DTS Wonder D, Wonder S User Manual

D.T.S. Illuminazione s.r.l.

Via Fagnano Selve 10/12/14
47843 Misano Adriatico (RN) ITALIA Tel [phone] Fax [phone] [e-mail] http://www.dts-lighting.it

Made in Italy

User’s Manual rel 1.0 GB

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and
checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

d'éventuelles inexactitudes. Tous droits réservés. Ce document ne peut être copié,

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1 - SYMBOLS........................................................................................................................... 4

2 - GENERAL WARNING......................................................................................................... 5

3 - GENERAL WARRANTY CONDITIONS .............................................................................. 5

4 - TECHNICAL FEATURES .................................................................................................... 5

5 - ACCESSORIES .................................................................................................................. 7

6 - IMPORTANT SAFETY INFORMATION .............................................................................. 8

6.1 Fire prevention ............................................................................................................... 8

6.2 Prevention of electric shock ........................................................................................... 8

6.3 Safety ............................................................................................................................ 8

6.4 Level of protection against the penetration of solid and liquid objects ............................ 8

6.5 Long-life auto-charging buffer battery ............................................................................ 8

7 - VOLTAGE AND FREQUENCY ........................................................................................... 9

8 - INSTALLATION .................................................................................................................. 9

8.1 Safety cable ................................................................................................................. 10

8.2 Protection against liquids ............................................................................................. 10

8.3 Movement .................................................................................................................... 11

8.4 Risk of fire .................................................................................................................... 11

8.5 Forced ventilation ........................................................................................................ 11

8.6 Ambient temperature ................................................................................................... 11

9 - MAINS CONNECTION ...................................................................................................... 12

9.1 Protection .................................................................................................................... 12

10 - DMX SIGNAL CONNECTION ......................................................................................... 13

10.1 DMX addresses ....................................................................................................... 13

10.2 Selecting the DMX address ...................................................................................... 13

11 - FIRMWARE UPDATING ................................................................................................ 14

12 - DISPLAY FUNCTIONS .................................................................................................. 15

13 - PERIODIC CLEANING .................................................................................................... 19

13.1 Front lenses screen glass ........................................................................................ 19

13.2 Fans and air passages ............................................................................................. 19

14 - PERIODIC CONTROLS ................................................................................................. 19

15 - DMX PROTOCOL ........................................................................................................... 21

4

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

Never handle the unit until at least 10 minutes have

elapsed since the projector was turned off.

THIS SYMBOL INDICATES TEMPERATURE
OF THE EXTERNAL SURFACE

The maximum temperature that can be reached
on the external surface of the fitting, in a
thermally steady state, is 80°C (176°F).

THIS SYMBOL INDICATES THE
ELECTRIC SHOCK RISK

High voltage is present inside the unit. Unplug the
unit prior to performing any function which
involves touching the inside of the moving head.

THIS SYMBOL INDICATES PROTECTION
AGAINST ELECTRICAL SHOCK
Connection must be made to a power supply system
fitted with efficient earthing (Class I appliance).

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS YOU CAN PLACE THE

UNIT ON NORMALLY FLAMMABLE SURFACES

Suitable for mounting on normally flammable

materials surfaces greater than 200°C with

some combustion time lag.

THIS SYMBOL MEANS
PHOTOBIOLOGICAL SAFETY

Caution: Possibly hazardous optical radiation emitted
from this product. Do not stare at operating light

source. May be harmful to the eyes.

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE FROM ILLUMINATED OBJECTS

LONG-LIFE AUTO-CHARGING BUFFER BATTERY
The projector contains a rechargeable lead-acid or

lithium iron tetraphosphate battery. To preserve the
environment, please dispose the battery at the end
of its life according to the regulation in force.

!

5

2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation, use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or
experienced person.
Always disconnect the device from the mains before maintenance.
The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing
material defects.

4- TECHNICAL FEATURES

Overview
WONDER S introduces a revolutionary fixture architecture: an exclusive optical

system consisting of two concentric zones, each featuring a different type of lenses.
This new technology achieves an unprecendeted result: the brightest most uniform
wall wash ever seen.
In traditional wash lights, in fact, when the beam is widened to illuminate a larger area,
a darker spot is visible in the center. The exclusive optics of the WONDER S, however
lets you balance the brightness of the entire beam with that of its center, resulting in
unparalleled evenly diffused luminosity.
You can also obtain stunning multicolor projections: WONDER S LED board consists
of four independent zones: a central one, and a ring divided into three distinct
sections. Each of these four areas has individual control of luminosity, colors and
effects: it’s like having four LED fixtures in one.

The unit is also available as WONDER D, offering an exclusive double concentric
optical system featuring different lenses and linear zoom ranges (central: 3.5° - 52°
zoom; ring: 8° - 52° zoom).
This revolutionary configuration results in an unprecendented evenly diffused
luminosity, size and color.
WONDER D can create amazing concentric multi-color beams and effects in the air,
guaranteed to astonish any audience. Also, WONDER D comes equipped with the

‘FPR’ system (D.T.S. patent), which allows limitless pan rotation, in either direction,

never having to reverse motion.

WONDER S FC

(D.T.S. Product Code: 03.LDR014.F)

• Electronic ballast 90-260Vac 50-60 Hz • Black finish
WONDER D FPR FC

(D.T.S. Product Code: 03.LDR013.FFP)

• Electronic ballast 90-260Vac 50-60 Hz • FPR (Free Pan Rotation) • Black finish

6

4- TECHNICAL FEATURES

LED Technology
49 FULL COLOUR LEDs (RGBW)

Optical group

WONDER S:
7 x 3.5° lenses; 42 x 8° lenses

3.5° - 52° long excursion high-efficiency linear motorized zoom

22.000 Lux / 5 m
WONDER D:
2 concentric independent high efficiency optical groups
Optical group 1 (7 lenses): 3.5° - 52° long excursion linear motorized zoom
Optical group 2 (42 lenses): 8°- 52° long excursion linear motorized zoom

22.000 Lux / 5 m
Color generation

4 discrete LED areas; each area is independently controllable (luminosity, colors,
effects) 16 million colors each
Wide palette of pure uniform whites with variable linear color temperature (2700K –
8000K)

Interface / Control / Programming
LCD graphic display + 4 soft-keys (control / management of the main parameters)
Long-life auto-charging buffer battery
RDM
ARTNET ready
Wireless ready
Updatable internal operating system
Li-Fe display backup battery (WONDER D)

DMX channels
34 ch (Default) or 38 ch

Pan & Tilt

WONDER S:
Pan 540°: 2.5 sec.; Tilt 270°: 1.5 sec
WONDER D:
‘FPR’ system (D.T.S. patent)
Pan: limitless rotation, in both directions; 360° rotation in 1.56 sec.; Tilt 270°: 1.5 sec.
Tri-phase stepper motor technology for ultra-fast silent movements
16-bit resolution
Selectable speed ranges
Pan / Tilt lock

Power supply
Electronic full-range 90-260Vac 50-60 Hz
Power consumption: 850W

Connection
DMX: 4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik
Power supply: POWERCON IN and OUT (re-launch) connectors by Neutrik

7

Operating ambient temperature

-10° / 40°
Weight

22 Kg
International certifications

Certification CE; LED Class: Class 2 LED product

DIMENSIONS

Packaging Dimensions (LxWxH)
610 x 410 x 695 mm
Weight: 27 Kg

5- ACCESSORIES

As standard

* 1 x POWERCON male cable connector (Code 0520P014)
* 1 x XLR 5 Pins male cable connector (Code 0508B066)
* 1 x XLR 5 Pins female cable connector (Code 0508B065)
* 2 x Omega clamp with “Fast Lock” connection 1/4 turn (Code 02K00549)
* User’s manual

Optional (on request)

• “C” Clamp G100 black / professional (max. load 200Kg) (Code 0521A015)

• Aliscaf Clamp (max. capacity load 100Kg) (Code 0521A008)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (Code

0521A010)

8

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

-It is permissible to place the unit on normally flammable surfaces.
Suitable for mounting on normally flammable materials surfaces greater than 200°C
with some combustion time lag.

-Minimum distance from the closest illuminable surface: 0,5 m.

-Replace any blown or damaged fuses only with those of identical value (10AT).
Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.
It is, moreover, recommended to protect the supply lines of the projectors from
indirect contact and/or shorting to earth by using appropriately sized residual current
devices.

6.2 Prevention of electric shock:

-High voltage is present inside the unit.
Unplug the unit prior to performing any function which involves touching the inside of
the moving head.

-The level of technology inherent in the WONDER requires the assistance of
specialised personnel for all servicing.
Please refer to an authorised D.T.S. service centre.

-Connection must be made to a power supply system fitted with efficient earthing
(Class I appliance).

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Safety:

-The projector should always be installed with bolts, clamps and other tools that are
capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the
failure of the main fixing point.

-The maximum temperature that can be reached on the external surface of the fitting,
in a thermally steady state, is 80°C (176°F).
Never handle the unit until at least 10 minutes have elapsed since the projector
was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow.
The ambient temperature should not exceed 40°C.

-Caution: Possibly hazardous optical radiation emitted from this product.
Do not stare at operating light source. May be harmful to the eyes.

6.4 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level
against the penetration of solid and liquid objects is IP20.

6.5 Long-life auto-charging buffer battery:

-The projector contains a rechargeable lead-acid or lithium iron tetraphosphate
battery. To preserve the environment, please dispose the battery at the end
of its life according to the regulation in force.

!!!

9

7- VOLTAGE AND FREQUENCY
The WONDER with electronic ballast can operate at 90-260Vac 50-60 Hz.

8- INSTALLATION

WONDER may be either floor or ceiling mounted.
For floor mounting installations, the WONDER is
supplied with four rubber mounting feet on the
base. For ceiling mounted installations, we
reccomend the use of appropriate clamps to fix
the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the
weight of the unit, as should any clamps used to hang it.
The structure should also be sufficiently rigid so as not to move or shake whilst the
WONDER is moving.
Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the
WONDER by using the two omega clamps (provided in the box) in conjunction with
fixing clamps for truss (fixing clamps are not included into the unit box).

10

8.1- Safety cable

We recommend the use of a safety cable or chain connected to the WONDER and to
the suspension truss in order to avoid the fixture accidentally falling should the main
fixing point fail.
Make sure that the iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain/cord to the attachment point (A) located on the base
of the fixture, as shown in the picture below.

8.2 Protection against liquids

The projector contains electric and electronic components which should under no
circumstances come into contact with oil, water or any other liquid.
The proper unit functioning would be compromised should this occur.

!