DTS Wonder D, Wonder S User Manual

Page 1
D.T.S. Illuminazione s.r.l.
Via Fagnano Selve 10/12/14 47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it http://www.dts-lighting.it
Made in Italy
Page 2
2
Le informazioni contenute in questo documento sono state attentamente redatte e
controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.
Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,
riprodotto per intero o in parte senza previo consenso scritto della D.T.S .
D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche
estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna
responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are
reserved and this document cannot be copied, photocopied or reproduced, in part or
completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to
any of its products without prior notice. D.T.S. assumes no responsibility for the use or
application of the products or circuits described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées
avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas
d'éventuelles inexactitudes. Tous droits réservés. Ce document ne peut être copié,
photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement
préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,
fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline
toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits
décrits.
Las informaciones contenidas en este documento han sido cuidadosamente
redactadas y controladas. Con todo, no se asume ninguna responsabilidad por
eventuales inexactitudes. Todos los derechos han sido reservados y este documento
no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa
autorización escrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de
carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume
responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los
productos o de los circuitos descritos.
Page 3
3
INDEX:
1 - SYMBOLS........................................................................................................................... 4
2 - GENERAL WARNING......................................................................................................... 5
3 - GENERAL WARRANTY CONDITIONS .............................................................................. 5
4 - TECHNICAL FEATURES .................................................................................................... 5
5 - ACCESSORIES .................................................................................................................. 7
6 - IMPORTANT SAFETY INFORMATION .............................................................................. 8
6.1 Fire prevention ............................................................................................................... 8
6.2 Prevention of electric shock ........................................................................................... 8
6.3 Safety ............................................................................................................................ 8
6.4 Level of protection against the penetration of solid and liquid objects ............................ 8
6.5 Long-life auto-charging buffer battery ............................................................................ 8
7 - VOLTAGE AND FREQUENCY ........................................................................................... 9
8 - INSTALLATION .................................................................................................................. 9
8.1 Safety cable ................................................................................................................. 10
8.2 Protection against liquids ............................................................................................. 10
8.3 Movement .................................................................................................................... 11
8.4 Risk of fire .................................................................................................................... 11
8.5 Forced ventilation ........................................................................................................ 11
8.6 Ambient temperature ................................................................................................... 11
9 - MAINS CONNECTION ...................................................................................................... 12
9.1 Protection .................................................................................................................... 12
10 - DMX SIGNAL CONNECTION ......................................................................................... 13
10.1 DMX addresses ....................................................................................................... 13
10.2 Selecting the DMX address ...................................................................................... 13
11 - FIRMWARE UPDATING ................................................................................................ 14
12 - DISPLAY FUNCTIONS .................................................................................................. 15
13 - PERIODIC CLEANING .................................................................................................... 19
13.1 Front lenses screen glass ........................................................................................ 19
13.2 Fans and air passages ............................................................................................. 19
14 - PERIODIC CONTROLS ................................................................................................. 19
15 - DMX PROTOCOL ........................................................................................................... 21
Page 4
4
1- SYMBOLS
Graphic symbols used on this manual:
THIS SYMBOL INDICATES A HOT SURFACE
Never handle the unit until at least 10 minutes have
elapsed since the projector was turned off.
THIS SYMBOL INDICATES TEMPERATURE OF THE EXTERNAL SURFACE
The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is 80°C (176°F).
THIS SYMBOL INDICATES THE ELECTRIC SHOCK RISK
High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head.
THIS SYMBOL INDICATES PROTECTION AGAINST ELECTRICAL SHOCK Connection must be made to a power supply system fitted with efficient earthing (Class I appliance).
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS YOU CAN PLACE THE
UNIT ON NORMALLY FLAMMABLE SURFACES
Suitable for mounting on normally flammable
materials surfaces greater than 200°C with
some combustion time lag.
THIS SYMBOL MEANS PHOTOBIOLOGICAL SAFETY
Caution: Possibly hazardous optical radiation emitted from this product. Do not stare at operating light
source. May be harmful to the eyes.
THIS SYMBOL INDICATES THE MINIMUM
DISTANCE FROM ILLUMINATED OBJECTS
LONG-LIFE AUTO-CHARGING BUFFER BATTERY The projector contains a rechargeable lead-acid or
lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.
!
Page 5
5
2- GENERAL WARNING Read the instruction contained in this user manual carefully, as they give important
information regarding safety during installation, use and maintenance. The device is not for domestic use and must be installed by a qualified electrician or experienced person. Always disconnect the device from the mains before maintenance. The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 36 months from the date of purchase against manufacturing material defects.
4- TECHNICAL FEATURES
Overview WONDER S introduces a revolutionary fixture architecture: an exclusive optical
system consisting of two concentric zones, each featuring a different type of lenses. This new technology achieves an unprecendeted result: the brightest most uniform wall wash ever seen. In traditional wash lights, in fact, when the beam is widened to illuminate a larger area, a darker spot is visible in the center. The exclusive optics of the WONDER S, however lets you balance the brightness of the entire beam with that of its center, resulting in unparalleled evenly diffused luminosity. You can also obtain stunning multicolor projections: WONDER S LED board consists of four independent zones: a central one, and a ring divided into three distinct sections. Each of these four areas has individual control of luminosity, colors and effects: it’s like having four LED fixtures in one.
The unit is also available as WONDER D, offering an exclusive double concentric optical system featuring different lenses and linear zoom ranges (central: 3.5° - 52° zoom; ring: 8° - 52° zoom). This revolutionary configuration results in an unprecendented evenly diffused luminosity, size and color. WONDER D can create amazing concentric multi-color beams and effects in the air, guaranteed to astonish any audience. Also, WONDER D comes equipped with the
‘FPR’ system (D.T.S. patent), which allows limitless pan rotation, in either direction,
never having to reverse motion.
WONDER S FC
(D.T.S. Product Code: 03.LDR014.F)
• Electronic ballast 90-260Vac 50-60 Hz Black finish WONDER D FPR FC
(D.T.S. Product Code: 03.LDR013.FFP)
• Electronic ballast 90-260Vac 50-60 Hz • FPR (Free Pan Rotation) • Black finish
Page 6
6
4- TECHNICAL FEATURES
LED Technology 49 FULL COLOUR LEDs (RGBW)
Optical group
WONDER S: 7 x 3.5° lenses; 42 x 8° lenses
3.5° - 52° long excursion high-efficiency linear motorized zoom
22.000 Lux / 5 m WONDER D: 2 concentric independent high efficiency optical groups Optical group 1 (7 lenses): 3.5° - 52° long excursion linear motorized zoom Optical group 2 (42 lenses): 8°- 52° long excursion linear motorized zoom
22.000 Lux / 5 m Color generation
4 discrete LED areas; each area is independently controllable (luminosity, colors, effects) 16 million colors each Wide palette of pure uniform whites with variable linear color temperature (2700K – 8000K)
Interface / Control / Programming LCD graphic display + 4 soft-keys (control / management of the main parameters) Long-life auto-charging buffer battery RDM ARTNET ready Wireless ready Updatable internal operating system Li-Fe display backup battery (WONDER D)
DMX channels 34 ch (Default) or 38 ch
Pan & Tilt
WONDER S: Pan 540°: 2.5 sec.; Tilt 270°: 1.5 sec WONDER D: ‘FPR’ system (D.T.S. patent) Pan: limitless rotation, in both directions; 360° rotation in 1.56 sec.; Tilt 270°: 1.5 sec. Tri-phase stepper motor technology for ultra-fast silent movements 16-bit resolution Selectable speed ranges Pan / Tilt lock
Power supply Electronic full-range 90-260Vac 50-60 Hz Power consumption: 850W
Connection DMX: 4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik Power supply: POWERCON IN and OUT (re-launch) connectors by Neutrik
Page 7
7
Operating ambient temperature
-10° / 40° Weight
22 Kg International certifications
Certification CE; LED Class: Class 2 LED product
DIMENSIONS
Packaging Dimensions (LxWxH) 610 x 410 x 695 mm Weight: 27 Kg
5- ACCESSORIES
As standard
* 1 x POWERCON male cable connector (Code 0520P014) * 1 x XLR 5 Pins male cable connector (Code 0508B066) * 1 x XLR 5 Pins female cable connector (Code 0508B065) * 2 x Omega clamp with “Fast Lock” connection 1/4 turn (Code 02K00549) * User’s manual
Optional (on request)
• “C” Clamp G100 black / professional (max. load 200Kg) (Code 0521A015)
• Aliscaf Clamp (max. capacity load 100Kg) (Code 0521A008)
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (Code
0521A010)
Page 8
8
6- IMPORTANT SAFETY INFORMATION
6.1 Fire prevention:
-It is permissible to place the unit on normally flammable surfaces. Suitable for mounting on normally flammable materials surfaces greater than 200°C with some combustion time lag.
-Minimum distance from the closest illuminable surface: 0,5 m.
-Replace any blown or damaged fuses only with those of identical value (10AT). Refer to the wiring diagram if there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker. It is, moreover, recommended to protect the supply lines of the projectors from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
6.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head.
-The level of technology inherent in the WONDER requires the assistance of specialised personnel for all servicing. Please refer to an authorised D.T.S. service centre.
-Connection must be made to a power supply system fitted with efficient earthing (Class I appliance).
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
6.3 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.
-The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is 80°C (176°F). Never handle the unit until at least 10 minutes have elapsed since the projector was turned off.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should not exceed 40°C.
-Caution: Possibly hazardous optical radiation emitted from this product. Do not stare at operating light source. May be harmful to the eyes.
6.4 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid objects is IP20.
6.5 Long-life auto-charging buffer battery:
-The projector contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.
!!!
Page 9
9
7- VOLTAGE AND FREQUENCY The WONDER with electronic ballast can operate at 90-260Vac 50-60 Hz.
8- INSTALLATION
WONDER may be either floor or ceiling mounted. For floor mounting installations, the WONDER is supplied with four rubber mounting feet on the base. For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as not to move or shake whilst the WONDER is moving. Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the WONDER by using the two omega clamps (provided in the box) in conjunction with fixing clamps for truss (fixing clamps are not included into the unit box).
Page 10
10
8.1- Safety cable
We recommend the use of a safety cable or chain connected to the WONDER and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable or chain can bear the weight of the entire unit. You may attach the safety chain/cord to the attachment point (A) located on the base of the fixture, as shown in the picture below.
8.2 Protection against liquids
The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur.
!
Page 11
11
8.3- Movement
Unlimited Pan rotation; Tilt 270° (1,5 sec.) . Do not place any obstructions in the path of the projector's movement.
WARNING
Do not place any object in the path of the projector’s movement
Free Pan Rotation (‘FPR’)
8.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. It is permissible to place the unit on normally flammable surfaces. Suitable for
mounting on normally flammable materials surfaces greater than 200°C with some combustion time lag.
Minimum distance from the closest illuminable surface: 0,5 m.
8.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on both the base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in operation. Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
8.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.
!
!
Page 12
12
9- MAINS CONNECTION
WONDER with electronic ballast operates at 90-260V 50-60 Hz. Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 4 amps at 230 VOLT, or 10 amps at 90 VOLT each unit connected. Strict adherence to regulatory norms is strongly recommended.
MAINS AC OUTPUT 90-260V 50/60 Hz (16A Max)
Max 4 WONDER Units @ 230V Max 2 WONDER Units @ 120V
MAINS AC INPUT 90-260V 50/60 Hz
FUSE 10A T
9.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each WONDER. It is, moreover, recommended to protect the supply lines of the projectors by using Appropriately sized residual current devices. Connection must be made to a power supply system fitted with efficient earthing (Class I appliance). A good earth connection is essential for the correct operation of the projector.
!
Page 13
13
10- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy. The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one. This way, all the projectors are cascade connected. NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX terminator. The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor between pin 2 and 3. The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
Page 14
14
10.1-DMX Addresses
WONDER S / WONDER D can be used in 2 different DMX modes: 34 DMX control channels (Default) or 38 DMX control channels. Here below is described the DMX channels addressing for the controller when WONDER is set to 34 and 38 DMX control channels:
34 channels mode (Default) Projector 1 A001 Projector 2 A035 If you want to select the next projector, just add “34” Projector 3 A069 ….. A…. projector 6 A171
38 channels mode Projector 1 A001 Projector 2 A039 If you want to select the next projector, just add “38” Projector 3 A077 ….. A…. projector 6 A191
10.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.
TRICKS: If you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.
11- FIRMWARE UPDATING
To update the software version of the WONDER S / WONDER D you need:
- “D.T.S. Firmware Upgrade Utility” program installed on the PC
- D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008)
- USB-DMX Driver for the D.T.S. RED BOX interface.
- Latest firmware release available for WONDER S / WONDER D unit
Updating the software version.
Please follow the procedure below to perform the update:
1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.
2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
4. Send the new software version into the unit by using “D.T.S Firmware Upgrade Utility” program.
Page 15
15
MENU
ENTER DOWN
UP
DISPLAY
PAN DIRECTION
NORMAL
MENU ENTER DOWN UP
TILT DIRECTION
NORMAL
MENU ENTER DOWN UP
12- DISPLAY FUNCTIONS
DISPLAY FUNCTIONS
The WONDER S / WONDER D display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections. NOTE: the symbol shows which key has to be pushed to obtain the desired function.
Software Version: 10-11-11
Pan Direction PAN DIRECTION
This menu allows to set the Pan movement Normal or Reverse
Tilt Direction
TILT DIRECTION This menu allows to set the Tilt movement Normal or Reverse
Pan Speed
PAN SPEED Pan Speed control (1-8)
Tilt Speed TILT SPEED
Tilt Speed control (1-8)
Up-Down
Menu
Up-DownENTER
Up-Down
Menu
Up-Down
Menu
Up-DownENTER
Up-DownENTER
ENTER
ENTER
ENTER
Up-Down
Menu
Up-DownENTER
ENTER
Pan movement Normal or Reverse Default = Normal
Tilt movement Normal or Reverse Default = Normal
Pan Speed control (1-8) Default = 8 (Live Mode)
Tilt Speed control (1-8) Default = 8 (Live Mode)
MENU ENTER DOWN UP
8
LIVE-TOUR MODE
PAN SPEED
MENU ENTER DOWN UP
8
LIVE-TOUR MODE
TILT SPEED
Page 16
16
MENU ENTER DOWN UP
ENABLED
BY DMX
RESET
MENU ENTER DOWN UP
34 CHANNELS
DMX MODE
12- DISPLAY FUNCTIONS
Display
DISPLAY FLIP / STAND BY / CONTRAST Display Flip:
Reverses display's reading depending on the mounting position (on the ground or suspended).
Display Standby: To turn off the display (after 5 seconds) or leave it always on.
Display Contrast: Display contrast regulation (1-40)
DMX Mode
DMX MODE To select DMX mode: 34 channels (Default) or 38 channels
Reset RESET
Reset via DMX ENABLED / DISABLED and unit motors reset
Wireless
WIRELESS Wireless DMX enabled / disabled.
(Wireless module on request)
Up-Down
Menu
Up-DownENTER
ENTER
ENTER
ENTER
Up-Down
Menu
Up-DownENTER
ENTER
MENU ENTER DOWN UP
FLIP
FLIP
ON THE GROUND
DISPLAY
MENU ENTER DOWN UP
FLIP
STANDBY
OFF
DISPLAY
MENU ENTER DOWN UP
FLIP
CONTRAST
25
DISPLAY
Display Flip ON THE GROUND (Default) SUSPENDED
Display Standby OFF = Display Standby disabled (Default) ON = Display goes OFF after 5 seconds
Display Contrast 1-40 (Default = 25)
Up-Down
Menu
Up-DownENTER
DMX Mode 34 channels (Default) 38 channels
ENTER
ENABLED = Reset via DMX enabled (Default) DISABLED = Reset via DMX disabled NOW = Unit motors reset
Up-Down
Menu
Up-DownENTER
ENTER
ON = Enabled OFF = Disabled (Default) UNLINK = Log out
(Wireless module on request)
WIRELESS
OFF
MENU ENTER DOWN UP
Page 17
17
SMOOTH VALUE Range = 0 – 20 Default = 4
GAMMA CORRECTION LINE = Linear current output QUAD = Quadratic light output (Default)
OUTPUT FREQUENCY Range: 600 Hz – 10 KHz Default = 600 Hz
BOOST OFF = 800mA (Default) ON = 1000mA
SMOOTH
LED
MENU ENTER DOWN UP
4
GAMMA CORR.
LED
MENU ENTER DOWN UP
QUAD
FREQUENCY
LED
MENU ENTER DOWN UP
600 Hz
BOOST
LED
MENU ENTER DOWN UP
OFF
MENU ENTER DOWN UP
LIVE-TOUR
SETTING
LIVE-STUDIO
SYSTEM INFO
UNIT LIFE: 0124H LED: R10 ZOOM: R11 PT: R11 MODEL: WONDER D FPR
MENU ENTER DOWN UP
RDM: 000009B4
12- DISPLAY FUNCTIONS
LED
SMOOTH: This menu allows to select
the value of the delay (in milliseconds) for RGBW and Dimmer channels reaction to DMX or program variation. 4 = 25 ms delay (fast response) 20 = 250 ms delay (slow response)
GAMMA CORRECTION This menu allows to select between Linear current output or Quadratic current output for LEDs.
OUTPUT FREQUENCY This menu allows to adjust the PWM frequency value (Hz) in order to reduce flickering in the process of your camera recordings.
BOOST This menu allows to increase the LEDs current from 800mA to 1000mA.
Live-Studio setting
System Info
Up-Down
Menu
Up-DownENTER
ENTER
SYSTEM INFO Unit life time; LED Driver, Zoom and Pan&Tilt PCBs software version; unit model and RDM ID
Up-Down
Menu
Up-DownENTER
ENTER
Up-Down
Menu
Up-DownENTER
ENTER
LIVE-TOUR mode = High fans speed: the LEDs always work at maximum power (Default)
STUDIO mode = Low fans speed for a very low noise operation
Page 18
18
REBOOT
MENU ENTER DOWN UP
TEMPERATURE
CENTER: 041°C MAX CURR. SECTOR 1: 046°C 1000 MA SECTOR 2: 049°C SECTOR 3: 048°C CPU: 049°C
MENU ENTER DOWN UP
LED LIFE HOURS
CENTER S1 S2 S3 R: 0024 0024 0024 0024 G: 0024 0024 0024 0024 B: 0024 0024 0024 0024 W: 0023 0023 0023 0023
MENU ENTER DOWN UP
12- DISPLAY FUNCTIONS
LED Life hours
Temperature
Reserved
RESERVED
000
MENU ENTER DOWN UP
ENTER CODE
PAN LOCK
NO
MENU ENTER DOWN UP
Up-Down
Menu
Up-DownENTER
ENTER
Pan Lock = Lock the Pan to the desired value Tilt Lock = Lock the Tilt to the desired value Pan Free = Remove power to Pan motor Tilt Free = Remove power to Tilt motor
LOCK DETECTOR
OFF
MENU ENTER DOWN UP
Lock Detector OFF = Default Lock Detector ON: This function lets the user to activate the Lock detector on Pan and Tilt. When Lock detector is set to ON, the unit start the Pan&Tilt motors reset normally, but if for any reason there is something blocking the movement for Pan&Tilt motors during the initial reset (example unit into the fly case and power connected), it automatically will stop to reset Pan&Tilt motors after 5 seconds from the startup and a warning message (Pan locked-Tilt locked) will appear on unit display.
Reboot = Unit Reboot without needing of turning OFF the unit
Exit To Main = Exit from Reserved menu
RESERVED (Code = 100) Pan lock-Tilt lock Pan free-Tilt free Lock Detector Reboot Exit To Main
Up-Down
Menu
Up-DownENTER
ENTER
Center and sectors LEDs panels temperatures; CPU PCB temperature and LEDs max current value
Up-Down
Menu
Up-DownENTER
ENTER
LED LIFE HOURS: RGBW LEDs life time
Page 19
19
12- DISPLAY FUNCTIONS
Demo
Default
DEFAULT To restore main settings
13- PERIODIC CLEANING
13.1- Front lenses screen glass
The dust can reduce the luminous output substantially. Regularly clean the front lenses screen glass using a soft cotton cloth, dampened with a specialist lens cleaning solution.
13.2- Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. If necessary, clean the fans and air passages more frequently.
DEFAULT
SURE?
MENU ENTER DOWN UP
RESTORE MAIN SETTINGS
DEFAULT
RESTORE MAIN SETTINGS
MENU ENTER DOWN UP
PRESS ENTER TO CONFORM
PRESS MENU TO CANCEL
Up-Down
Menu
Up-DownENTER
ENTER
Default To restore main settings
Up-Down
Menu
Up-DownENTER
ENTER
DEMO Demo games without DMX
controller Pan, Tilt, Zoom effect, Zoom
speed, Dimmer, Shutter, LED effect and LED speed values selectable by user
DIMMER
DEMO
MENU ENTER DOWN UP
255
Page 20
20
14- PERIODIC CONTROLS
Mechanical parts
Periodically check all mechanical parts, replacing them if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors, refastening if necessary.
Fuse replacement
Locate the fuse, which protects the electronics, in the base of the WONDER. Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type (10AT) if necessary.
!
Page 21
21
15- DMX PROTOCOL
34 CHANNELS MODE (Default)
1 PAN msb 2 PAN lsb 3 TILT msb 4 TILT lsb 5 SPEED MOVEMENT 6 PAN FPR 7 SHUTTER 8 DIMMER 9 RED CENTER 10 GREEN CENTER 11 BLUE CENTER 12 WHITE CENTER 13 RED SECTOR 1 14 GREEN SECTOR 1 15 BLUE SECTOR 1 16 WHITE SECTOR 1 17 RED SECTOR 2 18 GREEN SECTOR 2 19 BLUE SECTOR 2 20 WHITE SECTOR 2 21 RED SECTOR 3 22 GREEN SECTOR 3 23 BLUE SECTOR 3 24 WHITE SECTOR 3 25 WHITE PRE-PROGRAMMED 26 CTC 27 MACROS 28 MACROS SPEED CONTROL 29 FUNCTIONS 30 ZOOM CENTRE / GLOBAL ZOOM 31 ZOOM SECTORS 32 ZOOM MODE 33 SERVICE
34 RESET
DMX CHANNEL
1
Parameter: PAN msb
DMX CHANNEL
2
Parameter: PAN lsb
DMX CHANNEL
3
Parameter: TILT msb
DMX CHANNEL
4
Parameter: TILT lsb
DMX CHANNEL
5
Parameter: SPEED MOVEMENT
DMX value
Function
000-010
Standard
011-025
Fast movement
026-127
Vector mode from fast to slow
128-247
Variable time reaction to dmx signal (fast to slow)
248-255
Silent movement
Page 22
22
DMX CHANNEL
6
Parameter: PAN FPR
DMX value
Function
000-010
Position mode 540° (standard path)
011-020
Position mode 360° ( 1 turn)
021-030
Position mode 720° ( 2 turns)
031-040
Position mode 1080° ( 3 turns)
041-050
Position mode 1440° ( 4 turns)
051-060
Position mode 1800° ( 5 turns)
061-070
Position mode 2160° ( 6 turns)
071-080
Position mode 2520° ( 7 turns)
081-090
Position mode 2880° ( 8 turns)
091-100
Position mode 3240° ( 9 turns)
101-110
Position mode 3600° (10 turns)
111-120
Position mode 360° smart path
121-182
Forward spin rotation speed from max to min
183-193
Stop
194-255
Reverse spin rotation speed from min to max
DMX CHANNEL
7
Parameter: SHUTTER
DMX value
Function
000-009
Black-out
010-019
Open
020-029
Black-out
030-034
Strobe speed 1 (1 flash/sec)
035-039
Strobe speed 2 (2 flash/sec)
040-044
Strobe speed 3 (3 flash/sec)
045-049
Strobe speed 4 (4 flash/sec)
050-054
Strobe speed 5 (5 flash/sec)
055-059
Strobe speed 6 (6 flash/sec)
060-064
Strobe speed 7 (7 flash/sec)
065-069
Strobe speed 8 (8 flash/sec)
070-074
Strobe speed 9 (10 flash/sec)
075-079
Strobe speed 10 (12 flash/sec)
080-084
Strobe speed 11 (14 flash/sec)
085-089
Strobe speed 12 (16 flash/sec)
090-094
Strobe speed 13 (18 flash/sec)
095-099
Strobe speed 14 (20 flash/sec)
100-104
Strobe speed 15 (22 flash/sec)
105-109
Strobe speed 16 (25 flash/sec)
110-114
Strobe speed 17 (30 flash/sec)
115-119
Strobe speed 18 (35 flash/sec)
120-149
Pulse UP (42.6 s – 120 ms)
150-179
Pulse DOWN (42.6 s – 120 ms)
180-191
Random strobe effect from slow to fast (all zones together) Dimmer, Red, Green, Blue, White channels active
192-203
Full independent random strobe effect from slow to fast (all zones together) Dimmer, Red, Green, Blue, White channels disabled
204-215
Random strobe effect from slow to fast (random zones)
216-229
Random strobe effect from slow to fast (random zone + random strobe)
230-255
Open
DMX CHANNEL
8
Parameter: DIMMER
DMX value
Function
000-007
Black-out
008-255
Proportional dimmer
Page 23
23
DMX CHANNEL
9
Parameter: RED CENTRE
DMX CHANNEL
10
Parameter: GREEN CENTRE
DMX CHANNEL
11
Parameter: BLUE CENTRE
DMX CHANNEL
12
Parameter: WHITE CENTRE
DMX CHANNEL
13
Parameter: RED SECTOR 1
DMX CHANNEL
14
Parameter: GREEN SECTOR 1
DMX CHANNEL
15
Parameter: BLUE SECTOR 1
DMX CHANNEL
16
Parameter: WHITE SECTOR 1
DMX CHANNEL
17
Parameter: RED SECTOR 2
DMX CHANNEL
18
Parameter: GREEN SECTOR 2
DMX CHANNEL
19
Parameter: BLUE SECTOR 2
DMX CHANNEL
20
Parameter: WHITE SECTOR 2
DMX CHANNEL
21
Parameter: RED SECTOR 3
DMX CHANNEL
22
Parameter: GREEN SECTOR 3
DMX CHANNEL
23
Parameter: BLUE SECTOR 3
DMX CHANNEL
24
Parameter: WHITE SECTOR 3
DMX value
Function
000-255
Proportional colour
DMX CHANNEL
25
Parameter: WHITE PRE-PROGRAMMED
DMX value
Function
000-055
No function
056-105
Full (red-green-blue at full)
106-155
White DTS
156-205
Custom white create (RGB levels selectable by DMX)
206-255
White CTC (channel 26 CTC enabled)
DMX CHANNEL
26
Parameter: CTC (Colour temperature correction)
IF CHANNEL 25 WHITE PRE-PROGRAMMED = WHITE CTC (DMX range value 206-255)
DMX value
Function
000-255
Linear control temperature correction (from 2700°K to 8000°K)
Page 24
24
DMX CHANNEL
27
Parameter: MACROS
DMX value
Function
000-014
No function
015-024
Macro 1 (static)
025-034
Macro 2 (static)
035-044
Macro 3 (static)
045-054
Macro 4 (static)
055-064
Macro 5 (static)
065-074
Macro 6 (static)
075-084
Macro 7 (static)
085-094
Macro 8 (static)
095-104
Macro 9 (static)
105-114
Macro 10 (static)
115-124
Macro 11 (static)
125-134
Macro 12 (static)
135-144
Macro 13 (static)
145-154
Macro 14 (static)
155-164
Macro 15 (static)
165-174
Macro 16 (static)
175-184
Rainbow effect (speed by channel 28)
185-189
All sectors dynamic effect 1 (speed by channel 28)
190-194
All sectors dynamic effect 2 (speed by channel 28)
195-199
All sectors dynamic effect 3 (speed by channel 28)
200-204
All sectors dynamic effect 4 (speed by channel 28)
205-209
All sectors dynamic effect 5 (speed by channel 28)
210-214
All sectors dynamic effect 6 (speed by channel 28)
215-219
All sectors dynamic effect 7 (speed by channel 28)
220-224
All sectors dynamic effect 8 (speed by channel 28)
225-229
All sectors dynamic effect 9 (speed by channel 28)
230-234
All sectors dynamic effect 10 (speed by channel 28)
235-239
All sectors dynamic effect 11 EMPTY (speed by channel 28)
240-244
All sectors dynamic effect 12 EMPTY (speed by channel 28)
245-249
All sectors dynamic effect 13 (speed by channel 28)
250-255
All sectors dynamic effect 14 (speed by channel 28)
DMX CHANNEL
28
Parameter: MACROS SPEED CONTROL
Active only if MACROS channel 27 between DMX values 175-255
DMX value
Function
Rainbow effect CH27 from 175 to 184
Dynamic Effect CH27 from 185 to 255
000-014
Rainbow effect Speed 1 ( 4 sec)
Dynamic Effect Speed 1 ( 0,1 sec)
015-029
Rainbow effect Speed 2 ( 6 sec)
Dynamic Effect Speed 2 ( 0,2 sec)
030-044
Rainbow effect Speed 3 ( 8 sec)
Dynamic Effect Speed 3 ( 0,3 sec)
045-059
Rainbow effect Speed 4 ( 10 sec)
Dynamic Effect Speed 4 ( 0,4 sec)
060-074
Rainbow effect Speed 5 ( 15 sec)
Dynamic Effect Speed 5 ( 0,5 sec)
075-089
Rainbow effect Speed 6 ( 20 sec)
Dynamic Effect Speed 6 ( 0,6 sec)
090-104
Rainbow effect Speed 7 ( 30 sec)
Dynamic Effect Speed 7 ( 0,8 sec)
105-119
Rainbow effect Speed 8 ( 45 sec)
Dynamic Effect Speed 8 ( 1 sec)
120-134
Rainbow effect Speed 9 ( 60 sec)
Dynamic Effect Speed 9 ( 1,5 sec)
135-149
Rainbow effect Speed 10 ( 90 sec)
Dynamic Effect Speed 10 ( 2 sec)
150-164
Rainbow effect Speed 11 (120 sec)
Dynamic Effect Speed 11 ( 3 sec)
165-179
Rainbow effect Speed 12 (150 sec)
Dynamic Effect Speed 12 ( 5 sec)
180-194
Rainbow effect Speed 13 (180 sec)
Dynamic Effect Speed 13 ( 7 sec)
195-209
Rainbow effect Speed 14 (210 sec)
Dynamic Effect Speed 14 ( 10 sec)
210-224
Rainbow effect Speed 15 (240 sec)
Dynamic Effect Speed 15 ( 15 sec)
225-239
Rainbow effect Speed 16 (270 sec)
Dynamic Effect Speed 16 ( 25 sec)
240-255
Rainbow effect Speed 17 (300 sec)
Dynamic Effect Speed 17 ( 30 sec)
DMX CHANNEL
29
Parameter: FUNCTIONS (Recall, Create, Store custom white)
IF CHANNEL 25 WHITE PRE-PROGRAMMED = CUSTOM WHITE (DMX range value 156-205)
DMX value
Function
000-079
Custom White Recall
080-160
Custom White Create (Enable custom white creation)
161-255
Custom White Store (Store the custom white created)
Page 25
25
DMX CHANNEL
30
Parameter: ZOOM CENTRE
IF CHANNEL 32 ZOOM MODE = INDEPENDENT ZOOM CONTROL (DMX range value 000-127)
DMX value
Function
000-255
ZOOM CENTRE Linear control from narrow to wide (3,5° - 52°)
IF CHANNEL 32 ZOOM MODE = GLOBAL ZOOM CONTROL (DMX range value 128-255)
DMX value
Function
000-255
GLOBAL ZOOM (Zoom centre + Zoom sectors) Linear control from narrow to wide (8° - 52°)
DMX CHANNEL
31
Parameter: ZOOM SECTORS
IF CHANNEL 32 ZOOM MODE = INDEPENDENT ZOOM CONTROL (DMX range value 000-127)
DMX value
Function
000-255
ZOOM SECTORS Linear control from narrow to wide (8° - 52°)
IF CHANNEL 32 ZOOM MODE = GLOBAL ZOOM CONTROL (DMX range value 128-255)
DMX value
Function
000-255
No function
DMX CHANNEL
32
Parameter: ZOOM MODE
DMX value
Function
000-127
Independent Zoom control: Zoom centre ch30 and Zoom sectors ch31 enabled
128-255
Global Zoom control on ch30 enabled; Zoom sectors ch31 disabled
DMX CHANNEL
33
Parameter: SERVICE
To activate following functions, stop in DMX value for at least 5 seconds. FUNCTION channel ch29 must be at range 161-255. WHITE PRE-PROGRAMMED channel ch25 must be at range 000-055. Corresponding DISPLAY MENU settings, will be overwritten.
DMX value
Function
000-014
No Function
015-024
SMOOTH OFF
025-034
SMOOTH 4
035-044
SMOOTH 8
045-054
SMOOTH 15
055-064
SMOOTH 20
065-074
GAMMA CORRECTION QUADRATIC
075-084
GAMMA CORRECTION LINEAR
085-094
OUTPUT FREQUENCY 610 Hz
095-104
OUTPUT FREQUENCY 1500 Hz
105-114
OUTPUT FREQUENCY 3000 Hz
115-124
OUTPUT FREQUENCY 6000 Hz
125-134
OUTPUT FREQUENCY 9000 Hz
135-144
BOOST ON
145-154
BOOST OFF
155-164
WIRELESS ON
165-174
WIRELESS UNLINK
175-184
WIRELESS OFF
185-194
PAN NORMAL
195-204
PAN REVERSE
205-214
TILT NORMAL
215-224
TILT REVERSE
225-234
RESERVED
235-244
Fans Speed Studio Mode (not yet implemented)
245-255
Fans Speed Live Mode (not yet implemented)
DMX CHANNEL
34
Parameter: RESET
DMX value
Function
000-015
No Function
016-075
PAN-TILT reset
076-135
ZOOM CENTRE reset
136-200
ZOOM SECTORS reset
201-239
ZOOM CENTRE + ZOOM SECTORS reset
240-255
TOTAL reset
Page 26
26
15- DMX PROTOCOL
38 CHANNELS MODE
1 PAN msb 2 PAN lsb 3 TILT msb 4 TILT lsb 5 SPEED MOVEMENT 6 PAN FPR 7 SHUTTER 8 DIMMER 9 RED CENTER 10 GREEN CENTER 11 BLUE CENTER 12 WHITE CENTER 13 RED SECTOR 1 14 GREEN SECTOR 1 15 BLUE SECTOR 1 16 WHITE SECTOR 1 17 RED SECTOR 2 18 GREEN SECTOR 2 19 BLUE SECTOR 2 20 WHITE SECTOR 2 21 RED SECTOR 3 22 GREEN SECTOR 3 23 BLUE SECTOR 3 24 WHITE SECTOR 3 25 WHITE PRE-PROGRAMMED 26 CTC 27 MACROS 28 MACROS SPEED CONTROL 29 FUNCTIONS 30 ZOOM CENTRE / GLOBAL ZOOM 31 ZOOM SECTORS 32 ZOOM MODE 33 SERVICE
34 RESET 35 SHUTTER CENTRE 36 SHUTTER SECTOR 1 37 SHUTTER SECTOR 2 38 SHUTTER SECTOR 3
DMX CHANNEL
1
Parameter: PAN msb
DMX CHANNEL
2
Parameter: PAN lsb
DMX CHANNEL
3
Parameter: TILT msb
DMX CHANNEL
4
Parameter: TILT lsb
Page 27
27
DMX CHANNEL
5
Parameter: SPEED MOVEMENT
DMX value
Function
000-010
Standard
011-025
Fast movement
026-127
Vector mode from fast to slow
128-247
Variable time reaction to dmx signal (fast to slow)
248-255
Silent movement
DMX CHANNEL
6
Parameter: PAN FPR
DMX value
Function
000-010
Position mode 540° (standard path)
011-020
Position mode 360° ( 1 turn)
021-030
Position mode 720° ( 2 turns)
031-040
Position mode 1080° ( 3 turns)
041-050
Position mode 1440° ( 4 turns)
051-060
Position mode 1800° ( 5 turns)
061-070
Position mode 2160° ( 6 turns)
071-080
Position mode 2520° ( 7 turns)
081-090
Position mode 2880° ( 8 turns)
091-100
Position mode 3240° ( 9 turns)
101-110
Position mode 3600° (10 turns)
111-120
Position mode 360° smart path
121-182
Forward spin rotation speed from max to min
183-193
Stop
194-255
Reverse spin rotation speed from min to max
DMX CHANNEL
7
Parameter: SHUTTER
DMX value
Function
000-009
Black-out
010-019
Open
020-029
Black-out
030-034
Strobe speed 1 (1 flash/sec)
035-039
Strobe speed 2 (2 flash/sec)
040-044
Strobe speed 3 (3 flash/sec)
045-049
Strobe speed 4 (4 flash/sec)
050-054
Strobe speed 5 (5 flash/sec)
055-059
Strobe speed 6 (6 flash/sec)
060-064
Strobe speed 7 (7 flash/sec)
065-069
Strobe speed 8 (8 flash/sec)
070-074
Strobe speed 9 (10 flash/sec)
075-079
Strobe speed 10 (12 flash/sec)
080-084
Strobe speed 11 (14 flash/sec)
085-089
Strobe speed 12 (16 flash/sec)
090-094
Strobe speed 13 (18 flash/sec)
095-099
Strobe speed 14 (20 flash/sec)
100-104
Strobe speed 15 (22 flash/sec)
105-109
Strobe speed 16 (25 flash/sec)
110-114
Strobe speed 17 (30 flash/sec)
115-119
Strobe speed 18 (35 flash/sec)
120-149
Pulse UP (42.6 s – 120 ms)
150-179
Pulse DOWN (42.6 s – 120 ms)
180-191
Random strobe effect from slow to fast (all zones together) Dimmer, Red, Green, Blue, White channels active
192-203
Full independent random strobe effect from slow to fast (all zones together) Dimmer, Red, Green, Blue, White channels disabled
204-215
Random strobe effect from slow to fast (random zones)
216-229
Random strobe effect from slow to fast (random zones + random strobe)
230-255
Open
Page 28
28
DMX CHANNEL
8
Parameter: DIMMER
DMX value
Function
000-007
Black-out
008-255
Proportional dimmer
DMX CHANNEL
9
Parameter: RED CENTRE
DMX CHANNEL
10
Parameter: GREEN CENTRE
DMX CHANNEL
11
Parameter: BLUE CENTRE
DMX CHANNEL
12
Parameter: WHITE CENTRE
DMX CHANNEL
13
Parameter: RED SECTOR 1
DMX CHANNEL
14
Parameter: GREEN SECTOR 1
DMX CHANNEL
15
Parameter: BLUE SECTOR 1
DMX CHANNEL
16
Parameter: WHITE SECTOR 1
DMX CHANNEL
17
Parameter: RED SECTOR 2
DMX CHANNEL
18
Parameter: GREEN SECTOR 2
DMX CHANNEL
19
Parameter: BLUE SECTOR 2
DMX CHANNEL
20
Parameter: WHITE SECTOR 2
DMX CHANNEL
21
Parameter: RED SECTOR 3
DMX CHANNEL
22
Parameter: GREEN SECTOR 3
DMX CHANNEL
23
Parameter: BLUE SECTOR 3
DMX CHANNEL
24
Parameter: WHITE SECTOR 3
DMX value
Function
000-255
Proportional colour
DMX CHANNEL
25
Parameter: WHITE PRE-PROGRAMMED
DMX value
Function
000-055
No function
056-105
Full (red-green-blue at full)
106-155
White DTS
156-205
Custom white create (RGB levels selectable by DMX)
206-255
White CTC (channel 26 CTC enabled)
DMX CHANNEL
26
Parameter: CTC (Colour temperature correction)
IF CHANNEL 25 WHITE PRE-PROGRAMMED = WHITE CTC (DMX range value 206-255)
DMX value
Function
000-255
Linear control temperature correction (from 2700°K to 8000°K)
Page 29
29
DMX CHANNEL
27
Parameter: MACROS
DMX value
Function
000-014
No function
015-024
Macro 1 (static)
025-034
Macro 2 (static)
035-044
Macro 3 (static)
045-054
Macro 4 (static)
055-064
Macro 5 (static)
065-074
Macro 6 (static)
075-084
Macro 7 (static)
085-094
Macro 8 (static)
095-104
Macro 9 (static)
105-114
Macro 10 (static)
115-124
Macro 11 (static)
125-134
Macro 12 (static)
135-144
Macro 13 (static)
145-154
Macro 14 (static)
155-164
Macro 15 (static)
165-174
Macro 16 (static)
175-184
Rainbow effect (speed by channel 28)
185-189
All sectors dynamic effect 1 (speed by channel 28)
190-194
All sectors dynamic effect 2 (speed by channel 28)
195-199
All sectors dynamic effect 3 (speed by channel 28)
200-204
All sectors dynamic effect 4 (speed by channel 28)
205-209
All sectors dynamic effect 5 (speed by channel 28)
210-214
All sectors dynamic effect 6 (speed by channel 28)
215-219
All sectors dynamic effect 7 (speed by channel 28)
220-224
All sectors dynamic effect 8 (speed by channel 28)
225-229
All sectors dynamic effect 9 (speed by channel 28)
230-234
All sectors dynamic effect 10 (speed by channel 28)
235-239
All sectors dynamic effect 11 EMPTY (speed by channel 28)
240-244
All sectors dynamic effect 12 EMPTY (speed by channel 28)
245-249
All sectors dynamic effect 13 (speed by channel 28)
250-255
All sectors dynamic effect 14 (speed by channel 28)
DMX CHANNEL
28
Parameter: MACROS SPEED CONTROL
Active only if MACROS channel 27 between DMX values 175-255
DMX value
Function
Rainbow effect CH27 from 175 to 184
Dynamic Effect CH27 from 185 to 255
000-014
Rainbow effect Speed 1 ( 4 sec)
Dynamic Effect Speed 1 ( 0,1 sec)
015-029
Rainbow effect Speed 2 ( 6 sec)
Dynamic Effect Speed 2 ( 0,2 sec)
030-044
Rainbow effect Speed 3 ( 8 sec)
Dynamic Effect Speed 3 ( 0,3 sec)
045-059
Rainbow effect Speed 4 ( 10 sec)
Dynamic Effect Speed 4 ( 0,4 sec)
060-074
Rainbow effect Speed 5 ( 15 sec)
Dynamic Effect Speed 5 ( 0,5 sec)
075-089
Rainbow effect Speed 6 ( 20 sec)
Dynamic Effect Speed 6 ( 0,6 sec)
090-104
Rainbow effect Speed 7 ( 30 sec)
Dynamic Effect Speed 7 ( 0,8 sec)
105-119
Rainbow effect Speed 8 ( 45 sec)
Dynamic Effect Speed 8 ( 1 sec)
120-134
Rainbow effect Speed 9 ( 60 sec)
Dynamic Effect Speed 9 ( 1,5 sec)
135-149
Rainbow effect Speed 10 ( 90 sec)
Dynamic Effect Speed 10 ( 2 sec)
150-164
Rainbow effect Speed 11 (120 sec)
Dynamic Effect Speed 11 ( 3 sec)
165-179
Rainbow effect Speed 12 (150 sec)
Dynamic Effect Speed 12 ( 5 sec)
180-194
Rainbow effect Speed 13 (180 sec)
Dynamic Effect Speed 13 ( 7 sec)
195-209
Rainbow effect Speed 14 (210 sec)
Dynamic Effect Speed 14 ( 10 sec)
210-224
Rainbow effect Speed 15 (240 sec)
Dynamic Effect Speed 15 ( 15 sec)
225-239
Rainbow effect Speed 16 (270 sec)
Dynamic Effect Speed 16 ( 25 sec)
240-255
Rainbow effect Speed 17 (300 sec)
Dynamic Effect Speed 17 ( 30 sec)
DMX CHANNEL
29
Parameter: FUNCTIONS (Recall, Create, Store custom white)
IF CHANNEL 25 WHITE PRE-PROGRAMMED = CUSTOM WHITE (DMX range value 156-205)
DMX value
Function
000-079
Custom White Recall
080-160
Custom White Create (Enable custom white creation)
161-255
Custom White Store (Store the custom white created)
Page 30
30
DMX CHANNEL
30
Parameter: ZOOM CENTRE
IF CHANNEL 32 ZOOM MODE = INDEPENDENT ZOOM CONTROL (DMX range value 000-127)
DMX value
Function
000-255
ZOOM CENTRE Linear control from narrow to wide (3,5° - 52°)
IF CHANNEL 32 ZOOM MODE = GLOBAL ZOOM CONTROL (DMX range value 128-255)
DMX value
Function
000-255
GLOBAL ZOOM (Zoom centre + Zoom sectors) Linear control from narrow to wide (8° - 52°)
DMX CHANNEL
31
Parameter: ZOOM SECTORS
IF CHANNEL 32 ZOOM MODE = INDEPENDENT ZOOM CONTROL (DMX range value 000-127)
DMX value
Function
000-255
ZOOM SECTORS Linear control from narrow to wide (8° - 52°)
IF CHANNEL 32 ZOOM MODE = GLOBAL ZOOM CONTROL (DMX range value 128-255)
DMX value
Function
000-255
No function
DMX CHANNEL
32
Parameter: ZOOM MODE
DMX value
Function
000-127
Independent Zoom control: Zoom centre ch30 and Zoom sectors ch31 enabled
128-255
Global Zoom control on ch30 enabled; Zoom sectors ch31 disabled
DMX CHANNEL
33
Parameter: SERVICE
To activate following functions, stop in DMX value for at least 5 seconds. FUNCTION channel ch29 must be at range 161-255. WHITE PRE-PROGRAMMED channel ch25 must be at range 000-055. Corresponding DISPLAY MENU settings, will be overwritten.
DMX value
Function
000-014
No Function
015-024
SMOOTH OFF
025-034
SMOOTH 4
035-044
SMOOTH 8
045-054
SMOOTH 15
055-064
SMOOTH 20
065-074
GAMMA CORRECTION QUADRATIC
075-084
GAMMA CORRECTION LINEAR
085-094
OUTPUT FREQUENCY 610 Hz
095-104
OUTPUT FREQUENCY 1500 Hz
105-114
OUTPUT FREQUENCY 3000 Hz
115-124
OUTPUT FREQUENCY 6000 Hz
125-134
OUTPUT FREQUENCY 9000 Hz
135-144
BOOST ON
145-154
BOOST OFF
155-164
WIRELESS ON
165-174
WIRELESS UNLINK
175-184
WIRELESS OFF
185-194
PAN NORMAL
195-204
PAN REVERSE
205-214
TILT NORMAL
215-224
TILT REVERSE
225-234
RESERVED
235-244
Fans Speed Studio Mode(not yet implemented)
245-255
Fans Speed Live Mode (not yet implemented)
Page 31
31
DMX CHANNEL
34
Parameter: RESET
DMX value
Function
000-015
No Function
016-075
PAN-TILT reset
076-135
ZOOM CENTRE reset
136-200
ZOOM SECTORS reset
201-239
ZOOM CENTRE + ZOOM SECTORS reset
240-255
TOTAL reset
DMX CHANNEL
35 36 37 38
Parameter: SHUTTER CENTRE Parameter: SHUTTER SECTOR 1 Parameter: SHUTTER SECTOR 2 Parameter: SHUTTER SECTOR 3
DMX value
Function
000-009
Black-out
010-019
Open
020-029
Black-out
030-034
Strobe speed 1 (1 flash/sec)
035-039
Strobe speed 2 (2 flash/sec)
040-044
Strobe speed 3 (3 flash/sec)
045-049
Strobe speed 4 (4 flash/sec)
050-054
Strobe speed 5 (5 flash/sec)
055-059
Strobe speed 6 (6 flash/sec)
060-064
Strobe speed 7 (7 flash/sec)
065-069
Strobe speed 8 (8 flash/sec)
070-074
Strobe speed 9 (10 flash/sec)
075-079
Strobe speed 10 (12 flash/sec)
080-084
Strobe speed 11 (14 flash/sec)
085-089
Strobe speed 12 (16 flash/sec)
090-094
Strobe speed 13 (18 flash/sec)
095-099
Strobe speed 14 (20 flash/sec)
100-104
Strobe speed 15 (22 flash/sec)
105-109
Strobe speed 16 (25 flash/sec)
110-114
Strobe speed 17 (30 flash/sec)
115-119
Strobe speed 18 (35 flash/sec)
120-179
Black-out
180-191
Random strobe
192-229
Black-out
230-255
Open
Page 32
32
MADE IN ITALY
ISO 9001:2008
D.T.S. quality system
is certified to the
ISO 9001:2008 standard
D.T.S. products are designed and manufactured at the D.T.S. plants in italy
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.
D.T.S. Illuminazione s.r.l. – Via Fagnano Selve 10-12-14 47843
Misano Adriatico (RN) Italia
Tel.: +39 0541 611131. Fax + 39 0541 611111
info@dts-lighting.it www.dts-lighting.it
0517I262
*0517I262*
Loading...