110-119
Strobe speed 4
130-139
Strobe speed 5
140-149
Strobe speed 6 max.
150-159
Pulse open speed 1 min.
160-169
Pulse open speed 2
170-179
Pulse open speed 3
180-189
Pulse open speed 4 max.
190-199
Pulse closed speed 1 min.
200-209
Pulse closed speed 2
210-219
Pulse closed speed 3
220-227
Pulse closed speed 4 max.
228-233
Colour and Gobo in black-out
234-255
Pan and Tilt in black-out
Open
40-59
Black-out
120-129
Random Strobe
90-99
XM 2500 SPOT
Page 24
165-175
170
Bicolour 8/9
176-186
181
Colour9
187-197
192
Bicolour 9/1
198-200
199
Right rotation speed 1 max.
201-203
200
Right rotation speed 2
204-206
205
Right rotation speed 3
207-209
208
Right rotation speed 4
210-212
211
Right rotation speed 5
213-215
214
Right rotation speed 6
216-218
217
Right rotation speed 7
219-221
220
Right rotation speed 8
222-224
223
Right rotation speed 9 min.
225-228
226
Stop
229-231
230
Left rotation speed 1 min.
232-234
233
Left rotation speed 2
235-237
236
Left rotation speed 3
238-240
239
Left rotation speed 4
241-243
242
Left rotation speed 5
244-246
245
Left rotation speed 6
247-249
248
Left rotation speed 7
250-252
251
Left rotation speed 8
253-255
254
Left rotation speed 9 max.
DMX CHANNEL 8
Parameter: COLOUR MACROS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
No Effect
Macro 1
Macro 2
Macro3
Macro 4
Macro 5
Macro 6
ARC 1200
24
DMX CHANNEL 7
Parameter: COLOUR
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-35
36-71
72
-107
108-143
144-179
180-215
216-255
18
52
90
126
160
198
232
XM 2500 SPOT
Page 25
DMX CHANNEL 9
Parameter: GOBO 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-29
15
Open
30-59
45
Gobo 1
60-89
75
Gobo 2
90-119
105
Gobo 3
120-149
135
Gobo 4
150-179
165
Gobo 5
180-207
168
Gobo 6
208-213
210
Speed rotation 1 min.
214-219
216
Speed rotation 2
220-225
222
Speed rotation 3
226-231
228
Speed rotation 4
232-237
234
Speed rotation 5
238-243
240
Speed rotation 6
244-249
246
Speed rotation 7
250-255 252 Speed rotation 8 max.
DMX CHANNEL
10
Parameter: GOBO 1 ROTATION/INDEX
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-127
Index 0° - 360°
128-185
Left rotation from fast to slow
186-197
Stop
198-255
Right rotation from slow to fast
ARC 1200
25
DMX CHANNEL 11
Parameter: GOBO 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-29
15
Open
30-59
45
Gobo 1
60-89
75
Gobo 2
90-119
105
Gobo 3
120-149
135
Gobo 4
150-179
165
Gobo 5
180-207
168
Gobo 6
208-213
210
Speed rotation 1 min.
214-219
216
Speed rotation 2
220-225
222
Speed rotation 3
226-231
228
Speed rotation 4
232-237
234
Speed rotation 5
238-243
240
Speed rotation 6
244-249
246
Speed rotation 7
250-255 252 Speed rotation 8 max.
XM 2500 SPOT
Page 26
DMX CHANNEL 13
Parameter: IRIS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Open
Linear Iris from Open to Closed
Iris pulse at different speeds from Min to Max
Iris closing at different speed from Min to Max
Iris openig at different speed from Min to Max
Closed
DMX CHANNEL 14
Parameter: EFFECTS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-41
No effect
42-83
Effect 1
Effect 3
84-125
126-167
Effect 2
ARC 1200
26
DMX CHANNEL
12
Parameter: GOBO 2 ROTATION/INDEX
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Iris closing combined with Zoom at different speed from Min to Max
Iris openig combined with Zoom at different speed from Min to Max
Effect 5
168-209
210-255
Effect 4
DMX CHANNEL 15
Parameter: EFFECTS ROTATION/INDEX
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-127
Index 0°- 360°
128-180
Left rotation from Max to Min
Right rotation from Min to Max
181-202
203-255
Stop
0-127
128-185
186-197
198-255
Index 0° - 360°
Left rotation from fast to slow
Stop
Right rotation from slow to fast
0-9
10-124
125-132
133-159
160-186
187-214
215-234
215-234
XM 2500 SPOT
Page 27
DMX CHANNEL 16
Parameter: FOCUS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255
Linear Focus
DMX CHANNEL
17
Parameter: ZOOM
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255
Linear Zoom
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
DMX CHANNEL 18
Parameter: RESET
0-9
No Effect
10-60 Lamp OFF (activ.after 3 seconds)
61-129
130-179
Internal motor reset
Total Reset
180-200
201-239
240-255
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
ARC 1200
27
XM 2500 SPOT
Page 28
30 CHANNELS MODE (DEFAULT)
1 PAN msb 540°
2 PAN lsb
3 TILT msb 270°
4 TILT lsb
5 SPEED MOVEMENT
6 DIMMER
7 SHUTTER
8 COLOUR
9 COLOUR MODE
10 CYAN
11 MAGENTA
12 YELLOW
13 COLOUR MACROS
12 GOBO 1
15 GOBO 1 MODE
16 GOBO 1 ROTATION/INDEX COARSE
17 GOBO 1 INDEX FINE 16 bit
18 GOBO 1 SHAKE
19 GOBO 2
20 GOBO 2 MODE
21 GOBO 2 ROTATION/INDEX COARSE
22 GOBO 2 INDEX FINE 16 bit
23 GOBO 2 SHAKE
24 IRIS
25 IRIS MACROS
26 EFFECTS
27 EFFECTS ROTATION
28 FOCUS
29 ZOOM
30 LAMP ON/OFF - RESET
DMX CHANNEL
1
Parameter: PAN msb
DMX CHANNEL
2
Parameter: PAN lsb
DMX CHANNEL
3
Parameter: TILT msb
DMX CHANNEL
4
Parameter: TILT lsb
DMX CHANNEL
5
Parameter: SPEED MOVEMENT
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-10
5
Standard
11-25
18
Fast movement
26-127
Vector mode from fast to slow
128-247
Variable time reaction to
DMX signal ( fast to slow)
248-255
251
Slow reaction time to DMX
signal
ARC 1200
28
XM 2500 SPOT
Page 29
DMX CHANNEL 6
Parameter: DIMMER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-8
4
Black-out
9-255
Proportional dimmer
DMX CHANNEL
7
Parameter: SHUTTER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-19
Black-out
20-39
Open
60-79
Strobe speed 1 min.
80-89
Strobe speed 2
100-109
Strobe speed 3
110-119
Strobe speed 4
130-139
Strobe speed 5
140-149
Strobe speed 6 max.
150-159
Pulse open speed 1 min.
160-169
Pulse open speed 2
170-179
Pulse open speed 3
180-189
Pulse open speed 4 max.
190-199
Pulse closed speed 1 min.
200-209
Pulse closed speed 2
210-219
Pulse closed speed 3
220-227
Pulse closed speed 4 max.
228-233
Colour and Gobo in black-out
234-255
Pan and Tilt in black-out
Open
40-59
Black-out
120-129
Random Strobe
90-99
DMX CHANNEL 8
Parameter: COLOUR
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-27
28-55
56-83
84-111
112-139
IF CHANNEL 9 = FULL COLOUR (Dmx range value 0 - 63)
140-167
168-195
224-255
196-223
Colour1
Colour3
Colour2
Colour4
Colour5
Colour6
Colour7
Colour8
Colour9
29
XM 2500 SPOT
Page 30
DMX CHANNEL 8
Parameter: COLOUR 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-25
26-51
52-77
78-103
104-129
IF CHANNEL 9 = HALF COLOUR (Dmx range value 64 - 127)
130-155
156-181
208-233
182-207
234-255
Bicolour ½
Bicolour 2/3
Bicolour 3/4
Bicolour 4/5
Bicolour 5/6
Bicolour 6/7
Bicolour 7/8
No Colour
Bicolour 8/9
Bicolour 9/1
0-10
11-255
IF CHANNEL 9 = PROPORTIONAL COLOUR (Dmx range value 128 - 191)
Proportional colour
No Colour
IF CHANNEL 9 = RAINBOW (Dmx range value 192 - 255)
0-9
10-127
Right Rot.Speed from Max to Min
No Colour
128-137
138-255
Left Rot.speed from Min to Max
Stop
DMX CHANNEL 9
Parameter: COLOUR MODE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-63
64-127
Half Colour
Full Colour
128-191
192-255
Rainbow
Proportional Colour
30
DMX CHANNEL 10
Parameter: CYAN
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255
Proportional Colour
DMX CHANNEL 11
Parameter: MAGENTA
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255
Proportional Colour
XM 2500 SPOT
Page 31
DMX CHANNEL 12
Parameter: YELLOW
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255
Proportional Colour
31
DMX CHANNEL 13
Parameter: COLOUR MACROS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-9
5
No Effect
10-44
28
Macro 1
45-79
64
Macro 2
80-114
96
Macro3
115-149
134
Macro 4
150-184
168
Macro 5
185-219
204
Macro 6
220-255
238
Macro 7
DMX CHANNEL 14
Parameter: GOBO 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-29
15
Open
30-59
45
Gobo 1
60-89
75
Gobo 2
90-119
105
Gobo 3
120-149
135
Gobo 4
150-179
165
Gobo 5
180-207
168
Gobo 6
208-213
210
Speed rotation 1 min.
214-219
216
Speed rotation 2
220-225
222
Speed rotation 3
226-231
228
Speed rotation 4
232-237
234
Speed rotation 5
238-243
240
Speed rotation 6
244-249
246
Speed rotation 7
250-255 252 Speed rotation 8 max.
DMX CHANNEL
15
Parameter: GOBO 1 MODE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-127
Gobo Rotation Mode
128-255
Gobo Index Mode
-
XM 2500 SPOT
Page 32
DMX CHANNEL 16
Parameter: GOBO 1 ROTATION/GOBO 1 INDEX COARSE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-9
10-127
128-137
138-255
IF CHANNEL 15 = Gobo Rotation Mode (Dmx range value 0 - 127)
Right Rot. Prop. Speed Max to Min
Stop
Left Rot. Prop. Speed Min to Max
Stop
0-255
IF CHANNEL 15 = Gobo Index Mode (Dmx range value 128 - 255)
Gobo index Coarse
DMX CHANNEL
17
Parameter: GOBO 1 INDEX FINE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Gobo Index Fine
0-255
DMX CHANNEL
18
Parameter: GOBO 1 SHAKE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Stop
0-9
10-22
23-35
36-48
Gobo Shake R-L Speed 1 Min.
Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
49-61
62-74
75-87
88-100
101-113
114-126
127-138
139-151
Gobo Shake R-L Speed 4
Gobo Shake R-L Speed 5
Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7
Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2
Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4
Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
152-164
165-177
178-190
191-203
204-216
217-229
230-242
243-255
Gobo Shake L-R Speed 9 Max
32
XM 2500 SPOT
Page 33
DMX CHANNEL 19
Parameter: GOBO 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-29
15
Open
30-59
45
Gobo 1
60-89
75
Gobo 2
90-119
105
Gobo 3
120-149
135
Gobo 4
150-179
165
Gobo 5
180-207
168
Gobo 6
208-213
210
Speed rotation 1 min.
214-219
216
Speed rotation 2
220-225
222
Speed rotation 3
226-231
228
Speed rotation 4
232-237
234
Speed rotation 5
238-243
240
Speed rotation 6
244-249
246
Speed rotation 7
250-255 252 Speed rotation 8 max.
DMX CHANNEL
20
Parameter: GOBO 2 MODE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-127
Gobo Rotation Mode
128-255
Gobo Index Mode
-
DMX CHANNEL 21
Parameter: GOBO 2 ROTATION/GOBO 2 INDEX COARSE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-9
10-127
128-137
138-255
IF CHANNEL 20 = Gobo Rotation Mode (Dmx range value 0 - 127)
Right Rot. Prop. Speed Max to Min
Stop
Left Rot. Prop. Speed Min to Max
Stop
0-255
IF CHANNEL 20 = Gobo Index Mode (Dmx range value 128 - 255)
Gobo index Coarse
DMX CHANNEL
22
Parameter: GOBO 2 INDEX FINE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Gobo Index Fine
0-255
33
XM 2500 SPOT
Page 34
DMX CHANNEL
23
Parameter: GOBO 2 SHAKE
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
Stop
0-9
10-22
23-35
36-48
Gobo Shake R-L Speed 1 Min.
Gobo Shake R-L Speed 2
Gobo Shake R-L Speed 3
49-61
62-74
75-87
88-100
101-113
114-126
127-138
139-151
Gobo Shake R-L Speed 4
Gobo Shake R-L Speed 5
Gobo Shake R-L Speed 6
Gobo Shake R-L Speed 7
Gobo Shake R-L Speed 8
Gobo Shake R-L Speed 9 Max
Stop
Gobo Shake L-R Speed 1 Min
Gobo Shake L-R Speed 2
Gobo Shake L-R Speed 3
Gobo Shake L-R Speed 4
Gobo Shake L-R Speed 5
Gobo Shake L-R Speed 6
Gobo Shake L-R Speed 7
Gobo Shake L-R Speed 8
152-164
165-177
178-190
191-203
204-216
217-229
230-242
243-255
Gobo Shake L-R Speed 9 Max
DMX CHANNEL 24
Parameter: IRIS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-9
Closed
Iris pulse at different speeds from Max to Min
Iris pulse with flash closing from Min to Max
Iris pulse with flash opening from Min to Max
DMX CHANNEL 25
Parameter: IRIS MACROS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
No effect
0-9
10-63
64-117
118-171
34
10-246
Linear Iris from Open to Closed
247-255
Open
Iris pulse with flash closing combined with Zoom from Min to Max
172-213
214-255
Iris pulse with flash opening combined with Zoom from Min to Max
XM 2500 SPOT
Page 35
DMX CHANNEL 26
Parameter: EFFECTS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-41
No effect
42-83
Effect 1
Effect 3
84-125
126-167
Effect 2
Effect 5
168-209
219-255
Effect 4
DMX CHANNEL 27
Parameter: EFFECTS ROTATION/INDEX
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-127
Index 0°- 360°
128-180
Left rotation from Min to Max
Right rotation from Min to Max
181-202
203-255
Stop
DMX CHANNEL 28
Parameter: FOCUS
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255
Linear Focus
DMX CHANNEL
29
Parameter: ZOOM
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255
Linear Zoom
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
DMX CHANNEL 30
Parameter: RESET
0-9
No Effect
10-60 Lamp OFF (activ.after 3 seconds)
61-129
130-179
Internal motor reset
Total Reset
180-200
201-239
240-255
No Effect
Lamp ON (activ.after 3 seconds)
No Effect
35
XM 2500 SPOT
Page 36
The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from D.T.S. D.T.S. reserves the right to make any aesthetic, functional or design modifications to
any of its products without prior notice. D.T.S. assumes no responsibility for the use or application
of the products or circuits described herein.
MADE IN ITALY
D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy
Tel. +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it www.dts-lighting.it
Loading...