DTS TITAN SOLO User Manual

TITAN SOLO

User’s Manual Rel 1.6

D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it

GB

Made in Italy

2

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

TITAN SOLO

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

D.T.S.

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

D.T.S.

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

D.T.S.

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

D.T.S.

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S

D.T.S.

3

DESCRIPTION

TITAN SOLO is a new range of compact self-contained LED projectors designed for fixed and
mobile installations either indoor or outdoor.
All models are made on aluminium offering high resistance to mechanical stress, and IP20 or
IP65 protection rating.
TITAN SOLO range features

up and use.
2 integrated power supply with different protection rating are available: IP20 (Powerconn + XLR

connectors), and IP65 (3 x 1.5 sq mm Main AC cable 1 meter lenght +

cable connectors
TITAN is also available without integrated power supply.
Three dedicated lenses sets (Spot, Medium flood, Wide flood) are available for each model,
offering different light beam projection angles with even coverage of lighted areas.
TITAN SOLO can be controlled via any DMX lighting console.
TITAN range comprises 3 models, which employ different sets of LEDs tailored for distinct
applications: TITAN SOLO FULL COLOUR, TITAN SOLO RGB and TITAN SOLO WHITE.
TITAN SOLO FULL COLOUR: 15 x 3W Full Colour LEDs; 16 million colours; 990 Lux at 2 m
(spot lenses); linear colour temperature 3200°K ÷ 5500°K; 16 selectable types of White.
The 15 Full Colour LEDs all generate the same colour at the same time, so that the illuminated
object is not only uniformly lit, but also projects no false shadows.
TITAN SOLO RGB: 54 x 1W P4 LEDs (12 x Red, 15 x Green, 15 x Blue, 12 x Amber); 16 million
colours; 4388 Lux at 2 m (spot lenses); linear colour temperature 3200°K ÷ 5500°K; 16
selectable types of White. The LEDs distribution pattern guarantees high mixing quality for RGB
colours and a uniform projection on surfaces, no matter what colour is used.
TITAN SOLO WHITE: 54 x 1W P4 LEDs (42 White, 12 x Amber); 9900 Lux at 2 m (spot lenses);
linear colour temperature 3200°K ÷ 5500°K; 16 selectable types of White.
TITAN SOLO WHITE is ideal in various applications where colour is not needed and white light
must have well defined features.

1 meter cable lenght ).

an integrated power supply and is therefore extremely easy to set

XLR Male / Female

TITAN SOLO

Full colour LEDs Power supply on board

03.LDB030S.F10 TITAN SOLO IP20 FULLCOLOUR SPOT LENSES

03.LDB030S.F25 TITAN SOLO IP20 FULLCOLOUR MEDIUM FLOOD LENSES

03.LDB030S.F40 TITAN SOLO IP20 FULLCOLOUR WIDE FLOOD LENSES

03.LDB036C.F10 TITAN SOLO C IP65 FULLCOLOUR SPOT LENSES

03.LDB036C.F25 TITAN SOLO C IP65 FULLCOLOUR MEDIUM FLOOD LENSES

03.LDB036C.F40 TITAN SOLO C IP65 FULLCOLOUR WIDE FLOOD LENSES

Red/Green/Blue/Amber LEDs Power supply on board

03.LDB030S.T10 TITAN SOLO IP20 RGBA SPOT LENSES

03.LDB030S.T25 TITAN SOLO IP20 RGBA MEDIUM FLOOD LENSES

03.LDB030S.T40 TITAN SOLO IP20 RGBA WIDE FLOOD LENSES

03.LDB036C.T10 TITAN SOLO C IP65 RGBA SPOT LENSES

03.LDB036C.T25 TITAN SOLO C IP65 RGBA MEDIUM FLOOD LENSES

03.LDB036C.T40 TITAN SOLO C IP65RGBA WIDE FLOOD LENSES

3 X White /Amber LEDs Power supply on board

03.LDB030S.W10 TITAN SOLO IP20 WHITE SPOT LENSES

03.LDB030S.W25 TITAN SOLO IP20WHITE MEDIUM FLOOD LENSES

03.LDB030S.W40 TITAN SOLO IP20WHITE WIDE FLOOD LENSES

03.LDB036C.W10 TITAN SOLO C IP65 WHITE SPOT LENSES

03.LDB036C.W25 TITAN SOLO C IP65 WHITE MEDIUM FLOOD LENSES

03.LDB036C.W40 TITAN SOLO C IP65 WHITE WIDE FLOOD LENSES

4

LED technology

TITAN SOLO FULL COLOUR: 15 x Full Colour LEDs; 990 Lux / 2 m (spot lenses)
TITAN SOLO RGB: 54 x 1W P4 LEDs (12 x Red, 15 x Green, 15 x Blue, 12 x Amber; 4388 Lux /
2 m (spot lenses)
TITAN SOLO WHITE: 54 x 1W P4 LEDs (42 x White, 12 x Amber) 9900 Lux / 2 m (spot lenses)
Variable white colour temperature:

3.200°K÷5.500°K
No infrared emission; no ultraviolet emission
LEDs average lifespan: 100.000 hours

Optical units

3 lenses sets available (Spot, Medium flood, Wide flood)

Control

Via any DMX lighting console

Protection

IP20 or IP65 protection level against the penetration of solids and liquids

Construction

TITAN SOLO is made on aluminium

Power supply

Internal power supply

Connection

M12 connection system between head and power supply (

IP65

)

Powerconn + XLR connectors

3 x 1.5 sq mm Main AC cable 1 meter lenght + 1 meter
cable lenght (TITAN SOLO IP65)

panel (TITAN SOLO IP20)

XLR Male / Female cable connectors

TITAN SOLO IP20 / TITAN SOLO

TITAN SOLO

ACCESSORIES

Lenses set Spot (TITAN SOLO FULL COLOUR) (Cod. 03.LK.019)
Lenses set Medium flood (TITAN SOLO FULL COLOUR) (Cod. 03.LK.020)
Lenses set Wide flood (TITAN SOLO FULL COLOUR) (Cod. 03.LK.021)
Lenses set Spot (TITAN SOLO RGB / WHITE) (Cod. 03.LK.022)
Lenses set Medium flood (TITAN SOLO RGB / WHITE) (Cod. 03.LK.023)
Lenses set Wide flood (TITAN SOLO RGB / WHITE) (Cod. 03.LK.024)
10XAWG26 multipolar black outdoor cable (Cod. 0509C061)
M12 female (8 pole) cable connector (Cod. 0520P050)
M12 male (8 pole) cable connector (Cod 0520P051)

MAIN ELECTRICAL CHARACTERISTICS:

Input Voltage Range : Vin 90 - 260 Vac
Frequency : 50 - 60 HZ
Power Consumption Range : 6 - 100 W
Power Factor ( Pf) : 0.95 electronic PFC controller
Efficiency : 90% typical

Output:

Power Output Range : 4 channels output 1,5 - 25W per channel
Output Current : 350 mA @ 100% per channel (500mA @ 100% per channel in BOOST Mode)
Output Voltage : Vout 48V

Control Input:

Control Signal : DMX 512
Dimming System :Constant Current PWM
Address Range : DMX 512 channels addressable by display

5

IMPORTANT SAFETY INFORMATION

Fire prevention:

Never locate the fixture on any flammable surface.
Minimum distance from flammable materials: 10 cm
Replace any blown or damaged fuses only with those of identical value

Prevention from electric shock:

High voltage is present inside the unit.
Unplug the unit prior to performing any operation which involves touching the inside of the unit.
This equipment must be grounded, do not connect to non-grounded supplies.

The use of a thermal magnetic circuit breaker is recommended for each TITAN SOLO unit.

Use only AC supplies 90-260V, 50-60Hz
TITAN SOLO IP20 should never be located in position exposed to rain or in areas of extreme
humidity.
A good air ventilation is essential for proper equipment work.

Safety:

TITAN SOLO

The external surface of the unit may exeed 50°C; never handle the unit until at least 5 minutes
have elapsed since the unit was turned off.
Never install the unit in an enclosed area lacking sufficient air flow.
The ambient temperature should not exeed 40°C and should not be lower than -10°C

UNIT DIMENSIONS:

Unit Dimensions
(LxWxH)
250 x 256 x 206 mm

Weight
6,3 Kg

Packing Dimensions
(LxWxH)
300 x 320 x 220 mm

Weight
7,5 Kg

INPUT/OUTPUT CONNECTIONS

TITAN SOLO IP20

6

TITAN SOLO

Panel display

DMX IN/OUT
XLR 3 pins Male / Female
Panel Connectors

Mains 90-260 V AC
50-60 Hz input Powerconn
Female panel connector

Fuse 3,15 AT

DMX IN/OUT
XLR 5 pins Male / Female
Panel Connectors

M12 LED output
Female cable connector

3

2

4

CONNECTOR PINOUT

CONNECTOR

1-RED +

1-RED + (FC / RGB / WHITE)
2-RED -

2-RED - (FC / RGB / WHITE)
3-GREEN +

3-GREEN + (FC / RGB / WHITE)

4-GREEN -

4-GREEN - (FC / RGB / WHITE)
5-BLUE +

5-BLUE + (FC / RGB / WHITE)
6-BLUE -

6-BLUE - (FC / RGB / WHITE)

7-AMBER - (RGB / WHITE)

7-

8-AMBER + (RGB / WHITE)

M12 LED input
Male cable connector

3

4

2

LEDS

LEDS

Pin1

7

6

5

5

6

7

Pin1

INPUT/OUTPUT CONNECTIONS

TITAN SOLO IP65

Mains 90-260 V AC
50-60 Hz input
3 x 1.5mm Cable

2

7

TITAN SOLO

Fuse 3,15 AT

DMX IN/OUT
XRL 5 pin Male
Cable Connectors

Display panel

DMX IN/OUT
XRL 5 pin Female
Cable Connectors

CONTROLLER
S T A N D A R D
D M X 5 1 2

LEDS

LEDS

CONNECTOR PINOUT

CONNECTOR

1-RED +

1-RED + (FC / RGB / WHITE)

M12 LED output
Female cable connector

3

2

4

5

Pin1

Please note that the XLR connectors installed on the TITAN IP65 have an
IP20 protection rate.
Thus, for any application where an IP65 rate is needed, the XLR connectors
must be protected within an IP65-rated container.

6

7

M12 LED input
Male cable connector

3

4

2

5

6

Pin1

7

2-RED -

2-RED - (FC / RGB / WHITE)
3-GREEN +

3-GREEN + (FC / RGB / WHITE)

4-GREEN -

4-GREEN - (FC / RGB / WHITE)
5-BLUE +

5-BLUE + (FC / RGB / WHITE)
6-BLUE -

6-BLUE - (FC / RGB / WHITE)

7-AMBER - (RGB / WHITE)

7-

8-AMBER + (RGB / WHITE)

8

TITAN SOLO

DMX SIGNAL CONNECTION:

TITAN SOLO IP20

The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or
between units must be carried out using a two pair screened ø0.5 mm.

Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX
connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN
projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to
the DMX IN plug of the second one.
In this way, all the projectors are cascade connected.

CONTROLLER
S T A N DA R D
D M X 5 1 2

5

4 2

3

1

1=GND
2=DATA­3=DATA+

P.S:
If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

5

4

120 ohm

1

2

3

OUT

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

PIN 3

PIN 2

9

TITAN SOLO

DMX SIGNAL CONNECTION:

TITAN SOLO IP65

The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or
between units must be carried out using a two pair screened ø0.5 mm.

Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX
connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN
projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to
the DMX IN plug of the second one.
In this way, all the projectors are cascade connected.

CONTROLLER
S T A ND A RD
D M X 5 1 2

5

4 2

1

1=GND
2=DATA-

3

3=DATA+

P.S:
If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

5

4

120 ohm

1

2

3

OUT

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

PIN 3

PIN 2

Please note that the XLR connectors installed on the TITAN IP65 have an
IP20 protection rate.
Thus, for any application where an IP65 rate is needed, the XLR connectors
must be protected within an IP65-rated container.

10

TITAN SOLO

DMX ADDRESS

TITAN SOLO FULL COLOR can be used in three different modes: 6 DMX channels, 9 DMX
channels (default) or CUSTOM DMX channels.
TITAN SOLO RGB and TITAN SOLO WHITE can be used in two different modes: 10 DMX
channels (default) or CUSTOM DMX channels.

If you want to use the TITAN SOLO FULL COLOUR in 6 channels mode, select the 6 CH mode
from the MODE menu and set the following addresses on the mixer: (To be used only with

DTS Wall mounted DMX controller 0514L007)

Projector 1 A001
Projector 2 A009
Projector 3 A017
….. A….
projector 6 A041

If you want to use the TITAN SOLO FULL COLOUR in 9 channels mode, select the 9 CH mode
from the MODE menu and set the following addresses on the mixer:

Projector 1 A001
Projector 2 A010 If you want to select the next projector, just add “9”
Projector 3 A019
….. A….
projector 6 A046

If you want to use the TITAN SOLO FULL COLOUR in CUSTOM DMX channels mode, select the
CUSTOM mode from the MODE menu and set the parameters for Shutter, Dimmer, Red, Green,
Blue, Ctc, Macro and Function to the desired DMX channels and confirm the settings with DONE

If you want to use the TITAN SOLO RGB / WHITE in 10 channels mode, select the 10 CH mode
from the MODE menu and set the following addresses on the mixer:

Projector 1 A001
Projector 2 A011 If you want to select the next projector, just add “9”
Projector 3 A021
….. A….
projector 6 A051

If you want to use the TITAN SOLO RGB / WHITE in CUSTOM DMX channels mode, select the
CUSTOM mode from the MODE menu and set the parameters for Shutter, Dimmer, Red, Green,
Blue, (White 1,White 2, White 3), Amber, Ctc, Macro and Function to the desired DMX channels
and confirm the settings with DONE

Selelcting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the
display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and
you get a faster selection.

DISPLAY FUNCTIONS

TITAN SOLO FULL COLOUR

11

TITAN SOLO

MENU

ENTER

DOWN

UP

DISPLAY FUNCTIONS

The TITAN SOLO FULL COLOUR display panel shows all the available functions . Using these
functions, it is possible to change some of the parameters and add some functions. Changing the
D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 signal
used to control it. Carefully follow the instructions below before carrying out any variations or
selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Software version 2.10

MENU

REVERSE DISPLAY
Reverses display's reading depending on
the mounting position
(On the ground or suspended).

DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.

ENTERUp-Down

Up-Down

Up-Down

Up-DownENTER

position

Suspension

position

Floor

Up-DownENTER

Display OFF

Display

always ON

ENTER

ENTER

ENTER

ENTER

Up-Down

DMX MODE
To select DMX mode : 9 (default) - 6 ­AUX - CUSTOM

CUSTOM DMX mode let you set the
parameters for Shutter, Dimmer, Red,
Green, Blue, Ctc, Macro and Function to
the desired DMX channels.

AUX mode let you activate an external
ON -OFF control on IR connector.
(Not implemented on TITAN SOLO)

MACRO Function, enable channel
mapping macro rainbow effects
STD (default)

Up-DownMENU ENTER

Up-Down

Up-Down

Up-Down

Up-Down

9 CHANNELS

6 CHANNELS

Up-DownENTER

AUX MODE

Up-DownENTER

ENTER

ENTER

ENTER

Default DMX Mode = 9 CH

Custom mode enabled

ENTER

Show Custom settings

ENTER

Setting the parameters
on Custom Mode

ENTER

Not implemented on
TITAN SOLO

Standard mode enabled

ENTER

(Default)

Show Custom settings

ENTER

12

TITAN SOLO

Up-Down

BOOST DRIVING
This menu allow to increase the
LED’s current from 350mA to 500
mA

Up-Down

MENU

ENTERUp-Down

LED
RGB Min/Max, Smooth and Compression
level values settings

Up-Down

RGB MINIMUM VALUES
This menu allow to select the
minimum levels for Red,Green and
blue

RGB MAXIMUM VALUES
This menu allow to select the

Up-Down

maximum levels for Red,Green and
blue

These settings have priority on Master
Dimmer (DMX channel 2)

Up-DownMENU ENTER

Up-Down

Boost mode activated

Boost mode deactivated

Up-DownENTER

Up-DownENTER

Up-DownENTER

ENTER

ENTER

Whit BOOST active,the LED’s
current is setted to 500mA
(30%more gain).
Default = Disable

Default = 0

Default = 255

Default = 0

Default = 255

Default = 0

Default = 255

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

SMOOTH VALUE
This menu allow to select the value
of the delay ( in millisecons) for
RGB and Dimmer channels
reaction to DMX or Program
variation.
Off=25 ms delay (Fast response)
20=250 ms delay (Slow response)

COMPRESSION
This menu allow to select between
Linear current output or Quadratic
current output for LEDs
Default = Linear

SYNC
This menu allow to adjust the PWM
frequency value (Hz) in order to
reduce flickering in the process of
your camera recordings

Up-Down

MENU

AUTOMATIC MODE
Automatic demo game without
DMX controller

ChPr
Chase with 16 steps previously
created in REC MODE
Speed and Wait time selectable
by user

ENTER

Up-Down

Up-Down

Up-Down

Up-DownENTER

Range = Off - 20
Default = 2

ENTER

Off = 25 ms
Istant responce to DMX variation

20 = 250 ms
Smooth response to DMX variation

Linear = Linear

Up-DownENTER

current output

ENTER

Quadratic =
Linear light

ENTER

output

Up-DownENTER

Up-DownENTER ENTER

ENTER

ENTER

Range = 610 Hz -10 KHz
Default = 610 Hz

Up-Down

Up-Down

ENTER

ENTER

CUPr
RGB values selectable by user

Up-Down

MENU

AUTOMATIC MODE
Automatic demo game without
DMX controller

Rainbow (rAIn)
Rainbow colours effect.
Speed time selectable by user

CU01-CU16
Color Macros as on DMX channel
8 (Macro)

WHITE MACROS
16 macros for White color from
2000 to 7200 ° K

DIMMER
Dimmer level selectable by user
as on DMX channel 2 (Dimmer)
Dimmer level is active for all the
programs and macros

ENTER

13

Up-DownENTER

ENTER

ENTER

ENTER

TITAN SOLO

Up-Down

ENTER

ENTER

ENTER

SHUTTER
Shutter level selectable by user
as on DMX channel 1 (Shutter)

Up-DownENTER

ENTER

Shutter level is active only for

CU01/CU16 and Wh01/Wh16
macros

Up-DownENTER

ENTER

ESC
Esc from Automatic Mode Menu

Up-Down

MENU

ENTER

ENTER

REC MODE

In DMX Recorder Mode,it is
possible to create and store the
scenes of the ChPr by using an
external DMX controller.
The unit must be setted to 9
channels MODE

DMX Recorder Mode
For the programming of ChPr by using a DMX controller, besides the 9 channels necessary to control the unit a further 3 DMX channels
are needed.
So that in RECORDER mode ( via DMX) the unit will need 12 channels to be correctly programmed.
The three new DMX channels are:

DMX channel 10 = SCENES channel
From 0-10 = no function ( r001)
From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

DMX channel 11 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.
With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene.
With the channel REC it is possible to record the selected scene as last scene.

DMX channel 12 = RECORDING channel
Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has been recorded).It is
advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene. If ChPr is
not closed, by indicating the last scene ( Edit channel between 235-255), in playback mode all 16 scenes will be played through even
if not programmed

Up-Down

MENU

SLAVE MODE
Slave mode for ChPr program.
All slave units will be
synchronised with master unit,
running their own Chpr program.

Up-Down

MENU

ENTER

14

Up-DownENTER

Up-DownENTER

ENTER

ENTER

TITAN SOLO

INFRARED MODE
Infrared remote control.
By activating Ir MODE, it will be
possible to navigate trought the
unit functions by using the D.T.S.
infrared remote control.
D.T.S. Code :0514L008
(Not implemented on TITAN
SOLO)

Up-Down

MENU

EMERGENCY
Emergency operating mode.
By setting Emergency mode, it
will be possible to select one of
the 16 preprogrammed WHITE
cues that will then run if DMX
signal is missing or not available.
Usefull for Emergency EXIT
ilumination on public areas.

Up-Down

MENU

DEFAULT
To restore default settings

ENTER

NOTE:
External infrared remote sensor
needed.
D.T.S. Code :03.LA.016
(Not implemented on TITAN
SOLO)

Up-DownENTER

Up-DownENTER

ENTER

Default = OFF

ENTER

Default = White 1

Default = 255

ENTER

ENTER

Up-Down

MENU

TEMPERATURE
Power supply temperature
visualisation (°C)

Up-Down

MENU

LIFE TIME
This menu show the total UNIT life tine
and the RGB life time

Up-Down

MENU

TEST MODE
RGB colours test with rainbow

Up-Down

MENU

SOFTWARE
Software version

ENTER

ENTER

ENTER

ENTER

Up-Down

ENTER

DISPLAY FUNCTIONS

TITAN SOLO RGBA

TITAN SOLO WHITE

15

TITAN SOLO

MENU

ENTER

DOWN

UP

DISPLAY FUNCTIONS

The TITAN SOLO FULL COLOUR display panel shows all the available functions . Using these
functions, it is possible to change some of the parameters and add some functions. Changing the
D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 signal
used to control it. Carefully follow the instructions below before carrying out any variations or
selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Software version 2.10

MENU

REVERSE DISPLAY
Reverses display's reading depending on
the mounting position
(On the ground or suspended).

DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.

ENTERUp-Down

Up-Down

Up-Down

Up-DownENTER

position

Suspension

position

Floor

Up-DownENTER

Display OFF

Display

always ON

ENTER

ENTER

ENTER

ENTER

Up-Down

DMX MODE
To select DMX mode : 10 (default) - 6 ­AUX - CUSTOM

AUX mode let you activate an external
ON -OFF control on IR connector.
(Not implemented on TITAN SOLO)

CUSTOM DMX mode let you set the
parameters for Shutter, Dimmer, Red,
Green, Blue, Ctc, Macro and Function to
the desired DMX channels.

MACRO Function, enable channel
mapping macro rainbow effects
STD (default)

Up-DownMENU ENTER

Up-Down

Up-Down

Up-Down

Up-Down

10 CHANNELS

6 CHANNELS

AUX MODE

Up-DownENTER

Up-DownENTER

ENTER

ENTER

ENTER

Default DMX Mode = 9 CH

Not implemented on
TITAN SOLO

Custom mode enabled

ENTER

Show Custom settings

ENTER

Setting the parameters
on Custom Mode

ENTER

Standard mode enabled

ENTER

(Default)

Show Custom settings

ENTER

16

TITAN SOLO

Up-Down

BOOST DRIVING
This menu allow to increase the
LED’s current from 350mA to 500 mA

MENU

ENTERUp-Down

LED
RGBA Min/Max, Smooth and Compression
level values settings

RGBA MINIMUM VALUES
This menu allow to select the
minimum levels for Red,Green, blue
and Amber

RGBA MAXIMUM VALUES
This menu allow to select the
maximum levels for Red,Green, Blue
and Amber

These settings have
priority on Master
Dimmer (DMX channel 2)

SMOOTH VALUE
This menu allow to select the value
of the delay ( in millisecons) for
RGB and Dimmer channels
reaction to DMX or Program
variation.
Off=25 ms delay (Fast response)
20=250 ms delay (Slow response)

Up-DownMENU ENTER

Up-Down

Up-Down

Up-Down

Up-Down

Up-Down

Up-Down

Boost mode activated

Boost mode deactivated

Up-DownENTER

Up-DownENTER

Up-DownENTER

Up-DownENTER

Up-DownENTER

ENTER

ENTER

Whit BOOST active,the LED’s
current is setted to 500mA
(30%more gain).
Default = Disable

Default = 0

Default = 255

Default = 0

Default = 255

Default = 0

Default = 255

Default = 0

Default = 255

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

Range = Off - 20
Default = 2

Off = 25 ms
Istant responce to DMX variation

20 = 250 ms
Smooth response to DMX variation

ENTER

COMPRESSION
This menu allow to select between
Linear current output or Quadratic
current output for LEDs
Default = Linear

SYNC
This menu allow to adjust the PWM
frequency value (Hz) in order to
reduce flickering in the process of
your camera recordings

Up-Down

MENU

AUTOMATIC MODE
Automatic demo game without
DMX controller

ChPr
Chase with 16 steps previously
created in REC MODE
Speed and Wait time selectable
by user

CUPr
RGB values selectable by user

ENTER

Up-Down

Up-Down

Up-DownENTER

current output

ENTER

Quadratic =

Linear = Linear

Linear light

ENTER

output

Up-DownENTER

Up-DownENTER ENTER

ENTER

ENTER

Range = 610 Hz -10 KHz
Default = 610 Hz

Up-Down

Up-Down

ENTER

ENTER

Up-Down

MENU

AUTOMATIC MODE
Automatic demo game without
DMX controller

Rainbow (rAIn)
Rainbow colours effect.
Speed time selectable by user

CU01-CU16
Color Macros as on DMX channel
8 (Macro)

WHITE MACROS
16 macros for White color from
2000 to 7200 ° K

DIMMER
Dimmer level selectable by user
as on DMX channel 2 (Dimmer)
Dimmer level is active for all the
programs and macros

ENTER

17

Up-DownENTER

ENTER

ENTER

ENTER

TITAN SOLO

Up-Down

ENTER

ENTER

ENTER

SHUTTER
Shutter level selectable by user
as on DMX channel 1 (Shutter)

Up-DownENTER

Shutter level is active only for

CU01/CU16 and Wh01/Wh16
macros

Up-DownENTER

ESC
Esc from Automatic Mode Menu

Up-Down

MENU

ENTER

ENTER

REC MODE

In DMX Recorder Mode,it is
possible to create and store the
scenes of the ChPr by using an
external DMX controller.
The unit must be setted to 10
channels MODE

DMX Recorder Mode
For the programming of ChPr by using a DMX controller, besides the 10 channels necessary to control the unit a further 3 DMX
channels are needed.
So that in RECORDER mode ( via DMX) the unit will need 13 channels to be correctly programmed.
The three new DMX channels are:

ENTER

ENTER

DMX channel 11 = SCENES channel
From 0-10 = no function ( r001)
From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

DMX channel 12 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.
With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene.
With the channel REC it is possible to record the selected scene as last scene.

DMX channel 13 = RECORDING channel
Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has been recorded).It is
advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene. If ChPr is
not closed, by indicating the last scene ( Edit channel between 235-255), in playback mode all 16 scenes will be played through even
if not programmed

Up-Down

MENU

SLAVE MODE
Slave mode for ChPr program.
All slave units will be
synchronised with master unit,
running their own Chpr program.

Up-Down

MENU

ENTER

18

Up-DownENTER

Up-DownENTER

ENTER

ENTER

TITAN SOLO

INFRARED MODE
Infrared remote control.
By activating Ir MODE, it will be
possible to navigate trought the
unit functions by using the D.T.S.
infrared remote control.
D.T.S. Code :0514L008
(Not implemented on TITAN
SOLO)

Up-Down

MENU

EMERGENCY
Emergency operating mode.
By setting Emergency mode, it
will be possible to select one of
the 16 preprogrammed WHITE
cues that will then run if DMX
signal is missing or not available.
Usefull for Emergency EXIT
ilumination on public areas.

Up-Down

MENU

DEFAULT
To restore default settings

ENTER

NOTE:
External infrared remote sensor
needed.
D.T.S. Code :03.LA.016
(Not implemented on TITAN
SOLO)

Up-DownENTER

Up-DownENTER

ENTER

Default = OFF

ENTER

Default = White 1

Default = 255

ENTER

ENTER

Up-Down

MENU

TEMPERATURE
Power supply temperature
visualisation (°C)

Up-Down

MENU

LIFE TIME
This menu show the total UNIT life tine
and the RGBA life time

Up-Down

MENU

TEST MODE
RGB colours test with rainbow

Up-Down

MENU

SOFTWARE
Software version

ENTER

ENTER

ENTER

ENTER

Up-Down

ENTER

19

HIDDEN MENU

For technical personnel only

To operate this menu:

-Connect the unit to the main

-While reset is running, press the MENU and ENTER keys at the same time.

Reset EEPROM (Reset all settings)
ATTENTION: by pressing this key you must repeat all previous
calibrations

UPLOAD
This menu allow to upgrade the unit’s software by computer

TITAN SOLO

DOWNLOAD
This menu allow to save unit’s programs into computer

TEMPERATURE
This menu allow to set the maximum operating temperature before LEDs
reduction current control will be activated

CHANNELS
This menu allow to set 3 channels or 4 channels LEDs output mode
3 LEDs channels output mode = TITAN SOLO FULL COLOUR
4 LEDs channels output mode = TITAN SOLO RGB / TITAN SOLO WHITE

MAXIMUM LEDs OUTPUT POWER
This menu allow to set the maximum power available on LEDs (1-100 %)

MAXIMUM LEDs OUTPUT POWER
This menu allow to ativation / deactivation the adjustment lock set.
Entering the code enabling the menu item LOCH(100) after that you can enable
or dasable the adjustment lock

EXIT
Exit from hidden menu.

20

TITAN SOLO

AUTOMATIC OPERATION (AUTO):

TITAN SOLO can work in automatic mode without a DMX controller. First of all connect the projectors
with a DMX cable (picture below). A maximum quantity of 32 slave units can be connected to the same
Master unit.

MASTER SLAVE 1 SLAVE 2 SLAVE 3 SLAVE 32

OUT

IN

OUT

IN

OUT

IN

OUT

IN

To activate Auto mode on the first unit, use the menu to run through the different modes until AUTO
appears on the display, and press enter.
Now it is possible to choose between the different pre-programmed games (CUPr-RAIn-CU01/CU16­Wh01/Wh16) or ChPr which is user programmable through REC mode. To confirm game activation press
ENTER on the selected GAME.

CUPr-RAIn-CU01/CU16-Wh01/Wh16

The first unit that will work as a Master should be placed in Automatic mode (AUTO), the other units
have to be placed in 9 channels DMX mode (MODE 9CH) for TITAN SOLO FULL COLOUR or in 10
channels DMX mode (MODE 10 CH) for TITAN SOLO RGB / WHITE and the DMX address should be set
at A001. For RaIn (rainbow) game it is possible to select the speed for the colour changhing (SPEE).
DIMMER function (in AUTOMATIC MODE) is active for all the programs.
SHUTTER function (in AUTOMATIC MODE) is active only for CU01/CU16 and Wh01/Wh16 macros.

ChPr MASTER/SLAVE

The first unit that will function as a Master must be set to Automatic mode (AUTO), the other units must
be set to Slave mode (SLAV), selectable through the menu. In this way all the Slave units will be
synchronised with the master and running their own ChPr game.
On the master unit it is possible to vary the Speed time (SPEE) for the colour changhing and the Wait
time (UAIt) between the steps.
Speed time and Wait time on the Master, have priority on the slave units.
NB: It is possible to run GA.Pr on the Slave units even though these do not have GA.Pr programmed.
You can do this by setting the units to 9 ch DMX MODE for TITAN SOLO FULL COLOUR or 10 channels
DMX mode for TITAN SOLO RGB / WHITE and selecting DMX address A001.

Rec mode

It is possible to program your own game on the TITAN SOLO that will then run it in AUTO mode (ChPr).
Each unit can have its own programmed game.
In REC mode the unit must be set to 9 channels mode for TITAN SOLO FULL COLOUR and 10 channels
mode for TITAN SOLO RGB / TITAN SOLO WHITE.

To program the ChPr by using a DMX controller, you need 3 more channels in addition to the 9/10
channels necessary to control the unit.
So that in RECORDER mode (via DMX) the unit will need 12/13 DMX channels to be correctly
programmed.

21

The three new DMX channels are:

TITAN SOLO FULL COLOUR

DMX channel 10 = SCENES channel
From 0-10 = no function ( r001)
From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

DMX channel 11 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.
With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to
record the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the
sequence as last scene.
With the channel REC it is possible to record the selected scene as last scene.

DMX channel 12 = RECORDING channel
Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene
has been recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only
once you have decided to save the scene. If ChPr is not closed, by indicating the last scene ( Edit channel
between 235-255), in playback mode all 16 scenes will be played through even if not programmed

TITAN SOLO

TITAN SOLO RGB / TITAN SOLO WHITE

DMX channel 11 = SCENES channel
From 0-10 = no function ( r001)
From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

DMX channel 12 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.
With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to
record the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the
sequence as last scene.
With the channel REC it is possible to record the selected scene as last scene.

DMX channel 13 = RECORDING channel
Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene
has been recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only
once you have decided to save the scene. If ChPr is not closed, by indicating the last scene ( Edit channel
between 235-255), in playback mode all 16 scenes will be played through even if not programmed

22

DMX PROTOCOL

TITAN SOLO FULL COLOUR

9 CHANNELS MODE (Default)

1 SHUTTER
2 DIMMER
3 RED
4 GREEN
5 BLUE
6 WHITE (Pre-programmed whites at different color temperatures)
7 CTC
8 COLOURS MACRO
9 FUNCTIONS

TITAN SOLO

DMX CHANNEL

DMX range

Value

0-9
10-19
20-29
30-119

120-149
150-179
180-204
205-229
230-255

DMX CHANNEL

DMX range

Value

0-255

1

Mid point

DMX value

5
14
24

192
218

240

2

Mid point

DMX value

Parameter: SHUTTER

Move

range

(degrees)

Parameter: DIMMER

Strobe at variable speed from slow to fast (3400ms-20ms)

Pulse open at variable speed from slow to fast (43s-100ms)
Pulse close at variable speed from slow to fast (43s-100ms)

Move

range

Mode Option Function

Mode Option Function

(degrees)

Black-out

Open

Black-out

Random Strobe (Master and RGB active)

Random Strobe (Full)

Open

Proportional dimmer

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

Mid point

DMX value

Parameter: RED

3

(degrees)

Move

range

Mode Option Function

23

TITAN SOLO

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

Mid point

DMX value

Mid point

DMX value

DMX range Mid point

Value DMX value

0-55 23

56-105

106-155

Parameter: GREEN

4

Move

range

Mode Option Function

(degrees)

Parameter: BLUE

5

Move

range

Mode Option Function

(degrees)

6

Parameter: WHITE (Pre-programmed White at diff. color temperature)

Move

Mode Option Function

No Function

Full (Red-Green-Blue at Full)

White DTS

80
130

range

(degrees)

IF CHANNEL 9 (FUNCTIONS) = CUSTOM WHITE RECALL (Dmx range value 0 - 79)

156-205

206-255

180

225

White CTC (Channel 7 CTC enabled
43 color temp. Correction Macros: 2000°K-7200°K)

Custom White Recall

IF CHANNEL 9 (FUNCTIONS) = CUSTOM WHITE CREATE (Dmx range value 80 - 160)

156-205

206-255

180

225

Custom White Create (RGB levels selectable by DMX)

White CTC (Channel 7 CTC enabled
43 color temp. Correction Macros: 2000°K-7200°K)

DMX CHANNEL

DMX range Mid point

Value DMX value

7

Parameter: CTC (Color temperature correction)

Move

range

(degrees)

Mode Option Function

IF CHANNEL 6 (White) = WHITE CTC (Dmx range value 206 - 255)

0-255

43 color temp. Correction Macros: 0 = 2000°K / 128 = 5500°K / 255 = 7200°K

IF CHANNEL 6 (White) = NO FUNCTION (Dmx range value 0 - 43)

0-255

Smooth RGB linear Hue correction

DMX CHANNEL

8

24

Parameter: COLOUR MACROS

TITAN SOLO

IF:

MENU

Up-Down

DMX range

Value

0-14
15-29
30-44
45-59
60-74
75-89
90-104

105-119
120-134
135-149
150-164
165-179
180-194

195-209
210-225

226-239
240-255

DMX value

ENTER

Mid point

Up-Down

Move

range

(degrees)

PLEASE CHECK PAGE 11

ENTER

Up-Down

ENTER

Mode Option Function

No Function
Macro 1
Macro 2
Macro 3

Macro

Macro 4
Macro

Macro 5
Macro

Macro 6
Macro

Macro 7
Macro

Macro 8
Macro

Macro 9

Macro

Macro 10
Macro

Macro 11
Macro

Macro 12

Macro

Macro 13
Macro

Macro 14
Macro

Macro 15
Macro 16

DMX CHANNEL

IF:

MENU

Up-Down

DMX range

Value

0-14
15-22
23-30
31-38
39-46
47-54
55-62
63-70
71-78
79-86
87-94
95-102

103-110

111-118

119-126
127-134
135-142

DMX value

8

ENTER

Mid point

Parameter:

Up-Down

Move
range

(degrees)

COLOUR MACROS

ENTER

Up-Down

Mode Option

PLEASE CHECK PAGE 11

ENTER

Function

No Function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8

Macro 9
Macro 10
Macro 11
Macro 12

Macro 13
Macro 14
Macro 15

Macro 16

DMX CHANNEL

25

8

Parameter:

COLOUR MACROS

TITAN SOLO

IF:

MENU

Up-Down

DMX range

Value

143-150
151-158
159-166
167-174
175-182
183-190
191-198
199-206
207-214

215-222
223-230

231-238
239-246
247-255

DMX CHANNEL

ENTER

Mid point

DMX value

9

Parameter:

PLEASE CHECK PAGE 11

Up-Down

ENTER

Up-Down

ENTER

Move
range Mode Option Function

(degrees)

Rainbow Speed 1 (1 Sec.)
Rainbow Speed 2 (5 Sec.)
Rainbow Speed 3 (10 Sec.)

Rainbow Speed 4 (20 Sec.)
Rainbow Speed 5 (30 Sec.)
Rainbow Speed 6 (60 Sec.)
Rainbow Speed 7 (120 Sec.)

Rainbow Speed 8 (180 Sec.)
Random Speed 1 (0.5 sec.)
Random Speed 2 (1 Sec.)
Random Speed 3 (2 Sec.)
Random Speed 4 (5 Sec.)
Random Speed 5 (10 Sec.)
Random Speed 6 (30 Sec.)

FUNCTIONS (Recall,Create and Store the Custom white)

DMX range

Value

79-

0

160

-

80

161-255

Mid point

DMX value

Move
range

(degrees)

Custom White Recall (Enable CH 7 for Custom white Recall)

Custom White Create (Enable CH 7 for Custom white Creation)

Custom White Store (Store the Custom White created )

Mode

Option

Function

26

TITAN SOLO

6 CHANNELS MODE (For use with DTS Wall mounted DMX controller 0514L007)

1 GREEN
2 RED
3 BLUE
4 DIMMER
5 NOT USED
6 SHUTTER

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

1

Parameter: GREEN

Mid point

DMX value

2

Parameter: RED

Mid point

DMX value

3

Parameter: BLUE

Mid point

DMX value

Move

range

Mode Option Function

(degrees)

Move

range

Mode Option Function

(degrees)

Move

range

Mode Option Function

(degrees)

0-255 Proportional colour

DMX CHANNEL

4

Parameter: DIMMER

DMX range

Value

0-255

DMX CHANNEL

DMX range

Value

0-255

Mid point

DMX value

5

Parameter: NOT USED

Mid point

DMX value

Move

range

Mode Option Function

(degrees)

Move

range

Mode Option Function

(degrees)

Proportional dimmer

No Function

DMX CHANNEL

DMX range

Value

0-9
10-19
20-29
30-119

120-149
150-179
180-204
205-229
230-255

6

Parameter: SHUTTER

Mid point

DMX value

5
14
24

192
218

240

Move

(degrees)

range

Mode Option Function

Strobe at variable speed from slow to fast (3400ms-20ms)

Pulse open at variable speed from slow to fast (43s-100ms)
Pulse close at variable speed from slow to fast (43s-100ms)

Black-out

Open

Black-out

Random Strobe (Master and RGB active)

Random Strobe (Full)

Open

27

DMX PROTOCOL

TITAN SOLO RGBA

10 CHANNELS MODE (Default)

1 SHUTTER
2 DIMMER
3 RED
4 GREEN
5 BLUE
6 AMBER
7 WHITE (Pre-programmed whites at different colour temperatures)
8 CTC
9 COLOURS MACRO
10 FUNCTIONS

TITAN SOLO

DMX CHANNEL

DMX range

Value

0-9
10-19
20-29
30-119

120-149
150-179
180-204
205-229
230-255

DMX CHANNEL

DMX range

Value

0-255

1

Mid point

DMX value

5
14
24

192
218

240

2

Mid point

DMX value

Parameter: SHUTTER

Move

range

(degrees)

Parameter: DIMMER

Strobe at variable speed from slow to fast (3400ms-20ms)

Pulse open at variable speed from slow to fast (43s-100ms)
Pulse close at variable speed from slow to fast (43s-100ms)

Move

range

Mode Option Function

Mode Option Function

(degrees)

Black-out

Open

Black-out

Random Strobe (Master and RGBA active)

Random Strobe (Full)

Open

Proportional dimmer

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

Mid point

DMX value

Parameter: RED

3

(degrees)

Move

range

Mode Option Function

28

TITAN SOLO

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

Mid point

DMX value

Mid point

DMX value

Mid point

DMX value

Parameter: GREEN

4

Move

range

(degrees)

Parameter: BLUE

5

Move

range

(degrees)

Parameter: AMBER

6

Move

range

(degrees)

Mode Option Function

Mode Option Function

Mode Option Function

DMX CHANNEL

DMX range Mid point

Value DMX value

0-55 23

56-105

106-155

7

80
130

Parameter: WHITE (Pre-programmed White at diff. color temperature)

Move

range

(degrees)

Mode Option Function

No Function

Full (Red-Green-Blue at Full)

White DTS

IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE RECALL (Dmx range value 0 - 79)

156-205

206-255

180

225

White CTC (Channel 8 CTC enabled
43 color temp. Correction Macros: 2000°K-7200°K)

Custom White Recall

IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE CREATE (Dmx range value 80 - 160)

156-205

206-255

180

225

Custom White Create (RGB levels selectable by DMX)

White CTC (Channel 8 CTC enabled
43 color temp. Correction Macros: 2000°K-7200°K)

29

DMX CHANNEL

DMX range Mid point

Value DMX value

8

Parameter: CTC (Color temperature correction)

Move

range

(degrees)

Mode Option Function

IF CHANNEL 7 (White) = WHITE CTC (Dmx range value 206 - 255)

TITAN SOLO

0-255

43 color temp. Correction Macros: 0 = 2000°K / 128 = 5500°K / 255 = 7200°K

IF CHANNEL 7 (White) = NO FUNCTION (Dmx range value 0 - 43)

0-255

DMX CHANNEL

IF:

MENU

Up-Down

DMX range

Value

9

ENTER

Mid point

DMX value

Parameter: COLOUR MACROS

Smooth RGB linear Hue correction

Up-Down

ENTER

Move

range

(degrees)

Mode Option Function

Up-Down

PLEASE CHECK PAGE 15

ENTER

0-14
15-29
30-44
45-59
60-74
75-89
90-104

105-119
120-134
135-149
150-164
165-179
180-194

195-209
210-225

226-239
240-255

No Function
Macro 1
Macro 2
Macro 3

Macro

Macro 4
Macro

Macro 5
Macro

Macro 6
Macro

Macro 7
Macro

Macro 8
Macro

Macro 9

Macro

Macro 10
Macro

Macro 11
Macro

Macro 12

Macro

Macro 13
Macro

Macro 14
Macro

Macro 15
Macro 16

DMX CHANNEL

9

30

Parameter: COLOUR MACROS

TITAN SOLO

IF:

MENU

DMX range

Value

0-14
15-22
23-30
31-38
39-46
47-54
55-62
63-70
71-78
79-86
87-94
95-102

103-110

111-118

119-126
127-134
135-142
143-150
151-158
159-166
167-174
175-182
183-190
191-198
199-206
207-214

215-222
223-230

231-238
239-246
247-255

Up-Down

DMX value

ENTER

Mid point

Up-Down

Up-Down

ENTER

Move
range Mode Option

(degrees)

PLEASE CHECK PAGE 15

ENTER

Function

No Function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8

Macro 9
Macro 10
Macro 11
Macro 12

Macro 13
Macro 14
Macro 15

Macro 16
Rainbow Speed 1 (1 Sec.)
Rainbow Speed 2 (5 Sec.)
Rainbow Speed 3 (10 Sec.)

Rainbow Speed 4 (20 Sec.)
Rainbow Speed 5 (30 Sec.)
Rainbow Speed 6 (60 Sec.)
Rainbow Speed 7 (120 Sec.)

Rainbow Speed 8 (180 Sec.)
Random Speed 1 (0.5 sec.)
Random Speed 2 (1 Sec.)
Random Speed 3 (2 Sec.)
Random Speed 4 (5 Sec.)
Random Speed 5 (10 Sec.)
Random Speed 6 (30 Sec.)

DMX CHANNEL

10

DMX range Mid point

Value DMX value

0-79

80-160

161-255

Parameter: FUNCTIONS (Recall,Create and Store the Custom white)

Move

range

(degrees)

Custom White Recall (Enable CH 6 for Custom white Recall)

Mode Option Function

Custom White Create (Enable CH 6 for Custom white Creation)

Custom White Store (Store the Custom White created )

31

DMX PROTOCOL

TITAN SOLO WHITE

10 CHANNELS MODE (Default)

1 SHUTTER
2 DIMMER
3 WHITE 1
4 WHITE 2
5 WHITE 3
6 AMBER
7 WHITE (Pre-programmed whites at different colour temperatures)
8 CTC
9 COLOURS MACRO
10 FUNCTIONS

TITAN SOLO

DMX CHANNEL

DMX range

Value

0-9
10-19
20-29
30-119

120-149
150-179
180-204
205-229
230-255

DMX CHANNEL

DMX range

Value

0-255

1

Mid point

DMX value

5
14
24

192
218

240

2

Mid point

DMX value

Parameter: SHUTTER

Move

range

(degrees)

Parameter: DIMMER

Strobe at variable speed from slow to fast (3400ms-20ms)

Pulse open at variable speed from slow to fast (43s-100ms)
Pulse close at variable speed from slow to fast (43s-100ms)

Random Strobe (Master and White 1-3 + Amber active)

Move

range

Mode Option Function

Mode Option Function

(degrees)

Black-out

Open

Black-out

Random Strobe (Full)

Open

Proportional dimmer

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

Mid point

DMX value

Parameter: WHITE 1

3

Move

range

(degrees)

Mode Option Function

32

TITAN SOLO

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

Mid point

DMX value

Mid point

DMX value

Mid point

DMX value

Parameter: WHITE 2

4

Move

range

(degrees)

Parameter: WHITE 3

5

Move

range

(degrees)

Parameter: AMBER

6

Move

range

(degrees)

Mode Option Function

Mode Option Function

Mode Option Function

DMX CHANNEL

DMX range Mid point

Value DMX value

0-55 23

56-105

106-155

7

80
130

Parameter: WHITE (Pre-programmed White at diff. color temperature)

Move

range

(degrees)

Mode Option Function

No Function

Full (Red-Green-Blue-Amber at Full)

White DTS

IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE RECALL (Dmx range value 0 - 79)

156-205

206-255

180

225

White CTC (Channel 8 CTC enabled
43 color temp. Correction Macros: 2000°K-7200°K)

Custom White Recall

IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE CREATE (Dmx range value 80 - 160)

156-205

206-255

180

225

Custom White Create (RGB levels selectable by DMX)

White CTC (Channel 8 CTC enabled
43 color temp. Correction Macros: 2000°K-7200°K)

33

DMX CHANNEL

DMX range Mid point

Value DMX value

8

Parameter: CTC (Color temperature correction)

Move

range

(degrees)

Mode Option Function

IF CHANNEL 7 (White) = WHITE CTC (Dmx range value 206 - 255)

0-255

43 color temp. Correction Macros: 0 = 2000°K / 128 = 5500°K / 255 = 7200°K

IF CHANNEL 7 (White) = NO FUNCTION (Dmx range value 0 - 43)

0-255

DMX CHANNEL

9

Parameter: COLOUR MACROS

Smooth RGB linear Hue correction

TITAN SOLO

IF:

Up-Down

MENU

DMX range

Value

0-14
15-29
30-44
45-59
60-74
75-89
90-104

105-119
120-134
135-149
150-164
165-179
180-194

195-209
210-225

226-239
240-255

DMX value

ENTER

Mid point

Up-Down

(degrees)

Move

range

PLEASE CHECK PAGE 15

ENTER

Up-Down

ENTER

Mode Option Function

No Function
Macro 1
Macro 2
Macro 3

Macro

Macro 4
Macro

Macro 5
Macro

Macro 6
Macro

Macro 7
Macro

Macro 8
Macro

Macro 9

Macro

Macro 10
Macro

Macro 11
Macro

Macro 12

Macro

Macro 13
Macro

Macro 14
Macro

Macro 15
Macro 16

DMX CHANNEL

IF:

Up-Down

MENU

DMX range

Value

0-14
15-22
23-30
31-38
39-46
47-54
55-62
63-70
71-78
79-86
87-94
95-102

103-110

111-118

119-126
127-134
135-142
143-150
151-158
159-166
167-174
175-182
183-190
191-198
199-206
207-214

215-222
223-230

231-238
239-246
247-255

DMX value

9

ENTER

Mid point

Parameter:

Up-Down

Move
range

(degrees)

34

COLOUR MACROS

ENTER

Up-Down

Mode Option

TITAN SOLO

PLEASE CHECK PAGE 15

ENTER

Function

No Function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8

Macro 9
Macro 10
Macro 11
Macro 12

Macro 13
Macro 14
Macro 15

Macro 16
Rainbow Speed 1 (1 Sec.)
Rainbow Speed 2 (5 Sec.)
Rainbow Speed 3 (10 Sec.)

Rainbow Speed 4 (20 Sec.)
Rainbow Speed 5 (30 Sec.)
Rainbow Speed 6 (60 Sec.)
Rainbow Speed 7 (120 Sec.)

Rainbow Speed 8 (180 Sec.)
Random Speed 1 (0.5 sec.)
Random Speed 2 (1 Sec.)
Random Speed 3 (2 Sec.)
Random Speed 4 (5 Sec.)
Random Speed 5 (10 Sec.)
Random Speed 6 (30 Sec.)

DMX CHANNEL

DMX range

Value

0-79

80-160

161-255

Mid point

DMX value

10

Parameter: FUNCTIONS (Recall,Create and Store the Custom white)

Move

range

(degrees)

Custom White Recall (Enable CH 7 for Custom white Recall)

Mode Option Function

Custom White Create (Enable CH 7 for Custom white Creation)

Custom White Store (Store the Custom White created )

NOTES

35

TITAN SOLO

The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its
products without prior notice. D.T.S. assumes no responsibility for the use or application of the
products or circuits described herein.

MADE IN ITALY

*0517I085*

0517I085

D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy

Tel. [phone] Fax [phone] [e-mail] www.dts-lighting.it