DSC LCD55O1Z32-433 Installation Manual

Page 1

WARNING: Please refer to the System Installation Manual for

information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.

Installation Manual

DLS-3 v1.3 or higher

LCD55O1Z32-433 NA

version 4.1

Page 2

Table of Contents

T A B L E O F C O N T E N T S

Introduction 1

Section 1: Installation 2

1.1 Unpacking ................................................................................................................. 2

1.2 Mounting .................................................................................................................... 2

1.3 Wiring .......................................................................................................................... 2

1.4 Applying Power......................................................................................................... 3

1.5 Enrolling the Keypad ................................................................................................ 3

Section 2: Keypad Programming 5

2.1 Programming the Keypad ...................................................................................... 5

2.2 Function Key Options ............................................................................................... 5

2.3 Clock Options............................................................................................................ 5

2.4 Alarms Displayed While Armed Option................................................................. 6

2.5 Emergency (Fire, Auxiliary, Panic) Key Options ................................................... 6

2.6 Door Chime Options ................................................................................................ 6

Section 3: Receiver Programming 8 Enroll & Program Devices 8

3.1 Electronic Serial Numbers ........................................................................................ 8

3.2 Enroll Wireless Devices Using Zones ........................................................................ 8

3.3 Enroll & Program Wireless Keys ............................................................................... 9

3.4 Identified Wireless Keys .......................................................................................... 10

3.5 Enrolling & Programming Handheld Keypads.................................................... 11

Section 4: Other Programming 12

4.1 Program Zones and Partitions ............................................................................... 12

4.2 Enable Receiver Supervision ................................................................................. 12

4.3 Enable Supervision of Wireless Zones ................................................................... 12

4.4 RF Jam Detect Zone............................................................................................... 13

4.5 Receiver Software Default .................................................................................... 13

Section 5: Testing & Mounting 15

5.1 Test the placement of wireless devices............................................................... 15

5.2 Test WLS909 and WLS919 Reception .................................................................... 16

Section 6: Additional Notes 17

6.1 Trouble Conditions .................................................................................................. 17

6.2 Replacing Batteries in Wireless Devices .............................................................. 17

Section 7: Troubleshooting 18

Section 8: Programming Worksheets 19

Appendix A: Guidelines for Locating Smoke Detectors 26

Page 3

Introduction

I N T R O D U C T I O N

Introduction

The LCD5501Z32-433 keypad combines a standard PC5132 receiver with an LCD5501Z keypad that presents system status using an LCD-style display with fixed messages. With the addition of the keypad, the control panel will now support up to 32 zones. The LCD5501Z32-433 is compatible with the following DSC security systems:

• PC5010 (all versions) • PC1555 v2.3 and higher • PC5008 v2.3 and higher

• PC5015 (all versions) • Power608 v2.3 and higher • PC580 v2.3 and higher

• PC5020 (all versions)

NOTE: Control panels previous to version 2.3 support 8 wireless zones. NOTE: Only one LCD5501Z32 keypad can be connected per system. If more keypads

are required please select other DSC compatible keypads f or the system being installed.

Specifications and Features

• Maximum Current Draw: 260mA (with back lighting boost on)

• Frequency: 433.92 mHz

• Zones - receiver can receive signals from up to 32 wireless zones

• Supervisory - programmable supervisory window, one to 24 hours

• Location

- can be wired up to 1000 ft. / 305 m from the main panel with 22 gauge wire

- for longer wire runs, thicker gauge wire must be used.

• Compatibility: The LCD5501Z32-433 can be connected to the following panels: PC5010, PC5015, PC5020, PC5008, PC1555, PC580

• Connects to control panel via 4-wire Keybus

• One keypad zone input

• Optional tamper version

• Five programmable function keys

• Ready (green), Armed (red) and Trouble (yellow) status lights

Page 4

Installation

S E C T I O N 1

1.1 Unpacking

The LCD5501Z32-433 package includes the following parThe LCD5501Z32-433 package includes the following par

The LCD5501Z32-433 package includes the following par

The LCD5501Z32-433 package includes the following parThe LCD5501Z32-433 package includes the following par

• One LCD5501Z32-433 keypad

• One 5.6K Ohm resistor

• Four mounting screws

• One keypad inner door label

• One set of Fire, Auxiliary and Panic key labels

• One LCD5501Z User Sheet

• One LCD5501Z32-433 Installation Manual

1.2 Mounting

You should mount the keypad where it is accessible to designated points of entry and exit. Once you have selected a dry and secure location, perform the following steps to mount the keypad:

1. Remove the keypad backplate by loosening the screw located at the base of the unit.

2. Secure the keypad backplate to the wall in the desired location. Use the screws provided.

3. Before attaching the keypad to its backplate, complete the keypad wiring as described in the next section.

1.3 Wiring

1. Before beginning to wire the unit, ensure that all power (AC transformer and battery) is disconnected from the control panel.

2. Connect the four Keybus wires from the control panel (red, black, yellow and green) to the keypad terminals (R B Y G). Consult the diagram below:

ts:ts:

ts:

ts:ts:

3. You can connect a device, such as a door contact, to the “Z” terminal of the LCD5501Z32-

433. This eliminates the need to run wires back to the control panel for the device. To connect the zone, run one wire from the device to the Z terminal and the other wire from the device to the B (black) terminal. For powered devices, run the red wire to the R (positive) terminal and the black wire to the B (negative) terminal. When using end of line supervision, connect the zone according to one of the configurations outlined in your system’s

Installation Manual

Page 5

I N S T A L L A T I O N

1.4 Applying Power

Once all wiring is complete, apply power to the control panel:

1. Connect the battery leads to the battery.

2. Connect the AC transformer.

For more information on control panel power specifications, see the control panel

Installation Manual

NOTE: Do not connect the power until all wiring is complete.

1.5 Enrolling the Keypad

Once all wiring is complete, you will need to enter a 2-digit number that tells the system the partition and slot assignment of the keypad.

If your system has partitions, you will also need to assign the keypad to a partition (1st digit).

The slot assignment (2nd digit) tells the panel which keypad slots are occupied. The panel can then generate a fault when a keypad supervisory signal is not present. There are eight available slots for keypads. LCD5501Z32-433 keypads are always assigned to slot 1 by default. You will need to assign each keypad to its own slot (1 to 8).

NOTE: The LCD5501Z32-433 enrolls as tw o modules:

1 = keypad section of the LCD5501Z32-433

17 = receiver section of the LCD5501Z32-433

Enter the following at each keypad installed on the system:

1. Enter Installer Programming by pressing [*][8][Installer’s Code]

2. Press [000] for Keypad Programming

3. Press [0] for Partition and Slot Assignment

4. Enter a two digit number to specify the partition and slot assignment.

NOTE: If your system does not have partitions, enter [1] for the first digit.

1st digit Enter 0 for Global Keypad

Enter 1 for Partition 1 Keypad Enter 2 for Partition 2 Keypad

2nd digit Enter 1 to 8 for Slot Assignment

5. Press the [#] key twice to exit programming.

6. After assigning all keypads, perform a supervisory reset by entering [*][8][Installer’s Code][902]. The panel will now supervise all assigned keypads and enrolled modules on the system.

T o revie w whic h modules the control panel is currentl y supervising:

1. Enter [✱][8][Installer’s Code]

2. Enter [903] to display all modules. On the scroll on the keypad to indicate that the designates the keypad section, and supervised. If using an LCD5501Z keypad, scroll until the module name appears on the display.

3. To exit press [#].

LCD5501Z32-433 keypad,

LCD5501Z32-433 is present on the system.

1717

17 is used to show the receiver section is also

1717

1 and

7 will

Page 6

I N S T A L L A T I O N

If both modules do not show on the keypad, one of the following conditions may be present:

• the keypad is not connected properly to the Keybus

• there is a problem with the Keybus wiring run

• the keypad does not have enough power

1.6 Downloading

This product has an integrated PC5132-433 v4.1 receiver. When downloading to this keypad, please select the PC5132-433 v4.1 file. DLS-3 v1.3 and greater must be used in order to have the capability of downloading to this keypad.

Page 7

Keypad Programming

S E C T I O N 2

2.1 Programming the Keypad

There are several programming options available for the LCD5501Z32-433 keypad. These are described below. Record all your programming choices in the programming worksheets included in this manual.

Programming the LCD5501Z32-433 is similar to programming the rest of the system. When you are in the LCD5501Z32-433 programming sections, the keypad will display which options are turned on along the top of the display. To turn an option on or off, press the number corresponding to the option on the number pad. The numbers of the options that are currently turned ON will be displayed.

For example, if options 1 and 2 are on, the display will look like this:

For information on programming the rest of your security system, please refer to your system’s

Installation Manual

2.2 Function Key Options

The function keys are programmed in sections [1] to [5]. By default, the 5 function keys on the keypad are programmed as Stay Arm (03), Away Arm (04), Chime (06), Sensor Reset (14) and Quick Exit (16). You can change the function of each key on every keypad. Please see your system’s the keys, and a complete list of all the function key options available for your system.

2.3 Clock Options

The LCD5501Z32-433 will display the current time after 30 seconds of no key presses. To set the correct time and date for the system, please refer to your system’s the following options. To change the clock options:

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

3. Enter section [6] to go to clock options.

4. To turn any of the options on or off, press [1], [2], or [3]:

NOTE: If the Time does not display on keypad option is selected, make sure that the Keypad displays time when zones are open option is also selected.

5. When you are finished programming the clock options, press [#] to exit.

Instruction Manual

[1] ON = Time displays on keypad

OFF = Time does not display on keypad

[2] ON = Clock display is in AM/PM format

(e.g. 08:00 AM)

OFF = Clock display is in 24-hour format (e.g. 20:00)

[3] ON = Keypad does not display time when zones are open

OFF = Keypad displays time when zones are open

Installation Manual

. You can change how the keypad displays the time with

for instructions on programming

Page 8

K E Y P A D P R O G R A M M I N G

2.4 Alarms Displayed While Armed Option

You can disable the display of alarms on the keypad when the system is armed. The display of alarms is enabled by default. To disable the display of alarms when the system is armed, turn off section [6], option [5]:

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

3. To turn the display of alarms on or off, enter section [6].

4. Turn option [5] on or off:

[5] ON = Alarms not displayed while system is armed

OFF = Alarms are always displayed while system is armed

5. When you are finished, press [#] to exit.

2.5 Emergency (Fire, Auxiliary, Panic) Key Options

You can enable or disable the Fire, Auxiliary and Panic keys at each keypad. These keys are enabled by default. Please see your system’s information on these keys and their options. To turn any of the emergency keys on or off on the keypad:

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

3. Enter section [7].

4. To turn the emergency key options on or off, press [1], [2], or [3]:

[1] ON = Fire key enabled

OFF = Fire key disabled

[2] ON = Auxiliary key enabled

OFF = Auxiliary key disabled

[3] ON = Panic key enabled

OFF = Panic key disabled

5. When you are finished, press [#] to exit.

Installation Manual

for more

2.6 Door Chime Options

You can program the LCD5501Z32-433 keypad to sound a tone when any zone is opened or closed. There are two parts to the LCD5501Z32-433 door chime programming:

• Program if the LCD5501Z32-433 will chime when zones are opened and/or closed.

• Program the type of sound the LCD5501Z32-433 will make when an individual zone is

opened or closed.

For the door chime feature to work, you will also need to turn on the Door Chime attribute for each zone that will trigger the chime. This programming is done in the control panel software. Refer to your control panel’s information.

Installation Manual

for more

Door Chime on Zone Openings/Closings

You can program each LCD5501Z32-433 keypad to sound a door chime when zones are opened and/or when they are closed. By default, LCD5501Z32-433 keypads are programmed to sound door chimes on both zone openings and closings.

To change the door chime opening/closing settings, at each LCD5501Z32-433 keypad:

Page 9

K E Y P A D P R O G R A M M I N G

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

3. Enter section [6].

4. To turn the options on or off, press [6] or [7]:

[6] ON = Door Chime Enabled for Zone Openings

OFF = Door Chime Disabled for Zone Openings

[7] ON = Door Chime Enabled for Zone Closings

OFF = Door Chime Disabled for Zone Closings

5. When you are finished, press [#] to exit.

Door Chime Sounds

You can program the LCD5501Z32-433 keypad to make different door chime sounds for individual zones, or groups of zones. Each LCD5501Z32-433 keypad can make any of four door chime sounds for each zone that triggers the door chime:

· 4 quick beeps (default sound)

·‘Bing – Bing’ tone

·‘Ding – Dong’ tone

·‘Alarm’ tone

NOTE: For a zone to be able to trigger the door chime sound, the Door Chime zone attribute must also be enabled in the control panel progr amming. Please see y our control panel Installation Manual.

To change the door chime sounds:

1. Enter [*][8][Installer’s code].

2. Enter [*] to go to door chime sound programming.

3. Enter a 2-digit number for the zone you want to program [01] - [32].

4. Turn one of the following options on by pressing [1], [2], [3], or [4]:

[1] 4 quick beeps (default sound) [2] ‘Bing – Bing’ tone [3] ‘Ding – Dong’ tone [4] ‘Alarm’ tone

NOTE: Mak e sure that only one of the abov e options is turned on. If more than one is on, the keypad will sound the first option that is enabled. If none of the options are selected, the keypad will not make any sound when the zone is opened or closed.

5. To program the door chime sound for another zone, repeat steps 3 and 4.

6. When you are finished programming the door chime sounds, press [#] to exit.

Page 10

Receiver Programming

S E C T I O N 3

Enroll & Program Devices

This section describes how to enroll and program:

• wireless devices using zones (WLS904P, WLS906, WLS907, WLS912, WLS914 and WLS925L)

• wireless keys (WLS909, WLS919)

For more information on these devices, read the instruction sheet included with each device.

3.1 A Note about Electronic Serial Numbers

An electronic serial number (ESN) is printed on the back of each wireless device. ESNs are used to enroll the wireless devices with the LCD5501Z32-433 keypad.

In order to reduce the occurrence of wireless devices with the same serial number, 6digit serial numbers are now printed on the back of each wireless device.

NOTE: 6-digit serial numbers are only supported on the following control panels: PC5010 v2.x and higher, PC5015 v2.2, PC5020, PC5008, PC1555 and PC580.

The 6-digit serial numbers include hexadecimal digits. For instructions on programming, hexadecimal numbers, see your system

When connecting the LCD5501Z32-433 to a PC5010, PC5020 or PC5015 v1.x panel, enter 5-digit serial numbers only.

When connecting the LCD5501Z32-433 to a PC5010 v2.x, PC5015 v2.x, PC5020, PC5008, PC1555 or PC580 panel follow the instructions below.

Installation Manual

, section 4: How to Program.

Old Wireless Device ESNs

You can use older devices on all versions of the LCD5501Z32-433 keypad, even though they only have a 5-digit ESN. When using older wireless devices:

Enter [0] + 5-digit ESN

3.2 Enroll Wireless Devices Using Zones

Enroll wireless devices which use zones (universal transmitters, motion detectors, smoke detectors, and panic pendants):

1. At a system keypad, enter [✱][8][Installer’s code] to go the installer’s programming

section.

2. Enter programming section [804].

3. Enter the 2-digit number corresponding to the zone the device is to occupy ([01] to [32]).

NOTE: Hardwired and wireless devices cannot be assigned to the same z one. PC5108 zone expander modules occup y zones in 2 g roups of 4 (e.g. z ones 9-12 and zones 13-

16). None of the zones assigned to a PC5108 module may be used for wireless de-

vices. For more information on zone assignment, consult your system Installation

Manual.

4. Enter the device’s ESN. The entry ESN is being enrolled, add the digit [0] to the beginning of the ESN. (E.g., ESN=21234, enter 021234)

must

be six digits. If an older device with a 5-digit

Page 11

E N R O L L & P R O G R A M D E V I C E S

5. The device is now enrolled on the system. Record the serial number and the assigned zone number in the programming worksheets in the back of this manual.

6. Continue with steps 3 - 5 until you have enrolled all wireless devices.

7. To exit press [#].

NOTE: The devices will not work properly until you complete zone and partition programming (see section 4).

3.3 Enroll & Program Wireless Keys (WLS909/WLS919)

For wireless keys to work on the system, you need to enroll them and then program the function buttons. Wireless keys are not assigned to zones and require no zone programming. You can enroll up to 16 wireless keys on the system.

Enroll Wireless keys

1. At a system keypad, enter [✱][8][Installer’s code] to go to the Installer’s Programming

section.

2. Enter programming section [804].

3. Enter a 2-digit number [41]-[56] to assign the wireless key a slot. These numbers correspond to wireless key numbers 01-16.

4. Enter the key’s ESN. The entry is being enrolled, add the digit [0] to the beginning of the ESN. (E.g. ESN=61234, enter 061234)

5. The key is now enrolled on the system. Record the serial number and the assigned slot number in the programming worksheets in the back of this manual.

6. Repeat steps 3 - 5 until all wireless keys have been enrolled.

(PC5010, PC5020 and PC5015 only)(PC5010, PC5020 and PC5015 only)

(PC5010, PC5020 and PC5015 only) By default, all wireless keys are assigned to

(PC5010, PC5020 and PC5015 only)(PC5010, PC5020 and PC5015 only) Partition 1. To assign keys to Partition 2, enable the appropriate options in programming sections [91] and [92].

NOTE: A wireless key can only be assigned to one partition.

8. To exit press [#].

must

be six digits. If an older key with a 5-digit ESN

Program the WLS909/WLS919 Function Buttons

WLS909 wireless keys have four programmable function buttons. You must program a set of four functions for the buttons before any keys will work. After the functions are programmed, when you press and hold one of the four buttons for two seconds, the system will execute the programmed function.

For systems not using partitions: program the function buttons in section [59]. All wireless keys will have the same four functions.

For systems using 2 partitions (PC5010, PC5020 and PC5015 only): all wireless keys assigned to Partition 1 will have the four functions programmed in section [59]. All wireless keys assigned to Partition 2 will have the four functions programmed in section [60]. For example, if function button 1 in Section [59] is programmed for Stay arming, then pressing the first button on wireless keys assigned to Partition 1 will Stay arm Partition 1.

NOTE:

Wireless keys will not work when the partition they are assigned to is being

accessed for zone bypassing or programming.

Page 12

E N R O L L & P R O G R A M D E V I C E S

1. At a system keypad, enter [✱][8][Installer’s code].

2. Enter programming section [804].

3. Enter programming section [59] for keys assigned to partition 1, or [60] for keys assigned to partition 2.

4. For each of the 4 function buttons, enter the 2-digit number of the function you want to select. See the programming worksheets for a list of function key options.

5. Record your programming choices in the worksheets in the back of the manual.

6. To exit press [#].

3.4 Identified Wireless Keys

Reporting by the system of openings/closings by individual wireless keys and

command output [✱][7] activation by wireless key buttons may be supported on

certain control panels. To do this, the system will reserve access codes 17 – 32 for wireless keys 01-16 respectively. You must program one access code for each wireless

key (using [✱][5] access code programming) for this feature to work correctly.

Refer to your system Installation Manual f or information on access code programming.

Opening/Closing By Wireless Key Reporting

NOTES: The Identified Wireless K ey Closing option is only a v ailable with the PC5010 v2.0, PC5020, PC5008 v2.0 and higher by turning section [015] option 4 off.

The Identified Wireless Key Opening option is only available with the PC1555 v2.1, PC580 v2.1, PC5008 v2.1 and higher, PC5015 v2.2 and higher by turning Section [017] Option 1 off.

To enable the reporting of

• Make sure the control panel is v2.0 or higher

• Program a valid access code for each key

• Program a closing reporting code for each key’s access code

• Disable the Quick Arm option in section [015] option [4]

To enable the reporting of

• Make sure the control panel is v2.1 or higher

• Program a valid access code for each key

• Program an opening reporting code for each key’s access code

• Enable the WLS Key Uses Access Codes by turning section [017] option [1] off.

closings

openings

by identified wireless keys:

Command Output Activation

NOTE: The Identified Wireless K e y Command Output Activation f eature is only av ailable with the PC5010, PC5020, PC5015, PC5008, PC1555 and PC580 v2.0 and higher.

To enable command output activation by wireless keys, do the following:

• Make sure the control panel is v2.0 or higher

• Program a valid access code for each key

• Enable the PGM output attribute Requires Access Code for each PGM output

programmed as [✱][7][1-4] in sections [141] to [154].

Page 13

E N R O L L & P R O G R A M D E V I C E S

3.5 Deleting Wireless Devices

To remove a wireless device from the system, follow the guideline for adding a wireless device. Program the ESN as [000000]. The wireless device for the zone will be removed.

NOTE: You may need to remove power from the panel in order to clear troub les caused by deleted zones.

Now that you have enrolled all the wireless devices, you will need to program the system to work properly with the devices. See section 4 for more information.

Page 14

Other Programming

S E C T I O N 4

4.1 Program Zones and Partitions

Now that you have enrolled the wireless devices, you should complete all zone programming on the system. Although the exact programming required varies depending on which control panel the LCD5501Z32-433 is connected to, you should check that the following programming areas are completed correctly for each wireless zone:

• Enable zones and/or assign zones to one or more partitions (programming sections [201]-[209]).

• Program the definition for each zone (programming sections [001]-[004]).

NOTE: WLS906 wireless smoke detectors must be assigned to zones defined as Delay

24-hr fire (wireless) [87] or Standard 24-hr fire (wireless) [88] for proper supervision.

• Enable the wireless zone attribute for each wireless zone (PC580, PC1555, PC5008, PC5010 v2.0 and higher, PC5020, PC5015 v2.2 and higher only) (programming sections [101]-[132]).

See your system programming sections.

4.2 Enable Receiver Supervision

The control panel will automatically supervise the receiver via the Keybus one-minute after at least one device has been enrolled on the module. The system will generate a General System Supervisory trouble if the module is removed from the Keybus. If you need to remove the LCD5501Z32-433 from an existing system, you will have to disable supervision of the PC5132.

4.3 Enable Supervision of Wireless Zones

NOTE(for PC5010 v1.x control panels only): For UL Listed installation, Double EOL

resistors must be enabled in the PC5010 for the wireless zones to be supervised. If normally Closed or Single EOL resistors are selected the PC5010 will not be able to supervise the wireless devices. If a wireless device stops sending a supervisory signal (the unit stops functioning) the panel will not indicate a supervisory trouble condition unless Double EOL resistors are used. In addition, all hardwire zones must be wired for Double EOL resistors. For more information, refer to your PC5010 v1.x Installation Manual.

NOTE (PC5010 v2.0 and higher, PC5015 v2.2 and higher, PC5020, PC5008, PC1555, PC580 only): For wireless supervision to work, you must enable the wireless zone at-

tribute on all wireless zones (sections [101] to [132], option [8] ON).

NOTE: The RF Jam Detect zone must have the supervision option disabled.

Installation Manual

, for more information on each of the above

Wireless Supervisory Window

Each wireless zone (WLS904P, WLS906, WLS907, WLS912, WLS914, WLS925L) will send a supervisory signal every 64 minutes. If the receiver does not receive a signal within the time programmed for the Wireless Supervisory Window, it will generate a supervisory fault.

Page 15

O T H E R P R O G R A M M I N G

To program the wireless supervisory window:

1. Enter [✱][8][Installer Code] to enter Installer Programming.

2. Enter [804] to enter into Receiver Programming.

3. Enter sections [81].

4. Enter the time period for the supervisory window (8 to 24 hours).

5. To exit press [#].

Disable/Enable Zone Supervision

All wireless zones have supervision enabled by default. To disable supervision for any zone, enter the following at any system keypad:

1. Enter [✱][8][Installer Code] to enter Installer Programming.

2. Enter [804] to enter the PC5132 Module Programming.

3. Enter sections [82], [83], [84] and [85]. Disable or enable supervision for each wireless zone by turning each relevant option on or off.

4. To exit press [#].

4.4 RF Jam Detect Zone

For RF jamming detection to work, you must select an unused zone to be used as the RF Jam Detect zone. When the receiver detects an attempt to jam the RF signal, the RF Jam Detect zone will be violated and the system will generate a tamper signal. When the jamming signal is gone, the RF Jam Detect zone closes and the system sends a tamper restore signal.

To enable RF jamming detection:

1. Enter [✱][8] [Installer’s Code].

2. Enter programming section [804].

3. Select an unused zone to be the RF Jam Detect zone. Enter the 2-digit number ([01] to [32]) of the RF Jam Detect zone on the keypad, then program the serial number as [200000].

3. Enter section [93]. Enter the 2-digit number of the RF Jam Detect zone ([01] to [32]) in the programming section.

4. Disable supervision for the RF Jam detect zone by turning the relevant option off in section [82], [83], [84] or [85]. (See section 4.3 for more information.)

5. RF jamming detection is now enabled. To exit Installer programming, press [#].

4.5 Receiver Software Default

Returning the receiver programming to factory default settings is a quick way to remove all the enrolled devices from the system and reset all the programming in section [804].

NOTE: Performing this procedure will not change any programming sections except

not

[804]. Resetting the control panel to f actory default settings will to factory default settings.

return the PC5132

Page 16

O T H E R P R O G R A M M I N G

To restore the PC5132 programming to the factory default settings, perform the

O T H E R P R O G R A M M I N G

following:

1. Enter [✱][8] [Installer’s Code].

2. Enter programming section [996].

3. Enter the Installer’s Code, followed by [996] again. Press [#]. The software for the receiver section will be restored to its factory default settings.

4. Press [#] to exit Installer Programming. After a software default, you must exit and then re-enter Installer Programming before attempting to program the receiver section.

For instructions on restoring the default programming of the control panel or any other connected module, see your system

Installation Manual

Page 17

Testing & Mounting

S E C T I O N 5

5.1 Test the placement of the WLS904P, WLS906, WLS907, WLS912, WLS914 and the WLS925L

It is very important to test the proposed placement of each wireless device before it is mounted. Following these steps will test the placement of the wireless motion detectors (WLS904P/WLS914), wireless smoke detectors (WLS906), wireless glassbreak detectors (WLS912) and wireless door/window contacts (WLS907/WLS925L), based on the signal strength between the LCD5501Z32-433 and the device.

NOTE: You cannot test the Wireless Keys (WLS909/WLS919) in this mode. See section 5.2 for instructions on testing these devices. You cannot run a placement test on the RF Jam Detect zone.

1. Temporarily place the device you want to test in the place you want to mount it.

2. At a system keypad, enter [✱][8][Installer Code].

3. Enter programming section [904]. 4 Enter the 2-digit zone number for the device to be tested.

5. Activate the device being tested until a result is displayed on the keypad or sounded by the keypad or bell.

WLS904P & WLS914: Remove the detector from its backplate, wait for 1-2 seconds, then reattach the detector to its backplate. WLS906: Remove the detector from its backplate, wait for 5 seconds, then reattach the detector to its backplate. Or hold a magnet near the raised line on the outer rim. Then remove the magnet.

WLS907 & WLS925L: Open and close the contact by moving the magnet away from the unit. If the unit is attached to a door or a window, open and close the door or window to activate the device.

WLS912: Press and hold the test mode tab for 5 seconds. Release the test mode tab. The keypad will display the test result.

6. Read the test results at the keypad:

Result LED Keypad LCD Keypad Buzzer/Bell

Good Light 1 On Steady “Good” 1 Beep/Squawk

Fair Light 2 On Steady “Fair” 2 Beeps/Squawks

Bad Light 3 On Steady “Bad” 3 Beeps/Squawks

Activate the device until you get 3 good or fair results in a row. Wait 10 seconds between each test on the same device.

You may mount wireless devices where results were good or fair.

Devices indicating a bad result must be moved to another location. You may only have to move the device a few inches to correct a bad result.

NOTE: Do not mount any device where a “bad” test result was indicated.

If several wireless devices produce BAD test results, you may need to move the LCD5501Z32-433 to a better location.

7. To test another device, press [#] once, then repeat steps 4 - 6. Continue to test the devices until both the LCD5501Z32-433 and the devices are in good locations.

8. To exit installer programming, press [#] twice.

Page 18

T E S T I N G & M O U N T I N G

5.2 Test WLS909 & WLS919 Reception

The wireless key (WLS909) cannot be tested using the module placement test described above. To ensure that the LCD5501Z32-433 is receiving transmissions from these devices, conduct the following tests:

WLS909/WLS919: Use the function keys to arm and disarm the system at several different points in the installation.

If these devices do not operate from all points in the installation, you will need to move the LCD5501Z32-433 receiver. Moving the LCD5501Z32-433 higher will usually improve the reception.

If you move the LCD5501Z32-433, repeat the tests described in sections 5.1 and

5.2 on all the wireless devices. Continue to test the devices until you have found

satisfactory locations for the LCD5501Z32-433 and the WLS904P, WLS906 and WLS907 devices, and there is good reception between the LCD5501Z32-433 and the WLS909 device.

Mount the WLS904P, WLS906, WLS907, WLS912, WLS914 and WLS925L

If you have conducted the placement test described in section 5.1 and got 3 “Good” or “Fair” results in a row for each device, you can mount the wireless devices. See the

Installation Sheet

for each device for mounting instructions.

Page 19

Additional Notes

S E C T I O N 6

6.1 Trouble Conditions

The control panel always watches for possible trouble conditions. If a trouble condition

occurs, the keypad “Trouble” light will turn on and the keypad will beep. Press [✱][2]

to display the trouble conditions.

The following trouble conditions apply to the receiver portion (identified as the PC5132 by the panel) and/or any enrolled devices. For a description of all troubles, please see your system

• General System Tamper

• General System Supervisory

• Zone Fault

• Device Low Battery

• Zone Tamper

Wireless Zone Low Battery Transmission

Within the supervisory transmission, the device will indicate the status of the battery. If a battery is low, the system will indicate a Device Low Battery trouble.

The system will delay reporting the event to the central station for the number of days programmed for Zone Low Battery Transmission Delay in section [370]. This will prevent unnecessary reporting of the event if the user has been instructed on how to replace batteries.

6.2 Replacing Batteries in Wireless Devices

1 Remove the cover of the device from its backplate. This creates a tamper condition

on the zone.

2 Refer to the battery installation instructions on the

component. Be sure to note the proper orientation of the batteries as you install

them.

3 When the fresh batteries are in place, re-attach the cover to the backplate. The tamper

is restored and the zone sends a battery trouble restoral signal to the receiver. The battery trouble is now clear and the device should function normally.

NOTE: When batteries in one device need to be replaced, the batteries in all devices should be replaced at the same time.

Installation Manual

Installation Sheet

of each

Page 20

Troubleshooting

S E C T I O N 7

1. When I enter the 2-digit zone number when adding a wireless device,

the keypad gives me a long beep.

You cannot enter ESNs unless the LCD5501Z32-433 is properly connected to the Keybus. See sections 1 & 3 for instructions on setting up and wiring the PC5132 module.

2. I have entered the ESN for the device but when I violate the device, the

zone does not show open on the keypad.

Check the following:

• Ensure the ESN has been entered correctly

• Ensure that the zone is enabled for the partition (if partition programming is used).

• Ensure that the wireless zone is not assigned to a zone used by PC5108 modules.

• Ensure that the zone is programmed for something other than “Null Operation.” Wireless

smoke detectors must be assigned to zones defined as type [87] or [88].

3. When I try a module placement test I get no result or “Bad” results.

Check the following (see sections 5.1 and 5.2 for more information on testing devices):

• Verify that you are testing the correct zone

• Verify that the correct ESN was entered when the device was enrolled

• Verify that the device is in range of the LCD5501Z32-433. Try testing the device in

the same room as the receiver.

• Confirm that the LCD5501Z32-433 is properly connected to the Keybus.

• Check that you are testing the zone correctly.

• Check that the batteries are working and installed correctly.

• Look for large metal objects that may be preventing the signal from reaching the

LCD5501Z32-433.

The device must be located where consistent “Good” results are obtained. If several devices show “Bad” results, or if panic pendants and wireless keys operate inconsistently, move the receiver.

4. The LED on the motion detector does not turn on when I walk in front of

the unit.

The LED is for walk test purposes only. See your WLS904P test instructions.

Instruction Sheet

for walk

Page 21

Programming Worksheets

S E C T I O N 8

[000] Keypad Programming

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

[0] Keypad Enrollment

Valid entries are 01-18; e.g. enter [11] for partition 1, slot 1. Default = 11

1st digit Enter 0 for Global Keypad

2nd digit Enter 1 to 8 for Slot Assignment

Enter 1 for Partition 1 Keypad Enter 2 for Partition 2 Keypad

SlotSlot

Slot:

SlotSlot

I________I________I

[1]-[5] Function Key Assignments

[1] Key 1 [2] Key 2 [3] Key 3 [4] Key 4 [5] Key 5

Defaults: 03 04 06 14 16

Stay Away Chime Reset Exit

I________I________I I________I________I I________I________I I________I________I I________I________I

[6] LCD5501Z32-433 Keypad Options

Default Option On Off

ON I________I 1 Local Clock Display Enabled Display Disabled

ON I________I 2 Local Clock Displays AM/PM Displays 24-hour Time

OFF I________I 3 Open Zones Override Clock Display Do Not Override Clock

OFF I________I 4 For Future Use

OFF I________I 5 Alarms Not Displayed While Armed Always Displayed While Armed

OFF I________I 6 Door Chime Enabled for Zone Openings Door Chime Disabled

OFF I________I 7 Door Chime Enabled for Zone Closings Door Chime Disabled

OFF I________I 8 For Future Use

[7] Emergency Key Options

Default Option On Off

ON I________I 1 [F] Key Enabled [F] Key Disabled

ON I________I 2 [A] Key Enabled [A] Key Disabled

ON I________I 3 [P] Key Enabled [P] Key Disabled

OFF I________I 4-8 For Future Use

Page 22

P R O G R A M M I N G W O R K S H E E T S

[*] Door Chime Sound Programming

1. Enter [*][8][Installer’s code][*]

2. Enter 2-digit zone number [01] - [32], then select door chime sound option [1] - [4]. Repeat for each zone that is to sound a chime.

Zone Location [1] [2] [3] [4]

[01] I__________________________________________________________________I I________I I________I I________I I________I